Search Documents

By J. P. Hansen

The Bureau of Mines has investigated the S02 leaching of MgO from high-MgO-bearing Florida phosphate concentrates. The S02 was effective in leaching some of the MgO from three phosphate concentrates; flow rate of the S02 and leach time were major factors in determining the amount of MgO leached. Calcining the samples, then grinding to minus 200 mesh, and elevating the leach temperature gave only small increases in the amount of MgO leached. The research also showed that some of the MgO was so intimately associated with the phosphate mineral that it could not be removed by S02 leaching. This amounted to about 0.6, 0.7, and 1.0 pct MgO in three leached residues. The calculated heads for the three concentrate samples averaged 1.4, 1.1, and 1.5 pct MgO, respectively, before leaching.

Jan 1, 1985

By W. E. Lamont

The Federal Bureau of Mines, in cooperation with phosphate companies in the Florida land-pebble area, made a comprehensive study of the waste clays, or "phosphate slimes," produced in the mining of phosphate rock in Florida. These slimes represent a significant ecological problem and a major deterrent to effective land recovery in the phosphate-mining areas. Physical, chemical, and mineralogical studies were made of slime samples submitted by 15 of the 16 plants in Florida in an effort to identify factors that prevent successful consolidation of the slimes and subsequent recovery of the mined lands. Results of these studies indicated that the clay mineral attapulgite, a hydrated magnesium silicate, was primarily responsible for the very poor settling characteristics of the slimes, and that the quantity of attapulgite in the slimes effectively controlled the settling rate, pulp density of terminal solids, viscosity, percent solids of filter cake, and flocculant requirements.

Jan 1, 1975

By R. J. Sweigard

Three case studies were undertaken to investigate the role of land use potential evaluation in reclamation planning and to determine the impact of regional differences on the evaluation process. The three surface mines studied were representative of operations in the Appalachian, Interior, and Northern Great Plains provinces. The scope of the investigations included a survey of regional characteristics, a detailed investigation of the mining operations and site conditions, and an assessment of local land use planning activities in the area of the mine. Special attention was given to key factors that presently determine the use of reclaimed land. Also, for each case study, the postmining land use potential was evaluated using site planning principles. Specifically, the environmental, economic, and social impacts of several potential postmining land use plans were considered.

Jan 1, 1983

By Clarence O. Babcock

Model pillars of limestone, marble, sandstone, and granite having length to diameter ratios of 3:1, 2:1, 1:1, and 0.5:1 were broken in axial compression to determine whether lateral end constraint affected the breaking strength. Steel rings bonded to the ends of the model pillars with epoxy provided, during the loading cycle, a lateral end constraint of about 17 to 30 percent of the average axial stress. The effect of this constraint was to increase the breaking strength of the rock as compared to cylindrical pillars without constraint. The percentage increase in breaking strength varied with rock type and increased as the length to diameter ratio decreased. The maximum increase in breaking strength was 35 percent for marble pillars having a length to diameter ratio of 0.5:1. A theory was developed which relates the expected constraint to the physical properties of the ring and rock.

Jan 1, 1968

By M. H. Staia

A Venezuelan ilmenite concentrate has been chlorinated at a temperature of 700" C by carbon tetrachloride. In the experimental rig, built at laboratory level, the direct chlorination process yielded a TiCI, recovery of approximately 85% after 280 minutes processing. The partial pressure of carbon tetrachloride was nearly atmospheric (0.94 atm). Product vapors from the reactor were fractionally condensed in a condenser which was maintained at a temperature of 250°C meanwhile TiCl, vapors were condensed in refrigerated coils at a temperature of -20°C. The concentrate used in this investigation was obtained by applying gravitational and magnetic concentration methods to the black sands. The experimental results have shown the need to asses the influence of the weight ratio of ilmenite to carbon tetrachloride on the resultant products. The equilibrium of the heterogeneous system has been calculated taking into account the initial experimental conditions.

Jan 1, 1995

By J. S. Kennedy, R. G. Omeara

Beryllium is a strategic metal of ever-increasing peacetime importance because of the unusual properties of beryllium-copper alloys. These unusual characteristics are the combination of high strength and hardness, high fatigue resistance, and high wear resistance in alloys that have the corrosion resistance of copper. The principal industrial source of beryllium is the mineral beryl, a beryllium-aluminum silicate that occurs in pegmatites associated with quartz, feldspar, mica, and smaller amounts of various accessory minerals. The beryl is usually recovered in processing the pegmatites for the recovery of some of the other mineral constituents. Pegmatite deposits are found in various parts of the United States, but those in the Black Hills of South Dakota are the source of most of domestic production. The beryl marketed from the South Dakota pegmatite deposits occurs as coarse crystals, which are obtained by hand sorting. These pegmatites also contain other valuable minerals.

Jan 1, 1948

By A. Van den Steen

In the early fifties Professor Breckpot of the Louvain University in Belgium in collaboration with the Research Laboratory of Metallurgie Hoboken, discovered the possibility to separate nickel from cobalt sulfate solutions by a nickel sulfide depolarized cementation. This reaction, completed later with a zinc precipitation, was developed into purification processes for the Shituru and Luilu Gécamines cobalt plants in Zaíre. Due to increasing demand for higher quality products and the necessity of lowering the production costs, more laboratory and pilot plant investigations concerning the key parameters for the nickel and zinc sulfides precipitation were under- taken. Especially the relative stabilities of cobalt, nickel and zinc sulfides, precipitated with elemental sulfur or sodium hydrosulfide, were examined in relatlon with the pH and with the redox potential. These investigations have led to better plant practice and new development possibilities. The valorisation of the precipitated sulfides has also been considered.

Jan 1, 1988

By Yun Guo, Min-Min Lin, Bing Xie, Hong-Yi Li

The extraction of vanadium from vanadium-containing APV-precipitated wastewater by W/O microemulsion system was studied. In the N263/n-heptane/isoamyl alcohol/NaCl microemulsion system, N263 played double functions of cationic surfactant and extractant to form microemulsion in n-heptane, and isoamyl alcohol was added in the microemulsion as a cosurfactant. The extraction of vanadium by W/O microemulsion systems effectively accelerated the extraction and improved the extractatability because of the enormous increase in the micro-interfacial surface area. Due to ion association with extractant, vanadium was extracted into the microemulsion phase. The influence of different parameters on the extraction ratio (E%) were investigated, including the volume ratio of aqueous phase to microemulsion, surfactant concentration, pH value of the feed solutions, cosurfactant concentration, extraction time as well as temperature. In optimum conditions, the extraction ratio (E%) can reach 97.2%.

Mar 1, 2018

By Peng ZANG, Qihang Liu

Experimental work was conducted to determine the relationships of coal char conversion with temperature and heat absorption. The results show that at an earlier stage of the coke forming process, lump coal would absorb large amounts of heat but the increase of high temperature strength of lump coal was not significant. Contrarily, the lump coal’s high temperature strength was greatly improved at later stage of coke forming process. A number of residual coal was found in most tuyere coke samples illustrating that the lump coals added in the melter gasifier were not completely transformed into coke when they arrived at the tuyere region. The results indicate that the improvement of lump coal’s high temperature performance is limited in the melting gasifier by the low coke forming rate which could become the core factor of fines generation of lump coal in the melting gasifier.

Jan 1, 2016

By J. K. Williams, M. P. Wells

"As part of the planning system at each division of Nchanga Consolidated Copper Mines, Limited, the Mine Planning Department is required to produce a detailed production schedule for each shaft.Because of the difficulties in producing a schedule which satisfies all the mining constraints, and because of the large clerical effort involved, the full range of possible schedules can never be considered.It has been found possible to produce a schedule using linear programming which satisfies the majority of the many varied mining constraints. Computer programs have been written to enable the mine planning department to use this mathematical system without assistance.The system has a large degree of flexibility to enable the planner to include conditions which cannot be incorporated readily in the linear program. This system permits the more efficient production and evaluation of schedules and reduces the amount of clerical effort."

Jan 1, 2014

By F. P. Jung

This presentation will be a general overview of the Cerrejon Coal Project being developed jointly by Carbocol, an entity of the Colombian government, and Intercor, an Exxon affiliate. The word "Cerrajon", by the way, is simply Spanish for a small hill. There is a distinctive hill near the mine site, and it's the only landmark of any significance. It's shown in Figure 1. So the locals call this area "El Cerrejon", "the little hill." Let me start with some of the highlights of the project, summarized in Figure 2, and then go into more detail later. A four-year feasibility study covered the geology, quality, engineering, construction operation and marketing of coal from this region. This study led Exxon to declare the project as commercial in July of 1980. Then in September of 1980 the president of Colombia gave the government's okay to proceed.

Jan 1, 1982

By Min Chen, Lei Xu, Weijun Huang, Shuai Zhang

For the purpose of extending the service life of MgO-C bricks used as linings of vanadium-extraction converters, the effect of Fe addition on properties of MgO-C bricks was investigated. The results showed the addition of Fe could effectively improve the sinterability of the oxidized layer of the MgO-C refractory at 1400°C due to the effect of FeO (formed by oxidation of Fe) on formation of MgO-FeOss and modification of the microstructure, and excellent corrosion resistance against vanadium containing slag was also obtained due to the increase of compactness of the oxidized layer and concentration of FeO in the oxidized layer. Consequently, it is considered that MgO-C brick by introducing the new phase of Fe is a favorable substitute of MgO-C refractory to be used as linings of vanadium-extraction converters.

Jan 1, 2015

By Reda M. Bakeer

"Measurements obtained during load testing of two steel H-piles driven at a site in Northeastern Mississippi are discussed. The general site conditions, equipment used, testing procedures and results of the pile load tests are presented. Both piles were tested in compression and one of the piles was subsequently tested in tension. The piles were instrumented with strain gauges and extensometers to measure the mobilized soil resistance and pile movement. Three different “zero strain” conditions were used to determine the mobilized soil resistance and residual loads due to driving or a load cycle. It was concluded that the effect of residual loads on driven piles could be significant. Driving residual loads influenced the magnitude and distribution of the load transfer curves more than those due to a load cycle. Results of the tension test were impacted by the residual loads from the previous compression test performed on the same pile.INTRODUCTIONSeveral factors affect the performance of a deep foundation system including the subsoil conditions, loading settings, pile type and installation method. Residual stresses develop in piles particularly due to pile driving, but they are typically not accounted for in the analysis (Fellenius 2002). Siegel and McGillivray (2009) presented an assessment of residual loads measured during load testing of instrumented auger-cast-in-place (ACIP) piles. The magnitude and distribution of residual stresses along the pile shaft and toe depend on the pile installation method, previous load cycles and time effects. Poulos (1987) reported that residual load due to driving at the pile toe is independent of pile driving equipment and may significantly affect the results of a pile load test. Hunter and Davisson (1969) reported results of pile load tests performed in compression on fully instrumented piles driven in cohesionless soils along with a discussion of the effects of residual loads. Tension loads of about 445 kN (100 kips) were measured at the pile toe after driving. Unloading residual compression load at the toe was detected as “apparent” tension since the instrumentation was zeroed prior to the test. The researchers suggested a graphical approach to obtain the “corrected” load distribution curves considering that residual load will dissipate following the tension test. Holloway et al. (1975) conducted a study on the effect of residual stresses due to pile driving and developed a computer software that accounts for residual loads. Briaud and Tucker (1984) suggested a method to account for residual loads based on the results of 33 pile load tests performed in mostly cohesionless soils."

Jan 1, 2017

By L. E. Mylting

Modern ash handling systems exist in considerable numbers and a great deal of design and operating experience has been accumulated, It is the endeavor of this paper to point to a number of frequently recurring problems, A general appreciation of these problems will be helpful in both design and operation of systems. The light fly ash and the heavy bottom ash present different problems, and each will therefore be treated separately. Fly ash is collected in the ducting from the furnace to the stack and beneath the mechanical and electrostatic dust collectors. The greatest amount of dust is collected beneath the mechanicals and electrostatics. Hoppers are generally provided as integral parts of the collector. Suitable valves and piping are connected to these hoppers for removal of the dust. The size and shape of these hoppers are important factors in determining frequency of handling and the capacity of the system.

Jan 1, 1958

By D. F. Sherwin

"THE AREA which is described in this paper (Fig. 1) includes the continental margin of eastern Canada extending from the Gulf of Maine to the north edge of the Grand Banks, which, including the continental shelf, slope and rise, comprises an area of about 600,000 square miles. The paper is intended to give a background of the geological setting of this region in the context of its ultimate potential for oil and gas reserves in close proximity to the Nova Scotia energy market.HISTORY OF EXPLORATIONThe history of geological exploration of this area really began in 1878, when U.S. fishing boats brought back samples of rock recovered in trawls from their expeditions to the long-famous fishing banks off Canada's East Coast. Tertiary and Cretaceous fossils recovered from these samples indicated that the eastern Canadian continental shelf was actually the submerged northern extension of the Atlantic Coastal Plain."

Jan 1, 1972

By W. Mbhalati

"Conzal Mine was not meeting production targets in 2013, and it was established that this was caused by the inability of the load haul dump machines (LHDs) to tram the required tonnages. An investigation of the LHD productivity was therefore conducted to identify the inhibiting factors. This was accomplished by carrying out a literature review on LHD operations to gain in-depth knowledge and conducting observations in the working environment. The relevant information and data on the LHD type used at Conzal was also acquired.The major inhibitor was found to be excessively long tramming distances in all the sections of the mine. The one-way tramming distances were all significantly greater than the 90 m set in the mine’s code of practice (COP), with the Main Shafts section having the longest average one-way tramming distance of 260 m. The other inhibitor was LHD utilization, which in 2013 was only 47% against a target of 70%. Simulation of the LHD operation, taking these two factors into account, showed that production could be increased by more than 100%. As a result, it was recommended that conveyor belts should be extended regularly in order to keep tramming distances within the recommended one-way distance of 90 m. In addition, utilization can be improved by minimizing employee absenteeism as well as by modifying the travelling routes such that LHDs do not encounter unnecessary delays.Paper written on project work carried out in partial fulfilment of BSc. (Mining Engineering)"

Jan 1, 2015

By T. Sharma, T. C. Rao

Laboratory studies have been carried out on acid leaching as a possible route for the extraction of potassium from glauconitic sandstone. Leaching efficiencies with sulphuric, hydrochloric and nitric acids were investigated. The effects on potassium dissolution of temperature, concentration and type of acid, stirring speed and leaching time were also studied. The results show that it is possible to recover 87.5, 93 and 85% potassium with 5 M H2SO4, HCl and HNO3, respectively. During the initial stages of the sulphuric acid leaching process the chemical reaction at the mineral surface is the rate determining step, whereas during the later stages diffusion through the product layer is rate-controlling. Overall, the process follows a mixed-control model that includes both chemical reaction and diffusion. The activation energy for the dissolution of K was found to be in the range 25.79-106 kJ/mol.

Jan 12, 1992

By JAMES J. DOUGHERTY

THIS paper is a general discussion of developments in our reverberatory smelting practice during the past five years. It deals briefly kith changes in furnace types ; changes in furnace feed ; de- crease in the amount of slag produced; relation of slag assays to copper loss in the slag; increase in the grade of matte and furnace capacities. The reverberatory is but one unit in the copper plant ancl 'any discussion of it must be considered with reference to the other units and to the plant as a whole. A change in the grade of concentrates at the concentrator puts an entirely new aspect on reverberatory smelting and, likewise, a change in the grade of matte at the reverberatory affects the rate and cost of converting. The introduction of differential flotation in 1927 had a very marked influence on all smelting operations and its effect will be noted

Jan 1, 1930

By Deepu Philip, Pratik Agarwal, Ajay Kumar Shukla, Ishani Shukla, G Rajesh

Steel plants generally employ static BOF end point control models to arrive at a given temperature and chemistry at the end of blow. These end point models have now been supplemented with chaos control models to steer the blowing process in the right direction while the blow is in progress. Merely arriving at the correct end point temperature is however not adequate because in the subsequent stages as well the temperature variations can be large and unpredictable. The present paper deals with an integrated model to take into account the effect of all parameters affecting temperature and composition from tapping to the start of casting to minimize the use of LF or aluminum heating, and also minimize grade mixing. The application of lean operations strategy is explained in which the previous “Push System’ is changed to a “Pull System”, minimizing the use of ladle furnace or aluminum heating during steelmaking.

Jan 1, 2014

By R. K. Young

Producing a sound plant design for a major project requires hundreds of engineers and many drawings. Economical accomplishment of this task is based upon careful and orderly organization of the design team so that at all times there is a complete and workable staff but at no time a surplus of costly talent. This paper will describe the various stages in the development of plant design which normally follow the laboratory and pilot plant investigations discussed in other papers today. An outline of the procedures used in the assembling of a project design group, within an established engineering organization will be presented. Actual procedures may vary according to the size and character of the plant, the special requirements of the owner, and the make-up of the engineering organization performing the design, but most of the points covered will be found to be basic to any plant design project.

Jan 1, 1960