Search Documents

By Arthur E. Bruszak, Marcel Vanpée

In many practical combustion systems ignition may occur through contact with hot burned gases . Such a process plays a vital role in flame stabilization on bluff bodies . It is also of importance in the ignition of firedamp by the hot spent gases of explosives used in mines . Also , in the communication of flames through narrow channels , a problem of practical importance in flameproofing electrical equipment , the propagation of the flame is essentially a reignition process in which hot burned gases are the agent of ignition . In the actual ignition problem a great variety of conditions may be visualized . Ignition may occur where pockets of hot gases are surrounded by cold explosive mixtures or where pockets of cold mixture may be surrounded by hot gases . Alternately , a flowing stream of combustible mixture may be initially in contact with another stream of hot combustion products , or a jet of hot gases may flow into a cold quiescent mixture ; the jet may be laminar or turbulent , continuous or discontinuous . The hot gas may also consist of the oxidant ( air for instance ) and the cold combustible pure fuel . This study by the Bureau of Mines is concerned only with ignition produced by a continuous jet of gas ( hot ) flowing into a practically quiescent cold mix- The investigation of ignition by bursts of hot gases or by turbulent jets is outside the scope of this report , and work performed on this phase of the problem has been published elsewhere

Jan 1, 1963

By Diler Katircioglu-Bayel

This study aims to investigate the effect of combined mechanical and ultrasonic milling on the size reduction of talc. First, the talc sample was wet-ground in a stirred media mill for five different lengths of time (30, 60, 90, 120 and 150 min), and the optimum result was subsequently achieved with treatment by ultrasonication. The effects of amplitude (20, 35 and 50 µm), solid ratio (2.5, 5, 7.5 and 10 percent), and sonication time (60, 120 and 240 min) on the sizes of the final product were investigated. The pre-milling by wet grinding caused a decrease in the grinding resistance of talc. Sequential ultrasonic treatment, which was applied to the talc sample, generated smaller particles in comparison to those acquired by stirred media milling alone. Experimental results were assessed based on the product particle size (d10, d50 ), reduction ratio and specific energy consumption. Submicron particles prepared by ultrasonic treatment were highly stable compared to stirred media milling alone as investigated in terms of particle size. In addition, the effects of mechanical and ultrasonic milling on the structural properties of talc particles were characterized by X-ray diffraction (XRD) analysis.

By A. Boucher, D. Marcotte

"Abstract- The accepted practice for the estimation of thin (2D) vein deposits recommends the use of the grade x thickness service variable (i.e., the accumulation). Grade estimates are obtained indirectly by the estimated accumulation/estimated thickness ratio. This practice stems from the varying support (thickness) problem and the resulting non-additive nature of the grade variable. We compare the actual performance of the direct grade estimation approach used by some practitioners to that of the indirect approach using accumulation. Our simulated and real data indicate that the direct approach is more accurate for point grade estimation where the grade-thickness correlation coefficient is positive (and vice-versa). Moreover, the relative gain of the direct method increases with the (positive) correlation coefficient. This finding contradicts common thinking that the indirect approach should be the preferred method where grade-thickness correlation is strongly positive. Also, for a given positive grade-thickness correlation, the relative gain of the direct method increases with the coefficient of variation of the grade and thickness. Résumé - L’estimation de veines minces (2D) minéralisées est normalement réalisée à l’aide de la variable auxiliaire épaisseur x teneur (i.e., accumulation). Les estimés des teneurs sont alors obtenus indirectement du rapport accumulation estimée/épaisseur estimée. Cette pratique découle du problème du support variable pour la teneur, l’épaisseur de la veine, qui fait que la teneur est alors une variable non-additive. Nous comparons les performances de l’estimation directe de la teneur, utilisée par certains praticiens, à celle de l’approche indirecte. Pour l’estimation ponctuelle des teneurs, nos données simulées et réelles indiquent une meilleure justesse de l’approche directe quand la corrélation teneur-épaisseur est positive (et vice-versa). De plus, le gain relatif de la méthode directe s’accroît avec la valeur de cette corrélation (positive). Ce résultat contredit l’opinion répandue que l’approche indirecte devrait être utilisée en présence de forte corrélation positive de la teneur et de l’épaisseur. Nous montrons également que pour une corrélation positive teneur-épaisseur donnée, le gain de l’approche directe augmente avec les coefficients de variation de l’épaisseur et de la teneur."

Jan 1, 2001

By E du Plessis, J Kapusta, J L. Mauk

The world-class Bulyanhulu gold deposit (375 t Au) is in the Sukumaland greenstone belt, Northwestern Tanzania. The main mineralised quartz vein structure, termed Reef one, occurs at the contact of felsic metavolcanic rocks on the hanging wall and mafic metavolcanic rocks on the footwall. Reef one is dominated by massive quartz together with pyrite, pyrrhotite and minor chalcopyrite. Alteration in the footwall basalt is characterised by extensive chloritisation, calcification and silicification, which is strongest near the vein. Sericitisation also locally occurs adjacent to the vein. Metamorphic hornblende and plagioclase (albite) increase in abundance at a distance of 120 m from the vein and reflect the gradation into less altered rocks. The increasing abundance of chlorite, calcite, quartz and local sericite near Reef one, coupled by replacement textures suggests that most of these footwall minerals are the product of hydrothermal alteration, rather than regional metamorphism. Geochemical data shows slight enrichment in Ca, Fe and As towards the vein, whereas Zn in several drill holes becomes enriched away from Reef one. The Bulyanhulu gold deposit is a quartz-pyrite-chalcopyrite shear controlled vein with an adjacent extensive chlorite-quartz-calcite hydrothermal alteration zone (and a limited local sericite alteration zone) that passes to a hornblende-albite metamorphic assemblage further into the footwall.

Jan 1, 2002

By K. Twite, K. Mujinga, J-M. Dereydt, P. Louis

"GECAMINES is a large mining concern and the world's leading cobalt producer having some of the richest cobalt deposits in the world. Cobalt is associated in the ore with copper as sulphides and oxides and in some locations with nickel too. Specific hydrometallurgical processes have been developed by GECAMINES which had done an important contribution to the development of the cobalt hydrometallurgy.In the Shituru plant, cobalt is obtained from an unique in-pulp electrolysis process, while in Lullu, cobalt is electrolyzed in a clear acidic solution giving a purer deposit. In the beginning of 1996 Shituru started the treatment of mixed Cu-Co-Ni Shinkolobwe hydrates obtained as by-product of an uranium solvent extraction plant. A typical analysis of this feedstock is: 2% Cu, 8% Co and 4% Ni.The nickel sulfide depolarized cementation process developed previously by GECAMINES was inefficient to treat such a high level of nickel contamination and it was decided to produce alloyed Cobalt-Nickel cathodes in the Shituru tankhouse.As anticipated from laboratory tests as previous studies and publications, a lower Ni/Co in the deposit was obtained compared to the Ni/Co ratio solution, despite the nickel reversible electrochemical potential is somewhat higher than the one of cobalt (-0.25 V vs -0.28 V).In this paper, the process flow-sheet and production data are given. Cobalt alloy with 5 - 20 % Ni was obtained at a production level of 300 t per month. The process developed is a new contribution to cobalt hydrometallurgy."

Jan 1, 1997

By Jorge A. S. Tenorio, Chuanwei Zhuo, Joner O. Alves, Yiannis A. Levendis

"Reduction of combustion-emitted greenhouse gases, which are associated with global warming, may be achieved by use of CO2-neutral alternative fuels, such as bio-ethanol. Distillers Dried Grains with Solubles (DDGS) are the main co-products of the com-grain-based ethanol industries. In 2009, the North American production of ethanol from com was about 38 billion liters, which generated approximately 31.5 million tons of DDGS. Samples of DDGS were pyrolysed at temperatures of 600-1000 °C in a two-stage laminar-flow horizontal furnace, and a catalyst system was used to synthesize nanomaterials. This work presents a microstructural characterization of these nanomaterials by scanning electron microscopy (SEM) and transmission electron microscopy (TEM). Results showed that the nanomaterials produced from pyrolysis of DDGS were in the form of long, entangled, rope-like structures with rugged walls, lengths in the tens of microns, and axially non-uniform diameters in the range of 100-300 nm.IntroductionThe interest in ethanol has increased considerably worldwide due to the necessity of finding renewable and cleaner energy resources [1, 2]. According to the Renewable Fuels Association (RF A), the world ethanol production in 2008 was approximately 65.7 billion liters (17.3 billion gallons), which figure represented a 24% increase in the production over that in the previous year [3]. The major producers of ethanol are the USA and Brazil, which together account for 90% of world production. The main feedstock for ethanol in USA is com grain, whereas sugarcane predominates in Brazil [2-4]."

Jan 1, 2011

By Jan E. Nesset, Phillip J. Mackey

"Studies have shown that there is a correlation between commissioning and start-up time, i.e. time to reach full plant design capacity, and the degree of innovation and technical/engineering uncertainty in the project design. The paper describes the types of start-up curves for plants according to the level of technology or uncertainty in the process design. The need to properly describe and understand the commissioning and start-up time is examined using these curves and the importance on project success is highlighted. A number of case histories of recent mining and metallurgical projects are also reviewed. Finally, the paper reviews how to better assess the level of start-up uncertainty associated with a project and makes suggestions for decreasing the commissioning time due to technological risk.INTRODUCTIOThe start-up of a new mining and metallurgical facility, a much anticipated event, is a critical step in the life of such a project. Achieving a successful start-up and reaching the design capacity on-time requires careful planning, a thorough understanding of the key technological and engineering components involved and a well-trained and adequatelystaffed start-up crew. In this paper, some of the aspects related to start-up of a mining/metallurgical project will be explored, and in particular, the impact of the technology component will be examined. In order to illustrate this, a number of case histories based on recent mining and metallurgical projects will be discussed. Ways of assessing and understanding the uncertainty associated with technological issues related to start-up of a mining and metallurgical plant will also be examined.The history on mining and metallurgy is full of success stories of great mines and mills that are now considered “company makers” (well known examples of such successes include the Horne mine for Noranda which had a 1 year start-up in 1926-27, the Dome mine for Placer Dome, the Grasberg deposit for FMI in Indonesia). Less well documented are specific studies relating to plant start-ups and what constitutes a success or a failure, however there are a few notable references in the literature and these will be reviewed."

Jan 1, 2003

By R. L. Armstrong, C. I. Godwin, V. M. Kruan

"The Scheelite Dome tungsten-bearing skarn property, central Yukon Territory, is in metasediments in contact with a quartz monzonite intrusion. Contact metamorphism to biotite-muscovite- andalusite hornfels and calc-silicate hornfels is superimposed on low-grade regionally metamorphosed rocks represented by quartz-mica pelitic schist and muscovite-biotite pelitic schist.Metasediments are likely Precambrian in age, even though Rb-Sr whole-rock analyses indicate an early Paleozoic age (511±41 Ma); this apparently too young radiometric age is due to partial loss of radiogenic strontium during regional metamorphism. The minimum age of the quartz monzonite intrusion is Cretaceous at 90.4±2.6 Ma (K-Ar on biotite) and its initial 87Sr/86Sr ratio is 0.7121. The high initial ratio of the intrusion is due to the addition of radiogenic strontium from the metasedimentary country rocks and perhaps an underlying older basement.Scheelite-pyrrhotite-chalcopyrite mineralization occurs in diopside-zoisite skarn pods within the calc-silicate hornfels near the quartz monzonite intrusion. The source for lithophile tungsten is probably the same as for the granitic magma, namely Precambrian sialic basement.IntroductionThe Scheelite Dome tungsten skarn property is within the Mc-Questen map-area (NTS: 115P/16),28 km northwest of Mayo, Y.T., at latitude 63°47' north and longitude 136°15' west. The property can be reached by helicopter or by four-wheel- drive vehicle from Mayo.This paper summarizes the geology of the Scheelite Dome property, which has been described in a general way by Little (1959) and Cathro (1969). Geological mapping and sampling were done by the first author (nee Steffler) during June 1979. Field work was supplemented with detailed work at the Department of Geological Sciences of The University of British Columbia during 1979 and 1980 (Steffler, 1980). Whole-rock chemical analyses were done by Cominco Ltd."

Jan 1, 1982

By T Sirinawin, R H. Murfitt, W Shywolup

The Bong Mieu Project lies within the Pre-Palaeozoic Kontum Craton near the southern margin of the regional Phuoc Son û Tam Ky Suture. The Suture and accompanying Truongson Fold Belt of Indosinian age host significant gold and base-metal bearing districts including OlympusÆ other project at Phuoc Son to the west of Bong Mieu and OxianaÆs Sepon project in Laos. The Bong Mieu Project is located some 90 km south of Da Nang and some 30 km south-west of Tam Ky, the provincial capital of Quang Nam province in central Vietnam. The project area is covered by an Investment Licence of some 30 km2 which was granted in 1991 and a mining permit of some 365 ha granted in 1992. Several mesothermal, gold-silver deposits with assigned resources are present on the property. Deposits with assigned resources contain some 615 000 ounces of gold in situ. These are at Ho Gan and Ho Ray which are potentially exploitable by open-pit mining and Nui Kem which is potentially exploitable by underground mining. Newly discovered extensions to the known deposits at Ho Gan, Ho Ray and Nui Kem, and several other new prospects, are currently being investigated by drilling. The Ho Gan mineralisation is of mesothermal, shear and shear breccia quartz vein, as well as intrusive breccia hosted style. Nui Kem mineralisation is of mesothermal, shear and shear breccia quartz vein style. The Ho Ray mineralisation is of skarn (gold-bismuth-tungsten) and lesser quartz vein style. The deposits straddle and flank the east-west trending Bong Mieu Anticline which trends through the central portion of the Investment Licence. In this paper the geology of the deposits, details of resources, results of recent exploration on the Investment Licence and recent engineering and mining studies at Ho Gan are briefly reviewed.

Jan 1, 2004

By B. Amero, W. Petruk, D. R. Owens, D. R. Morris

Samples taken at different heights in the lead blast furnace of Brunswick Mining and Smelting corporation were studied to determine the phases present in order to interpret the reactions In the furnace. The main phases in the blast furnace feed are Pb3Ca2S13011, Zn ferrite (ZnFe204), and hardystonite (Ca2ZnSi207); rninor ones include lead and a Pb silicate. The temperature in the furnace varies from about 300°C at 4.2 m above the tuyeres to 1150°C at 1.1 m. There is no evidence of reactions in samples from points cooler than 800°C. Some reaction occurs between 950° and llOO°C and the lead sinter is nearly decomposed at about 1150°C. The first evidence of reaction was the decomposition of Pb silicate to lead and S102. At higher temperatures the Pb Ca2Si3011 decomposed to form lead and hardystonite (Ca2ZnS120rf. The Zn required for hardystonite was derived from the Zn ferrite which apparently re-equilibrated to a new Zn ferrite with less Zn. The decomposed sinter consists essentially of lead, hardystonite, wustite and a Zn ferrite with a low Zn content.

Jan 1, 1984

By Forsythe DJ, Sun S-S Andrew AS

Paragenetic, fluid inclusion, stable isotope, and 87Sr/86Sr and 143Nd/144Nd isotope studies of the Mt Carbine tungsten deposit in North Queensland provide information on the sources of the mineralising components and record the history of fluid-rock interaction during the hydrothermal process. The ore minerals , wolframite and scheelite , are contained in quartz veins which post-date the major deformations in the Siluro-Devonian Hodgkinson Formation . Mineralisation was immediately preceded by the emplacement of the Mossman Batholith (280 ¦ 7 Ma). Two major stages of mineralisation are present and separated by a brittle fracturing episode . The stable isotope and Sr and Nd isotope data suggest that the ore fluids during stage I and most of stage II mineralisation were a mixture of magmatic water and non-magmatic water (connate or metamorphic) which had experienced a long residence time and had extensively exchanged with the sediments at high temperature. Subsequent mineralisation events were dominated by fluids of meteoric derivation with a short residence time. The data imply that other solutes, such as W, were probably derived in minor part from local country rock sources with the major contribution coming from a magmatic source related to the granite batholith.

Jan 1, 1987

By P. Somasundaran

Almost a decade has elapsed since the problem of fine particles processing was first discussed at the National Science Foundation workshop in Arden House (Somasundaran and Fuerstenau, 1976). Problems involved in processing fines are as enormous now as they were then. We still lose 20 to 50% of mineral values during the processing of many ores. While the problem's magnitude has remained at as high a level as ever, our perspective on the causes for the difficulties, I believe, has changed. While we do not yet see any grand unified solution to all the problems in this area, I do feel that we are beginning to get an understanding of the basic reasons for the behavior of fines. I would like to share my views on the fundamental reasons for the problems we face. They are based essentially on results obtained during the last few years. A decade ago, I presented the reasons shown in the [Fig. 1] as the causes for the difficulties in separating fines. We have seen the same type of information discussed by others during the years since then. I now believe that these are not the only primary causes. Indeed, they do contribute, but there are other major reasons we ought to recognize. Mass certainly would have its effect, but since microorganisms and even ions can be separated from each other using flotation, provided correct conditions are used. I do not believe that fines 10,000 times bigger suffer fundamentally from their smallness or lightness. Similarly, the surface energy increase cannot be as important a fundamental factor since, theoretically, we should not see significant changes in surface energy until we get down to particles a hundred times finer than we are concerned with. Increase in surface areas, again, cannot be a primary problem except for an increase in reagent consumption. What possibly could be the reasons? I have added these three items to the list in [Fig. 1]: morphology, mineralogy, and surface chemical composition. Differences that I believe are partly responsible for the behavior of mineral fines are those due to alterations in morphology or mineralogy and surface chemical composition with decrease in size.

Jan 1, 1985

By A. Sargeant

This paper evaluates the application of post consumer glass as a cementing agent in underground mine backfills. The underlying theory indicates that glass is pozzolanic and, when used in a finely divided form, behaves as an activator to generate binding products, thus contributing to the development of backfill strength. The objective of this study was to evaluate the strength performance of backfills when Normal Portland Cement is replaced with various percentages of post consumer glass. The study evaluated the performance of backfills prepared using tailings from three mines. Each backfill was prepared using unique recipes, and were evaluated at cure times of 7, 14, 28, 56, 112 and 224 days. Laboratory work involved visual, physical and chemical material characterization followed by strength evaluations. Results of strength assessment revealed that backfill prepared with glass is reactive and can contribute to the strength of backfill. The results also indicated that the reactivity of glass may be affected by the incorporation of slag within the recipe, the availability of lime and the level of hydration of the binders. The study concluded that, at 15 % glass replacement of NPC, backfill prepared with mine tailings, NPC and glass can achieve improved or equivalent strength performance compared to backfill prepared tailings and NPC alone.

May 1, 2007

By Kourosh Shahriar, Kazem Oraee, Ezzeddin Bakhtavar

"In this paper, a relationship between dependant parameters and the crown pillar thickness is first introduced. This relationship defines geotechnical problems caused by thin pillars and economic considerations created by pillars that are thicker than the optimum size. For this purpose, a dimensional analysis as an effective physico-mathematical tool was used. This technique restructures the original dimensional variables of a problem into a set of dimensionless products using the constraints imposed upon them by their dimensions. A model is hence introduced that calculates the optimum pillar thickness. The relationship introduced here and the method applied can be used by mining engineers in all situations where a combined open-pit and block caving method is deemed to be the most appropriate mining method.INTRODUCTIONMany deposits can be mined entirely with the open-pit method; others must be worked underground from the very beginning. In addition, there are the near-surface deposits with considerable vertical extent. Although they are initially exploited by the open pit method, there is often a ""transition depth"" where decision has to be made about changing to underground methods.Some of the biggest open-pit mines worldwide will reach their final pit limits in the next 10 to 15 years. Furthermore, there are many mines planning to change from open-pit to underground mining due to increasing extraction depths and environmental requirements. In this way, it is likely that block and/or panel caving will enable the operations to continue achieving a high production rate at low costs as an underground method (Bakhtavar et al., 2009).In these cases, it is often necessary to consider a crown pillar beneath the transition depth (open-pit floor) before starting an underground caving stope method (Figure 1).There are generally two kinds of crown pillar: a ""surface crown pillar"" and ""crown pillar between open-pit and underground mining."" In general, they both play the similar role in mining. Since the primary purpose of a surface crown pillar is to protect surface land users, the mine, and those working in it from inflows of water, soil, and rock; it is vital that the surface crown pillars remain stable throughout their life. When a crown pillar could potentially remain between open-pit and underground mining it is specially proposed to prevent water entering from the open-pit floor into the stope, as well as to reduce open-pit wall and floor caving."

Jan 1, 2010

By H. Hansen, A. U. Seybolt, P. Yurcisin, B. W. Roberts

The Bi-Mn phase diagram in the region near BiMn was investigated, using principally thermal analysis and changes in magnetization with temperature. Of chief interest are the findings related to the magnetic transformation in Bi-Mn. THE Bi-Mn system is of both theoretical and practical interest because of the occurrence of the compound BiMn which exhibits unusual ferromagnetic properties. Because the Bi-Mn phase diagram reviewed by Hansen' (see Fig. 1) in 1936 is based on work done by BekierY in 1914 and by Siebe" in 1919, which left considerable doubt about the nature of the diagram. it appeared desirable as an aid in understanding the alloying characteristics and magnetic behavior to examine the pertinent regions of the phase diagram. The most interesting reaction is the peritectic at 445°C which forms BiMn by the reaction: Liquid + Mn(sulfield) ? BiMn(sol field) There is also a eutectic at 262° C between pure bismuth and BiMn. Hansen draws in BiMn dotted, since in 1936 evidence for its existence was uncertain. Experimental Materials—Preparation of Alloys Electrolytic manganese of about 99.97 pet purity and bismuth of 99.99 + pet purity were used as starting materials.

Jan 1, 1957

By C. John Dunnicliff, Birger Schmidt

INTRODUCTION To be effective and useful, monitoring of tunnel construction must be carefully planned throughout all steps. A vital and frequently overlooked step is a clear definition of the specific purposes of the instrumentation. Most tunnel construction monitoring has in the past been of benefit to research, the advancement of tunneling practice, wittingly or not. The development of monitoring instrumentation for the benefit of the project from which the data are recovered has very significant potential for risk and cost reduction of soft ground tunneling. A systematic approach to tunnel construction monitoring, from conception to full implementation, includes at least the following nine tasks or steps: Definition of benefits and purposes; design and project specification to draw full benefits; selection of monitoring parameters; selection of instruments and writing of specifications for procurement and installation; procurement and installation; reading and maintenance; data storage and retrieval; interpretation; implementation. Some of these steps are fairly easy and resolved through the use of established theories and technologies. The difficult ones are those that require the bending of minds, those that involve changes in the ways engineers design soft ground tunnels, the way owners pay for tunnels, and the construction is managed, inspected and controlled. Performance monitoring can be of benefit to the owner, design

Jan 1, 1974

By Gerhard Lang

"Slurry Microtunneling is a well-established technology building on over 20 years of experience in successful tunnel installations under all kinds of soil conditions across the U.S. and Canada. Recent microtunnel installations prove that initial hesitation, e.g. curved drives, is fading and long-distance pipe jacking projects as well as lake outfalls are being considered. One of the younger technologies is Direct Pipe®, which combines the benefits of HDD and Slurry Microtunneling. It fits exactly into the area where HDD is not feasible or too risky to apply. The paper points out the benefits of the Direct Pipe® technology for owners, engineers and contractors and discusses the latest developments of Slurry Microtunneling for long-distance, curved drives and sea/lake outfalls with wet recovery of the equipment such as on the ‘Keswick Outfall Project’ in Ontario. The first Direct Pipe® installation in the US was executed in August 2010. Since then, another 22 crossings have been carried out amongst a total of more than 60 Direct Pipe® crossings worldwide. INTRODUCTION Pipelines installed underground are indispensable for supplying the growing world population with water, oil, gas and electricity, for removing wastewater and for providing functioning telephone and communications networks. During recent years the limits of trenchless applications have been permanently shifted, leading to higher and more stringent project requirements and consequently new technologies, either as further development of existing methods, or through the development of new methods by incorporating elements of proven technologies. MICROTUNNELING TRENDS IN NORTH AMERICA Slurry Microtunneling has a wider geological application range in comparison to EPB and hard rock Microtunneling. The Slurry MTBM can be equipped with specific cutting wheels to cope with different soil conditions. The most flexible and most often employed type is the mixed soil cutting wheel, which contains a mixture of disc cutters as well as scrapers for varying soil conditions from cohesive soils (clay, silts) to highly permeable soils including sands, gravels and cobbles and even hard ground formations such as rock and boulders. A detailed geotechnical report provides the appropriate data to configure the MTBM and its features to the ground conditions expected. Mixshield or hydroshield (AVN/AVND) MTBMs in particular, can be safely operated with little overburden (~ 3-5 x machine diameter) and minimum risk of frac-out or settlement on the surface. This is especially beneficial in urban areas with sensitive buildings or for river crossings with protected fish habitats."

Jan 1, 2016

By O. Martinsson

The Kiruna area is an important mining province in northern Sweden, which is dominated by Fe- and Cu-Au deposits. Economically most important for the region, are the apatite iron ores with an annual production of c. 43 M ton of crude Fe-ore and a total production of more than 2000 M ton of ore the last 100 years. The apatite iron ores in the Kiruna area are dominated by either Magnetite or Haematite and contain varying amounts of apatite giving them a content of Fe and P, which varies between 30-70 % and 0.05-5 %, respectively. A typical geochemical feature of the ores is the strong enrichment of REE that is caused by a high content of REE in apatite and the occurrence of Allanite and Monazite containing 22.4 and 69.8 wt% REO, respectively. At Kiirunavaara, the content of REE in apatite varies between 0.07 to 1.57 wt% REO with a dominance for the light rare earths. The variation in REE-content of apatite depending on textural and paragenetic aspects is not known but apatite grains may display a strong LREE-depletion due to hydrothermal alteration. Monazite occurs as rod-shaped or tabular inclusions in apatite and is suggested, to have formed in response to hydrothermal alteration of apatite after the emplacement of the ore. Inclusions are mainly found in the central part of apatite grains occurring in veins and schliren, while they are rare in apatite occurring disseminated in the ore. Monazite also occurs as larger grains outside apatite and together with Allanite is found in texturally and paragenetically different settings within the ore. These occurrences of REE-minerals may largely be a product of LREE mobilized by alteration of apatite after the emplacement of the ore. However, REE-minerals including Allanite and Monazite might also have formed directly from late magmatic fluids. Keywords: apatite, monazite, allanite, ree, kiirunavaara, iron ore of kiruna type, mineral chemistry

Sep 1, 2012

By N. Edmonson

An examination of the statistics of the world phosphate fertilizer industry since 1980 reveals an increasing tendency for fertilizer manufacturing activity to concentrate in phosphate rock mining areas. The economic justification for this resource-oriented strategy is clear. The choice between shipping phosphate rock, a comparatively low-value product, and shipping more valuable finished fertilizers will always be resolved in favor of the latter if cost considerations control the decision. The historical existence of substantial phosphate fertilizer manufacturing capacity oriented toward fertilizer-consuming activities and dependent on imported phosphate rock shows that narrow cost considerations have not always determined the industry's location. One is entitled to ask what conditions have changed to precipitate the observed relocations, and how permanent these changes are. These questions are the subject of this investigation.

Jan 1, 1995

By E. L. Montgomery

Salar basins in the Andean Highlands of Northern Chile contain ground-water resources which could be used to satisfy requirements for the mineral industry in the region. Salars occur in arid zones; average precipitation is about 200 millimeters per year at altitudes of about 4,000 meters, and average annual evaporation is two meters or more. The salar basins are hydrogeologic sinks where water flows from recharge areas at the margins of the basins to discharge areas at the salt encrusted salar at the lowest point of the basin floor. Groundwater circulation occurs principally in the alluvial and fractured bedrock aquifers. Results of pumping tests for exploration and production water wells indicate a range in maximum sustained pumping yield of 62 to 126 liters per second, and where abundantly fractured, ignimbrite comprises the most prolific aquifer. Chemical quality of groundwater is good. Long-term pumping from properly located production wells in the salar basins would result in lowering of groundwater levels and salvage of water in areas where groundwater is lost via evaporation.

Jan 1, 1986