Search Documents

By John F. Wiss

A series of controlled experiments was conducted at four surface coal mines to study the effects of certain blast parameters upon the ground and air vibration. Preliminary scale-model blasts were conducted at a quarry to provide basic data. It was found that the amplitudes of the ground and air vibration were controlled by the maximum explosive weight per delay. Either cube root or square root scaling could be used for the seismic amplitudes, and cube root scaling could be used for the overpressure amplitudes. Both amplitudes were not significantly affected by the total charge weight per blast, the attitude of the boreholes, or the charge length or diameter. The overpressure amplitudes were affected by the charge depth, the use of cover over surface detonating cord, and the use of adequate stemming. The length of the delay intervals and the spacing of holes were important in determining the potential for reinforcement of the amplitudes in certain directions from the blasts. In downwind directions from the blast, the attenuation of the overpressure with distance decreases. Surface terrain t did not significantly affect the overpressure amplitudes within the range investigated. The type of overburden affects the generation of both amplitudes and the propagation of the seismic amplitudes. Spectral analysis of the ground and air vibration is reported. A bibliography of pertinent literature is included as an appendix. A scaled distance of 300 ft/lb1/3 should produce a peak particle velocity of less than 1 ips and an overpressure of less than 128 dB linear peak. For square root scaling, a scaled distance of 75 ft/lbl/2 should limit the ground vibration to less than 1 ips.

Jan 1, 1978

By Israel Liebman

The Bureau of Mines conducted an investigation to determine those factors that are significant in affecting the velocity of flames propagating along the boundary separating gaseous fuel and air. In addition the aerodynamic motion of the gases in the vicinity of such interfacial flames was delineated. Parameters in the study included flammable zone thickness, flammable zone concentration of gradient, fuel type, and position of the flame relative to various environmental surfaces. Of all these factors, the flammable zone thickness and burning velocity of the stoichiometric mixture were found to have the most significant effect on the flame speed. Notion of the gases in the vicinity of the interfacial flames was examined by particle track and interferometric techniques. The relative velocity of the interfacial flame with respect to the unburned gas on the central streamline was found to equal the burning velocity of a stoichiometric homogeneous fuel-air mixture. In addition, it was observed that the composition of the lean fuel-air mixture at the boundary of the combustion zone appears to be less than that defined as the fuel's lower flammable limit.

Jan 1, 1968

By E. D. Fox

Introduction The financial statement of the hypothetical Gold Mining Company, which forms the background of this survey, was designed for the Institute with the express abject of having it assessed in respect to Profits by the several taxing bodies representing the Federal and Provincial Governments, which comprise the Dominion of Canada. On the completion of the figures, copies were sent to the several Ministers of Mines, accompanied by a request that they be submitted to their taxing authorities and assessed accordingly. The response, while it was not general, was very favourable, and at all times we were treated with the utmost courtesy and patience, and what has been set forth in the compilation bears the authentication of the various government officials who are immediately concerned with taxation. The data itself constitutes a fairly comprehensive digest of taxation as it directly applies to gold mining profits in Canada. The Hypothetical Balance-Sheet (See Exhibit A) In the balance-sheet schedules 1 and 2 (Exhibit A), income is divided between taxable and non-taxable classifications, and here it should be noted that the division contemplates only the assessment for Dominion income tax. The same applies to the factors of exchange and depletion. Therefore, in making comparisons, it is to be borne in mind that the set-up for assessment to the Provinces, that is, Manitoba and Alberta, will stand as if the gross non-operating income is taxable, with the reservations as shown in the notes below the schedules.

Jan 1, 1934

By David A. Summers

Coal is increasingly viewed as one of the major fuel resources of this country for the remainder of this century. The need to extract a greater percentage of the coal in a given seam, together with advantages of improved safety, indicates that longwall mining will become more widely used within this time frame. A novel method of mining coal on a longwall face, utilizing high pressure water jets, is herein described. The mining machine proposed will exploit the stress conditions which exist on a longwall panel in order to achieve the required productivity while at the same time reducing respirable dust and methane ignition hazards. The water jets will excavate only the boundary of the extracted seam section, and thus the energy requirement of the machine will be minimized. The action of the machine is similar to that of an existing coal plow, except in that the wedge teeth of the plow are replaced by oscillating high pressure water jets. The machine can, therefore, cut to the depth and at the speed of existing shearer units at equivalent power levels. The removal of impact stresses from the machine will reduce downtime required for maintenance and replacement of picks and lower the load on the haulage motor of the system. The ability of the machine to increase the depth of cut without an increase in horsepower will further improve productivity when transportation systems to remove the greater production are in operation.

Jan 1, 1974

By Qiang Wang, Jiaqiang Yu, Chunhui Fan, Yong Wang, Changyu Jin, Jun Bai, Yu Lu

Accurate ore blending necessitates an in-depth understanding of movement trajectories of fragments and the spatial evolution of the displacement field in the bench during blasting, Accurate ore blending is currently one of the most complex challenges faced by mining engineers. In light of this problem, a systematic study was conducted in this paper using neural network and numerical simulation based on field monitoring data. A nonlinear mapping relationship was established between the mechanical parameters of rock mass and the displacements of the monitoring points. The measured displacements of monitoring points under blasting were input into the neural network, which used back-calculation to derive the mechanical properties of the rock mass. These parameters were then applied in a forward calculation to analyze the movement trajectory of the monitoring points. The results showed that the calculated displacements were in good agreement with the monitoring results during the. The average relative errors in the horizontal and vertical displacements were 4.12% and 15.2%, respectively. Furthermore, the muckpile profile was in an inverted recumbent “S” shape after bench blasting, which was consistent with the actual shape of the muckpile. This verified the rationality and accuracy of the method proposed in this study. Finally, the movement trajectories of particles in the bench and the spatial evolution law of the displacement field during bench blasting were determined based on the calculation results, offering theoretical support and fundamental information for accurate ore blending.

Dec 16, 2023

By Rong. G., T. Q. Lin, W. Du

Based on analysis of the evolutionary history of the valley in Baihetan, the mechanism of asymmetrical evolution, gradual migration-incision evolved from left bank to the right, is revealed in Baihetan river valleys. The process of in-situ stress evolution is carried out by using the Universal Distinct Element Code (UDEC). Consequently, the numerical results which indicate the main regulations of that stress field are as follow: (1) The phenomenon termed "high in-situ stress fold" appears in the bottom of the valley. With the maximum principal stress being 28-34 MPa, the stress increases significantly at a vertical depth of approximately 130 m. (2) The in-situ stress presents zonal distribution along the bank slope. It is apparent that the in-situ stress field consists of stress relaxation zone (SRZ), stress concentration zone (SCZ) and original stress zone (OSZ). The horizontal depth of stress relaxation zone varies from the left bank (roughly 200 m) to the right (about 120 m). Furthermore, the stress evolution of the left bank slope is studied. As a result, it is found that asymmetrical erosion contributes to the difference of the in-situ stress distribution as a critical factor, between the left bank and the right. And for an asymmetrical valley, the evolutionary process of in-situ stress field is a circular procedure, which includes the incision of valley, the accumulation of landslides and the migration of valley.

Jan 1, 2015

By Michael Oakland

This paper will discuss the design analysis of sheet pile cofferdams for static and dynamic blast loads. Following construction of the new Willis Avenue Bridge across the East River between Brooklyn and Manhattan, in-river piers No. 9 and No. 10 from the former bridge were demolished, partially by explosive charges. The blast at Pier 10 was conducted first and though the demolition charge was relatively small, it gave confidence that the sheeting could be designed to resist the blast load. This paper primarily summarizes our analysis and performance of a sheet pile cofferdam at Pier 9 used to withstand the larger blast loads, contain the blast debris, and allow excavation of the pier below the existing river bed mudline. The program NLFlex was used to predict stresses and deformations of the cofferdams under dynamic blast loads, using simplified equations to estimate the underwater blast pressures. Specifically, the analysis focused on the stresses in the struts, waler beam, sheet pile interlocks and connection of the sheeting to the waler beam. Design included allowing plastic deformations and limited rupture of the sheet pile interlocks under the blast loading. Comparisons are made between stresses assessed by the dynamic finite element modeling and empirical relationships used within the industry. The performance of the system after the actual blast is discussed as well as details of the performance of welded vs. bolted connections within the system.

By J Y. C Lo

The construction of two drainage tunnels and the associated subvertical drain system at the Po Shan area in Hong Kong was completed in December 2009. This project is the first of its kind to utilise drainage tunnels and a network of subvertical drains to regulate the groundwater table to enhance the long-term stability of the hillside of Po Shan area.The groundwater levels, monitored by preinstalled piezometers, once exhibited dramatic drops during drilling of the subvertical drains; however, have recovered from natural replenishment after effectively plugging of the drains. The level of groundwater drawdown is in line with the design function of the subvertical drains. In order to understand the groundwater flow pattern in the Po Shan area during and after construction and to set out operation schemes for the subvertical drain system so as to control the groundwater table in the Po Shan area, a post-construction review has been carried out to examine the behaviour of the drainage system and its impact on the surrounding subsurface groundwater flow.This paper presents a review of the groundwater monitoring data during and after the construction of the drainage tunnel system covering a period of over 3.5 years. A simplified conceptual hydrological model is developed, which has been verified by the monitoring data, to capture the key elements with regard to groundwater variations in different stages of the construction. The performance of the tunnel and subvertical drain system as revealed from these field measurements is discussed.

Mar 8, 2011

By Jeremy Spearman, Mark Lee, Jon Taylor, Neil Crossouard, Bramley Murton

"SUMMARYThis paper describes challenges faced when executing a programme of monitoring to measure the dynamics of currents and sediment plumes at a seamount and the solutions identified to deliver the measurements. The study site was the Tropic Seamount, which extends some 3300m above the surrounding seabed and is found at the southern limit of the Canary Island Seamount Province. The purpose of the study, which forms part of the Marine E-tech project, was to provide information on the interaction of flows with the seamount and to assess the behaviour of sediment plumes that could be generated from potential seabed mining operations targeting the recovery of ferromanganese crusts. Since the crest of the seamount is submerged to a depth of 1000m, much of the work was undertaken using remotely operated and autonomous vehicles supported by measurements from the surface vessel. Despite only limited information on currents being available for planning purposes, the combination of short term forecasting using a 3-dimesional hydrodynamic model of the study area coupled with the collection and analysis of reconnaissance data collected during the first phase of measurement activities made it possible to plan and execute a number of detailed hydrodynamic experiments on the seamount crest. The results of these experiments have advanced the understanding of the behaviour of sediment plumes in the deep ocean and will ultimately improve our ability to manage the impacts which may arise from deep sea mining operations."

Jan 1, 2017

By Wilbur Duvall

For the past few years the Applied Physics Branch has been investigating, experimentally, the generation and propagation of strain waves in rock. The strain waves are produced by the detonation of a high-velocity explosive placed in a small cavity in the rock. Strain gages mounted in the solid rock surrounding the cavity record the strain pulses propagated away from the source. Numerous strain-wave pulses have been recorded in different rock types for charges of various sizes and at various distances from the charge. Analysis of these records has shown, among other things, that there is associated with the strain wave a characteristic pulse width. This pulse width is dependent on the rock type and the distance from the shot point to the gage, but is apparently independent of the charge size or cavity size. Recent published literature on the generation and propagation of seismic waves indicates that the characteristic frequency of an elastic wave generated by an explosion should be a function of the rock type and the size of the cavity created by the explosion. Also, internal friction in the rock would produce absorption of high-frequency components, which would cause continual change in the shape of the pulse propagated. As the experimental data did not verify the expected change in pulse shape with cavity size, a theoretical investigation of the vibrations associated with a spherical cavity in an elastic medium was undertaken.

Jan 1, 1950

By Robert D. O'Brien

"INTRODUCTION The Miscellaneous Minerals Division of the War Production Board requested the Bureau of Mines to investigate the Gallatin corundum property as a possible source of corundum, which was in short supply due to the war. The Gallatin corundum property, also known as the ""Fuller mine"", the ""Montana Corundum mine"", and as the ""Old Qorundum mine"" was first examined by a Bureau of Mines engineer 2/ in July 1943. Bureau of Mines work on the property started October 11, 1943, was recessed May 5, 1944, and was resumed in October 1944 when the diamond-drilling program started. The project was completed February 7, 1945. The data obtained are given in this report.The Federal Geological Survey made a reconnaissance survey in the spring of 1943 and mapped the area the following autumn. The results of these surveys are contained in a memorandum report prepared in December 1943.ACKNOWLEDGMENTSIn its program of investigation of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual investigative work, and prepares the final report. The Metallurgical Branch, R. G. Knickerbocker, chief, analyzes samples and performs beneficiation tests."

Aug 1, 1947

By Hong Yong Sohn, Xiaoyi Cai, Wei Wang, Liangzhao Mu, Fengqin Liu, Hongliang Zhao

Thebottom-blownsmeltingtechnologyhasbeenwidelyadoptedinnon-ferrousmetalsmeltingindustries.Thelargestbottomblown smelting furnace used in copper smelting was numerically simulated to improve the stirring effect in the molten bath by optimizing the oxygen injector arrangement and blowing parameters. The results show that a small injector spacing leads to gas jet coalescence, which is detrimental for smelting efficiency, increases copper loss and shortens furnace service life. Three schemes were proposed to improve the uneven stirring and reduce the gas jet coalescence by increasing the axial spacing of the injectors, the radial installation angle and the gas injection angle. Changing the axial spacing of the injectors can significantly reduce the gas jet coalescence, yielding the best stirring effect. The results of simulation suggested that when the axial spacing of the injectors was increased from 0.380 m to 0.610 m, the mean melt velocity in the mixing zone increased to 0.243 m/s, which was 20.9% higher than that before the optimization. Meanwhile the RSD (relative standard spatial deviation of melt velocity) decreased from 123% to 84%. In the actual production, the matte content in the smelting slag decreased from 6.57% to 3.12% after changing the axial spacing of the injectors from 0.380 m to 0.610 m.

Apr 10, 2024

By Tyler Lahti, Peter Borgacci, Mary Jane Ferraro, Prakash Nadesparan

Toronto Tunnel Partners (TTP), under contract to Metrolinx/IO, is constructing new twin rail tunnels under the Highway 401 & 409 interchange to accommodate additional tracks to support the GO Expansion program for future two-way, all-day service. The new tunnels are being constructed using the Sequential Excavation Method (SEM) and utilize a tunnel pre-support system consisting of a series of 800 mm diameter steel pipes to form a pipe canopy. The pre-support pipes were installed with an Auger Boring Machine (ABM) in four separate headings; one heading from each of the tunnel end portals, and two from a shaft in the middle of the highway. To facilitate the auger boring operation, a custom steel reaction frame was required to counteract the thrust from the ABM at the portals, and a temporary shaft structure was installed in a narrow median space of the highway. The installation of the pipe canopy had to overcome challenges including removal of obstructions, alignment issues, and controlling settlements to the highway surface. This paper discusses the purpose of the pipe canopy, design and installation of the temporary shaft and structures to support the auger boring operation, the experience of the contractor during the installation of the pipes, and brief overview of the experience tunneling below the pipes.

Jun 13, 2021

By Robert H. Merrill

This report summarizes the first phase of studies to determine the design and behavior of an unsupported roof in an experimental room in limestone. The selection of a roof horizon and the design of the room were results of an investigation of the geology of the formation, the physical properties of samples from the proposed roof, and calculations from the theory of gravity-loaded beams. The design of the opening, some physical properties of the roof in place, and the behavior of the roof were checked by tests in a full-scale experimental room. The room was instrumented to measure roof deflection, separations in the roof strata, and incipient failure. The dimensions of the room before instrumentation was installed were 10 by 100 feet; the room was widened in successive increments to 40 by 100 feet. Between widening operations periods up to 6 months were allowed to provide a time test of the roof spans. The results of the measurements of deflection and separations showed that the lowest 6-inch layer in the roof became detached as the room was widened. This layer was eventually removed after standing without failure for about 4 months at room dimensions of 40 by 100 feet.

Jan 1, 1957

By Jianping Zuo, Chunlei Zhang, Yong Zhang, Shouyang Gao

To study the fracture evolution of overlying strata for ascending mining in a short-distance coal seam group, a two-dimensional physical simulation model was designed based on a specific geological condition. The fracture development zone was divided into the compaction zone and active zone by monitoring and analyzing the macro fracture evolution of the surrounding rock mass during the excavation of multiple coal seams. The secondary fracture development process of the overlying strata was demonstrated with a physical model. The quantity, length, and inclination of the fracture were calculated with MATLAB software, and the results were verified by geological radar. The total number of fractures between two coal seams increased with a “parabola” shape during the excavation of the lower coal seam, the crack angle was mainly vertical and horizontal, and the number of horizontal cracks first increased and subsequently decreased; the excavation of the upper coal seam caused the secondary fracture development process of the overlying strata, and the relief range and its extent increased. The mining-induced cracks from the lower and upper coal seams connected with each other, especially the permanent vertical fracture in the cutting room side and face side. Finally, the three-dimensional gas fissure was formed.

Nov 24, 2020

By N. W. Byrne

THE study of diamond drill results at the Lake Athabaska property of Athona Mines, Limited, and the co-ordination of information secured, has demanded extensive application of methods for interpreting true conditions, both structurally and from the point of view of ore outlook. This work was in charge of a capable engineer, who, as the result of exhaustive study of the drill cores, has been able to issue maps and plans exceeding the expectations of the majority of engineers and geologists who visited the field during the past summer (1935); that is, having in view the fact that staking of the property had been completed but a few months beforehand and that geological conditions were practically unknown up to the time drilling began in April. The following pages present an outline of the work of the assay and engineering offices in co-ordinating and interpreting the results of the drilling. The writer desires to acknowledge the suggestions offered by A.P. Beavan, geologist and engineer at Athona Mines, whom he assisted during the drilling campaign, and also the co-operation of the drilling contractor's employees. The geological map, mine plans, and forms accompanying the paper are from the Company's engineering office files.

Jan 1, 1937

By Z. Zhang

Aluminum boron carbide particulate reinforced composites have found new applications in nuclear industry due to their special capability to capture neutrons, Recently, Alcan successfully developed a liquid metal mixing process to fabricate Al¬B4C metal matrix composite instead of powder metallurgical technology. In the process, titanium is added into the composites to control interactions between boron carbide particulates and aluminum matrix, To understand the effects of titanium on the composites, the solidification microstructure of Al-16%B4C without or with titanium was examined by optical and electron microscopes. The results show that titanium can improve the uniformity of the particulate distribution within aluminum matrix if the titanium content in the composites is more than 0,5%, Furthermore, it is found that the layer with rich titanium on the surface of the particulates can limit the formation of AlB2 type compounds, which may greatly deteriorate the fluidity of the composites, In addition, it is also found that the amount of the reaction products in the composites increases with the increase of holding time. However, the rate of the increase is mitigated by the increase of the content of titanium in the composites. Besides, a procedure was proposed and implemented for the evaluation of uniformity of particulate distribution within aluminum matrix.

Jan 1, 2005

By Manchao He, Xiaoding Xu, Yubing Gao

Based on the geological conditions of the 15,600 working face in Pingba Mine, this paper establishes the mechanical model of the stress distribution in the pre-working face under the influence of mining pressure based on a hemispherical stress distribution theory. The analytical formula for the stress distribution is determined. A numerical model for the mining pressure under the influence of key layer is also constructed, and dynamic stress interruptions under various roof-cutting relief schemes in different horizontal positions are simulated. The stress distribution of the stope under different pressure relief schemes is analyzed and compared with the theoretical results. Results show that blasting roof cutting blocks the transmission of the abutment pressure to the working surface to the coal and rock mass in front of the working face, reducing the significant working face mining pressure influence range, which decreases as blasting pressure relief position moves toward the working face. Stress accumulation in the coal in front of the working face also increases as the blasting pressure relief position moves toward the working surface. Engineering practice results show that blasting cutting can effectively block the propagation of mining pressure, and the stress impact range is shortened by approximately 1/3.

Jul 31, 2021

By Sailesh S. Author

The current design method for soil-cement (SC) columns improved soft clayey ground under the highway embankments assumes a slip circle failure surface shearing through the columns and the soils using a weighted average shear strength. However, the results from the laboratory centrifuge model test and numerical analysis indicate that in many cases, the SC columns fail by bending. Some researchers have proposed methods for estimating the maximum embankment loading for bending failure of SC columns, but those methods have limitations in correctly considering the internal shear stresses or not applicable for the group SC column improvement. Numerous model embankments on SC columns have been simulated by three-dimensional (3D) finite element analysis (FEA) and the mechanism of bending failure and the magnitude of the bending moment in the SC columns under embankment load has been investigated. Based on the simulated results, the design method for the estimation of the bending failure of floating SC columns has been proposed. The predicted results from the proposed method agreed with the existing field condition of one embankment in Saga, Japan reported in the literature in terms of the stability of columns. Hence the proposed method can be used for the design of floating SC columns in the soft ground.

By Y. Kashiwaya, J. Yagi, P. R. Austin

The problems of global environment and resources have become important issues in recent years, and the iron and steelmaking industry is requested to decrease energy consumption and carbon dioxide emission. The improvement of efficiency of ironmaking system is one of the countermeasures for these problems because more than a half of total energy input to the integrated steelwork is input to the ironmaking system. Various approaches to improve the blast furnace process have been made. The authors examined their performances through mathematical simulations of blast furnace operation, and confirmed the improvement of blast furnace efficiency under some operating conditions. The ironmaking system consists of various processes, and the materials and the energy are transported among these processes. Thus it is necessary to evaluate the efficiency of the novel operation of blast furnace based on the ironmaking system. In this study, the balances of material and energy on ironmaking system that consists of blast furnace, coke oven, sintering and hot stove processes were analyzed. The operation status of each process in the system was adjusted according to the results of the operation simulation of the blast furnace under novel operating conditions. The analysis clarified the effect of the blast furnace operation on the energy balance and CO2 emission of the ironmaking system.

Jan 1, 2015