Search Documents

By Yves Dardel

THE literature concerning the remelting of aluminum and its alloys is very rich. Unfortunately the greater part of the papers about this subject have no scientific value, for the theories or explanations are too often in opposition to the laws of physical chemistry. Furthermore only a few of the methods of purification1,2 are considered in the literature. Hence it has seemed necessary to the author to sketch a general theory of the purification of secondary aluminum. The purpose of the purification is to eliminate the impurities that the charges and the atmosphere of the furnaces bring into the bath during the successive remeltings. Indeed scrap as well as metal can be used when soiled with oil, greases, water, .. , if it has been sufficiently dried and contains oxides. At the melting point of the metal, the oils and greases are decomposed into their constituent elements H2, 02, H2O, C02, CO, CH4, and others. These gases are added to the corresponding gases in the atmosphere of the furnace. The impurities introduced into the metal during the remelting will accordingly be the products resulting from the action of these gases on the liquid bath. The quantity of hydrogen that is soluble in aluminum and its alloys is given by the relation of Sieverts3 as a function of its partial pressure PH2 in the atmosphere [m = K _%/PH, [I]] where K is a constant, which depends only upon the temperature and increases with it. The experiments of Röntgen and Braun4, Röntgen and Möller5, Bircumshaw6 and Winterhager7 have rendered it possible to determine the value of K, when the temperature is inferior to 1.000°K. One obtains: [log K = - 4,702.5 + 0.238 [2]] Besides its usual signification, the term PH2 represents also the internal pressure of dissolved hydrogen, since in the equilibrium, that is, when no gas exchange occurs between the two phases, the pressures of hydrogen in the metal and in the atmosphere must be equal. Eq I shows that when the partial pressure of H2 increases the amount of dissolved hydrogen in equilibrium increases, and that, if the contrary occurs, the quantity of H2 should diminish. However, if for any reason the diffusion of hydrogen is hindered and the total amount of dissolved gas remains constant while the temperature lowers, the internal pressure of H2 increases until it reaches the value of the hydrostatic pressure. At this point, bubbles of hydrogen appear in the bath and escape out of it. The amount of hydrogen in the metal is then limited by a maximum depending on the hydrostatic pressure, which is practically equal to one atmosphere. Indeed hydrogen does not accumulate in the form of a hydride appearing as a separate solid phase. However, even the mechanism of the solubility is not yet elucidated. One does not know exactly as yet, whether the

Jan 1, 1947

By F. C. Farnham

In this paper it is shown that the vertical component of the earth's magnetic field for the area of the United States can be very closely approximated by assuming it to be the sum of the vertical components of two magnetic fields. The first of these is the field of the centered dipole described by J. Bartels,l the axis of this dipole intersecting the earth's surface at two antipodal points, the one in the Northern Hemisphere being at latitude 78.5°N. and longitude 69°W., and the dipole having such strength that the vertical component of its field at its axis pole is 0.63 oersted. The second field is that due to a second dipole situated halfway between the center of the earth and a point on the earth's surface at latitude 38.5°N., longitude 91.5°W., the axis of this dipole being along this radius, the south pole being toward the surface, and the dipole being of such strength that its field at the point on the surface mentioned above is 0.069 oersted. Using the field computed on this basis, tables of latitude and longitude correction factors were computed and are included in the paper. It is also shown that the secular variation in the earth's magnetic field may be roughly accounted for by assuming it to be due to motion of the second dipole described above. Although there is an error in the equation used for computing the strength of the field due to the second dipole, the distribution of the field computed is very nearly that of the assumed arrangement of dipoles. Subsequent work by the author reveals that minor changes can be made in the location of the second dipole, which will make the computed field fit the observed field even more closely. It has also been found2 that the vertical component of the field may be represented equally well by a purely empiric relationship.

Jan 1, 1940

By F. C. Farnham

In this paper it is shown that the vertical component of the earth's magnetic field for the area of the United States can be very closely approximated by assuming it to be the sum of the vertical components of two magnetic fields. The first of these is the field of the centered dipole described by J. Bartels,l the axis of this dipole intersecting the earth's surface at two antipodal points, the one in the Northern Hemisphere being at latitude 78.5°N. and longitude 69°W., and the dipole having such strength that the vertical component of its field at its axis pole is 0.63 oersted. The second field is that due to a second dipole situated halfway between the center of the earth and a point on the earth's surface at latitude 38.5°N., longitude 91.5°W., the axis of this dipole being along this radius, the south pole being toward the surface, and the dipole being of such strength that its field at the point on the surface mentioned above is 0.069 oersted. Using the field computed on this basis, tables of latitude and longitude correction factors were computed and are included in the paper. It is also shown that the secular variation in the earth's magnetic field may be roughly accounted for by assuming it to be due to motion of the second dipole described above. Although there is an error in the equation used for computing the strength of the field due to the second dipole, the distribution of the field computed is very nearly that of the assumed arrangement of dipoles. Subsequent work by the author reveals that minor changes can be made in the location of the second dipole, which will make the computed field fit the observed field even more closely. It has also been found2 that the vertical component of the field may be represented equally well by a purely empiric relationship.

Jan 1, 1940

Report of President The important fact of the year 1916 is that on July 25 contracts were executed by which the American Society of Civil Engineers because an additional Founder Society and arranged to make its permanent home in our building. The contracts provide for the construction of three additional stories to the building, the American Society to pay the cost tip to $250,000, this being considered equivalent to what each other Founder Society had contributed, the American Society to participate in the original Carnegie gift and have an equal share in the property with each other Founder society. The construction of the addition to the building is under way, $62,525.04 having been expended thereon in 1916. It has been found that, clue to war conditions and the advanced price of materials, the cost of the addition will be $300,000. The founder societies have been requested to assume the extra $50,000, one quarter each. This work is in charge of a Building Committee consisting of H. H. Barnes, Jr., Chairman, E. G. Spilsbury, Charles Warren Hunt and Charles F. Rand. At the request of the Founder Societies, important alterations were made in the lecture halls on the fifth floor of the building to make the same suitable for social functions of the societies. The cost, $6,642.08, was advanced by the United Engineering Society but is to be paid eventually by the Founders. The Library of the civil Engineers is being merged with the Library of the United Engineering. Society and the other founder societies. At the present time the membership of the four founder societies is 29,000 and of associate societies 23,000, so that a total of 52,000 engineers now have their headquarters in our building. The value of the real estate now owned by this Society is $1,647,171.16. This sum will be increased at the end of 1917 by the amount of the cost of the addition to the building.

Jan 3, 1917

By Mark A. Ammon

The two most widely used methods of measuring hardness are the Brinell and the scleroscope. In the Brinell method a hardened steel ball is pressed into the steel under a definite load and the area of the resulting depression is measured. The load in kg. per sq. mm. of the area of the depression is taken as a measure of the hardness. Within certain limits the hardness number so determined is independent of the load or the size of the ball. In the scleroscope method a small weight carrying a diamond point is dropped through a glass tube upon the steel and the amount of rebound is taken as proportional to the hard-' ness. In both methods the scale of hardness is an arbitrary one; however, they agree in a comparative may, that is, a steel showing 50 per cent. increase in hardness by the Brinell test mill show approximately 50 per cent. increase in hardness by the scleroscope test. Yet upon consideration of the two methods it appears that, upon a steel which has been carbonized, this should not be the case ; for the scleroscope method gives almost exclusively the surface-hardness, and the condition of the material below the surface has but a slight bearing upon the hardness number. The results given by the Brinell method should, however, be the exact opposite; for the depth of penetration 'of a ball pressed into the steel would be dependent to a large extent upon the condition of the material below the surface. This is particularly obvious when it is considered that the size of the ball ordinarily used in the Brinell method is 1 cm. (about 8 in.) in diameter under a load of 3,000 kg., while the diamond point of the scleroscope is in the neighborhood of 0.01 in. across, fitted in a hammer of about 0.5 oz. weight and dropping from a height of 10 inches.

Jan 1, 1913

By Robert P. Roberts

In order to obtain data on the thermal effect of the blast-furnace jacket and on the water consumption in these jackets a series of tests were run on the 56 by 180 in. blast furnaces at the Great Falls Reduction Department of the Anaconda Copper Mining Co., at Great Falls, Mont. The arrangement of the jacket is shown in the transverse section of one of the furnaces (Fig. 1) on which the tests were made. The nose, spout, and breast jackets have independent water supplies and discharges. The end and side jackets are connected in pairs, as regards water supply, the feed water entering at the bottom of the lower jacket and overflowing into the bottom of the jacket immediately above it, and discharging into an independent overflow pipe for each pair of jackets. Tests were run on the main side and end jackets, the breast jacket, the spout, and the nose. Measurements were taken of the quantity of water discharged per minute and the rise in temperature of the water in its passage through the jacket. The product of these two results, expressed in the proper units, evidently gives the number of units of heat removed per minute by the water. Sufficient work was done on each type of jacket to determine its behavior under different conditions, and the results from each set of conditions were checked by repeating the work from three to six times. The method used was as follows: The overflow from the jacket to be tested was arranged to discharge at will into a barrel, mounted upon platform scales. The discharge temperature was read just before turning the water into the barrel, and just before turning it back to the sluice; if the test lasted more than a minute, additional temperature readings were taken at 1-min. intervals from start to finish. The elapsed time of running the water into the barrel was determined with a stop-watch, and this figure, combined with the in-

Jan 1, 1914

By Robert Roberts

(Butte Meeting, August, 1913.) In order to obtain data on the thermal effect of the blast-furnace jacket and on the water consumption in these jackets a series of tests were run on the 56 by 180 in. blast furnaces at the Great Falls Reduction Department of the Anaconda Copper Mining Co., at Great Falls, Mont. The arrangement of the jacket is shown in the transverse section of one of the furnaces (Fig. 1) on which the tests were made. The nose, spout, and breast jackets have independent water supplies and discharges. The end and side jackets are connected in pairs, as regards water supply, the feed water entering at the bottom of the lower jacket and overflowing into the bottom of the jacket immediately above it, and discharging into an independent overflow pipe for each pair of jackets. Tests were run on the main side and end jackets, the breast jacket, the spout, and the nose. Measurements were taken of the quantity of water discharged, per minute and the rise in temperature of the water in its passage through the jacket. The product of these two results, expressed in the proper units, evidently gives the number of units of heat removed per minute by the water. Sufficient work was done on each type of jacket to determine its behavior under different conditions, and the results from each set of conditions were checked by repeating the work from three to six times. The method used was as follows : The overflow from the jacket to be tested was arranged to discharge at will into a barrel, mounted upon platform scales. The discharge temperature was read just before turning the water into the barrel, and just before turning it back to the sluice; if the test lasted more than a minute, additional temperature readings were taken at 1-min. intervals from start to finish. The elapsed time of running the water into the barrel was, determined with a stop-watch, and this figure, combined with the in-

Jan 7, 1913

By Albert H. Fay, William B. Plank

In practically all rock-excavation problem there is need for a careful study of the rock structure, its fault, cleavage or bedding planes, and even the texture of the rock itself. These studies should form the bases upon which an excavation method is selected and they should be carefully considered in predicting the amount and extent of the excavation. The need for such studies was forcibly illustrated in the problems involved in a cut made in 1929, along and underneath a 200-ft. high rock projection for a State highway near the City of Easton, Pennsylvania. The rock mass was badly faulted and also contained a number of cleavage planes at approximately right angles to the fault planes. Much of this structure was visible and could have been studied and analyzed before the work was begun. The State had rigid specifications as to finished grade and slope of cut, which apparently were made without reference to the geologic structure. The contractor complied with the specifications, under the close inspection of the State engineers. A tunnel blast was placed in the base of the cliff, with the result that 65 per cent more rock was broken than was intended by the specifications. About four years after the blast, the writers of this paper studied the circumstances surrounding the operation, to determine the cause of this excess excavation. Scope of Work The section of the roadway involved was about 200 ft. long and on a 6' curve. It was necessary to relocate points on the curve, from which all faults and cleavage planes were located and measured by the use of transit and clinometer. A plan (Fig. 1) showing the blasting tunnel, the roadway, and traces of the faults and cleavage planes on the level of the roadway, was prepared; also 13 cross-sections at varying intervals, showing the original face of the hill and the face after the blast. The original and final profiles of the rock face, taken from the plans of the State engineers, are shown in Figs. 2, 3 and 4.

Jan 1, 1937

By Arthur Taggart

IN 1900, Elmore found that if an acidulated pulp was stirred up with an oil which was relatively insoluble in and lighter than water, and the mixture was al-lowed to stratify, much of the sulfide would be found hanging to the lower surface of the floating body of oil and could be skimmed off or overflowed with it. The action of the flotation agent here is two-fold, first to select the sulfide from the gangue-what to-day is called collection-and second, to buoy the col-lected sulfide away from the gangue. The action in collecting is illustrated by Fig. 1, which contrasts the behavior of drops of oil brought, under water, to the surfaces of gangue and sulfide particles, respectively. The oil displaces water from the surface of the sulfide; the water displaces oil from the gangue surface. If, instead of considering the solid particles the fixed parts of the system of oil, water and solids, we consider the oil and water fixed and the solids pre-sented to the surface of contact, the condition will be as shown in Fig. 2 ; the sulfide tends to be drawn into the interface and the gangue to be excluded. The sul-fide particles are held in the oil-water surface by the tension of this surface. The buoyant effect is supplied by the oil droplets in bringing the sulfides to the water surface, but not in holding them there.

Jan 6, 1928

By David A. Monaghan, Kenneth R. Maser, Adi R. Gurdar, D. Randolph Berry

APPENDIX A - PNEUMATIC TRANSPORT OF FLY ASH 1. Introduction Two types of pneumatic transport of fly ash are critical to the success of (1) Transport of fly ash from the fly ash truck to the entrance to the borehole. Depending on the surface topography, this may be horizontal, decential and ascential. (2) Vertical downflow of fly ash through the borehole. All fly ash trucks have limited pressure with which they can pump the fly ash. Thus, the pressure drop in the fly ash hose will define the maximum length for pumping and consequently the maximum distance that the fly ash truck can be parked from the auxiliary blower. The same relationships describe the flow of the dilute fly ash-air mixture produced by mixing with the auxiliary air from the blower and thus define the selection of the pipe diameter. These are im¬portant considerations in the proper selection of the location of the passages to be sealed and the type of surface preparation required. The flow characteristics of fly ash down the borehole determine the selection of the minimum borehole diameter and the blower pressure. This appendix presents theoretical analyses of these flow regimes and summarizes the limited experimental data obtained during the field tests at Grant Town, described in Section 8.4. The analysis for the borehole flow is presented first as it is of greater interest to the program. This is followed by a discussion of the horizontal flow.

Jan 1, 1973

By Arnaud Faucher, Amar Sabih, Sudarshan Martins, Tristan Martin, Sami Makni, Peter Radziszewski, Poorya Hosseini, Francois-Raymond Boyer

The measurement of acoustic signals produced by a tumbling mill has been previously used to determine the operating state of the mill and correlate the variations of the sound intensity with the operating conditions of the mill. Separately, the discrete element model (DEM), a software simulation of the mill, was developed to provide insight into the operation of the mill. Presently, there has not been much work reconciling the DEM simulation of the mill with the acoustic signal. Working from basic principles of linear, time-invariant systems, agreement between an acoustic DEM simulation and the measured signal is sought. First, the impulse response function of the mill is measured. The DEM provides the forces applied to the mill shell as a function of time. A convolution of these simulated shell forces and the transfer function gives the simulated acoustic signal. This signal is compared to the measured acoustic signal, both in the time domain and the frequency domain. Finally, a discussion of the results is given.

Jan 1, 2012

By Edward Marszalek, Boleslaw Firganek

The paper deals with a computer method and algorithm of optimization of the rescue routes for the endangered staff in the case of fire in a given place of the mine. The adapted method is based on the objective function and realizes the algorithm of the shorest path with weighers assigned to it. The objective function is so defined that it reflects possibly all the hazards and difficulties arising during a fire in the mine. The algorithm is enhanced by an empirical formula for calculation of the smoke zone as result of a mine fire. The presented results of computations of optimal routes for several simple examples using the canonical scheme of the mine network and simulated fires are satisfying and prove the method, the algorithm and the coded program to be correct. The program will be a part of the software library of the mine ventilation engineer. The data for the program will be updated on-line from the fire detection systems.

Jan 1, 1989

By H. E. Stauss, E. I. Salkovitz, F. W. von Batchelder

EXISTING information regarding the structure of a spherulite in nodular cast iron is based on optical studies. According to these data, a nodule consists of an aggregate of graphite crystallites radiating from the center, with the closely packed basal planes at right angles to the radii. The c axes lie along the radii. This view faces some uncertainty in the fact that the c axis does not represent the accepted direction of fastest growth in graphite. To supplement the optical information, X-ray studies have now been made. The principle used was to screen the nodule in greater part from the X-ray beam and expose only a minor cap. As successively larger portions of the nodule were introduced into the X-ray beam, any differences in the X-ray patterns could be observed. Such photographs have been taken with chromium radiation and a Laue camera. The graphite nodule itself, about 0.010 to 0.025 in. in diam, was mounted with vaseline on a micrometer screw for control of the linear motion. The nodule rotated about 45" each time that it was translated linearly. The nodules were obtained from magnesium-treated hypereutectic iron by electrolytic solution of the iron in hydrochloric acid. In Fig. la is shown the pattern of the thinnest cap examined. In Fig. lb is shown the pattern of the same nodule moved 0.003 in. farther into the X-ray beam, and rotated 45" at the same time. Figs, la and lb indicate incomplete circles for graphite (the two outer circles arise from graphite) with the side arcs much weaker than the top and bottom ones. The arcs obtained are themselves not continuous in intensity but vary with maxima of intensity some 15" and 30" apart. The structure of the nodule that would give rise to such a pattern can be explained as follows. Basically the nodule consisted of small crystallites. The discontinuous character of the diffraction rings demonstrates that the nodule was not composed of randomly oriented crystallites. The strong vertical reflections and the weak lateral reflections show that the reflecting planes were roughly normal to the radii. The absence of sharp reflection spots suggests that the nodule did not contain large crystals. The sharpness of the diffraction rings in their radial direction shows that the variations in intensity along the arcs were not the result of line broadening resulting from extremely small crystals. In the diffraction patterns two rings corresponding to graphite were found. The third and inner ring in the figures originated in the vaseline. The graphite rings correspond to the a and ß lines reflected from the basal planes, showing that the radii of the nodules are the [0001] direction normal to the basal planes of graphite. The picture of the structure that is formed is, therefore, one of aggregates of crystallites. Within each aggregate the c axes of the crystallites tend to align themselves in the radial direction of the nodule, although these axes deviate somewhat in direction by a continuous variation of angle. Correspondingly the basal planes of the graphite crystallites are generally normal to the radii. It is a pleasure to acknowledge the assistance of M. C. Bloom and R. P. Dunphy of this laboratory.

Jan 1, 1952

By Ralph V. Higgins

This paper concerns the magnitude of the amount of supersaturation that occurs in an underground reservoir during the flow of oil and gas to wells and to the amount of undersaturation that occurs during repres-suring of an oil reservoir where some effective permeability to gas exists. The study is based on earlier laboratory findings of other investigators on the rate of diffusion of gas in oil as a function of the depth of oil. Utilizing these relationships and the principles of reservoir mechanics, a quantitative estimate of undersaturation and super-saturation was calculated. The results showed that the diffusion of the gas is rapid enough that for all practical purposes no supersaturation exists during the flow of oil to wells or undersaturation during repressuring in reservoir sands having some effective permeability to gas. The reason diffusion of the gas virtually keeps the oil saturated is the long time required in radial flow for oil to reach the well and the slow rate at which pressure in reservoirs is increased during repressuring. INTRODUCTION Knowledge of the phase relationships during flow of gas and oil in an underground reservoir is essential to operating the reservoir in the most efficient manner. In material-balance calculations and in fluid-flow studies, the oil is assumed to contain all the gas that it will dissolve at given temperature and pressure. Pressure-volume-temperature relationships are normally obtained in the laboratory using "bottom-hole" or combined samples of the reservoir fluids. In such laboratory determinations equilibrium is obtained between the oil and gas in the pressure cells by mechanical agitation. During the flow of oil and gas in reservoirs, however, no comparable agitation occurs to mix thoroughly these fluids to aid in effecting equilibrium between the two phases. During repressuring of a partly depleted underground reservoir, the gas is usually injected into the reservoir faster than the oil can absorb it; consequently, the oil is undersaturated. On the other hand, as the oil flows through the reservoir to the wells during producing operations the pressure decreases faster than the gas in solution can diffuse through the oil to the gas phase. The oil therefore is supersaturated with gas. Where the oil is undersaturated, gas diffuses away from the gas-oil interface, and where it is supersaturated the gas diffuses toward the interface. In either case the gas moves from a higher to a lower saturation. This report contains the results of a study of the factors influencing the degree of nonequilibrium of the phase relations of oil and gas in porous mediums during the flow of oil through reservoirs to wells and also during the injection of gas into partially depleted sands. Data from an underground reservoir are presented and the degree of supersaturation during the flow of the oil through the reservoir to the well is approximated. Also data from another reservoir are used and the degree of undersaturation during the repressuring operation is calculated. In addition, the flow rates of oil in laboratory experiments and in underground reservoirs are compared, as data from the laboratory are often used to interpret events in the reservoir, and the rates of flow influence appreciably the degree of nonequilibrium. Much of the contents of this report was prepared in 1943; but, because of other activities during and since the war, the manuscript was left untouched until 1952, when it was decided to include an estimate of the amount of undersaturation during repressuring as well as supersaturation during flow.

Jan 1, 1955

By R. D. Satterley

THE Sherwood mine is an iron-ore mine owned and operated by the Inland Steel Co. in the Iron River district of the Menominee Range in Michigan. The property consists of an 80-acre tract in the village of Mineral Hills, about a mile north of the city of Iron River. The ore mined is a reddish brown, nonbessemer hematite and limonite. The ore bodies lie in a large syncline having an east-west strike and are associated with a rock structure that is folded in a complex manner. The two 40-acre tracts run north and south and the shaft is at about the center of the north forty. The shaft is 1286 ft. deep, with the principal operating level at a depth of 1000 ft. from surface. A new level at a depth of 1200 ft. is in process of development. The ore body at the 1000 ft. level is east and west at approximately the line between the north and south forties and at this elevation is from 50 to 250 ft. wide and extends above the level at varying heights of from 50 to 250 feet. The 1000-ft. haulage drift extends south from the shaft, through the east-west ore body to the slates on the south side of the body. The ore body was intercepted in the drifting at about 800 ft. from the shaft and was about 200 ft. wide at that point. A crosscut was extended to the east and west property lines along the south boundary of the ore body. This east-west ore body is laid out in areas 80 ft. wide for stoping with pillars 40 ft. wide. With this plan a stope is approximately 80 by 200 ft. and has a pillar on both sides that is approximately 40 by 200 ft. The ore has a height of from 50 to 250 ft. above the elevation of the level, therefore the height of the stopes varies in accordance with the height of the ore body at each location. From the crosscut, two main raises, each 6 by 7 ft., are put up into each 80 ft. stope area (Fig. I). One of the main raises serves as a manway and the other as an ore raise, through which the ore is transferred from the stope to the tramming equipment. The original layout was for scraping of the ore from under the stopes into the ore raises. The ore raise is put halfway (east and west) along the 80-ft. stope area and usually is in iron formation. The manway and ore raise are on approximately 15-ft- centers. These main raises are put up to a height of from 22 to 30 ft. above the level floor, then from the top of the ore raise a scraper drift (8 X 8 ft.) is driven across the width of the ore body, which is in the neighborhood of 200 ft. From the scraper drift, mill raises are put up at 12 ½ -ft. centers, staggered on opposite sides of the drift, and these are extended 23 ft. above the elevation of the scraper-drift floor. The sublevel connecting the top of these mill raises is called a mill "sub." Other sublevels are developed parallel to the scraper and mill subs at 25-ft. vertical intervals above the mill sub. The mill sub and the other subs above the mill sub are known as sublevels or dog drifts, and are 4 ft. wide and 6 ft. high. These dog drifts

Jan 1, 1945

By R. D. Satterley

The Sherwood mine is an iron-ore mine owned and operated by the Inland Steel CO. in the Iron River district of the Menominee Range in Michigan. The property consists of an 80-acre tract in the village of Mineral Hills, about a mile north of the city of Iron River. The Ore mined is a reddish brown, nonbessemer hematite and limonite. The ore bodies lie in a large syncline having an east-west strike and are associated with a rock structure that is folded in a complex manner. The two 40-acre tracts run north and south and the shaft is at about the center of the north forty. The shaft is 1286 ft. deep, with the principal operating level at a depth of 1000 ft. from surface. A new level at a depth of 1200 ft. is in process of development. The ore body at the 1000 ft. level is east and west at approximately the line between the north and south forties and at this elevation is from 50 to 250 ft. wide and extends above the level at varying heights of from 50 to 250 feet. The 1000-ft. haulage drift extends south from the shaft, through the east-west ore body to the slates on the south side of the body. The ore body was intercepted in the drifting at about goo ft. from the shaft and was about 200 ft. wide at that point. A crosscut was extended to the east and west property lines along the south boundary of the ore body. This east-west ore body is laid out in areas go ft. wide for stoping with pillars 40 ft. wide. With this plan a stope is approximately 80 by 200 ft. and has a pillar on both sides that is approximately 40 by 200 ft. The ore has a height of from 50 to 250 ft. above the elevation of the level, therefore the height of the stopes varies in accordance with the height of the ore body at each location. From the crosscut, two main raises, each 6 by 7 ft., are put up into each 80 ft. stope area (Fig. 1). One of the main raises serves as a manway and the other as an ore raise, through which the ore is transferred from the stope to the tramming equipment. The original layout as for scraping of the ore from under the stopes into the ore raises. The ore raise is put halfway (east and west) along the 80-ft. stope area and usually is in iron formation. The manway and ore raise are on approximately 15-ft. centers. These main raises are Put up to a height of from 22 to 30 ft. above the level floor, then from the toll of the ore raise a scraper drift (8 X 8 ft.) is driven across the width of the ore body, which is in the neighborhood of 200 ft. From the scraper drift, mill raises are put up at 12½-ft. centers, staggered on opposite sides of the drift, and these are extended 23 ft. above the elevation of the scraper-drift floor. The sublevel connecting the top of these mill raises is called a mill "sub." Other sublevels are developed parallel to the scraper and mill subs at 25-ft. vertical intervals above the mill sub. The mill sub and the other subs above the mill sub are known as sublevels or dog drifts, and are 4 ft. wide and 6 ft. high. These dog drifts

Jan 1, 1946

By J. S. Aronofsky

The results of polentiometric model studies and numerical computations are described. The purpose of these studies was to determine the influence of the mobility ratio on flooding efficiencies during water encroachment in petroleum reservoirs, in systems of regular well geometry. The direct line drive well pattern having relative spacing distances of one and one-half to one was investigated for water to oil mobility ratios of 10. 1. and 0.1. The results of these studies indicate that the pattern Sweep efficiency i.; very dependent upon the mobility ratio. INTRODUCTION The almost universal occurrence of water in the immediate neighborhood of oil-hearing sands lends considerable emphasis to the desirability of having a rational analysis of water encroachment into petroleum reservoirs. This problem has 1)become increasingly important with the accelerated use of water injection for secondary recovery operations. The water encroachment problem has been studied from both the theoretical and experimental viewpoints by Muskat.' He has formulated, in a precise manner, differential equations to express flow in a water encroachment system, and rigorous analytical solutions have been developed for the linear, radial, and spherical cases.' However, it becomes exceedingly difficult to solve the encroachment problem rigorously for any general two-dimensional system in which the shape of the two-fluid interface is not immediately evident from the geometry of the system. The difficulty lies in the fart that a rigorous analytical solution requires that the shape of the two-fluid interface be known simultaneously with its instantaneous posititon and with the pressure distribution on both sides of the interface. Although this paper concerns the study of the two-fluid system of oil and water. the methods described in the paper are generally applicable to other systems of incompressible and immiscible fluids in which the displacing fluid sweep-the displaced fluid down to a residual value. In each region it is assumed there is only one mobile fluid and its mobility is constant throughout the region. The Same procedure. with minor alteration, is applicable for gas injection systems provided the assumption can be made that both the displaced and displacing gases can be described by steady state formulas. For the particular two-fluid problem considered in this paper, there is a relative permeability. K, and a viscosity. p. associated with the water zone, and a different permeability and viscosity associated with the oil zone. The K/p (mobility value associated with a particular volume element of the porous medium. at any instant of time. will depend upon whether the element is ahead of. or behind the advancing interface. It is assumed that all volume elements ahead of the interface are characterized by the K/p value for oil, while all the elements behind the interface are characterized by the K/p value for water. That is. the K/p value in the oil zone is constant throughout the oil zone. and the K/p value in the water zone is also constant but different from the value in the oil zone. The symbols are defined at the end of the paper. The well pattern chosen for initial study is the direct line drive; the swept-out area at breakthrough was determined by two different methods which are described in the section on theory. These are: 1. Potentiometric analyzer 2. Numerical computation The use of the potentiometric analyzer for studying water flooding problems is adequately described in the literature, particularly for cases where the mobility in the water zone is assumed equal to the mobility in the oil zone." ' 5

Jan 1, 1952

By JIACHENG XIE, Juanli Li, Wenyong Du, Tao Cui, Mengyao Dong, Pengfei Huo

The operation of intelligent coal mining in complex geological environment is still unable to realize automation. In order to realize the autonomous cutting of fully mechanized mining equipment and improve coal production, a mining and transportation equipment dynamic advancement path planning method based on spatial kinematics coordinate deduction prediction and real-time correction prediction of coal-rock state identification of equipment cutting current index are proposed. Firstly, the spatial motion law of the mining and transportation equipment is analyzed, and the mathematical model of the spatial motion of the mining and transportation equipment is established. The relationship between the adjustment of the shearer rocker arm and the pose change of the scraper conveyor is determined, and the coordinate deduction model of the spatial advancement position of the equipment is determined, which provides a theoretical basis for the advancement path planning of the mining and transportation equipment. Then, on the basis of the mathematical model construction, combined with real geological data and equipment information, the three-dimensional dynamic planning of the advancement path of the mining and transportation equipment is carried out from the two dimensions of the horizontal advancement direction and the shearer walking direction. At the same time, the relationship between the cutting current index of shearer and the state recognition of coal-rock mass is analyzed, and the coal-rock mass state identification of cutting current and the adjustment of rocker arm model is constructed, and the real-time dynamic correction of three-dimensional path is carried out, so that the planned path can better adapt to the sudden change of real geological environment. Then, using the unity3d virtual reality technology, a simulation system for the horizontal advancement path planning of the virtual mining and transportation equipment is constructed, which simulates the real advancement operation process of the mining and transportation equipment and conducts advancement training. Finally, the dynamic advancement scheme update prediction based on the existing actual cutting but ahead of the actual cutting is realized in the virtual scene, and the optimal scheme is transmitted into the existing prediction cutting system to guide the actual physical equipment mining. The path planning method can control the coordinate position error of the advancing cutting path within 15 mm, which provides ideas for the research on the advancing path planning of fully mechanized equipment.

Nov 22, 2022

By Theodore Hatch

The pneumatic rock drill operates essentially as a crusher. The rock is shattered into a powder that is removed from the drill hole by the air stream introduced through the hollow drill steel. Particles thus produced vary in size from 1/4 in. or larger down to diameters too small to be revealed by the ordinary microscope. The power consumed by the drill is proportional to the new surface area of the powdered material, therefore the greater the proportion of "dost" produced, the higher the power consumption and the lower the drilling speed. A considerable amount of material ejected from the hole settles on the rock and much of this falls back as the mound builds up to be crushed further before it is removed again. The cushion of dust at the bottom of the hole reduces the effectiveness of the blow of the bit and thus lowers the rate of drilling. The unfavorable working conditions created by the dust also reduce the drilling speed by lowering the efficiency of the operator. Thus, the dust produced by rock drills constitutes a serious drawback to economical performance on all drilling operations. To the economic objections, one must add the more important objection to the health hazard created when the dust contains free silica (quartz). The silicosis problem is a familiar one in many mines, tunnels, and other underground operations as well as in quarries and other types of open rock excavation. Dust is a necessary end product of all pneumatic drilling operations. Its production cannot be eliminated although the proportion of microscopic particles can be reduced by using improved drill steel, proper methods of sharpening, more efficient drills, etc.—improvements that increase the drilling speed largely by increasing the size of the cuttings. The absolute improvement secured in this way is not great, however, and the pneumatic drill must always remain a dust-producing machine. Definite benefits do result, on the other hand, from the use of dust-control equipment that captures the dust as it emerges from the hole and conveys it to a remote point of discharge. Dust production continues, but dust dispersion into the atmosphere is prevented. The dust is removed as rapidly as it is formed, with the following results: (I) The silicosis

Jan 1, 1937

By Bogar D. V

Often dewatering of coal tailings is inhibited by the presence of clays, making it difficult to obtain a high concentration, handleable coal tailings. The net result can be a low concentration, chocolate mousse-like tailings which poses significant sedimentation problems in a tailings dam and represents a significant environmental problem. This paper examines the coal tailings from a Hunter Valley colliery where the tailings properties are influenced significantly by the presence of montmorillonite clay. The influence of the calcium ion on the rheology and sedimentation/compression behaviour of coal tailings . containing montmorillonite already dispersed in water was investigated and revealed that very little improvement in the properties is achieved through the coagulation. The preliminary investigations also indicated that the properties of the tailings were dominated by the presence of the montmorillonite clay. Thus investigations were carried out on the clay alone in water. Investigations into the effect of dispersing samples of the clay alone in water and then coagulating with calcium compared with dispersing the clay directly into calcium ion solutions at the same calcium concentration showed huge improvements in the rheology, compressibility, sedimentation rates and sediment solids concentrations for the second dispersion method, which can be called controlled dispersion. The sediment volume fraction solids improved by more than a factor of two by controlling the dispersion of the clay. The reason for the improved properties lies in the suppression of the initial swelling of the clay, which is initially in the sodium form, thus maintaining the parallel orientation of the platelets that is present before wetting. While swelling is being suppressed, ion exchange occurs with the calcium which results in permanent swelling suppression. In the uncontrolled dispersion case where swelling is uninhibited, the clay is allowed to break up and despite the powerful coagulating nature of the calcium ion, the random orientation of the high aspect ratio clay platelets inhibits effective coagulation. Results indicate that the initial electrolyte concentration of the washwater in a coal washery is the critical factor controlling the dewaterability of clay tailings and the handleability of the dewatered product rather than the actual act of coagulating with the calcium ion. The results presented are of clear practical significance and indicate how coal tailings problems where clay dominates the rheology can be improved considerably by knowledge of the surface chemistry.

Jan 1, 1995