Search Documents

By R. S. Cartwright

Two types of automatic drilling controls, the Halliburton and the Hild, are now available and are coming into more or less general use in deep drilling. The primary function of both is to maintain a safe limit of torque on the drill pipe, this being accomplished by automatically controlling the weight or pressure on the cutting tool. Neither type will necessarily increase drilling speed, but by permitting advantage to be taken of "breaks" in the hole higher average cutting speed may be maintained. The control is essentially a safety device, and should be considered as such. It is not the purpose of this paper to discuss the merits of drilling controls, although the advantages over manual feed at the brake drum are obvious, but rather to point out some of the limitations. The Halliburton Control The Halliburton control is designed to operate during drilling through the agency of the draw works. Automatic and constant control. of the torque on the bit is governed by clutches on the control itself, and the line shaft to drum shaft drives on the draw works. In operations other than drilling the control is simply a jackshaft between prime mover and draw works. It is, of course, adaptable to any type of power. Because control of the torque on the bit is dependent upon the various ratios or clutch combinations available on the Halliburton control and the draw works, it follows that there are certain limitations in points of control. Table 1 shows the possible ratios which can be obtained with the control and a popular type of three-speed draw works, it being assumed that the highest possible gear combination-the combination which when engaged will suspend the least amount of weight-has a value of 1.00.

Jan 1, 1928

By Roger G. Haga, Richard P. Campbell

Introduction Project scheduling . . . . • What is it? • Why is it done? • Who does it? • How is it done? • When is it done? These are some of the questions that will be addressed in this paper. It is intended that by exploring these questions, an understanding of project scheduling, its purpose and benefits can be achieved. The purpose of this article is not to describe in detail "how to schedule", but rather to give an overview of the scheduling function on a project. A successful scheduling effort is dependent upon the people responsible for developing, implementing, and monitoring the schedule, and the tools and procedures that are used. These three elements are integral components of project scheduling. What is it? A schedule is the integration of network relationships, resource constraints and the calendar. The schedule identifies when the activities "will" be done, while the network states when they "must" be done. Networking techniques are the most widely accepted scheduling tool for complex projects. The benefit of the network is the simplicity in illustrating, presenting and analyzing the dependency relationships of a project. The logic network is the foundation of the schedule. When calendar dates are applied to the logic network, it becomes a schedule which provides the basis for evaluation of project status, forecasting the occurrence of events and controlling the project. The sequence of activities that requires the longest time to complete determines the overall duration of the schedule. This longest sequence of activities is called the "critical path". The "critical path method" (CPM) is used to describe this particular schedule network methodology. The two common conventions of CPM networks are the "arrow diagram met hod" (ADM) and the "precedence diagram method" (PIM). There are arguments in favor of each of these two methods, and usually the one that is used is a matter of personal preference, project directive or corporate procedure.

Jan 1, 1986

ONE of the problems that confronts the chronicler of the Porphyry story is to determine the date from which Morenci should be regarded as one of the group. The mines have the distinction of being the first operated in Arizona for copper. A small smelter was in operation as early as 1873 and in the eighties two smelters accounted for a substantial production ranging from 3,000,000 to 6,000,000 lb. per year. The first concentrator was built in 1886, but the ores were principally oxidized, and direct smelting ore still supplied most of the production. As early as 1893, the mining of somewhat leaner porphyry ores, containing copper in the form of the sulphide mineral, chalcocite, was commenced; but these still were of comparatively high grade and the concentrators were plants of 100 to 400 tons daily capacity. Moreover, the backbone of operations was still the production of rich oxidized ores for direct smelting. They assayed 10 to 15 per cent copper and the sulphide milling ores assayed 3 to 4 per cent. A significant comment appears in the Copper Handbook for 1908. Speaking of the Arizona Copper Co., Ltd., which was to become the most important component of the present Morenci enterprise, the editor, Horace Stevens, says: "A tremendous amount of ore is in sight, ore reserves . . . being estimated at 10,370,600 tons . . . " It seems fair to infer from this that the property was not yet regarded as an immense low-grade mine, but that the copper content of perhaps 70 lb, to the ton made an ore of "medium " grade even according to the standards of the time. Although the concentrating ore was typical of that in the porphyry group of mines (except for its greater richness), no one seems to have the least inclination to take from Utah the

Jan 1, 1933

By Dale S. Preece

A carefully designed and controlled in-place destruction experiment was performed on a concrete bunker buried in 4.27 m (14 ft.) of soil. The objective was to determine if the explosive charges would collapse the structure in-place without requiring mechanical excavation. Collapse of the buried structure was fi rst attempted by drilling holes in the soil and placing four 13.38 Kg (29.5 lb) Comp B explosive charges at a depth of 2.13 m (6.7 ft.). The confi guration of the charges when detonated was 2.13 m (6.7 ft.) off the top of the concrete roof and 3.66 m (12 ft.) apart in a square pattern. Detonation of these charges created a crater ~4.88 m (16 ft.) in diameter and 2.13 m (6.7 ft.) deep, leaving ~2.13 m (6.7 ft.) of soil covering. Very limited spalling occurred on the ceiling of the concrete structure as a result of detonating these four charges. The second attempt to collapse the structure consisted of placing another single 13.38 Kg (29.5 lb) charge, identical to the fi rst four, near the geometrical center of the bunker roof. This charge was detonated in the soil cover 100 to 200 mm (4 to 8 in.) above the reinforced concrete roof, collapsing it. Due to the collapsed roof and remaining soil cover, the structure had been collapsed in place, requiring no further demolition. A computer simulation of the above explosive destruction scenario was completed using the computer hydrocode AUTODYN with a granular material model to treat the soil and the RHT brittle material model to represent the concrete. AUTODYN accurately recreated the scenario including the slightly damaged response of the concrete structure to the initial four charges and the collapse of the structure resulting from the second single charge close to the roof.

Jan 1, 2007

By John Mastoris, Kostis Dragasakis, Kostas Kouklidis, Shkurtë Gashi, Halil Berisha, Jenuz Bulica

Titan Group’s environmental policy and Sharrcem’s Corporate Social Responsibility (CSR) are the driving forces behind the development and implementation of a comprehensive Rehabilitation Plan at Dimce Quarry, which is the main raw material source for Sharrcem Cement Plant since the 1970’s, located in the municipality of Hani i Elezit in Kosovo. Based on an Environmental Impact Assessment Study and the approved Mining Plan and also on the principles prescribed in the Guidelines on Quarry Rehabilitation, released by the Cement Sustainability Initiative of the World Business Council for Sustainable Development (WBCSD-CSI), Sharrcem has adopted a quarry operation and rehabilitation process in line with the best practices in the mining and cement sector. This paper discusses the background for the development of the rehabilitation plan and the results of rehabilitation activities, as have been implemented over the last few years. The main objective of the progressive rehabilitation plan at Dimce Quarry is to restore the depleted pit and return it back to the original land owners for resettlement. To date approx. 3,4Ha of former mining area has been restored by backfilling and levelling of the depleted closed pit and returned back to owners, who have built their houses and turned it into a living area again. This Quarry has turned out to be a real composition and practical example of preserving and returning back the natural resources in a state compatible with the surrounding environment and with respect to the needs of the local stakeholders. The motivation for business to engage in rehabilitation activities in the first place lies in the belief that the development and implementation of a progressive and practical Quarry rehabilitation plan and restitution of the land will deliver significant environmental and social benefits that outweigh the long-term rehabilitation costs, while maintaining the company’s reputation.

Jan 1, 2017

By Aly M. Mohammad

Croton Point Avenue Bridge carries Croton Avenue over Metro-North main tracks at Harmon Rail Yard in Westchester County, New York. The new bridge is 1100 foot long and 36 foot wide nine span structure with three spans continuous units. The spans are steel multi-stringers, composite with concrete deck. The piers are solid wall piers and the foundations are spread footings. During the design of the bridge foundations it was determined that the relatively loose to medium dense sand layer is susceptible to liquefaction under a design earthquake with a seismic coefficient of 0.15g. Several foundation options were considered for the new bridge including both shallow and deep foundations. It was determined that the most cost effective alternative is to use spread footing foundations supported on densified soils. Vibratory probes were utilized to densify the loose to medium dense sand layer and reduce the risk of liquefaction. Densification test sections were performed to determine the optimum spacing for the vibro probes. The test sections included performing piezocone tests before and after the densification to compare the increase in relative density of the sand. In addition, ground surface settlement due to the vibro probes was measured and correlated to the increase of soil relative density. The paper will present the results of the ground improvement method utilized and correlate the spacing of the vibro probes and the increase in relative density and the results of the piezocone tests performed before and after the densification. It was found that the vibro probes are not as effective as thought at shallow depth below the ground surface. It is believed that the results and finding presented in this paper will benefit both the design and construction industries by providing a relatively cost effective means to improve the soils

Jan 1, 2007

By G. D. Bengough

CORROSION tests should be designed so as to facilitate as far as possible the interpretation of results, consequently factors which may affect the rate of corrosion should be controlled as far as practicable, and very full data should be given regarding the conditions of the test. Among the most important factors affecting the rate of corrosion is often the rate of supply f oxygen to the metal surface. It is essential therefore to understand the mechanism by which oxygen is transferred from the liquid surface to the surface of the metal. The work of Adeney and his coworkers has thrown much light on this mechanism. They have shown1 that the aeration of deaerated water and salt solutions proceeds much more rapidly than can be accounted for by mere diffusion, and have suggested that downward "streaming" takes place from the surface of the water, due mainly to an increase of density brought about by evaporation. The evaporation reduces the temperature of the surface layer, and also increases the concentration in the case f salt solutions. The effect of evaporation in facilitating the transfer of oxygen to a metal and increasing the corrosion f the metal was shown in some experiments due to Friend .2 He tested the corrosion f mild steel plates immersed in water in glass jars, a steady stream f air being drawn over the surface of the water in the jars. The air passing through half the number f jars was saturated with moisture, that passing through the others was dried with calcium chloride. He found that "in every case the water exposed to dry air was approximately twice as corrosive as that exposed to air saturated with water vapor."

Jan 1, 1929

By C. W. Goodale

THE motives behind the organization of the Bureau of Safety were twofold. First, there was the policy of the company toward its employees, which was one of fairness and consideration for their welfare and which entails the prevention of injuries; second, in order to prevent injuries, a study of their causes was essential, and this study could be made only by a thorough systematic classification of accidents, which required a special department to form and carry out the plans. The Bureau of Safety was organized to begin operation Jan. 1, 1914, but practically all of the first year was spent in collecting data, making plans, etc. This department is semi-independent of others and reports directly to the president and general manager. It consists of the president of the company and the managers of the following departments: Mines, Washoe Reduction Works, Great Falls Reduction Works, Coal Department, Lumber Department, B. A. & P. railway, and the chairman of the Bureau of Safety. Working under this group is the General Safety Committee consisting of the manager of mines, as chairman, the general superintendent, two assistant general superintendents, and the heads of the following departments: mechanical, geological, purchasing, sampling works, and framing plant, as well as the safety engineer. Operating under the General Safety Committee are the group safety committees, consisting of the Anaconda group of mines, Boston & Montana group of mines, zinc group of mines,.Washoe reduction works at Anaconda, B. & M. reduction works at Great Falls, coal department, lumber department and the B. A. & P. railway. Each of these group safety committees was in charge of the superintendent or manager of the group represented and the committee consisted of the foremen of the mines or works that the committee served, as well as the safety engineer.

Jan 2, 1922

By Paul Kunze

When a new bridge was needed across the upper reaches of the Yellowstone River in Montana, removing the old concrete bridge piers became an environmental concern for the highway department engineers. The location is about fifty miles downstream from the north edge of Yellowstone Park. The determination was made by the federal and state agencies charged with protecting the resource, that the old piers had to go but the river bed had to remain unchanged. Concerns were expressed that removing the concrete presented the potential for environmental damage to this protected portion of the river. These concerns prompted the state to place stringent restrictions on the contractor in the way they carried out the demolition and disposal of the piers. The reinforced concrete masses had to be removed to an elevation at least fifteen feet below the river bed and every bit of concrete debris had to be removed from the river channel. Explosive removal was discouraged, but the only other options: saw cutting, mechanical or chemical breaking, were not viable.

Jan 1, 2014

By George M. Enos, Robert J. Anderson

An impoRtant factor affecting the rate and nature of corrosion of metals and alloys is the film, or coating, formed on the surface; and this may accelerate or retard corrosive action once started. The formation of films and coatings is intimately associated with the chemical composition and physical constitution of both the metal and the corroding medium. A film or coating may be either the corrosion product resulting from oxidation; that is, an oxide or salt, or a deposition of suspended matter from the corroding media upon the surface of the metal, or a mixture of both. The coating may adhere tightly or loosely to the surface of the corroded metal. In short, a film or coating is the reaction product of the corroding medium and the metal, which adheres to the surface of the metal and with which may be intermingled material from the attacking media not concerned in the chemical reactions. As the terms film and coating are used by different writers for very different things, distinction is made between the two, by the present writers, on the basis of thickness. Thus, a film is defined as a corrosion product or deposition, on the surface of a corroded metal, that is of such thickness that it cannot be measured by the metallurgical microscope. A coating, on the other hand, is of such thickness that it can be measured. If the resolving power of the 2-mm. (equivalent focal length) apochro-matic oil immersion objective (N.A. 1.4) is taken as the limit of the microscope, the limiting resolution is two lines that are 0.0002 to 0.0004 mm. apart. It is thus possible to measure coatings that are greater than 0.0002 to 0.0004 mm. thick. This thickness is equivalent to 50,000-

Jan 1, 1925

By S. Le Fevre

THE application of electricity to the mining and beneficiation of the magnetic iron ores of the Mineville, N. Y., district, on Lake Champlain, has resulted in economies and enhanced quality of product, without which only a comparatively small quantity of the present output could be marketed. The output of the Witherbee, Sherman & Co. mines is about 700,000 tons per annum, and of this about four-fifths is treated by magnetic separation to increase the iron content and reduce the phosphorus. The use of electricity for the magnetic separation of the ore from the gangue is therefore of primary importance, and makes possible the application of electric power for mining and preparing the ore for concentration: The fact which speaks loudest in favor of the application of electricity is this: It is possible for about 25c. per ton of shipping ore to furnish all the power required to put the ore on cars. This includes mining a hard ore underground, from a depth of 900 ft., hoisting to surface, crushing to 4 or s in. in size, and separating from the gangue. This also includes lights about the works, and all miscellaneous power, such as about the shops. The first plant for the generation of electric power for use at Mineville was completed in 1903, and was one of the first for the application of electricity to mining iron ore. This was a Nordberg compound condensing steam engine, direct connected to a 750-kw. alternating-current generator, 3,300 volts, 3 phase, 25 cycles. All the plants added later use the same-current but with higher voltage. The map, Fig. 1, shows the power plants and the transmission system; Figs. 2 and 3 are views of the shaft houses and the mills.

Jan 6, 1914

By Simon Ash

THE coal-mining districts of Washington are mainly west of the Cascade Mountains; Fig. 1. The mines are on the foot hills of the slope, the lignite fields of Lewis and Thurston counties extending into the valleys west of the mountains. An exception is the Roslyn field, a small but important area on the eastern slope. If western Washington is divided into three areas from north to south, the bituminous coal fields and most of the active operations will be found largely in the middle area. The southern portion contains lignites over a large area. In the northern portion, mining is practically restricted to one mine, the Bellingham, which is working a subbituminous coal seam near the city of Bellingham. The degree of alteration that the coal of a particular field has undergone may be gaged roughly by the position of the field with reference to the Cascade Mountains. The lignites of Tenino, Tono, Mendota, and Castle Rock, on the railway line connecting Seattle and Portland, occur in a region, of low relief, in which the Eocene coal measures have suffered only minor disturbances. Subbituminous coals occur in the foot hills, as at Renton, Newcastle, and Bellingham. Coals high in fixed, carbon are found nearer the mountains, where. the measures have been sharply ,tilted and folded, as at Black Diamond and Carbonado. The two typical anthracite fields are located still higher, in the rugged mountains where outcrops appear both in deep gorges and on ridges at elevations approaching 5000 ft. At. Carbonado is found the only semianthracite seam worked on a commercial basis. The occurrence of this seam in a region of bituminous coal is due to the nearness of an igneous sill, which has changed its character from bituminous to semianthracite.

Jan 3, 1925

By Henry Rawdon

Cold-working is generally considered as a process of hardening metals. Diamet-rically opposite statements concerning the applicability of the scratch-hardness method in the testing of cold-worked metals, particularly after severe deformation, which exist in the technical literature led to the study of the results which are summarized in this paper. A series of metals, of which copper, iron and tin are used as illustrations here, were cold rolled to a definite degree without any intermediate annealing and the hardness determined by both the scratch and Brinell methods. The results indicate that the metal hardens rapidly during the initial stages of deformation; however, after a certain stage, which corresponds to a rather definite microstructure, the metal becomes softer and in its final form may be softer than the metal in its initial stage. As part of the study of the scratch-hardness method for metals and alloys in cooperation with one of the technical committees of the American Society for Testing Materials, the authors devoted considerable time to the study of the changes in hardness of metals when cold rolled. Various seemingly contradictory statements in the technical literature concerning the applicability of the scratch-hardness method to such cold-rolled materials were among the principal reasons for the investigation, the results of which are in part presented here. The effect of cold deformation, at least in moderate degrees, on the hardness as measured by the Brinell and other common methods is so well known that further reference is unnecessary. Concerning the scratch hardness of cold-worked metals, Martens and Heyn state' that hardness, whether measured by the ball-pressure method (Kugeldruck) or by the scratch method (Ritzverfahren), will be increased by cold deformation. Jeffries and Archer give a seemingly diametrically opposite view. They state,2 that "the sclerometer (indicating scratch

Jan 1, 1924

By T Muri

The drying operation of materials from particulate solids, through slurries and suspensions, to continuous sheets represents an important part of several processes in the chemical and mineral industries. The increasing demand of high productivity at low cost and minimal environmental impact makes it complex to evaluate and choose the best available drying technology for each industrial application. The drying technologies are mainly characterised on the basis of how the wet product is related to the drying medium, namely: direct and indirect drying. In the direct drying method (convection drying), the product is brought into direct contact with the drying medium, which may be hot gas or air. Large quantities of gas are necessary for transfer of the required energy. A special case of the direct dryer is the fluid bed dryer, in which the product floats on a cushion of air or gas. The process air is supplied to the bed through a perforated distributor plate and flows through the bed of solids at a velocity sufficient to support the weight of particles. Very high heat and mass transfer values are obtained as a result of the intimate contact with the solids and the relative velocities between individual particles and the fluidising gas. In the indirect drying method (conduction or contact drying), the wet product is separated from the drying medium. The drying unit can consist of a rotor forming the indirect contact heating surface mounted in a stationary or rotating shell. The indirect method uses saturated or superheated steam resulting in low energy consumption and minimal environmental impact. In this paper, a review is given of the technologies available on the market based on different drying methods. The advantages and the disadvantages are summarised with respect to issues such as investment and operating cost, maintenance, product capacity, product handling and environmental impact.

Jan 1, 2006

By H. B. Smith, B. Egererg

In a previous paper1 the authors dealt with the physical properties of cold-rolled and heat-treated Britannia metal of the approximate composition Sn, 91 per cent., Sb, 7 per cent. and Cu, 2 per cent. It was found that cold rolling to more than 50 per cent. reduction produced a continuous softening of the metal when measured by the Brinell machine, whereas the Shore instrument indicated increased hardness; that the strength of the material followed the Brinell hardness and that the metal therefore became weaker the more it was cold-rolled; and further, it was found that hardness and strength could be largely restored to the cold-rolled metal by "baking" for about one hour at any temperature between 200" and 450" F., the melting point. The higher the baking temperature, the more effective was the heat treatment as far as increased hardness was concerned. It seemed to be of little importance whether the metal was soaked or not at the baking temperature for a great length of time and the rate of cooling seemed to be immaterial. The present paper deals with the same alloy and more particularly with the resistance towards various forms of stress — tensile, bend and deep drawing. The metallography of Britannia metal has in part also been covered and an explanation attempted for the abnormal behavior of this alloy. Tensile and Bend Tests Two ingots 73/4 in. wide, 11 in. long and ¾ in. thick were cast from the same pot. One ingot was cold-rolled in one direction to a strip 0.241 in. thick, which furnished the tensile test specimens; the other ingot was rolled in the same way to 0.253 in. and furnished the specimens for the bend tests. The ingots were cast as described in the previous paper and cold-rolled in six passes.

Jan 1, 1930

By T. D. Yensen

I. INTRODUCTION IT is safe to say that of all the different materials that go to make up electrical machinery, iron is the most important. Upon its -magnetic and electrical quality depends not only the efficiency of the machine but, to a very large extent, the cost. Aside from the mechanical strength, there are three characteristics of iron that are of importance in this connection, viz., magnetic hysteresis, electrical resistance, and magnetic permeability. In the homopolar machine, where the magnetic flux is unidirectional, permeability is the only important factor, but in all other machines the flux is reversed in one or more parts and causes losses due to hysteresis and eddy currents. The eddy-current loss depends largely upon the electrical resistance of the iron; the higher the resistance the lower the loss, under otherwise identical conditions. These hysteresis and eddy-current losses cause heating of the machine, and as they depend upon the magnetic density in the iron, this density must be regulated so that the heating shall not be excessive. If the hysteresis and eddy-current Josses and the permeability of the magnetic circuit will permit an increase in the magnetic density, or, in other words, a decrease in the amount of iron, this in turn will mean a decrease in the amount of copper needed, with a consequent decrease in the copper loss. It is thus seen that; indirectly as well as directly, the above characteristics have an important bearing on both the efficiency and the cost of electrical machinery. In general, it may be said that iron for electrical machinery should have the following characteristics: (1) low hysteresis loss, (2) high electrical resistance, and (3) high permeability. These are the characteristics that investigators have been striving to attain since electrical machinery first came into use.

Jan 2, 1916

By A. C. Richardson

During the past two and a half years the U. S. Bureau of Mines and the University of Alabama, with the cooperation of the different coal operators, have been making an extensive study of coal preparation in the State of Alabama. Considerable time has been devoted to the study of the washing characteristics of the Mary Lee bed and the various methods used in preparing from it a low-ash coal suitable for the manufacture of metallurgical coke. One of the phases of this problem is the utilization of middlings products from the washing plants. This paper gives the results of treating jig middlings on a coal-washing table at the Bureau of Mines laboratory at Tuscaloosa, Ala. The sample used was secured from the Sayreton washery Of the Republic Steel Corporation, Sayreton, Ala.

Jan 1, 1931

By L. Chanderman, C. E. Dohm

"Mineral Resource estimation (MRE) and classification are highly dependent on the confidence in the model of the orebody geometry, known as the geological model, within which the estimates are constrained. An understanding of the geology of a deposit is thus fundamental to the Mineral Resource evaluation process. The geological model is a function of the structural and depositional complexity of the geology captured by drilling information, which is limited in the early stages of a project. The information effect has a significant impact in terms of the interpretation of the geology as well as the estimation of grade continuity and the resultant risk associated with the Mineral Resource estimate and classification.Therefore, as new drilling information becomes available, it is necessary to update and refine the geological model to appropriately constrain the resource estimates. The grade information is also updated, including statistics and the spatial correlation characteristics. This refinement is based on geological interpretations derived from the drillhole information that becomes available throughout the life of the mine; orebody knowledge that comes from working experience of the deposit, as well as familiarity with the software package used for modelling, is also important.In updating, the potential to identify new resources in previously unknown areas may be realized. The opposite may also occur where previous interpretations of ore continuity are refuted. Both scenarios could result from a better understanding of the geology of the deposit and thus a more realistic MRE, which reduces geological risk. This paper describes how newly drilled advanced grade-control holes for a gold deposit in Mali were used to refine the 3D geological model for the deposit in an attempt to identify the potential for additional oxide ore using conventional geostatistical evaluation techniques."

Jan 1, 2017

1. Scope of project In South Australia, the Western Mining Corporation operates the underground copper and uranium mine Olympic Dam. The deposits concerned are enormous (approx. 570 million tons) and have been mined since 1988. At the end of 1996, Western Mining decided to increase the capacity of Olympic Dam from 85,000 t.p.a. to 200,000 t.p.a. Planning At this point, SIEMAG-GHH Mining Division was asked to carry out a study including the planning of the entire shaft hoisting operations and calculation of the investment and operating costs involved. With the assistance of Australian partners, the study was completed within a single month. The principal points of the study were as follows: ? Planning of the hoisting machinery for 1,375 tons per hour from the surge bin below ground to the discharge bunker above ground. ? Optimisation of the hoisting operation with regard to maximum availability and safety. ? Optimisation of the time schedule to minimise the financing costs of the investment. ? Statement of the investment and operating costs. ? Comparison of the technical data, design and availability of the planned machinery with reference plants. Construction of the plant Following acceptance of the study, the decision was taken within a few weeks to implement it. SIEMAG Transplan GmbH received the order to execute the entire shaft hoisting machinery on the basis of the study submitted. The decisive factors in placing the order were: ? Convincing study, adherence to schedule ? Reference to comparable plants elsewhere ? Reference with regard to availability.

May 1, 2003

By N. W. Lord

The process of molten-zone refining is analyzed for long ingots and many zone passages. Formulas are derived which give the resultant impurity distribution in terms of finite series. A comparison with the approximate procedure of Hamming is given. HE physical principles and applications of an extremely physicalprinciple efficient form of metallurgical refinement has been described by Pfann. The purpose of the present paper is to describe a method of analyzing exactly the particular program used which enables the segregation effect to be predicted for any number of molten-zone passages in a long ingot. The method is applied to the particular case of refinement of an ingot whose impurity initially is uniformly distributed throughout its length. A number of molten zones of equal length are passed through the ingot effecting a radical redistribution of impurity. Pfann has indicated an approximate method, due to R. W. Hamming, of calculating the resultant concentration after each successive zone pass for a particular value of the segregation constant defined in his paper. Here a solution will be presented in terms of the number of zone passes and the segregation constant. The expression, though cumbersome, is exact and susceptible to ordinary numerical computation procedures. The results of a similar computation using the procedure of Hamming are presented in a table together with the exact results of the present method. The discrepancy in terms of absolute concentrations is tabulated for the first eight zone-lengths. To establish the notation (which follows that of Pfann1 as closely as possible) and physical basis of the analytical equations, the physical model and principal assumptions may be reviewed. An alloy of two elements, where there is formed a continuous range of solid solutions, usually does not melt as a simple compound. Rather, a temperature is reached where the solid solution is in heterogeneous phase equilibrium with a liquid solution of different composition. The temperature dependence of these equilibrium compositions forms part of the phase diagram. For very small concentrations of a solute B in a solvent A, this usually takes the form of Fig. 1. Sometimes the solidus and liquidus slope upward. This corresponds to a segregation constant (defined below) which is greater than unity. The segregation constant is now defined as k = Cn(x)/CnI(x) [1] where C,,(x) is the impurity concentration in the solid ingot at distance x during the nth passing of a molten zone and Cnl (x) is the impurity concentration of the liquid zone from which the solid at dis- tance x is formed (see Fig. 4 of ref. 1.) C (x) remains the same after passage of the zone. The constant k may be either greater or less than unity in general. Purification in the former case is effected only in a finite ingot and in the portion that is melted last. For k less than unity purification is effected even in an infinite ingot. The method which follows gives, in the former case, the successive increases in impurity concentration and, in the latter case, the successive decreases in concentration. The general case of impurity redistribution will be considered first, and purification will be discussed later on. The analysis rests on the following assumption: The movement of the zone is too rapid to allow appreciable atomic rearrangement in the solid sections and too slow to disturb the uniform impurity distribution in the liquid zone characteristic of equilibrium. Hence, the composition in the solid at the left solidifying interface will be determined by Eq. 1 while the impurity concentration of the liquid zone will be uniform throughout its length. The reasoning which follows closely parallels that of Appendix 11 in Pfann&apos;s paper. It is reviewed here for the case of the nth zone pass in order to make clear the meaning of an operator essential to the present method. Fig. 4 of ref. 1 shows the movement of a molten zone of length 1 in an ingot of total length d. Each Cn(x) can be determined from the condition that the amount of solute added to the zone during an incremental advance, dx, is due to the melting in of a solid portion C(x)dx and the freezing out of kCnl(x), that is d I —r- CnL (x) dx = Cn-1 (x+l)- kCnL (x) dx or, in terms of Cn(x) d k k —— C,(x) +—c.(x) =— Cn-1 (x + l). [2] dx l l This, of course, is derived from the main assumption, the fact that 1 is constant, and that the total impurity content previously present up to x + 1 is constant . A correction has to be made for the region (d — nl) < x < d. This is due to the zone length changing during the passage of the solidifying interface beyond x = d — 1. Since the general solution would be too complicated otherwise, only the region 0 < x < d — nl is considered. The general solution of Eq. 2 is

Jan 1, 1954