Search Documents

By Gerhard Derge

A series of studies of the corrosion of tin is under way in the Metals Research Laboratory at the Carnegie Institute of Technology. The complete program includes examination of the corrosion properties of high-purity tin and the changes produced in these properties by the addition of varying amounts of alloying elements. Other studies of this subject have been made recently under the sponsorship of the International Tin Research and Development Council, but these researches have been confined largely to the weakly acid environments commonly encountered in the canning industry.' There is little information available regarding the corrosion of tin under alkaline conditions, but such data would be of value, for a large amount of the metal is used under such conditions. The potential measurements to be described were made because they seemed to offer the most rapid method for obtaining a general view of the conditions to be encountered in such service. These experiments will also serve to establish a technique that will be of value in further studies. It must be emphasized that the results reported are those of controlled laboratory experiments and that the conclusions drawn cannot yet be applied to service conditions; rather, they point to the directions in which more exhaustive experimental work may be done to best advantage. Experimental Procedure The first work was devoted entirely to the problem of obtaining reproducible results from a series of potential measurements. Only the methods finally adopted as standard will be described here, except when the variations from these have furnished results of interest. The cell used is shown schematically in Fig. 1. The electrolyte is contained in the vessel A (an inverted bell jar), whose ground top is fitted to the transite-board lid B. The controlled atmosphere can be admitted

Jan 1, 1938

By F. Nakhaei, M. Le Roux, Q. P. Campbell, S. Botlhoko

The results of coal sink and float tests are plotted as washability curves. Analysis of these curves indicates the most effective method by which the coal can be cleaned. Sink and float experiments are samplingdependent, destructive, and use toxic chemicals. The present research introduces an alternative method based on a 3D imaging system called RhoVol, in which the density of individual particles is determined from mass and volume measurements. A quantitative error analysis was conducted on coal sample density measurements obtained by RhoVol, and the main factors influencing the errors identified and investigated. The results show that the drawback of this technique is related to its not being able to detect hidden concavities in the particle, resulting in an overestimation of particle volume. Furthermore, it is difficult to capture the impact of porosity and cracks on the volume of coal particles obtained from 3D silhouette images. This mismatch between the RhoVol data and sink and float test results has led to attempts to apply neural network (NN) and linear regression techniques to produce a fully reliable model for correction and estimation of coal density. The NN approach offers superior predictive capability over linear regression, and the estimated density distribution is in line with the sink and float analysis. The root mean square error in estimation of density using the NN model was less than 0.05 g/cm³.

Aug 2, 2022

By G. R. Peeling

The Mining Association of Canada launched the Towards Sustainable Mining initiative in 2004. TSM's goal is to improve the mining industry's performance by aligning its actions with the priorities and values of Canadians. The initiative currently includes performance indicators for four areas: tailings management, energy use and greenhouse gas management, external outreach and corporate crisis management planning. Over the past year, the association has been designing a performance assessment and verification system for these performance areas, as its members prepare to move external verification of their performance in 2007. The initiative and its evolution, as well as the challenges faced in developing a verification system applicable to an entire sector will be examined.

Jan 1, 2007

By E. Isokangas

The production of minerals for economic use is a two-stage process, involving mining to extract the mineral from the ground, and processing to convert the mineral into a marketable product. Generally, mining and processing have been viewed as self-contained entities. Both have separate objectives, separate cost centres and key performance indicators (KPIs) that do not reflect the customer/supplier relationships that inherently exist. However, mining and processing operations are inter-connected and therefore intimately inter-related with the performance of one operation affecting the performance of another. Optimizing each stage separately without considering the whole system often misses potential economic benefits and energy savings. During the past fifteen years, the authors have been involved in implementing a holistic methodology ?Mine to Mill Process Integration and Optimisation (Mine to Mill PIO)? to maximize the overall profitability of the operation rather than just optimizing any individual process in a mining operation. Metso Process Technology and Innovation (PTI), along with their project partners, have conducted several projects to significantly increase their production- generating typically 5% to 20% higher throughput and improve the overall mine and concentrator performance through PIO methodology. This proven methodology has applications ranging from greenfield projects to long-standing operations with AG/SAG, HPGR or conventional grinding circuits. This paper explains the Mine to Mill PIO methodology and discusses the benefits of such an approach on the energy consumption, the overall costs and benefits of mining operations. The paper also summarizes several case studies illustrating the use of PTI methodology in a variety of applications. Keywords: integration, optimization, simulation, modeling, mine-to-mill, comminution, blast, drill, crushing, grinding

Sep 1, 2012

By Raden Haris Handayana, Jihan Farhan Lubis, Milia Putri, Tengku Deli Hamonangan Hasibuan, Sani Salahudin

An environmental issue that must be controlled from coal overburden blasting near the structure is ground vibration. Damaging ground vibration is the effect exerted from residual energy from blasting that does not work to fracture the rocks. Sebuku Tanjung Coal is a coal mining that operates T3 Pit adjacent to the High Voltage Tower. This structure is included in the Class 5 building with a maximum Peak Particle Velocity (PPV) of 40 mm/s. The shortest distance from the blasting location to the structure is 105 m. The initiation system used is electronic detonators combinate with emulsion as an explosives type. In Indonesia, the government regulated vibration limitation on SNI 7571:2010. The blast outcomes targeted are PPV below 40 mm/s, fragmentation size <80 cm for Excavator Komatsu PC-2000, and digging time <12 seconds. In this paper, the blast design was engineered by conducting Signature Hole Analysis for optimizing delay timing configuration and Scale Distance regression analysis to determine optimum charge weight per delay at the blast site. PPV results from 30 blastings achieved 100% below 40 mm/s with the range of about 1.773-30.250 mm/s. The deviation between PPV prediction to PPV actual is less than ±18% which provides the blasting with electronic detonator resulting in good PPV prediction for controlling vibration. The average fragmentation size (D80) is 55.81 cm in the 1st layer and 54.81 cm in the 2nd layer. The average digging time is 10.30 seconds in the 1st layer and 10.12 seconds in the 2nd layer.

Feb 6, 2023

By Julia Creasey, Natalie Hodgson, Claire Ward, Craig Davies, Helen Sarginson

"Emulsion explosive producers are attempting to lower the cost of emulsion production by using lowquality ammonium nitrate in emulsion formulations. Low quality ammonium nitrate contains additivessuch as anti-caking agents and crystal modifiers which contaminate the emulsions causing instability. This presents a need for an effective emulsifier that will maintain emulsion stability under thesechallenging conditions."

Jan 1, 2017

By Hongbo Zhu, Jinhui Peng, Linqing Dai

"To optimize the process variables for making direct reduced iron (DRI) by microwave heating, the reduction temperature, reduction time and the ratio of coal to material were studied with the central composite design (CCD) and their interactions on the Metallization rate were also investigated. The predictive polynomial quadratic equations model was analyzed by ANOVA. Optimal conditions of making DRI can be concluded as follows: 28 min at 1139?, the ratio of coal to material is 20.95%. Under these conditions, the metallization rate is up to 97.06%.1. IntroductionThere are some technical problems in making direct reduced iron (DRI) or sponge iron using iron ore concentrates containing coal and lime. In reduction of the iron ore concentrates containing coal with microwave heating, the strength of pellets needn’t to be considered. It reduces the costs and improve quality of materials, but also eliminates the need for pellet preparation process, simplifying the process and achieving a cleaner production.Microwave energy is a clean energy, and has characteristic of selective heating. The speed of heating is also fast. It researched by Chen Jin that when the mole mass of C: O is 0.627 and the microwave power is 15KW, it only spends 15min from 15? to 1021.6? with 1 kg iron ore containing coal with microwave heating [1]. There are many factors affecting metallization rate. In order to find a suitable condition for reduction process, it is necessary to design a series of suitable experiments.Response surface methodology (RSM) is one of the relevant multivariate techniques which can deal with multivariant experimental design strategy, statistical modeling and process optimization [2–5]. It is used to examine the relationship between one or more response variables and a set of quantitative experimental variables or factors. This method is often employed after the identification of the vital controllable factors to find the factor settings that optimize the response. Designs of this type are usually chosen when a curvature in the response surface is suspected. The process optimization of the microwave reduced iron ore was seldom reported in literature. Hence the present work intends to assess the effects of variables such as reduction time, reduction temperature and the ratio of coal to identify the optimum conditions using a central composite design (CCD). The characteristic of product was assessed using scanning electron microscope (SEM)."

Jan 1, 2011

By D. Wolfe, R. Cleminson

"The Aurora North mine has been operating for more than ten years, and is the source of over half of Syncrude’s bitumen production. The hydrotransport systems at Aurora experience high rates of wear, and mission lengths on current slurry pumps are nominally 1,500-2,000 hours. Recent work has enabled a better understanding of the significant adverse effect of large particle impingement damage to impeller vane leading edges - which is the known life determining issue for Aurora hydrotransport pumps. A new pump design has been developed and installed at Aurora, incorporating significantly increased impeller diameter and pumping vane lengths. The new pumps are expected to triple Aurora’s previous mission length for hydrotransport pumps. Part II of this paper will share actual hydraulic and wear performance observed in the first several months of operation, and draw comparisons relative to what was expected for these pumps in design / development.INTRODUCTION Slurry Pumps are Critical Equipment at Syncrude Slurry pumps are a key component in Syncrude’s operations. In a typical Aurora application, each 5000 HP pump stage helps move over 8,000 dry tonnes per hour of oil sand, plus an equal volume of process water that has been added to create the slurry. The average impeller life in oil sand hydrotransport service at Aurora has been nominally 1,500 to 2,000 hours, or 12 to 16 million tonnes of oil sand pumped. Generally, the slurry pump application at Aurora has proven very difficult to improve due to the unique combination of high sand abrasivity, 125 mm (5”) large particle top size (lumps), and high flow rate relative to basic pump size; a factor that results in unduly high impeller vane leading edge speeds for the service conditions."

Jan 1, 2014

By J. G. Walters

This bulletin presents, in collected and tabluated form, Bureau of Mines and American Gas Association (EM-AGA) carbonization data pertaining to the chemical analysis of tars and the characterization of tars and light oils obtained from U.S. coals.

Jan 1, 1967

By J. Illescas, N. C. Murray

This paper provides an economic comparison and technical evaluation of different approaches for copper recovery from small-scale resources such as historic tails, dumps, pond and pit water as well as acid mine/rock drainage. Factors such as the location, the availability and cost of reagents, power availability and cost and a local market for end product alter the preferred processing technique. A number of scenarios are presented and technologies considered include; solvent extraction, ion exchange, sulphide precipitation, cementation, copper sulphate crystallization, membrane (RO) and copper cathode production.

Jan 1, 2014

By Hugh P. Godard, K. Winslow

"AbstractA number of panels of various aluminum alloys in different combinations and secured by steel and three types of aluminum rivets were exposed underground at two locations in a Northern Ontario gold mine for two years and then examined to determine the extent of corrosion. The results indicate Alcan 65S-T to possess considerable advantages over Alcan 178-T, which has been employed in the construction of light skips and cages with considerable success for almost twenty years. Information on the behaviour of these alloys when used with steel rivets and in mixed combinations with themselves was obtained.IntroductionBy the complete substitution of aluminum alloys for steel in the fabrication of mining skips and cages, their weight can be reduced as much as 50 per cent. Lesser savings are possible though its savings are possible through its plates, doors, reinforcing members, etc. Reduced weight leads to economy through increased hoisting efficiency.For a new installation, the basis of design is the rate of production, which thus fixes the live load to be hoisted per trip. A lighter skip permits the use of a lighter rope and a smaller hoist. In deep shafts with high-speed hoists operated in balance, the power required for accelerating is considerable. The hoist size is determined by the weight of skip, load, and rope plus the force required to accelerate or decelerate these three elements A light skip may result in a considerably lighter rope. This is important because, even though the skip can be completely balanced this is not true of the rope. Partial balancing is possible, but conical hoist drums or other devices for this purpose are costly; thus a smaller rope results in a smaller hoist, with consequent general reduction in cost of the whole installation. A reduction in power consumption is also obtained as a result of keeping to a minimum the amount of unbalanced load and the weight of all moving parts which must be accelerated."

Jan 1, 1950

By Minerals Refining Company, Gerald Luttrell, Biao Li, Robert Bratton, Roe-Hoan Yoon, Stan Suboleski, Nikhil Gupta

Flotation is regarded as the best available method of upgrading coal and mineral fines in the mining industry. However, its efficiency deteriorates rapidly with decreasing particle size. Furthermore, ultrafine concentrates are difficult to be dewatered economically. Due to these technological problems, some operators are forced to discard at least part of the ultrafine materials to tailings (or refuse) ponds, causing significant losses of valuable resources and creating environmental concerns. To address these technological issues, a new separation process named hydrophobic-hydrophilic separation has been developed on the basis of the recent advances in the science of hydrophobic interactions. The results obtained to date show that the process can recover and dewater ultrafine particles simultaneously with high separation efficiencies. Following a series of extensive laboratory tests, the process has been scaled up to proof-of-concept and pilot-scale continuous tests. The results obtained with desliming cyclone overflows, screenbowl effluents, and by-zero coal flotation feeds can be cleaned to less than 4% ash and moisture with over 97% organic matter (or coal) recoveries. The results obtained with mineral fines also showed encouraging results.

Jan 1, 2016

"Controlling dust generation and keeping it below permissible limits at the working face of a room and pillar mine is a challenge for mine operators. With the recent changes in the respirable-dust regulation, it has become increasingly difficult. The current most effective practice of dust control at a continuous miner face in an underground mine is the use of a flooded-bed scrubber. A study carried out by the National Institute for Occupational Safety and Health (NIOSH) stated that a flooded-bed scrubber, under its optimum condition, can achieve cleaning efficiencies between 58 and 90 percent. The performance of such a system can be maintenance intensive. Other industries face similar dust control issues. The University of Kentucky partnered with Toyota Motor Manufacturing for the development of a novel wet scrubber for capturing paint overspray, with capture efficiencies in excess of 98 percent and minimal maintenance. The aim of this study is to assess the ability of this novel wet scrubber to capture respirable dust in an underground coal mine. This paper presents the conceptual design and the computational fluid dynamics (CFD) modeling of this novel wet scrubber. It discusses the results of the CFD simulation performed on the novel wet dust scrubber. INTRODUCTION Dust generation from underground coal mining is an inescapable phenomenon. No matter the practices employed, it inevitably occurs. Elevated concentrations of coal dust are potential health and safety hazards. Although dust in an underground coal mine cannot be completely avoided, its influence can be mitigated through good engineering practices. The effect of dust on the health of mining personnel has had a significant impact. The prolonged exposure of airborne respirable dust (< 5 µm) can cause coal workers’ pneumoconiosis (CWP), silicosis, emphysema, and chronic bronchitis, collectively known as black lung (U.S. Department of Labor, 2014). According to the National Institute for Occupational Safety and Health, black lung has killed more than 10,000 miners between 1995 and 2004 (NIOSH, 2008). In addition to being a health issue, coal dust is also a safety issue to the underground coal miners. The generated dust, if not captured, is dispersed into the mine air through the ventilating air and deposited downwind on the return entries’ surfaces. In the event of a methane explosion, the coal dust, if insufficiently diluted with rock dust, triggers a coal dust explosion which is much more severe than a methane explosion and causes more damage (Kenneth et al, 2006). The Jim Walters No. 5 Mine and the Upper Big Branch Mine disasters which together killed 42 people and resulted in damage worth millions of dollars in property are the examples of coal dust explosions (U.S. Department of Labor, 2001 & 2010)."

Jan 1, 2016

Now producing 35,000 tpd of coal from a deposit whose estimated reserves total 1.1 billion t, the Navajo mine of Utah International Inc. near Farmington, N. M., is the largest open-pit coal operation in the US. The history of this mine began in 1953 when, foreseeing the growing need for electrical power in the southwest, Utah International obtained a prospecting permit from the Navajo tribe. The lease, now covering 31,000 acres of the 12-million acre New Mexico-Utah-Arizona Navajo Indian reservation, was entered in 1957; in the next 3 years, Utah International negotiated with the State of New Mexico for water rights on the San Juan River, and finalized an agreement with the Arizona Public Service Co. to provide coal for the proposed Four Corners power-generating plant near Farmington.

Jan 10, 1974

By S. P. Chong, N. C. Shih, G. A. Turner

Fine powders, with the bulk of the particle diameters Jess than 10 microns, were aerated so that each particle was, on the average, separated from its neighbours by 1.3 to 2 mean diameters. In this state, measurements were made of the viscosity and settling rate of the powder, and the interfacial tension between it and a moist pellet. From the viscosity measurements, qualitative analogies are drawn between the behaviour of the aerated powder and that of a dense gas near its critical point.

Jan 1, 1970

By M. Abouhamad

According to the Canadian Urban Transit Association (CUTA), 140 Billion CAD is required to maintain, rehabilitate, and replace subway infrastructure between 2010 and 2014. The current practice adopted by transit authorities for prioritizing subway stations for rehabilitation is based on the station structural needs. While this classification is reflective of station condition, other factors, such as station size, location and passenger capacity, play an important role. The criticality of a station is an index that represents the functional importance of a station depending upon a set of identified factors. The system criticality is based on several attributes, such as station location, size, and nature of use. This paper presents a novel method of clustering subway stations for rehabilitation priority based on their criticality level. The different stations in a subway network are rated according to their relative importance against predefined attributes. The weights and scores of the attributes are computed with the help of experts and current subway network data. The analysis is done using the Fuzzy Analytic Network Process (FANP) to accommodate the subjectivity of human judgment as being expressed in natural language which entails ?fuzziness? in real-life problems and account for the interdependency between the selected attributes. The output of the model is a criticality based clustering of subway stations. The proposed framework helps authorities prioritize stations for rehabilitation and highlight stations with more criticality for a more robust asset analysis.

Aug 1, 2013

By Binbin He, Baiwei Lei, Rehamutula·Rouzi, Zheng Wang, Chao Li

Methane explosions are highly destructive and constitute a primary hazard affecting mine safety. Seals are commonly employed to obstruct the propagation of methane explosions within tunnels, with the aim of reducing the damage caused by methane explosions. In order to study the influence of the seals’ position on the parameters of methane explosion damage, this study takes the Lake Lynn Experimental Mine No. 501 in the United States as a background case. It investigates the methane/air explosion damage parameters at different positions of seals in a fully sized roadway using the GASFLOWMPI code. The coupling mechanism between methane explosion gas expansion and reflected waves is analyzed. Finally, the variation patterns of explosion damage parameters are analyzed based on explosion damage criteria. The results show that as the distance increases between the seal and the explosion source, the maximum overpressure and impulse at the seal decrease exponentially, and the decrease is more significant when the seal is closer to the explosion source. The maximum velocity and maximum dynamic pressure increase first and then decrease, reaching their maximum values at approximately 115 m. They are approximately 163.355 m/s and 30.485 kPa, respectively. According to the analysis of explosion damage criteria, it is found that overpressure damage is the main form of methane explosion damage. But the damage of impulse and dynamic pressure is not be ignored. The relative position between the seal and the gas expansion area significantly impacts the parameters of methane explosion damage due to the coupling effect of gas expansion and the overpressure reflected wave from the seal. When the seal is set in the gas expansion zone, the further the seal is from the explosion source, the greater the dynamic pressure damage and the more minor the overpressure and impulse damage. The closer to the explosion source, the more significant overpressure and impulse damage changes. When the seal is set outside the gas expansion zone, the further the seal is from the explosion source, the more minor the overpressure and impulse damage to the seal, and the dynamic pressure damage increases first and then decreases.

Apr 24, 2024

By Muhammad I. Kabir

The streamline method of recovery prediction reduces a two-dimensional problem to a bundle of one-dimensional ones. This paper presents the development and application of a novel scaling technique which, when used with a streamline model, causes s bundle of one-dimensional problems to further reduce to a single one-dimensional calculation. The one-dimensional calculation accounts for chemical-rock interactions and the streamline model for areal sweep. The scaling technique significantly reduces computation time, is readily modified to desk-top calculations, and can be applied to both absorbing and reacting species. The work was sponsored by the Interior Department&apos;s Bureau of Mines.

Jan 1, 1984

By K McSweeney, A Marton

This paper discusses the development of a strategy for ensuring long-term geotechnical stability of final pit walls at AngloGold AustraliaÆs Sunrise Dam Gold Mine. The strategy makes use of improved blasting techniques, changes to the mining sequence and other geotechnical techniques. Only the blasting techniques will be discussed in this paper. These were developed from numerous trials over a period of several months from May 2003 through to November 2003. The focus was to reduce crest loss damage and thereby improve final wall integrity, maintain designed safe berm widths, and ensure long-term stability. Crest loss mechanisms are now understood and are explained in this paper. The preferred solution is outlined; which is a combination of improved blasting and changes in the mining sequence to cater for pre-existing ground conditions. These ground conditions include dynamic hyper saline water with sometimes intersecting steeply dipping discrete structures. Project requirements were defined as mitigating or eliminating crest loss using 127 mm diameter pre-splitting and targeting minimal production blasting vibration levels against the walls. Blast results were measured by post blast visual inspections and video. Blast design input utilised the predictive algorithms built into simulation software when attempting to minimise vibration levels against the walls. Protection of the already fired pre-split line is now achieved using small charges against the wall and timing sequences which form a mask for the later firing main charges. The pre-split spacing is now modified to suit the geology. There eight blast domains identified around the perimeter of the pit, each having varying joint orientation. In addition, blasting the bench adjacent to the berm crest has particular considerations not required by the middle and lower benches. The preferred solution was to purposefully translate this damaged top section of the pre-split bench into a planned subsequent dig zone. The design of this top æweightÆ is a direct response to the nature of the crest loss mechanism.

Jan 1, 2004

By C. M. Nickerson

It is apparent that repressuring of the oil measures is becoming increasingly important to the oil industry, and is a matter that warrants the best efforts of the petroleum engineer charged with applying this method of operation to a producing property. Considerable attention has been directed to repressuring in various California oil fields, such as Dominguez and Seal Beach, which have served to sell the more progressive operator on this idea and also to keep him sold. The projects that have received most attention are in comparatively young fields where the fluid levels are high, the wells, perhaps, still flowing, where the wet gas production is of considerable volume, and where there is vital need of immediate conservation of gas, which otherwise would be blown to the air. The new State of California Gas Law, which prohibits the waste of gas, has served to interest the oil industry in means of conserving the gas that is now being blown to the air because of lack of markets. This vitally affects the operator in the older, well-depleted oil fields of the state, because in many cases he has a limited market for gas, on account of the flush production from the more active oil fields. While the waste of gas is relatively small in these older fields, such as the Midway-Sunset area, it now attains considerable importance, since under the new State Gas Law it must be put to some bcneficial use. Repressuring in the older fields of California has not received the attention of the petroleum engineers that is warranted by the present situation. This paper was prepared with the view of presenting the salient features connected with repressuring in the well-depleted oil measures of the older fields, and to show what results have already been obtained in these fields by injecting the unmarketable gas into the sands, particularly in the Midway-Sunset field in the San Joaquin Valley of California. Other projects in the older fields of the state offer some supporting data in this connection, such as the Shields Canyon and the Brea Canyon fields. Gas Storage and RepressuRing On account of the lack of market for a large portion of the dry gas produced in certain of the older, well-depleted oil fields of California, the

Jan 1, 1930