Search Documents

By G. L. Oldright

The data in this paper were collected at the Trail smelter of the Consolidated Mining & Smelting Co. of Canada, Limited, through the courtesy of S. G. Blaylock, vice president and general manager; James Buchanan, smelter superintendent; George Murray, assistant smelter superintendent; and the staff members given in Paper XI, Report of Investigations 3243. INTRODUCTION This paper is the thirteenth of the series on Smelting in the Lead Blast Furnace, and the third of the series on Handling Zinciferous Charges. Tyro other papers have been written on the Rate of Descent of the Stock Column, and Formation of Accretions. These are Reports of Investigations 2963 and 3094, for the Tooele plant and the Bunker Hill plant, respectively.

Jan 1, 1934

By D. A. Dahlstrom

In the paper, a comparison was made between flowsheets using the screen bowl centrifuge and disc filters, respectively, as the primary dewatering device. The authors very effectively show that by raising feed temperature, mechanical dewatering is enhanced through reduced viscosity of the water. When a final coal moisture of 10% is required, the net effect of heating the feed is a reduction in thermal requirements because of the lower evaporated load on the dryer. The flowsheet comparison on this, however, was not completely correct. Disc filters do not generally utilize enhanced mechanical dewatering through increased temperature. Horizontal belt filters, through the optimal use of steam heating of the filter cake, have shown significant cost reductions over disc filters where steam is not used. In addition, the authors forgot to mention that there is a certain fraction of the feed that is so fine that it cannot be recovered by the centrifuge economically. That is the function of the filtration device shown in [Fig. 4]. In subbituminous pipeline coals, this fraction represents more than 10% of the feed. Even after flocculation and belt pressing, the moisture content in the fine fraction is 30%-40. Recent tests on a subbituminous pipeline coal slurry, compared an Eimco-Extractor horizontal belt filter with the screen bowl centrifuge flowsheet shown in [Fig. 4]. Mechanical dewatering was enhanced through the use of a steam dry zone after the initial dewatering zone. Vacuum pump horsepower was reduced by more than 50% through the use of condensers, and heat recovery was utilized to minimize thermal costs. Thermal drying to 10% moisture by weight was required in both flowsheets. The 0.5 wt% fines in the filtrate were flocculated and recycled to the filter, thus eliminating the belt press and solids mixers. When the three major operating costs (which normally account for 50%-75% of the coal operating costs) of steam, electricity, and flocculants at current prices were calculated, the flowsheets utilizing the Eimco-Extractor had cost savings vs the centrifuge flowsheet of 89c/t (81c per st) of surface dry coal. This advantage increases with increasing thermal and electricity prices. I congratulate the authors for the strides made with the screen bowl centrifuge. However, filtration flowsheets continue to be improved and their simplicity and low thermal and electrical requirements should not be so quickly dismissed.

Jan 1, 1984

By E. R. Parker, D. L. Martin

In a previous paper one of the authors observed that the rate of cooling from the anneal prior to testing greatly influenced the life of copper under sustained load at 200°C. Furnace-cooled bars of oxygen-free copper (with and without silver) had a life four to twenty-five times that of the water-quenched specimens. The addition of 0.054 per cent silver to the oxygen-free copper increased the life at a stress of 20,000 lb. per sq. in. from about 2 hr. to 50 hr. Fractures in these bars were intercrystalline. An explanation was advanced to account for the profound influence of cooling rate on the rupture properties at 200°C. The suggestion offered was that at the high annealing temperature the minor constituents are distributed at random. By water quenching, this condition is maintained at room temperature, whereas furnace cooling permits some segregation at the grain boundaries. The higher concentration of the minor constituents in the grain boundaries results in a. strengthening, so that a longer life at a given stress and .temperature results. Small amounts of cadmium or manganese have also been found to increase the life of copper at 200°C., and to a much greater extent than silver.2 The increase in the long-time strength of copper resulting from small additions of cadmium or silver appears to be related, indirectly at least, to the higher softening temperatures of such alloys. The elements, such as silver or cadmium, which greatly increase the rupture life of copper also cause large increases in the softening temperature. As little as 0.05 per cent of cadmium or silver is sufficient to raise the softening temperature more than 100°.3,4 The effects of cooling rate and of minor constituents on the rupture properties are of considerable fundamental as well as practical interest; therefore a more detailed study of their nature was conducted and is reported in this paper. Experimental Procedure Materials The materials studied in this investigation may conveniently be classified in two groups: one consisting of a wide variety of commercial coppers, and the other composed of special high-purity, laboratory-prepared coppers. The commercial materials were tested to determine whether or not the effect of cooling rate occurred with all coppers, whereas the high-purity coppers were investigated in order to establish a basis for evaluating the effect of minor constituents on the rupture properties. In Table I are given the analyses of the coppers tested. The samples I to 6 are commercial materials and were obtained for the most part from stock supplies.*

Jan 1, 1944

By D. L. Martin, E. R. Parker

In a previous paper one of the authors observed that the rate of cooling from the anneal prior to testing greatly influenced the life of copper under sustained load at 200°C. Furnace-cooled bars of oxygen-free copper (with and without silver) had a life four to twenty-five times that of the water-quenched specimens. The addition of 0.054 per cent silver to the oxygen-free copper increased the life at a stress of 20,000 lb. per sq. in. from about 2 hr. to 50 hr. Fractures in these bars were intercrystalline. An explanation was advanced to account for the profound influence of cooling rate on the rupture properties at 200°C. The suggestion offered was that at the high annealing temperature the minor constituents are distributed at random. By water quenching, this condition is maintained at room temperature, whereas furnace cooling permits some segregation at the grain boundaries. The higher concentration of the minor constituents in the grain boundaries results in a. strengthening, so that a longer life at a given stress and .temperature results. Small amounts of cadmium or manganese have also been found to increase the life of copper at 200°C., and to a much greater extent than silver.2 The increase in the long-time strength of copper resulting from small additions of cadmium or silver appears to be related, indirectly at least, to the higher softening temperatures of such alloys. The elements, such as silver or cadmium, which greatly increase the rupture life of copper also cause large increases in the softening temperature. As little as 0.05 per cent of cadmium or silver is sufficient to raise the softening temperature more than 100°.3,4 The effects of cooling rate and of minor constituents on the rupture properties are of considerable fundamental as well as practical interest; therefore a more detailed study of their nature was conducted and is reported in this paper. Experimental Procedure Materials The materials studied in this investigation may conveniently be classified in two groups: one consisting of a wide variety of commercial coppers, and the other composed of special high-purity, laboratory-prepared coppers. The commercial materials were tested to determine whether or not the effect of cooling rate occurred with all coppers, whereas the high-purity coppers were investigated in order to establish a basis for evaluating the effect of minor constituents on the rupture properties. In Table I are given the analyses of the coppers tested. The samples I to 6 are commercial materials and were obtained for the most part from stock supplies.*

Jan 1, 1944

By C. Y. Chen

In order to put an end to the uneven environmental standards and enforcement established by various coal mining States in the United States, the Congress passed and the President signed the Surface Mining Control and Reclamation Act (Public Law 95-87 or the Act) on August 3, 1977. Within one year after passage, the Secretary of the Interior was directed to promulgate permanent program regulations implementing Title V provisions of the Act. These regulations were to form the basis for State regulatory programs under the Act and to allow States to assume primary regulatory responsibility. In order to implement the underground mining provision of the Act, the Secretary is directed in section 516(a) of the Act to promulgate rules, but ones which take into consideration the distinct differences between surface coal mining and underground coal mining. The regulations developed by the Secretary and promulgated on March 13, 1979, with respect to subsidence control, included (1) a subsidence control plan as part of the permitting process, (2) substantive provisions establishing performance standards for subsidence control, and (3) provisions providing for the prohibition of mining under perennial streams, impoundments larger than 20 acre feet, and certain public facilities and urban areas.

Jan 1, 1985

By Z. Bibak, S. Banisi, A. Ghasemi, E. Nematollahi

"The major importance of liners in grinding is their role in providing an appropriate trajectory for the charge. Since it is not possible to study the charge movement by direct observation in operating industrial mills, this task is accomplished by physical (laboratory), and/or, mathematical (software) methods. Because of the high cost and a longer time required for a physical analysis, mathematical simulations have become more common. Simulation of the effect of liner shape on the charge movement has provided a means to select a proper design based on the operational objectives and conditions. Furthermore, the liner shape changes due to wear and impact during operation, which will influence the charge trajectory. This adds more of an incentive to use simulation. These changes in liner could be predicted through liner profile measurements during operation and/or simulation. In this research, an inhouse developed DEM software called KMPCDEM © was used to simulate the charge movement in industrial plant SAG mills. A geometrical method of implementing the shell liners on SAG mills at the Sarcheshmeh (9.75×4.87 m) and the Gole-E-Ghohar (9×2.05 m) operations facilitated the software simulation. Point by point implementation of the measurements of liner profiles of these mills enabled the study to trend the change in the charge movement as the liners wear. Comparison of the simulation to a laboratory mill (1 m diameter) showed that the difference between the measured and predicted charge impact point, shoulder angle and toe angle were 6, 4 and 3°, respectively.INTRODUCTIONComminution is the most energy intensive operation constituting the major portion of operating and capital costs of a mineral processing plant. In the last decade, a vast number of research was aimed at studying various aspects of grinding with the aim of performance improvements (Davis, 1919; Mishra & Rajamani, 1990; kalala, Breetzke, & Moys, 2008). Mill liners transfer the input power to the charge and play a significant role in affecting the motion of the charge (Mclvor, 1983; Mishra & Rajamani, 1990; Radziszewski, 1997; Van Nierop, Glover, Hinde, & Moys, 2001; kalala et al., 2008). Lifters are usually used with mill liners to extend their life and to enhance the grinding and impact breakage efficiency. Mill lifters are used to raise the grinding media and ore to transfer the energy from the mill to the load (Rezaeizadeh, Fooladi, Powell, & Weerasekara, 2010)."

Jan 1, 2016

By Earl C. Redman

The Juneau Gold Belt, centered on Juneau and approximately 120 miles long by 10 miles wide, stretches from Berners Bay on the north to Windham Bay on the south (fig. D-l). Access within the Juneau Gold Belt is provided by the Glacier, Thane, and North Douglas Highways. The Glacier Highway extends northwest from Juneau for approximately 40 miles to Echo Cove, and the other two roads end 5.5 miles southeast and 12.6 miles west from Juneau, respectively. None of these roads connect with other highway systems and access to other areas is restricted to airplanes, the State ferry system, and commercial barge lines. BUREAU ACTIVITIES The majority of lode gold produced in Alaska came from the Juneau Gold Belt portion of the Juneau Mining District. To evaluate the economic potential of the Gold Belt, the Bureau located 173 mines and prospects within the area. A total of 263 ad its and shafts were found and 56,650 feet of underground workings were mapped. The Bureau collected and analyzed 1,557 samples during the study. In addition, considerable detailed geologic map-ping was done in the vicinity of the mines and prospects from which ore control models were developed.

Jan 1, 2012

By S. W. Marcuson, P. J. Mackey

The Canadian non-ferrous mining and metallurgical industry has made great strides in environmental protection during the past half century. The path taken by the copper-nickel smelting industry in reaching today’s level is traced in this paper. Following the practice at early copper smelters in Wales and in the US, Canadian smelters originally used tall stacks to disperse furnace of-gases. This was the normal mode of operation and was accepted by society and by Government. Gradually, Government regulations required fixation of sulphur dioxide emissions and Canadian companies responded with significant technical developments to achieve this result. The initial development in Canada of the first new technologies such as the Cominco Flash Suspension Roaster and the Freeman Flash Smelting Process - both representing early versions of the modern established flash smelting technologies - and then later technologies such as the Inco Flash Smelting Process and the Noranda Process, both of which continue to this day, are discussed in this paper in terms of their contributions to the development of environmentally friendly plants. The evolution of these and other technologies is also discussed. Some comments regarding how the industry will face the future are also included.

Jan 1, 2015

By Ian W. Wark, Keith L. Sutherland

IT has been shown' that in the absence of heavy metal salts, the nature of the alkali used to promote differential flotation-whether caustic soda, lime or sodium carbonate-is unimportant. The hydroxyl ion is the active depressant upon which differentiation depends, and the pH value determines whether a film of collector forms on any given mineral surface. Even when sodium cyanide is used in conjunction with alkalies, it is the pH value and not the nature of the alkali or its concentration that is important, for upon the pH value alone depends the fraction of the added sodium cyanide that is present as cyanide ion, which is the true depressant. When heavy metal salts become dissolved from partly oxidized ores, or are added intentionally as activators, conditions are different, and metallurgists have found that lime and sodium carbonate do not give identical results, even when added in amounts sufficient to produce the same pH value. In the few instances in which we had attempted to confirm this view, we had failed to do so, for, with nothing to guide us, we had inadvertently chosen solutions that gave contact curves of a "standard type," which correspond to conditions of ready floatability. Now, however, we find that, in the presence of copper salts, and within a restricted range of reagent concentrations, the nature of the anions present is important, and that sodium carbonate does influence the results, apart from the usual effect due to its influence on pH value. With the recognition of this anion effect, and with the control of temperature already introduced,2 it appears that the factors of major importance in connection with this set of reagents have been taken into consideration, and that the results obtained and the conclusions drawn from contact tests will be of more immediate value to the operator. It is not difficult to suggest an explanation for the influence of the carbonate ion in the presence of copper sulphate. The works of Picker-

Jan 1, 1939

By Karl Oltay

A series of 15, stations beginning with Potsdam and Budapest and ending with Budapest and Potsdam were occupied inn the period August, 1908, to January, 1909. The intermediate stations were all at points which had been connected by Baron Eötvös with torsion-balance traverses. The observations were made with an invariable pendulum of the standard four-pendulum type of instrument of the Geodetic Institute, made by Stückrath at Berlin-Friedenau. The observations at each of the field stations lasted-one to three days with one exception; two or three time determinations were made; four to eight series of pendulum observations were made; the error of determination of the elevation of the instrument above mean sea level ranged from 0.30 meter to 1.10 meters, with the exception of the Arad and Baja stations, where the elevation was known more accurately and averaged about ± 0.8 m, which would cause an error of ± 0.25 x 10-3 dynes. No topographic correction was applied. The values for ?g were taken from Eötvös: Report on Geodetic Observations in Hungary, especially Observations with the Torsion Balance, Budapest, 1910. The differences in ?g as determined, by the torsion balance and by the unvariable pendulum were: Kuvin-Hidegkut 1.2 km. 0.001, Livada-Kuvin 9 km. 0.001, Pankota-Livada 13 km. 0.004, Kuvin-Arad 20 km. 0.000, Pankota-Arad via Kuvin 42 42 km.0.005, Pankota- Arad via Kurtics 50 km.0.000 dynes. Oltay concludes that if the stations are close enough together and if the terrane is rather flat, the measurement of ?g with the Eötvös torsion balance is as accurate as with the invariable pendulum. -- Donald C. Barton.

Jan 1, 1929

By Robert Hopler

THE work that is being done by the Government to reduce the dangers of mining was brought out strikingly in the First National Mine-Safety Demonstration which occurred at Pittsburgh, Pa., on October 30th and 31st, under the auspices of the United States Bureau of Mines with the assistance of the American National Red Cross Society and the Pittsburgh Coal Operators’ Association.

Jan 1, 2012

By I. R. Kramer, P. D. Gorsuch, D. L. Newhouse

Although many methods have been suggested for the calculation of tensile strength and yield point from chemical composition, their usefulness has been limited to a particular cooling rate or section size. Further limitations have been imposed by failure to take into account many of the alloying elements that exert a considerable influence on the tensile strength or yield point. These systems, nevertheless, have filled an important need in many instances. The value of a system for the calculation of the tensile properties from the chemical composition and cooling rate is that it permits the prediction of the effect of alloying elements and heat-treatment on the mechanical properties, so that more efficient use of alloying elements may be made. Furthermore, it aids in the choice of steel for a given application aid tends to decrease the number of steels that otherwise would have to be tested. It is the purpose of this work to present a method of calculating tensile strength and yield point from the chemical composition and to suggest a method of correlating the tensile-strength and yield-point factors and cooling rate. Steelmakers have been interested for many years in the calculation of the tensile strength of hot-rolled steels. Quest and Washburn' summarize several of the attempts that have been made to devise formulas. They show the inadequacy of each of these formulas and present one of their own. It is apparent from their work that a simple additive equation of the type TS = A + BX + Cy + DZ + . . . , where A, B, C, D, etc. are experimentally determined constants and x, y, z, etc., are the percentages of alloying elements present in the steel, is not adequate to analyze fully the situation encountered in the calculation of tensile strength. For example, it was found that the difference between the calculated and observed values became progressively greater as the carbon and manganese contents were increased. Therefore, the effect of manganese was given as a function of the carbon content. Grossmann, in his work on the harden-ability of quenched steels, and Walter, in his method of calculation of tensile strength of normalized steels, present two cases in which multiplying factors were successfully used to express the combined effect of alloying elements. The factors in both cases were obtained from the fractional increase in hardenability or tensile strength with increase of alloy content. Yield point often is more important in design than tensile strength. For quenched and tempered steels a linear correlation exists between yield 2nd tensile strength.4 This is not true, however, for normalized

Jan 1, 1948

By P. D. Gorsuch, I. R. Kramer, D. L. Newhouse

Although many methods have been suggested for the calculation of tensile strength and yield point from chemical composition, their usefulness has been limited to a particular cooling rate or section size. Further limitations have been imposed by failure to take into account many of the alloying elements that exert a considerable influence on the tensile strength or yield point. These systems, nevertheless, have filled an important need in many instances. The value of a system for the calculation of the tensile properties from the chemical composition and cooling rate is that it permits the prediction of the effect of alloying elements and heat-treatment on the mechanical properties, so that more efficient use of alloying elements may be made. Furthermore, it aids in the choice of steel for a given application aid tends to decrease the number of steels that otherwise would have to be tested. It is the purpose of this work to present a method of calculating tensile strength and yield point from the chemical composition and to suggest a method of correlating the tensile-strength and yield-point factors and cooling rate. Steelmakers have been interested for many years in the calculation of the tensile strength of hot-rolled steels. Quest and Washburn' summarize several of the attempts that have been made to devise formulas. They show the inadequacy of each of these formulas and present one of their own. It is apparent from their work that a simple additive equation of the type TS = A + BX + Cy + DZ + . . . , where A, B, C, D, etc. are experimentally determined constants and x, y, z, etc., are the percentages of alloying elements present in the steel, is not adequate to analyze fully the situation encountered in the calculation of tensile strength. For example, it was found that the difference between the calculated and observed values became progressively greater as the carbon and manganese contents were increased. Therefore, the effect of manganese was given as a function of the carbon content. Grossmann, in his work on the harden-ability of quenched steels, and Walter, in his method of calculation of tensile strength of normalized steels, present two cases in which multiplying factors were successfully used to express the combined effect of alloying elements. The factors in both cases were obtained from the fractional increase in hardenability or tensile strength with increase of alloy content. Yield point often is more important in design than tensile strength. For quenched and tempered steels a linear correlation exists between yield 2nd tensile strength.4 This is not true, however, for normalized

Jan 1, 1948

By G. Sanders

The studies reported on in this paper were initiated to draw attention to the severe contamination problem in the Section 30 drilling program at Chimney Creek. The lithologic-subset sampling study reached a different conclusion from that presented in your paper, and I wish to comment on your subsequent analysis of the data and your conclusions. Request for more complete data In the section on subsampling, you mention that the subordinate lithologies were separated and sampled, yet only the dominant-lithology gold value is plotted in Fig. 4. In a contamination study, the reader is interested in the assay values for the individual subsets. Please include a table of the subsample assay data in your reply. Also, please indicate which analytical methods were used to arrive at the gold values in the subsampling study. Turning barren rock into low-grade ore Figure 5 is very revealing and typical of all of the cross sections in Section 30. Note the long strings of low-grade mineralization spread out for hundreds of feet below the ore zones. There were some very high gold values found in certain contaminated fractions during the subset sampling. The conclusion, here, was that the distinctive, strongly-mineralized dolomite layer was probably loose and crumbly and continued to disintegrate during drilling. This caused salting of the unmineralized rock samples below.

Jan 1, 1993

By Galen G. Waddell

Dilation and contraction of the rock surrounding horizontal access open-ings of a deep mine were analyzed during stope advance to determine what type of measurements, made with relatively inexpensive instrumentation, would best reflect the rock behavior. A variety of instruments, mostly mechanical extensometers, were used. Detailed descriptions are given of Down-the-hole extensometers, floating rockbolt clusters, transit surveys, and other instruments and measuring techniques. Although all of the radial-deformation-rate graphs illustrated useful rock behavior data, the most informative graphs were compiled from data procured with the radial extensometers that penetrated, to various depths, the rock around the access openings. An analysis is given of measurement data on the rock around lateral drifts and across and adjacent to the nearly vertical vein of the Star mine, Burke, Idaho. Several useful relationships were found between the rock deformation rate and the stoping process. Information was produced on the elastic state of rock around an underground opening, effectiveness of stope support, rheology of rock, zone of influence around stopes, effectiveness of rockbolts, axis of maximum strain in a plane perpendicular to the long axis of the lateral, and other phenomena. This information could be of particular value in determining location, design, and support of underground openings.

Jan 1, 1966

Particles for heap leaching in conventional circuits are prepared using Cone crushers. Cone crushers are used to crush the ore to the size range between 12-25 mm for heap leaching operations. Leaching from these relatively coarse particles occurs only at the surface and in subsurface regions, which are accessible from the surface by cracks and pores. Since leaching is active in accessible areas, the method of comminution that forms multiple cracks and pores would offer an advantage for heap leach. An investigation was performed in this study to assess if the HPGR forms more cracks and pores than a Cone crusher. X-ray computed tomography (CT) was used to characterize the degree of cracks and pores formed by these two comminution devices that can be used for heap leaching feed preparation. In order to compare the effect of the comminution method on crack network generation, a bulk sample of the zinc ore was crushed by the HPGR at three different pressure settings (45, 95 and 120 bar), the sample ore was also crushed with a Cone crusher for comparison purposes. Products from the Cone crusher and HPGR experiment were then screened into five size fractions ((-25 +19), (-19+16), (-16+9.5), (-9.5+5), (-5+4.75) mm), Subsamples from the ((-25 +19), (-16+9.5), (-5+4.75) mm) size fractions were analysed. The spatial distribution of the crack network of sphalerite particles was characterized using a highresolution industrial X-ray CT system. This paper describes the use of image analysis techniques including image segmentation, which uses a combination of thresholding and other methods to characterize and quantify crack and mineral dissemination in the sphalerite particles after comminution with the HPGR and Cone crusher. The results are validated with those obtained using traditional techniques such as physical gas (with N2) adsorption, mercury intrusion porosimetry, SEM and QEMSCAN.

Jan 1, 2012

By Walshe J. M.

The slow-speed compressor is giving place to the high-speed type, with its greater economy of material and space; and, where very large units are required, the turbo-compressor is supplying the need. In the very large air-supply stations on the Rand, turbocompressor units of a capacity of 20,000 and even 50,000 cubic feet, requiring 4,000 to 13,000 horsepower, are quite a commercial proposition, and have proved a practical success. Air-compressors of this size are, however, very exceptional, and the high-speed reciprocating compressor is quite capable of dealing with the highest outputs so far required in this country and, in the hands of manufacturers experienced in the design of high-speed steam-engines, a very high standard of reliability and efficiency in operation is obtained. The so-called “high-speed” or more correctly quick-revolution type of compressor is now extensively used in mines and collieries; for the air-pressures required for power purposes in mining work, two-stage compression, with an intercooler between stages, is the design usually adopted in best practice. It is not the writer’s intention to describe a variety of high-speed air-compressors but to select as an example of this type of compressor the one with which he is most familiar, and which is probably more largely used than any other, namely, the double-acting two-cylinder two-crank type with automatic light-plate air-valves, and with the working parts lubricated on the forced-lubrication principle. Sectional drawings, efficiency curves, air-cylinder diagrams and other data accompany the descriptions and photographs of compressor design, components and mine applications

Dec 1, 1916

By Y. G. Shiau, J. E. Burke

Several attempts have been made to account for the fact that grains in a fully recrystallized metal will coarsen on annealmg. Two fundamentally different hypotheses have been advanced, with several variations of each. One school considers that the cause of grain growth is the surface energy of the grain boundary. The theory of Jeffriesl that grain size and grain size contrast control growth is an example. The second school considers the primary cause to be a difference in the lattice energy on either side of the grain boundary. The more perfect grains are considered to grow at the expense of their less perfect neighbors, with a decrease in free energy, and a consequent increase in the stability of the system. Burgers2 presents the case for the strain or lattice imperfection theory of grain growth quite completely. The latter theory is attractive, since there is no doubt that differences in lattice energy or lattice perfection can cause grain boundary migration. A recrystallization nucleus grows for this reason as was beautifully demonstrated by van Arkel and Ploos van Amstel.³ Although it is generally stated that grain growth does not precede recrystallization, several workers4-5 have shown that small strains may induce a single crystal in an aggregate to grow, or at least may cause some grain boundary migration. The origin and nature of the imperfections that are considered to be responsible for normal grain growth have never been clearly described, but it is generally agreed that they are a consequence of the difficulty of atomic reorientation in the solid state, and that they do not seriously differ from the type of imperfection that can be introduced by mechanical deformation. An object of the present work was to determine whether the introduction of mechanical deformation would cause grain growth in a specimen which would not otherwise show it under the conditions used. It was also planned to determine the effect of such deformation on the rate of growth in a specimen which would show growth in the unstrained condition. Recently Maddigan and Blank6 have indicated that slightly strained specimens of alpha brass can undergo considerable growth prior to recrystallization if annealed at low temperatures. French7 has reported that at deformations less than 17 pet it is very difficult to detect the beginning of recrystallization in the same material. It was therefore planned to broaden this work to include a complete study of the microscopic behavior of alpha brass under condition~ of temperature, time, grain size and deformation such that recrystallization would not occur or would occur to only a Small extent. Experimental Procedure The brass was prepared by melting cathode copper and commercially pure zinc

Jan 1, 1949

By J. E. Burke, Y. G. Shiau

Several attempts have been made to account for the fact that grains in a fully recrystallized metal will coarsen on annealmg. Two fundamentally different hypotheses have been advanced, with several variations of each. One school considers that the cause of grain growth is the surface energy of the grain boundary. The theory of Jeffriesl that grain size and grain size contrast control growth is an example. The second school considers the primary cause to be a difference in the lattice energy on either side of the grain boundary. The more perfect grains are considered to grow at the expense of their less perfect neighbors, with a decrease in free energy, and a consequent increase in the stability of the system. Burgers2 presents the case for the strain or lattice imperfection theory of grain growth quite completely. The latter theory is attractive, since there is no doubt that differences in lattice energy or lattice perfection can cause grain boundary migration. A recrystallization nucleus grows for this reason as was beautifully demonstrated by van Arkel and Ploos van Amstel.³ Although it is generally stated that grain growth does not precede recrystallization, several workers4-5 have shown that small strains may induce a single crystal in an aggregate to grow, or at least may cause some grain boundary migration. The origin and nature of the imperfections that are considered to be responsible for normal grain growth have never been clearly described, but it is generally agreed that they are a consequence of the difficulty of atomic reorientation in the solid state, and that they do not seriously differ from the type of imperfection that can be introduced by mechanical deformation. An object of the present work was to determine whether the introduction of mechanical deformation would cause grain growth in a specimen which would not otherwise show it under the conditions used. It was also planned to determine the effect of such deformation on the rate of growth in a specimen which would show growth in the unstrained condition. Recently Maddigan and Blank6 have indicated that slightly strained specimens of alpha brass can undergo considerable growth prior to recrystallization if annealed at low temperatures. French7 has reported that at deformations less than 17 pet it is very difficult to detect the beginning of recrystallization in the same material. It was therefore planned to broaden this work to include a complete study of the microscopic behavior of alpha brass under condition~ of temperature, time, grain size and deformation such that recrystallization would not occur or would occur to only a Small extent. Experimental Procedure The brass was prepared by melting cathode copper and commercially pure zinc

Jan 1, 1949

By Hemant Agrawal, Arvind Kumar Mishra

Rock breakage using blasting is one of the important operations of the mining industry. The delay timing decides the initiation sequence of holes in the blasts and is a crucial factor to improve the overall blast performance. Blast-induced ground vibration is an undesired yet unavoidable outcome of blasting. Peak particle velocity (PPV) is commonly used to measure the magnitude of blast-induced ground vibration. Channelization and better utilization of explosive energy delay are provided between blast holes using initiating systems. The use of different initiation systems even on the same site results in a very significant difference in the values of PPV generated. Due to scattered delay timings of pyrotechnic detonators, the scaled distance predictor equations obtained become unreliable. The error/scatter in delay timing leads to overlapping of holes and hence increases in maximum charge per delay. In this paper, an analytical approach has been discussed to measure the overlapping of holes during blasting with initiation systems having inherent cap scatter. The analytical approach will be calculating the probable overlapping of holes due to scatter in delay timing and will help blasting engineers to understand the variation in maximum charge per delay due to pyrotechnic based initiating systems. In this study, a total number of 102 blasts were conducted using different initiation systems at two different opencast coal mine and 221 corresponding blast vibrations events were recorded.

Nov 10, 2020