Search Documents

By Jerome and Strauss, Carl L. Shapiro

This is a critical examination of the theory that the amount of carbon necessary to form the iron-carbon (carbide) eutectoid is lowered by the addition of any carbide-forming element. Although this theory has been built up over a long period of years, it appears, in the light of recent published investigations upon the ternary constitutional diagrams of iron with carbon and other alloying elements, to be no longer tenable. A survey of these new results, summarized below, shows that (as is known) some metals lower the carbon content of the iron-carbon (carbide) eutectoid, whereas others raise it, but (as not heretofore clearly set forth) some first move the eutectoid in one direction and then, at higher concentrations, shift it in the opposite direction. Moreover, these differences in behavior exist even among the common alloying metals classed as carbide formers. PART I Influence of Body-centered Cubic Elements The effects of the various body-centered cubic metals (chromium, tungsten, molybdenum, vanadium, columbium and tan. talum) are reviewed individually. Iron-carbon-chromium System.—In the monograph on Alloys of Iron and Chromium, Kinzel and Crafts1 concluded that the carbon content of the eutectoid is lowered by increasing the chromium content. The quantitative influence of chromium on the eutectoid point of iron-carbon alloys was shown by Monypenny2 (Fig. I) and no data have been forthcoming to refute his findings. Iron-carbon-tungsten System.—Gregg,3 in the monograph on Alloys of Iron and Tungsten, accepted the data showing that tungsten decreases the amount of carbon required to form the eutectoid. The influence of tungsten on the eutectoid percentage of carbon as determined by Oberhoffer and Daeves4 is shown in Fig. 2; these results have received general approval. , I ron-carbon-molybdenum System.—In the monograph on Alloys of Iron and Molybdenum, Gregg5 reviewed the work of Guillet,6 Swinden,7 and ReedI8 all showing that molybdenum lowered the carbon content of the eutectoid, whereas Takei9 contradicted this conclusion. Svetchnikoff and Alferova,10 a little later, showed that large additions of molybdenum shift the eutectoid to the right. These last-named investigators found that molybdenum, up to 1.2 per cent, shifts the pearlite point and the point of maximum solubility of cementite in the gamma phase only slightly in the direction of lower carbon content; on the other hand, increasing amounts of molyb-S

Jan 1, 1944

By Simon C. Dominy, Ian M. Platten

"Abstract - Gold-bearing quartz reefs commonly show extremely erratic and unpredictable grade variation, although gross geological continuity may be good. This type of variation is often described as being nuggety or having a high nugget effect and can be measured quantitatively using the semivariogram. Understanding of geological features such as reef texture and structure will provide improved models for the interpretation of assay data, drill core descriptions, etc. In this paper, a case study from the quartz-hosted gold occurrences in the Gwynfynydd mine, United Kingdom, is described. The work provides a starting point for models of lateral variation and demonstrates the types of structural and textural features that may be sought to give clues to the prediction of gold distribution in similar deposits. Gold deposition at Gwynfynydd is primarily associated with the reef footwall. The host veins form a discrete group of structures that may have been emplaced early in the sequence of quartz veins forming the reef. This potentially exposes them to a maximum number of dissection events during repeat dilations of the lode. Gold was deposited in the local porosity at extreme concentrations, equivalent to kg/t grades, when the host fissure had become filled with a porous framework of crystalline quartz and sulfides. Distribution of porosity varied laterally along the vein as the result of the formation of clump-like growths of minerals from the vein walls. The growth style is relevant to the distribution of gold although it may not be relevant to the occurrence of gold in a particular vein. The preservation of pores with some connectivity late in the vein fill sequence may be important in permitting continued but slow fluid flows. This facilitates effective fluid reaction with wall rock-derived methane, thus changing the relative rates of gold and quartz deposition in favor of gold. The textural studies explain the first-order control of nugget distribution at Gwynfynydd but do not allow for prediction and optimization of the resource estimation process. This is principally because of the very low geological continuity and poor predictability of the high-grade pockets. Nonetheless, the work does provide a clear geological explanation for the erratic nature of the gold. It indicates textures and structures that can be used to determine geological continuity of the goldbearing elements within the gross reef envelope."

Jan 1, 2001

By T. J. Close

On September 10, 1991, Secretary of the Department of Interior Manuel Lujan deleted the Silver Peak Range North Wilderness Study Area from the list of U.S. Bureau of Land Management lands in Nevada to be considered for wilderness designation. This decision was based in part on the U.S. Bureau of Mines mineral investigation of the wilderness study area which found that it has indications of precious metals resources. The following is a summary of the results of that mineral investigation. The study area lies between the Silver Peak and Dyer mining districts of west-central Nevada. The Silver Peak mining district, to the east, has a long mining history dating back to 1907 when precious-metals-bearing veins were discovered. The major producer in the Silver Peak district was Sunshine Mining Company's Sixteen-to-One silver mine. During the Bureau's study the Sixteen-to-One mine was operating; it has since been idled due to low silver prices. Precious metals-bearing veins were discovered in the Dyer district, to the west of the study area, in the 1860's. Mineral activity in Dyer district consisted mainly of prospecting. The Silver Peak study area itself has no mining history and contains only a few mining claims, but the Bureau examined 13 mineralized sites, most previously unknown and unclaimed. These sites are along two zones that cross the study area from the Silver Peak to the Dyer mining district. The two zones transect a volcanic center of fractured and altered rocks that contain epithermal veins of quartz, calcite, and jasperoid with gold, silver, and base metals. At the surface these veins are poorly defined and poorly mineralized. The more than forty veins examined in the study area are as thick as 17 feet and as long as 1,000 feet. Samples from surface exposures of these veins contained as much as 0.02 ounce per ton gold, 2.1 ounces per ton silver, 1.0 percent copper, 2.6 percent lead, and 0.4 percent zinc. Analyses of the Bureau data disclosed no vein large enough or of high enough grade to be classified a mineral resource. However, most do have indications of silver-and gold-bearing resources at depth. Subsurface exploration had to be done on the vein at the Sixteen-to-One mine to outline reserves (a vein averaging about 22 feet thick and containing 6-to 7-ounces per ton silver); the same is true of veins in the Silver Peak Range North Wilderness Study Area.

Jan 1, 1993

By Nilmara Dias, Maria Margarida Martins, Maria Teresa Carvalho

"The heavy residual fraction of the mechanical and biological treatment (MBT) plants treating undifferentiated municipal solid waste is mostly composed by inert materials, such as glass, stones, ceramics and brick. Glass, appearing in significant grade and amount, is not recycled today due to the high content in the other materials, mainly stones. All these materials have approximately the same density but stones have significantly different shape from other materials particles. In this paper it is presented the research developed to eliminate stones appearing in the fine fraction (2.8-8 mm) of the MBT plants heavy residual fraction (MBTr) using a shaking table operated in dry conditions. Two different samples from two different MBT plants were used. Firstly, the samples were characterized (materials content and particle size analysis). Then, laboratory work was carried out to optimize the operation of the shaking table, by changing the machine parameters, deck slope and movement frequency. The study showed that it is possible to upgrade the product in glass. The best results, obtained with one single stage of processing, were 82% content in glass with 84% in recovery, in the glass concentrate, when the coarser fraction (-8+5.6 mm) of one of the MBT plants was used. With the intermediate particle size fraction (-5.6 + 4mm), the glass concentrate attained 74% content in glass with 91% recovery."

Jan 1, 2014

By Goran Mathisson

In several investigations the correlation has been studied between the fuel consumption and the reducibility of the charged material in the zone of indirect reduction in the blast furnace (1, 2, 3, 4, 5). It has been found that increased reducibility allows greater gas utilization which accordingly lowers the fuel consumption. In direct reduction units this relation has not yet been fully established partly owing to the lack of accurate test methods and experience with different materials as regards reducibility. However, since the production rate in a direct reduction unit is closely related to the time required to reach high degrees of reduction, the reducibility must be regarded as one of the most important properties of the material.

Jan 1, 1979

By Raffaella Granata, Wesley Schmutzler, Matteo Bertoni

"The Lower Wood River Levee system, at the confluence of the Wood River Creek and the Mississippi River, in East Alton, Illinois, has been plagued with underground seepage and, in 2010, remediation was deemed necessary by the Southwestern Illinois Flood Prevention District Council and the United States Army Corp of Engineers (USACE). The experts enlisted by the council produced a design that provided for constructing a cutoff wall approximately 2,000 feet long and up to 140 feet deep, through alluvial and outwash soils, and embedded in bedrock. This paper will describe the challenges faced by the Quality Control (QC) and Quality Assurance (QA) teams due to the complex nature of the project in conjunction with an extremely thorough QC/QA program.INTRODUCTIONThe “American Bottom” is an area of 453 km2 (175 square miles) in Southwestern Illinois, extending from Alton south to the Kaskaskia River, which is home to 156,000 people. In the 1940s and 1950s the U.S. Army Corp of Engineers (USACE) designed and built a 120 kilometer (74 mile) long levee system to protect the area from a 500-year flood event on the Mississippi River, which flows through it. The levee system has been plagued by under-seepage for several years. The phenomenon has worsened to varying degrees, depending on location, to the point that remediation was needed.The Southwestern Illinois Flood Prevention District Council (SIFPDC), to obtain Federal Emergency Management accreditation, in June 2010 commissioned a team lead by Amec Foster Wheeler for the design and management of the required levee improvements. The team presented in 2011 the project’s first set of drawings showing proposed design features throughout the levee system. The project was subdivided in four areas, based on the controlling levee districts, one of which, the Wood River Drainage and Levee District, was split into three subdivisions: Upper Wood River, East-West Forks of Wood River, and Lower Wood River.The project included the installation of a cutoff wall at the confluence of the Wood River and the Mississippi River in East Alton, IL (Fig. 1). The Engineer of Record (Amec Foster Wheeler) considered the cutoff wall as the only viable solution to stop the severe under-seepage that was undermining the integrity of the Lower Wood River Levee. The Lower Cutoff Wall (LCW) project is the subject of this paper."

Jan 1, 2017

By Heyer T, Wasmuth H-D

The concentrator plant of Fahrica Mine, that started production in 1977, was using nine Jones wet high intensity magnetic separators (WHIMS) of the standard type DP 317 with a 1.5 mm gap width for the production of pelletfeed concentrate. These WHIMS units were operating in parallel with a feed rate of 110 t per hour, with about 47 per cent Fe in the feed, and with a maximum of only 0.8 per cent magnetite. The field strength was about 1.2 Tesla. From 1986, the mine has adapted its production facilities to mine and concentrate larger amounts of lowgrade itabintes to maximise the use of the available iron ore reserves. An increase of up to three per cent magnetite in the magnetic separator feed, resulted in a reduction of capacity. This was due to partial clogging of the separation boxes at high field intensities, which were required for the recovery of the very fine hematite. Even by lowering the feed rate and the field intensity the problem could not be resolved. After extensive testwork in a pilot plant, with a Jones separator model DI' 90, the commercial WHIMS plant was modified into a two stage process using the existing nine Jones separators. The gap of the first stage with four machines was increased to a width of 3.5 mm, corresponding to a maximum field intensity of 0.7 Tesla. This first 'medium intensity scalping stage' is followed by a second 'real' high intensity WHIMS step with five machines operating at the original settings with 1.5 mm gap width and 1.0 Testa maximum field intensity. Feed rates of up to 320 tons per hour in the first and up to 240 tons per hour in the second stage could be achieved. The design concept of the concentrator at Fabrica mine is described using the old and new flowsheets. Details of the pilot plant testwork as well as actual performance data of the new plant section are presented.

Jan 1, 1993

Federal lands often contain extensive mineral resources and decisions affecting access to those lands are made with knowledge of the possible minerals-related consequences. Information is provided to the Bureau of Land Management (BLM) in this report for use in preparing environmental impact statements on the Western Mojave Management Area (WMMA) and the Desert Tortoise Priority Habitat (DTPH). To augment U.S. Bureau of Mines (USBM) efforts such as the Mineral Assessment of the Planned Foil Irwin Expansion, Modified Silurian Valley Alternative, San Bernardino County, California which is in progress, and the Economic Analysis of the Minerals Potential of the East Mojave National Scenic Area; California, the USBM studied mineral deposits and estimated the potential impacts of mining in a segment of the California desert; the 8.7-million-acre WMMA, an area which includes the 1.2-million-acre Desert Tortoise Priority Habitat (DTPH). In addition, this information is intended to assist administrators, legislators, and the concerned public in understanding the economic importance of mineral resources in the California desert, especially that portion designated as the WMMA. See figure 1.

Jan 1, 1993

By Len Blackman

The Absaroka-Beartooth Study Area is a tract of approximately 1.4 million acres of National forest land in southern Montana, part of the Greater Yellowstone Area. This study evaluated the mineral potential of four mineral terranes containing undiscovered resources in the area. The geological data is probabilistic, with estimates of the possible number: of deposits and their grades and tonnages. Possible future development scenarios range from no development to many mines, including some very large. As two thirds of the study area is within the Absaroka-Beartooth Wilderness, the future development scenarios reflect the area's mineral potential, not what we expect to see in the foreseeable future. Based on the analysis performed on these four terranes, the most likely future scenario for the study area would include the potential for two medium sized, (predominately) gold, mines, each employing a few hundred workers. There is a small chance, less than 5%, that a large Porphyry Copper or Superior Iron deposit would be discovered and be economically feasible to develop.

Jan 1, 1994

By Robert W. Hunt

The first pump of this character, made by H. R. Worthington, and, so far as the writer is informed, the first and only one of this kind ever constructed, is now in daily use in the above-named works. The water-pressure necessary for the working of the hydraulic machinery of this plant had been supplied, up to the time of the building of this pump, by two Worthington Duplex High Pressure Pumps, having steam-cylinders of 20 inches diameter and 12-inch stroke, with water-plungers of 71/2 inches diameter; eight inlet and eight outlet valves of 24 inches diameter, and pumping into a 6-inch pipe. These pumps required a large amount of steam, and, in consequence of the various additions to their duty, their capacity became far short of the work required. In preference to putting in another engine of the same class, it was decided to accept Mr. Worthington's proposition to build the compound one under description, he guaranteeing that it should be equal to the demands of the works, and at the same time cause a saving of from 5 to 6 tons of coal per day from the amount required to run the two old pumps. The new engine has been in operation about one month, and so far has exceeded the most sanguine expectations. It consists of two high-pressure cylinders of 21 inches and two low-pressure ones of 363/8 inches diameter, by 36-inch stroke, with water-plungers of 961/2 inches diameter. There are two air-pumps of 20 inches diameter by 18-inch stroke; the condenser being 24 inches diameter by 60 inches high. Both cylinders are jacketed with wood and felt, and the low-pressure cylinder also with live steam. The high and low pressure steamcylinders are in line and immediately adjoining each other, while the inconveniences attending an internal stuffing-box are avoided by having two piston-rods for each of the low-pressure cylinders, running through stuffing-boxes on the outside of the smaller high-pressure ones. The steam-valves are very ingeniously designed balanced

By A. Sampson-Forsythe, P. Morissette, A. R. Punkkinen, D. R. Chinnasane

"The performance of ground support systems under dynamic loading is typically assessed in a qualitative and subjective manner. As a result, it is difficult to develop an explicit knowledge on the mechanisms of action and interaction of support elements subjected to rockbursts. This paper examines rockbursts that have occurred at Creighton, Copper Cliff, and Coleman mines since 2000, 2004, and 2006, respectively. The mines are located in the Sudbury Basin, in Ontario, Canada. The majority of pertinent information was obtained through on-site field assessments, seismic system records, and numerical elastic stress modelling. Passive monitoring is used to link the evolution of the frequency and severity of rockbursts to the evolution of mining and support practice at the three mine sites. Based on the collected data, ground support elements that enhanced the capacity of support systems to withstand dynamic loads are identified. IntroductionThe selection of appropriate mining methods, extraction sequences, rock mass de-stressing techniques, and ground support systems is of great importance in mitigating the level of rockburst-related risk. In burst-prone conditions, the design of support systems should account for the anticipated dynamic load demand and the capacity of the available support options. Furthermore, an economical design should, implicitly or explicitly, take into consideration the consequences of a rockburst and its impact on worker safety and mine productivity. Stacey (2012) has argued that we have a limited understanding of the mechanisms of rock mass behaviour in seismic conditions. This is compounded by a ‘lack of understanding of the mechanisms of action and interaction of support elements under dynamic loads’ (Stacey, 2012). Consequently, the design of support systems required to manage dynamic loads is usually based on experience. The assessment of the dynamic performance of ground support systems is typically subjected to qualitative (and sometimes subjective) interpretations from ground control personnel."

Jan 1, 2017

The St George orebodies are situated within the tectonically disrupted eastern limb of the Boogardie Syncline.Highly disturbed rafts of banded chert formations occur within a sequence of felsic volcanic tuffs. The chert forms the hostrock for the gold mineralization.The gold distribution within the irregular and narrow banded chert formations is erratic and patchy. The average gold content of the two orebodies is between 3 - 4 g/t Au.Economic mining of these relative small, irregular and low grade St. George orebodies can be carried out by using a highly selective mining method.The highly selective mining method uses an excavator as the principle mining tool. Blasting, breaking and loading of the rocks is done in a different way than by using a front-end loader as with the conventional mining method. Simple, and therefore cheaper, blasting breaks the rocks and lifts them up without major displacements.

Jan 1, 1984

By Andrea Koschinsky, Luise Heinrich, Stefan Gößling-Reisemann

"Germany, like several other countries, has entered a contract with the International Seabed Authority (ISA) to explore the prospects of commercial manganese nodule mining in the Clarion-Clipperton Zone (CCZ). Ensuring a maximally sustainable deep-sea mining operation requires a thorough understanding of the environmental impacts associated with every step of the mining process from the extraction of the nodules at the seafloor to the refinery on land. Against this background, the project presented here applies a combination of scenario-building and life cycle assessment (LCA) to assess and evaluate the sustainability performance of the individual process steps as well as the entire mining operation.Life cycle assessment (LCA) is a comprehensive methodological framework that allows the identification and quantification of impacts occurring during a products life-cycle, as well as the analysis and evaluation of their contribution to pre-defined impact categories, such as climate change, acidification and toxicity (Rebitzer et al., 2004). Until now, LCAs with a focus on raw material extraction have almost exclusively been applied to terrestrial processes. Noteworthy exceptions are offshore drilling, offshore wind farms and ocean fishing. Hence, the first part of the project is to investigate in how far LCA can be applied to deep-sea settings and if and in what way it could be adapted to be used in a deep-sea mining context."

Jan 1, 2017

Frank Owen, El Perú Venezuela (communication to the Secretary): Mr. Cragoe's accurate description of the rich and extensive mines of the Frontino and Bolivia Co. is of much interest to those acquainted with Colombian mining. While the labor in that part of Colombia is, of course, admittedly far inferior to that of white miners, it is,. nevertheless, decidedly superior to that available in other parts of the republic, and in the northern mining regions of South America generally. The Autioquenos have been miners for several generations, and many of those employed at the Frontino Co.'s works have been brought up at the mines, which is a distinct advantage. The ground encountered in the surface-workings of that district being very treacherous, they are skillful timber-men, every miner being able to put in his own timber in tunnels, stopes, etc., so that, except for the main shafts, where sawn timber is used, special timber-men are not required. In the shallow workings it is the custom for a miner to come out of the mine into the thickly-wooded bush and select and cut the timber he requires, which he will then take into the mine and put in

Jan 1, 1899

By K. C. Corin, M. S. Manono, R. M. Manenzhe, J. G. Wiese

"Environmental concerns necessitate the recycling of process water within mining operations. Given that recycled water is chemically different from fresh water, and collectors are added such that they adsorb at the liquid-particle interface, changes in the aqueous phase are expected to affect collector adsorption. A Finnish nickel-copper ore was floated in synthetic plant waters of varying ionic strengths and plant waters obtained at Boliden Kevitsa Mine, with aerophine and sodium isopropyl xanthate as collectors. Of the tested waters, the copper thickener overflow was the least conducive to xanthate adsorption and valuable mineral recovery. The nickel thickener overflow, standard process water, and raw water were the most conducive to xanthate adsorption. For the raw water and nickel thickener overflow, increased adsorption correlated with increased valuable mineral recovery. Further, recycling xanthate retained in water affected the selectivity of the collector and hence the concentrate grades.INTRODUCTIONFlotation is a separation process that exploits the differences in the surface properties of the particles being separated. The efficiency of separation is dependent on the degree of hydrophobicity achieved by the particles meant to be floated, which are, in most cases, valuable minerals. The hydrophobicity is in turn dependent on the adsorption of the chosen collector onto the surfaces of the floated particles (Fuerstenau, 1984; Taggart and Hassialis, 1946). Empirical findings suggest that species dissolved in solution strongly influence collector adsorption and overall flotation response (Fuerstenau and Chander, 1986). Due to environmental concerns, it is becoming more pertinent for mining plants to recycle process water and hence limit the usage of potable water. There is an interest to ensure minimal discharge of plant water into the environment, as this water is typically polluted with process reagents that may render it toxic (Levay et al., 2001).Recycled water, however, has been shown to adversely affect flotation. Reagent efficiency can be reduced due to increased suspended solids. A loss of mineral recovery can occur due to competitive adsorption between reagents and other dissolved species, loss of reagents due to precipitation, and unwanted reactions. Further, a reduction in grade can occur due to non-selective coating of reagents on valuable and gangue minerals, and hydrophobic coating of microbiological material on gangue, causing unwanted flotation. Yet despite these drawbacks, water reuse has the advantages of minimal fresh water use and reduced reagent consumption by recovering the unconsumed reagents retained in wastewaters (Bruckard et al., 2011; Levay et al., 2001; Shengo et al., 2016; Slatter et al., 2009)."

Jan 1, 2018

By Roy E. Williams

1. The major sources of heavy metal ions in wastewaters of the Coeur d'Alene Mining District are effluents from metallurgical processing plants. Effluents from mine operations provide a secondary source for heavy metal ions. Based on data analyzed by the Federal Water Quality Administration, mercury and arsenic are escaping from some mill waste ponds, but they are in the suspended phase. 2. Metallurgical process effluents are combined with mine waste effluents in tailings ponds, consequently, the quality of the tailings pond decant water is highly degraded. The major effect of combining metallurgical process effluents with mill wastes is a drastic change of pH in the tailings pond. This chance may be an increase or a decrease depending on the metallurgical process. The effluent from an electrolytic antimony plant drastically increases the pH in the tailings pond permitting the removal in solution of antimony via the pond decant system. The addition of low pH effluents to the tailings ponds results in a net decrease in pH which makes lead, zinc, cadmium, and copper more soluble, thereby permitting their removal from the pond via the decant system.

Jan 1, 2011

By W. Roggenthen, Z. J. Hladysz, G. D. Callahan, W. G. Pariseau, W. Weinig, C. Randolph-Loar, R. Popielak

A Deep Underground Science and Engineering Laboratory (DUSEL) is being planned at the site of the former Homestake Gold Mine in Lead, SD, under the sponsorship of the U.S. National Science Foundation (NSF) in cooperation with the Department of Energy (DOE). This national facility will host a variety of multidisciplinary science and engineering experiments, including physics experiments that require shielding from cosmogenic radiation. Current plans include construction of large rooms (up to 55 m in width) at depths of 1.48 km (4,850 ft) and 2.25 km (7,400 ft) below the surface. Preparation of the preliminary design required the development of a geotechnical characterization program, including preliminary drilling and coring, core logging, drill hole mapping with a televiewer, drift mapping of the geology and rock structure, in situ stress measurements, and laboratory testing of the mechanical properties of the rocks and discontinuities. Overall rock quality is very good to excellent. Site investigations included geotechnical assessments for the construction of caverns and laboratory modules. The results are favorable and reaffirm selection of the Homestake site for establishment of a Deep Underground Engineering and Science Laboratory.

Jan 1, 2011

By R. S. Dean

A large metallurgical experiment station at Salt Lake City to house the works of the Bureau of Mines in the intermountain area properly has long been projected. It finally became possible when a Public Works Allotment of $300,000 was set aside for building and equipment. With the new building assured, the Bureau of Mines decided to move the headquarters of its Metallurgical Division from Washington, D. C., to Salt Lake City, Utah. It was felt that this move would simplify they administrative work of the chief engineer of the division, as all stations devoted primarily to metallurgical work are west of the Mississippi. These include Rolla, Mo.; Minneapolis, Minn.; Pullman, Wash.; Reno, Nev.; Berkeley, Calif.; Boulder City, Nev.; and Tucson, Ariz. In addition to these stations will groups, of investigators working on metallurgical problem, are maintained at Pittsburgh, Pa., and College Park, Md. Salt Like City was clearly a more central point for the direction of this scattered work than Washington, D. C. The building (fig. 1, A and B) was designed from general plans worked out by the authors of this paper. Contraction was begun in March of 1939, and by the end of the year the Metallurgical Division had moved, into its now quarters.

Jan 1, 1940

By Ana E. Bohé, Fabiola J. Alvarez

"The separation of nickel from the aluminum present in spent catalysts and different metallic industrial residues, is proposed in the following systems: alloy Al2Ni and the mixtures 50 wt% Ni + 50 wt% Al, 10 wt% Ni + 90 wt% Al2O3 and 12 wt% NiO + 88 wt% Al2O3. The experiments were carried out in a tubular reactor with a flow of 2 l/h of gaseous chlorine and from 200 ° to 800 °C. The final products of the reaction, extracted from the hottest zones of the reactor where characterized by XRD, SEM, EDS, AA and XRF, as NiCl2 y NiCl2.6H2O while in the coldest regions AlCl3 was deposited in the first two cases and in the other there was a residue of ?, a- Al2O3, sometimes mixed with some remainder of Ni and NiO. The procedure attained different separation factors which showed the optimun conditions for the recovery of both metals. Introduction Some studies of nickel corrosion were carried out in chlorine gas at temperatures above 950ºC, and suggested that nickel is not corroded below 538ºC. [1] However, in a previous work it was shown that the chlorination allows the separation of nickel from aluminum and the formation of NiCl2 was detected from 200ºC in binary mixtures Ni-Al 50 wt%, for isothermal conditions in chlorine flux. [2] Other researchers obtained selective chlorination above 650ºC of a fly ash containing 1.4 wt% of Ni and other metals (V, Mg, Al and Fe). The Ni was separated from the Mg and NiCl2 started to vaporize at 550ºC and was after condensed in a zone of the reactor above 380ºC with 90% of purity. [3]"

Jan 1, 2008

By William Metcalf

It is the object of this paper to oppose unnecessary changes, and the introduction of new and confusing terms. From the earliest times of which we have ally record on the subject, iron has been divided into general classes. Whether iron was first known in the form of wrought iron or of steel, is a matter of no importance; but at the time when cast iron first became a prominent article of commerce, wrought iron and steel were old products— steel, at that time, being generally made from wrought iron by the process of cementation. As steel was then properly defined as iron containing more carbon than wrought iron, so cast iron was appropriately defined as iron containing more carbon than steel. Until the year 1776, when Huntsman first began the manufacture of a new kind of iron by melting wrought iron and steel in crucibles, the above definitions were all that could be desired. At first, probably, owing to imperfect appliances, only a highly carburized iron was melted in crucibles, and this led to its being called cast steel. If our ancestors had found a name for this material not involving the use of the word steel, we would have been saved the trouble of the present discussion. As the arts developed, new uses were found for steel, and the products of the crucible were varied, until at the present day it is quite common to find steel containing no more carbon than average wrought iron, and other steel containing nearly or quite as much carbon as some cast iron. All of these various products of the crucible have retained, or received, the name cast steel, usually abbreviated to the simple word steel, without caus-ing any confusion among producers or consumers in regard to terms or their meaning. In 1865, twenty-one years ago, the Bessemer process was introduced ; this was followed in a few years by the Siemens-Martin process, and the products of both were at once, and have ever since been, called steel, from the fact that they were identical in chemical and physical properties with crucible cast steel. At the present time, then, we have three subdivisions of cast steel, viz.: Crucible cast steel, Bessemer cast steel, and Siemens-Martin,