Search Documents

By O A. Aladejebi, S Mitra, T Singh, D O’Dea, S, T Honey

Granulation of the iron ore blend and the additives is the foremost step in the agglomeration of iron ore fines to achieve a permeable bed during sintering, which is crucial for sinter productivity. This study investigated the granulation of four types of blends to determine the impact of granulation on bed permeability. The blends were granulated in a rotating drum at various moisture contents and their JPU permeability was measured at each moisture content in a permeability pot (diameter 95 mm and height 500 mm) at various flow rates. Several independent experiments were carried out to investigate the changes in permeability when mixtures of different particle size range (-1 mm and +1 mm) were introduced into a packed bed with a larger particle size range (-6.3 mm to +4.0 mm). The results revealed that the addition of particles in the -1 mm size range had a more pronounced negative impact on permeability compared to particles in the +1 mm size range. This can be attributed to the relatively higher energy losses (mainly inertial) associated with the presence of -1 mm particles in the mixture. The findings were used to quantify the granulation process based on the -1 mm particle size fraction in the granulated mix and their utilisation (denoted by UI-1 mm). For achieving optimal permeability in a specific blend, it was found that a UI-1 mm (utility index of -1 mm particle size) ranging from 0.82 to 0.92 was required. However, exceeding a UI-1 mm value of 0.95 resulted in weaker granules prone to deformation and led to decreased bed permeability. The study also showed that the UI-1 mm was highly dependent on the water addition per kg of -1 mm in dry feed and suggested adding ~80 to 110 mL of water per kg of -1 mm in dry feed to attain the best possible permeability. Additionally, the research proposed a mechanism involving the melting of granules at high temperatures and highlighted the influence of -1 mm particles on bed permeability during the sintering process.

Sep 18, 2023

By J. L. Thompson

Lime made in a coal-fired, rotary kiln has two distinct parts: the interior of the pebble which constitutes about 90% to 95% of the mass, and the surface dust layer which is the remaining 5% to 10%. Uncalcined carbonate and impurities in the product may be present and will not contribute to the hydration reaction. Sulfur, in the form of calcium sulfate, inhibits the hydration reaction out of all proportion to its actual weigh-percent concentration (perhaps more than 100 times). If the stone contains dolomite, this will also inhibit the reaction as its rate of hydration may be nearly 3 orders of magnitude slower than that of calcium oxide. Early in the hydration reaction dolomite appears practically inert, but given sufficient time, it will hydrate. The heat of reaction is nearly the same as for calcium oxide, but the time necessary for complete hydration may be hours; whereas for calcium oxide it is only fractions of a second. The dust layer on the surface also inhibits hydration as it contains a collection of compounds which have low heats of hydration. This layer can tie up additional calcium and delay or prevent its reaction. In addition to these chemical processes, an important physical characteristic of the lime is its specific surface area. This is effected by the thermodynamics of calcination and the original stone grain chemistry. All of these factors are agglomerated in the gross slaking rate of lime. The total hydration of the chemical complex that is called commercial lime can be more easily understood by considering the individual reactions and combining them to form a more comprehensive picture of the situation. Calcium oxide and magnesium oxide hydrate similarly, differing only in their reaction kinetics. Dolomite, however, reacts differently than a simple mixture of calcium oxide and magnesium oxide as its hydration is strongly influenced by calcination thermo-dynamics and stone grain structure. Finally, the dust hydration and composition should be examined Understanding these reactions enables one to examine hydration reaction graphs with more insight into the factors which determine their shape.

Jan 1, 1978

By B Small

CSA Mine, named after the nationalities of the mines first owners being Cornish, Scottish, Australian, is one of Australia’s deepest and highest-grade copper mines. A combination of the modified Avoca method and shrinking was a standard practice where production rings were fired against and bogged to waste fill. This method resulted in dilution and involved rehandling of waste material to refill the bogged stopes in the Western region and the QTS Central. The introduction of pre-charging blastholes using a wireless initiating system (WebGen™) has enabled CSA to design and fire stopes in reverse. This involves the use of a pre-charged Temporary Rib Pillar (TRP) against the waste fill material in a previously mined stope. The temporary pillar reduces dilution and improves conventional bogging as material is blasted towards the drawpoint rather than towards the waste fill material. Additional drill, prep and blast re-work is reduced or completely removed as rings can be charged prior to, in conjunction with, or after, charging of the slot. This is a safer practice as the charge crew spend no time working adjacent to a brow or open void. A TRP trial was conducted in the western orebody at CSA. The risk of exposure to a brow or open void while charging underground, and the bogger rehandling of waste material was successfully eliminated. Once reverse stoping was established in modified avoca stopes at CSA, two TRPs were implemented in challenging ground conditions in the QTS Central region. The TRPs were utilised in a retreating four-way intersection to extract a central diminishing pillar to close the level out. The ore recovered in this stope provided 5 per cent of CSA’s copper for the year. Without pre-charging with a wireless initiating system, two 5 m pillars totalling 6936 t of ore at 7 per cent either side of the stope would not have been recovered. CSA has implemented the practice of reverse stoping in modified avoca stopes using TRP for ten stopes since the successful trial. The development of additional blasting techniques enabled by precharging with wireless initiating systems is currently underway in the QTS North orebody at CSA Mine.

Mar 29, 2023

By J Sargeant, T Levi, J Theiler, B Beamish

Two coal samples (810 Panel and Area 900) collected from Clarence Colliery have been tested under a controlled heating procedure to evaluate the gas evolution trends corresponding to increasing temperature. Gas evolution data are normally used to identify key gas indicators and validate the trigger action response plan settings for the mine as part of the Principal Hazard Management Plan for Spontaneous Combustion. The samples were located some 6 km apart and there is a significant coal-type difference between them. At low temperatures (<100°C), the Graham’s ratio (GR) values for the two samples are almost identical. However, at elevated temperatures, there is a significant difference, with the 810 Panel coal having higher GR values than the Area 900 coal. This is most likely due to a difference in the coal reactivity. The 810 Panel coal does not evolve ethylene until temperatures in excess of 140°C are reached, whereas Area 900 coal evolves ethylene once temperatures in excess of 120°C are reached. The 810 Panel coal also produces significant ethane evolution (200 ppm) at low temperatures (50°C) due to the presence of retained ethane seam gas, which decreases as the temperature increases due to desorption from the coal. Once the coal temperature exceeds 130°C, the ethane evolution increases again due to coal oxidation reactions, reaching levels of 50 ppm. In contrast, the Area 900 coal has no significant low-temperature ethane evolution, and ethane evolution only increases once the coal temperature exceeds 120°C. There are also noticeable differences in the trends of other gases evolved from the coal. These findings have implications for the interpretation of gas monitoring results from the two different areas of the mine. They also illustrate the need for obtaining results from each new area of a mine as it develops so that changing gas evolution trends can be identified in advance of mining.CITATION:Beamish, B, Sargeant, J, Levi, T and Theiler, J, 2015. Gas evolution trends for coal from two different areas at Clarence Colliery, in Proceedings The Australian Mine Ventilation Conference, pp 273–278 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

"On-site research and development as well as in-situ testing are key factors to the successful implementation of new mining equipment and technology. Unfortunately the demands and necessities of research and development often conflict with the reality of mine production in operational mines, especially during early stages of research and development and the initial testing of new equipment. Several experimental mines under university supervision attend to this problem and provide a close-to- reality testing environment for the mining industry and mining equipment manufacturers. This paper gives an overview of the design and organization of such an underground testing area as well as of the wide range of possible operations it can facilitate at the example of the FLB Experimental and Teaching Mine (Forschungs- und Lehrbergwerk) at Technische Universität Bergakademie Freiberg, the central European underground research mine. INTRODUCTION As well as the Mining Engineering education follows the same pattern worldwide, the tasks and duties to be fulfilled by engineers in the productive mines are comparable around the globe. This also holds true for the technologies and equipment needed, both in surface and underground mines. Almost all mining equipment brands are being distributed worldwide. The tasks and challenges of guaranteeing an ever- increasing productivity at the mines, while simultaneously maintaining, respectively improving, safety standards, also in the developing countries and emerging economies, requests a constant development, improvement and adaption both of the engineering education and of R&D in technology and equipment. The increasing safety requirements at the mines, in combination with also increasing safety and liability policies, do often not allow a proper practical education of mining engineering students. At the same time, new technologies and equipment to be deployed / brought to the mines have to be fully functional in a production operation from the very first moment. Time losses like break-down time or even repair and maintenance breaks are often costly and, even when expected up to a certain degree with newly developed machines, have a wider negative impact on the neighboring operations and operations within that mine, thus often being unacceptable within the ongoing production process and extremely costly."

Jan 1, 2015

By V. V. Lvov, L. S. Chitalov

"The purpose of the research is intensification of physico-mechanical ore properties determination for ball grinding processes in comminution circuits. The research presents comparative studies aimed at intensification of Bond Ball Mill Work Index (BWi) determination, such as testing technique of Ahmadi and Shahsavari, Berry and Bruse, Gharehgheshlagh, Horst and Bassarear, Kapur, Magdalinovich. The subject of the research is a test procedure of apatite-nepheline, copper-nickel, gold-sulfide and iron ores for the Bond ball mill index. The Bond Ball Mill Work Index for the material firstly was determined by standard Bond test methodology. Two the most promising testing techniques - Ahmadi and Kapur testing techniques - were modified. For the Ahmadi technique it was proposed to pay attention to the circulating load, which should be stabilized on the value of 250% as fast as possible. Two methods were put forward to quicker stabilize the circulating load. For the Kapur technique it was proposed to use empirical coefficients, which is determined especially for the apatite-nepheline, copper-nickel, gold-sulfide and ores. The modified Ahmadi and Kapur techniques require no more than two cycles of ball grinding to determine BWi (while normally 6-8 cycles are required) and less than 5 kg of initial feed. The suggested modified Ahmadi and Kapur techniques allow to intensify the physico-mechanical ore properties determination for ball grinding processes and BWi test costs considerably, which makes them useful for mass sampling and monitoring strength properties of ores entering a concentrating mill. INTRODUCTION When designing concentrating mills, the choice of the technological scheme for ore pretreatment, particularly the type, quantity and size of the main process environment, the determination of optimal grinding conditions and the calculation of equipment load are carried out by preliminary studies of grinding in semi-industrial or laboratory-scale plants. Semi-industrial tests on full-scale plants provide the most reliable information for calculating specific loads for equipment. However, this requires a significant amount of ore samples, a high labor costs and the pilot plants. Thence the most researchers performed grinding tests with small laboratory equipment using small ore samples."

Jan 1, 2018

By Zhang Chuanfu, Tan Pengfu

"A thermodynamic model is developed to simulate nickel flash smelting process. In the nickel flash furnace, oxidation of concentrate occurs at one end, and reduction of slag occurs at the other. The model makes use two zones, namely the reaction shaft/settler zone and the appendage zone and accounts for 6 phases (matte, slag, silica, magnetite, Cu-Ni alloy and gaseous phase), 13 elements (Ni, Co, Cu, Fe, S, 0, N, C, H, Si, Al, Mg and Ca) and 33 chemical components in nickel flash smelting system. The compositions of matte, slag and gaseous phases in equilibrium are calculated by using the data of free energies of formation and activity coefficients of components. Two nickel sulfide species are used to allow for the modeling of sulfur-deficient mattes. The model predictions are compared with the known industrail data from Kalgoorlie Nickel Smelter, and excellent agreement is obtained. The model can be a very useful tool for monitoring and optimizing the actual industrial operations of nickel smelting process. The distribution behaviors of Ni, Co, Cu, Fe, S and 0 in the nickel smelting furnace depend on the process parameters such as smelting temperature, volumes of air, the content of the elements~ charge and oil.1. IntroductionThe nickel flash smelting furnace essentially consists of a reaction shaft where nickel sulfide concentrate is partially oxidized with air, a settle zone where matte and slag are allowed to separate, and a slag cleaning end where coke is added to provide for the reduction of the oxidized nickel from slag, and electrodes are used to provide heat.The theoretical model to consider a mass balance for copper flash furnace is developed by S. Goto and R. Shimpo[1][2J. However, this can not be true for nickel flash furnace as a whole since oxidation of concentrate occurs at one end (in the reaction shaft/settler), and reduction of slag occurs at the other (in the appendage). Despite these limitations, an acceptable pseudo-thermodynamic description of the furnace can be achieved using essentially two zones, namely the reaction shaft/settler zone and the appendage zone. Compositions of gas, slag and matte in two zones are calculated."

Jan 1, 1998

By Kimiaki Utsunomiya, Yasumasa Hattori, Yoshiaki Mori, Toyokazu Okubo

"The effect of various operating conditions on splashing behavior in a Peirce-Smith converter has been investigated with a 1/5.7 scale cold model. Dynamic similarity between the model and a commercial converter was attained by setting the modified Froude number in the model experiments in· the range for normal converter operation. It is known that for a given modified Froude number the dimensionless penetration length of gas into the liquid phase increases as the liquid density decreases. Moreover, penetration· length has a large effect on splashing behavior. Therefore, a heavy liquid, a mixture of water and lead concentrate was used as the liquid phase. It was concluded that the amount of splash dramatically decreases with a reduction in the buoyancy energy per, unit liquid mass and an increase in the horizontal distance between the tuyere tip and the edge of the mouth.IntroductionSubmerged gas injection is widely used in practice in ferrous and nonferrous pyrometallurgical operations to achieve large gas-liquid contact areas and good agitation of liquid for rapid chemical reaction. The common application in ·nonferrous industry is the Peirce-Smith converter with multi-tuyere for copper and nickel matte converting. This process has been used for over 100 years because of its effectiveness in mixing of the molten bath, as well as its merits of the engineering simplicity. However, the mechanisms which · determine the blowing performance is poorly understood, and the design and operating conditions of the Peirce-Smith converter varies widely from plant to plant, such as by diameter, length, mouth angle, tuyere position and level of molten matte. Smelters have continuously made an effort to increase converter productivity, implying maximum tuyere blowing rate. Above a certain critical blowing rate, splash of molten matte from the converter mouth becomes unacceptable because of dangerous ejection and accretion buildup around the converter mouth, which results in interference with effective hood sealing. In fact, a 1993 converter survey[!] reported that splash was a major limiting factor for blowing rate and 54% of responding plants from around the world regard it as a limiting condition[2]. In order to increase tuyere blowing rate a study of the effect of various operating conditions on splashing behavior is expected."

Jan 1, 2000

By Alex Luyima, Jaan Kers, Lifeng Zhang

"The pyrolysis of PWBs was investigated by a TG-DTA-MS furnace at 300–1173 K. The kinetics and the control of emitted gas during the pyrolysis of PWBs with and without chemical additives were studied. Moreover, the possibility of controlling the amount of toxic exhaust gases like HBr, C6H6, Br2, Cl2, HCl gas and recovering beneficial gaseous fuels like CH4 and H2 from pyrolysis process is discussed. The MS data for each PWB sample were examined as a function of temperature and particular m/z values could be associated with the mass loss steps in the TG data. The degradation of the organic material was characterized by m/z = 2, 16, 18, 28, 36, 44, 71, 78, 81, and 160. Fe2O3 was the best inhibitor of toxic HBr and C6H6 when compared to Al2O3, CaO Y-zeolite and ZSM-5. Moreover, it had no significant effect on the valuable H2 and CH4 gas evolution. This selective inhibition of toxic gases while maintaining the valuable ones make Fe2O3 the best candidate among the investigated additives in controlling gas emissions from PWB pyrolysis process.IntroductionThe electronic and electric industry is one of the world’s largest and fastest growing manufacturing sectors. As a consequence of this growth, electrical and electronic waste (e-waste), such as computers, washing machines, printers, mobile phones, television sets, stereos, radios, etc., is generated in large quantities around the world. Printed wiring boards (PWBs) are a common component of many electronic and electric systems.[1]. The rapid development and expansion of the electronics industry over the past several decades have led to a dramatic increase in the production of PWBs and a corresponding increase in the amount of waste generated from both production and disposal. The environmental impacts of the treatment and recycling of PWBs waste have become a major concern [1-2]. PWBs are particularly problematic to recycle because of the heterogeneous mix of organic material, metals, and glass fiber [1]."

Jan 1, 2012

By Joe D. Mitzel

The Indian Head fine has been in existence since 1922. For over 56 years there have been North Dakota people mining coal at this same location. The area affected will fit inside a circle 5 km in diameter, and the coal is lignite. The seam thickness has varied from 2.4 m to 3.65m, and the overburden from 6 m to 30 m in depth. me Lignite coal which is being mined at the Indian Head Mine is from 15.8 x l0 6 to 16.7 x 10 6 J per kg; it has a moisture content of 33 to 38%; an ash content of 5 to 10%; and a sulfur content of from 0.5 to 0.7%. The moisture content and the fact that we crush the coal co a top size of 14 cm x 0, are two of the characteristics or the product which cause it to freeze and remain inside of the railroad cars on the slope sheets. The market for the coal initially was almost entirely local coal sales. That is, coal was sold to people in the area who used the lignite to heat their homes, stores, offices, schools, and churches. Back in the early 1920's, there were no stoker-fed boilers, or pulverized fuel boilers, as we have in today?s marketplace. Basically, all of the coal was sold as lump coal, pieces about 30 to 35 cm square, to be used in furnaces: and nut coal with a top size of about 7.5 cm to 10 cm to be used in the old kitchen cookstove. All of the coal fines, less than 5 cm, were screened out and layed onto a pile. There was no market for the smaller sizes of the lignite coal. It has been our experience that when the coal is in lumps or chunks larger than 7.5 cm to 10 cm, there is a very slight possibility of freezing. That is the chunks themselves freeze, but by their nature, they do not cling to one another or form large masses of frozen material which are difficult to remove from the slope sheers of the railroad cars.

Jan 1, 1980

By Mario H. Castro-Cedeno

"A design for a handheld MEMS chemical detector is proposed. The detector will be used to detect trace amounts of chemicals in air. It can detect drugs, toxic chemicals and/or explosives. The proposed detector will use ion mobility spectrometry (IMS), a technique that is well known for accuracy and has been used in the past in suitcase sized chemical detectors. The separation and detection of the chemicals occurs in the drift channel and the process was modeled using the finite element method and CoventorWare modeling software. A manufacturing process sequence for the drift channel is proposed and was demonstrated.IntroductionThe goal of this effort is to design, mode~ and prototype a MEMS chip that will be the key component in an ion mobility spectrometer (IMS). This technique uses and asymmetric potential to separate the various ion species in a stream of incoming air [1-4]. One advantage of IMS is its ability to separate chemical species from air at atmospheric pressure and temperature. This is a requirement for a simple to use handheld drug or chemical detector. IMS can be used to detect drugs, toxic chemicals and explosives and it is well known for accuracy in detecting very small amounts of chemicals. This chemical detection technique has been used in the past, but not in handheld detectors.One variant of IMS is the high-field asymmetric waveform ion mobility spectrometry or FAIMS [3]. The FAIMS process, shown in Figure l, works as follows: a gas sample is admitted into the instrument where gas molecules are ionized, typically by a weak radioactive isotope source, ultraviolet light source; and more recently through field emission. The ions move along the length of a channel while they are separated in the transverse direction by an asymmetric electrical potential. The potential, in the form of an asymmetric waveform, causes relative motion between the various chemical species. The species that hit the charged top and bottom plates are neutralized and only those ions that move along the center are detectable as charged chemical ions at the end of the channel."

Jan 1, 2004

By J. E. Conley

Available statistics show that the demands of the American chemical industry for sodium sulphate have been increasing slightly in recent years. The supply from domestic sources, particularly In the form of byproduct salt cake from the acid manufacturers, has been tending to decrease due to the growing manufacture of synthetic acid. Both hydrochloric and nitric acids are being synthesized from their elements. The natural result has been that a smaller amount of salt cake is available. Simultaneously, the expansion of the Kraft paper industry, especially in the South, has brought about greater demand for sodium sulphate in that section. This dean is being met by domestic byproduct salt cake, by imported German sodium sulphate made from potash waste liquors, and by favorable situated domestic deposits of Glauber salts and tile anhydrous salt, thenardite. No shortage of natural sodium sulphate exists in the United States, but usually such deposits occur in semiarid regions far removed from transportation facilities and from markets. Moreover, the major portion of the natural deposits is Glauber salt or mirabilite (Na2SO4 ? 10H20), which must be dried or dehydrated in order to meet consumer requirements. The water of hydration represents, roughly, 55 percent of tae total weight of the crude salts and therefore has a very important influence on transportation costs. In marry instances the cost of getting, even the dehydrated product to market is the deciding economic factor. Therefore, the recovery oil production of anhydrous sodium sulphate from plant-.waste liquors or from natural brines of suitable composition might be economically feasible. The U.S. Bureau of Mines, at its nonmetallic Minerals Experiment Station, New Brunswick, N. J., has, for a number of rears, been investigating the commercial possibilities of treating the complex saline mineral polyhalite (K2SO4?NgSO4?2CaSO4?2H20) for the recovery of potash and magnesia. Certain proposed processes (1, 2, 3, 4)4/ yield waste liquors that contain the bulk of the magnesium and sulphate originally combined as magnesium sulphate in the polyhalite molecule. Sodium chloride In limited concentrations is also present, as extensive beds of salt occur in strata overlying the polyhalite deposits. A typical waste liquor would contain:

Jan 1, 1936

By L. Andrews

Nickel is recovered as a by-product of the platinum-producing process operated by Anglo Platinum. The metal is mined mainly as sulphide minerals contained in platinum ores. These pass through the concentrating, smelting and converting process route and nickel is finally recovered by electrowinning. Smelting of the concentrated ore in the electric furnace produces a melt with a high slag to matte ratio. The resulting furnace slag is granulated and later milled and floated to recover matte. A project was initiated to investigate the distribution of nickel in the slag in order to improve recovery. Slag samples were examined using a combination of chemical and mineralogical techniques. The granulated slag was found to consist mainly of a silicate glass phase, which reflects the composition of the molten slag in the furnace. Nickel occurs as free matte granules, as matte phases locked inside the glass, and in the glass phase itself. Whereas nickel in the matte is as sulphide, most of the nickel in the glass phase appears to be oxide- bound(i.e. in solid solution). Milled slag as flotation feed showed recovery-limiting features such as free matte with oxidized surfaces and unliberated matte inclusions in the slag. The biggest nickel losses, assuming no tapping problems, are in the glass phase solid solution. Only around 40% of nickel would be recovered from the slag, even under ideal conditions. Spoon and pot slag samples were also examined to see if casting and crushing would improve recovery. Although larger and therefore more easily recovered matte phases formed, nickel partitioned into crystalline silicate phases, limiting the maximum theoretical nickel recovery to 70%.

Jan 1, 2004

By R. E. Vivas, J. Garcia

"INTRODUCTION Freeport-McMoRan is a leading international natural resources company that operates large, long-lived, geographically diverse assets with significant proven and probable reserves of copper, gold, molybdenum, cobalt, oil and natural gas. Freeport-McMoRan is the world’s largest publicly traded copper producer and largest producer of molybdenum. The Sierrita mine is an open pit truck and shovel operation from which copper and molybdenum are produced. An important key to Sierrita’s success lies in their ability to realize their plans in the field. In certain circumstances, the mine plans are not achieved, and the operation fails to meet its targets which is an issue revealed in reconciliation reports. This technical session discusses the methodologies and procedures used at Sierrita to monitor the implementation of the mine plans, measure the performance of the operation and reduce the variance between plan and actual. Ensuring the operation stays on target is vital so mine productivity and profitability can attain its maximum potential. PROJECT OVERVIEW The Sierrita mining complex is located in Pima County, approximately 20 miles southwest of Tucson, Arizona as shown in Figure 1. The first mining claims at Sierrita date back to the late 1800s while underground mining activities started in the early 1900s. However, open pit development of Sierrita began more than 50 years ago to become the modern mining complex it is today. In 2009, Freeport-McMoRan purchased the adjacent Twin Buttes copper mine, providing significant synergies in the Sierrita minerals district. This venture included the potential for expanded mining activities, operations growth for mining copper and molybdenum, and reclamation activity. It should be noted that in addition to copper and molybdenum, the Sierrita mine produces rhenium which is a rare and highly value metal. The ore deposit contains oxide and sulfide mineralization. The oxide ore is delivered to the leach process while the sulfide ore is routed to the crusher and mill circuit 4,700 jobs on Arizona’s economy Freeport-McMoRan partners with the communities near Sierrita to provide programs that contribute to their sustainability"

Jan 1, 2015

By Qingchun Yu, Baoqiang Xu, Yongnian Dai, Bin Yang, Fulong Zhu

"In this paper, the mechanism of the carbothermic reduction-chlorination process to extract aluminum from alumina in vacuum was investigated. The carbon monoxide (CO) content of the gas, phases of the reduction slag, surface morphology of the reduction slag and the product aluminum were measured by means of gas chromatography (GC), XRD, and SEM. The experimental results indicated that the content of CO in the gas decreased, but Al4C3 increased with time at 1773K during the carbothermic reduction process of alumina. AlCl(g) and graphite (C) were produced by the reaction between Al4C3 and AlCh(g) at 1773K, and then aluminum beads generated after the decomposition of AlCl(g). It implied the mechanism of alumina carbothermic reduction-chlorination process in vacuum involves three steps as follows: the carbothermic reduction of A}z03 to produce Al4C3, the chlorination of Al4C3 by AlCh(g) to produce AlCl(g), and the decomposition of AlCl(g) to produce Al(l).IntroductionAluminum is the basic raw material for many industries [1], and it is used extensively because of various excellent properties such as light weight, good malleability, high strength, excellent thermal conduction, high corrosion resistance and so on [2]. Industrial production of aluminum currently includes refining alumina and electrolytic aluminum processes. However, its development has been effected by some factors such as high energy consumption and heavy environmental burdens [3]. In the past several decades, there had been numerous attempts to produce aluminum by new methods. Extracting aluminum from alumina or bauxite directly by carbothermic reduction-chlorination process had been studied [ 4-6]. Although the alumina carbothermic reduction process [7~9] had been studied, the mechanism of the carbothermic reduction-chlorination process had not been systematically elucidated.In order to investigate the mechanism of the carbothermic reduction-chlorination process in vacuum, GC, XRD and SEM techniques will be used to determine the CO content and to characterize the surface morphology and composition of the slags at various temperatures."

Jan 1, 2011

By C. Salcedo, J. Vallance, J. Sáez, M. Robles, J. Spangenberg, S. Rosas, L. Fontboté

The Tambomachay ore deposit (13°28'36.78"S, 71°57'35.98"W, about 6 km north of the town of Cuzco, Peru) consists of Cu hosted in arkosic red beds of the Kayra Formation (Lower Eocene). Bornite, chalcopyrite, chalcocite, covelite, digenite, malachite, and chrysocolla occur disseminated in thin layers and in veinlets. The occurrence of the copper ores in a part of the red bed sequence containing green reducing layers, the presence of organic matter in interstices between the hypogene sulfides, and the sulfur composition of the copper sulfides (δ34S values between -16.9 and -12.4‰ vs VCDT) pointing to bacterial sulfate reduction, are strong arguments to propose that mineralization was caused by copper-bearing oxidizing saline basinal fluids that precipitate copper sulfides when they meet reduced sulfur in an organic matter-rich horizon. Faults parallel to the regional Tambomachay Fault could have acted as feeders for oxidizing basinal copper-bearing fluids. Fluid migration was probably driven by tectonically-induced topography gradient. INTRODUCTION A number of red bed Cu occurrences are known in the Cuzco region in the early Eocene – early Oligocene San Jerónimo Group (Gregory, 1916; Carlotto et al., 1996, 2011; Loza et al., 2004). In the past, copper ores were extracted in several small-scale mines in the surroundings of Cuzco, including Tambomachay, Tipón, and Zurite in the Cusco province and Ushpa, Guilda, Giovanna, and Langui in the Sicuani Province. The abandoned Tambomachay Mine (13°28'36.78"S, 71°57'35.98"W), about 6 km to the north of the town of Cuzco (Romero et al., 2015; Salcedo et al., 2017, Fig. 1) was chosen as the main site for the present research aimed to better study the genesis of these copper occurrences. Results deriving from fieldwork, microscopic characterization of ore and host rock, and sulfur isotope determination suggest that the key factor for the genesis of the copper ores is that copper transported by oxidizing basinal fluids is trapped by reduced sulfur of bacteriogenic origin located in a part of the red bed sequence that shows intercalatins of green reduced horizons.

Jan 1, 2019

By John E. Udd

"For decades, writers have expressed concern about impending shortages of professionals for Canada's minerals industry. Even under the present difficult economic circumstances, it is anticipated that the supply which will be available will not be adequate to meet the requirements in certain key areas including mining and petroleum engineering. It is evident that, unless further initiatives are taken, shortages will exist for some time.In this paper, the writer reviews information which relates to both the demand for, and the supply of, persons with advanced-level education in minerals-related disciplines. In particular, a summary is made of the information regarding supply which has been collected by the CIM General Committee on Education for many years.In concluding, the writer expresses some personal opinions regarding imbalances between demand and supply and offers some recommendations for future actions.IntroductionLast year, in a paper which was presented at the Annual General Meeting of the CIM in Calgary, the writer presented a review of the situation regarding professionally educated manpower for the minerals industry, and concluded that indications were that the gap between demand and supply was widening and that the situation could be expected to continue. Since that time, the deterioration of the nation's economy has caused an appreciable reduction in demand. Simultaneously, a further annual survey by the CIM has shown that the numbers graduating in certain specializations, notably geology and some of the technologies, are rising very rapidly. One of the great concerns of educators at present is that adequate opportunities may not exist for all of those who are now graduating.The danger of the present situation, then, is that a momentary lack of opportunities may cause potential students to choose alternative careers . Because of the lead-time which is involved, it is very possible that this could result in greater shortages during a period of economic recovery or expansion. Action must be taken to ensure that adequate numbers will be attracted to the industry, and this applies particularly to those who have already made the career decision and who are enrolled in minerals-related programs."

Jan 1, 1982

By Wayne Bell, Xiaodi Huang, Matthew Andriese, Jiann-Yang Hwang, Zhiwei Peng

"The equations for determining microwave field attenuation length and half-power depth in magnetic materials were derived from Maxwell’s equations. The microwave field attenuation length and the half-power depth for a magnetite concentrate were calculated and the temperature dependence of them was determined. It is demonstrated the microwave field attenuation length and the half-power depth highly depend on temperature and decrease with increasing temperature up to 900 °C. The variations of field attenuation length and the half-power depth with temperature indicate the microwave power attenuates much faster than the field strength in materials. The evaluations of field attenuation length and microwave half-power depth can be used to characterize the microwave dissipation behaviors in the sample and optimize the dimensions of the material in microwave heating.IntroductionMicrowave has been applied in materials processing for its distinguished advantages including rapid heat transfer, volumetric and selective heating [1,2]. However, most research work involving microwave heating are confined to non-magnetic materials (e.g. ceramics), with limited attention paid to the heating of mixed property materials (e.g. magnetite and other ferrites) under microwave irradiation [3-5]. Since many magnetic materials exhibit good and even better microwave absorption capability than non-magnetic counterparts, it is quite necessary and deserved to take advantage of this property and then improve the heating efficiency. To achieve this aim, further understanding on the microwave heating mechanism, especially the microwave propagation/dissipation behaviors in magnetic materials is required.The dissipation behavior of microwave in materials has been identified as one of the key factors that affect the efficiency of heating under microwave irradiation and this behavior can be characterized by several parameters. Apart from traditional penetration depth (TEM power penetration depth, Dp = 1/(2*a), where a is the TEM field attenuation factor), two other parameters, field attenuation length (Df) and half-power depth (Dh), are also applied to indicate the microwave dissipation in materials [6].The accurate determination of such parameters can help in optimizing the dimensions of the load in a microwave furnace, producing more uniform heating under microwave irradiation and avoiding thermal runaway."

Jan 1, 2011

By Tim McMahon

"A slurry is any combination of liquids and solids where solids make up more than 10 percent of the mixture. Mining operations create various types of slurries from processes such as dewatering, bitumen extraction in oil sands, concentrator plants, milling operations, tailings, lime addition and so on. The mines then transport these slurries through pipelines (Fig. 1).Slurry valves are used when the mine needs to transport ore a long distance and there are no other viable transportation methods, such as roads or railroads.Severe service valves must be used in slurry applications and they must be tested to ensure reliability. This article describes how Emerson designs and tests its Fisher valves for use in mining slurry applications.Slurry pipeline valvesWithin a slurry pipeline system, valves are required as part of the pumping stations, choking stations and isolation stations. There may be multiple pumping stations depending on the length of the pipeline or the terrain it crosses. Choking stations are used to reduce the velocity and the pressure in the pipeline, either before a pumping station or at the end of the pipeline, and to ensure the pipeline does not slack (remains full and pressurized). Isolation stations exist so that a pig (a device sent through a pipeline to clean or inspect the pipe) can be inserted or removed from the pipeline.Typical valves used in a slurry pipeline are severe service ball valves. The valves use floating balls that are held between the seats and are not pinned or permanently attached to the shaft that rotates the ball. The inside diameter of the ball typically matches the pipeline inside diameter, enabling the pipeline to be cleaned or inspected with a pig.They can be built to accommodate the high pressures required for the typical slurry pipeline. These pressures can require up to ASME Class 2500 valves and flanges. The valves can get qlarge, up to NPS 36 inches.Specialized segmented ball valves and slurry knife gate valves are also used in some slurry applications when pressures are lower, in the ASME Class 150-300 range."

Sep 1, 2019

Edwin H. MessiteR, New Pork City (communication to the Secretary*):—Under the heading " Flues," Mr. Edwards refers to the Bee-hive construction, a cross-section of which is shown in Fig. 4 of his paper. A flue similar to this was designed by me about six years ago,' in which the walls though much thinner than those described by Mr. Edwards gave entire satisfaction. These walls, from 2.25 in. thick throughout in the smaller flues, to 3.25 in. in the larger, were built by plastering the cement mortar on expanded-metal lath without the use of any forms, or cribs, whatever, at a cost of labor generally less then $1 per sq. yd. of wall. Of course, where plasterers cannot be obtained on reasonable terms, the cement can be molded between wooden forms, though it is difficult to see how it can be done with an interior core only as stated by Mr. Edwards. In regard to the effect of sulphur dioxide and furnace-gases on the cement, I have found that, in certain cases, this is a matter which must be given very careful attention. Where there is sufficient heat to prevent the existence of condensed moisture inside of the flue, there is apparently no action whatever on the cement, but if the concrete is wet, it is rapidly affected by these gases. At points near the furnaces there is generally sufficient heat not only to prevent internal condensation of the aqueous vapor always present in the gases, but also to evaporate water from rain or snow falling on the outside of the flue. Further along, a point is reached where rain-water will percolate through minute cracks caused by expansion and contraction, and reach the interior, even though internal condensation does not occur there in dry weather. From this point to the end of the flue the roof must be coated on the outside with asphalt paint or other impervious material. In very long flues a point may be reached where moisture will condense on the inside of the malls in cold weather. From this point to

Jan 1, 1905