Search Documents

By J. J. Arps

n approach to the study of the electrical properlies of drilling muds, their cakes and their filtrates was made by treating the drilling fluid as a porous medium. Lluring this study it was found that the weight pararneter was omitted from previous investigations on electrical properties. Patnode in 1949 made a similar approach to ,his investigation. His work showed that there was a variation of resistivity relationships with per cent Puid present in a given suspension. This present study ex-tends Patnode's investigation to one in terms of the solids fraction of the drilling fluids. Previous investigations were made on low weight muds where the effect of the rolids fraction was obscured. The following equationr were fitted to data taken from 94 field muds and 47 laboratory muds (see Tables I and 2). The parameter, C, is a complex function of the solidr content, or mud weight, of a drilling fluid. It was also found that for all drilling muds examined. A nomograph is presented combining Eqs. I and 2. INTRODUCTION It is generally recognized that the materials present in drilling muds affect the relationship between mud filtrate and mud resistivities. However, most electric log interpretations proceed with the assumption that the mud resistivity and temperature are the only important parameters needed to obtain a filtrate resistivity or a mud cake resistivity. Lamont1 suggests that only average relationships exist between mud cake, mud filtrate and mud resistivities. He indicates that there is limited accuracy when these intercorrelated factors are used since no other measure-able variable is apparent. A previous paper by Patnode indicates that drilling fluids may be considered to be a system of fluids in solid particles which may be correlated electrically in a manner similar to rock solids. 1 he equation for the resistivity factor. F = (per cent fluid) is satisfied for a given clay type in water, but the value of m varies as different materials are used in the water. The resistivity factor is not constant for a given amount of clay. As is suspected it varies as the solids fraction conducts electrical current. Since both weighting material and clay solids are present in commonly used drilling fluids, it is expected that both materials contribute to the variation of the m factor in Eq. 3. An extension of Patnode's work is presented in this paper to show some of the interrelations which exist between the resistivities of mud cake, mud filtrate and mud. Use of these data enable a more accurate calculation of mud filtrate and mud cake resistivities if only the mud resistivity and weight are measured. EXPERIMENTAL The measurements of mud weight, fluid and solids resistivity, alkalinity, and chloride content of mud samples were made in this research. Mud samples representing drilling fluids from 94 Louisiana and Texas wells (Table 1) and 47 laboratory-constructed systems (Table 2) were used in the experimentation. The measurements of the mud properties were made both in the field and in the laboratory. The tests on the properties of weight, alkalinity and chloride ion were standard tests as described by API specifications. The resistivity measuring devices were constructed in the laboratory for this study. For details on the resistivity equipment see Fig. 1. The fluid cell

By Denni Nikols

"Planning for coal beneficiation in the electric utility industry is relatively complex, involving the coordination of experts and specialists in a broad range of fields, as well as compliance with a wide variety of government regulations.This paper examines the role of the planner, reviews possible benefits of coal beneficiation, identifies potential problems and illustrates a typical planning schedule.The steps involved in the planning process are:Step I-Bench- and pilot- washability studyStep 2- Wash plant designStep 3- Power plant and boiler designStep 4-Mine designStep 5-Major environmental and technical problems to address.IntroductionElectrical utilities and coal have a long and intimate relationship . Cleaned coal is becoming an increasingly popular fuel with the utilities for a variety of reasons. Generally, the greatest impetus to burn a cleaned or prepared coal fuel comes from the need to control airborne pollutants.Long-range planning is a standard practice for electric utilities, forecasts of demand must be made well into the future. Since the lead time required to provide new facilities is often as long as 10 years and the cost very high , planning becomes an important task.For a utility that owns and directs the operation of its coal mines, the mine planning or fuel acquisition planning takes on the magnitude of other corporate planning functions. It is from this perspective that a utility would view coal preparation. Except for the interaction of a coal-fi red plant on the actual mine design the planning considerations o f a beneficiating facility for a captive mine or a contract raw coal supply are about the same. Because TransAlta Utilities is currently supplied from captive mines, this discussion will tend to focus in that direction.It is the role of a planner to plan. This is easy to say but it is not always easy to do. Often we are working within a context that resembles the geological time scale. Frequently the objectives are not clearly defined when we begin and ultimately our plans are tested in the waters of government regulations and cost benefit analyses .Planning for beneficiation of Plains coal, or any coal, provides just such a test. The planner's role in this endeavour requires a wide vision. While parts of the process may be amenable to classical methods of project scheduling, the broad range of subjects and interaction of seemingly unrelated tasks is sure to obscure some of the considerations that must be made. Therefore, the planner's chief role is coordinating the work of many experts and specialists toward the final objective.Among the specialists are combustion , geo technical, mining, civil , and mineral processing engineers , geologists, hydrogeologists, soil, and reclamation experts to list a few.When one considers coal beneficiation, the planning part o f that consideration is probably more complex than any other single engineering function. Due to the company's location in the Alberta Plains and the proximity o f the mine to the thermal generating station, this paper will tend to emphasize that situation.Beneficiation may offer some advantages over run-of-mine coal to the power plant opeator. Some of these advantages are: removal of a contaminant, power plant efficiency gains , lower plant capital costs (for new plants), possible lower mining costs."

Jan 1, 1984

By Boland J

Prediction of rock cuttability by various excavation machines such as tunnel boring machines, road headers, rippers, picks, roller disc cutters, excavators, etc is of major concern to both civil and mining engineers and rock mechanics. In principle, the design of a rock cutting tool is based on achieving maximum excavation with minimum input energy, minimum applied force, minimum equipment weight and volume and, more importantly, minimum tool wear. When a rock material is indented by the force of a cutting tool and then unloaded several material zones form underneath and around the tool. As the tool moves into the rock the volume of its associated rock cavity (ie volume of displaced rock) expands and depending on the indenter's shape various phenomena may occur. Immediately beneath the tool a small zone in which the stress state is more or less hydrostatic, is formed which is underlain by an inelastic, or damaged, material zone. Both size and shape of this damaged zone control the magnitude of the indentation force and the chip formation mechanism during unloading. The rock is unable to store the whole strain energy induced by the tool and consequently the extra energy is expended either in forming new fracture surfaces and/or in plastic deformation in the damaged zone. Therefore, it is not surprising to see that both perfect-elastic and rigid-plastic constitutive models are not generally suitable for modelling indentation of rocks. In contrast elastoplastic constitutive models are more appropriate as they can include both elastic and plastic deformations (Kral et al, 1993). Elastic solutions for several half-space indentation problems can be found in most text books on elasticity and in particular in Timoshenko and Goodier (1951), Sneddon, (1951), Poulos and Davis (1974) and Johnson (1985a). If a failure criterion, eg the Mohr-Coulomb failure criterion, is applied to delimit elastic solutions for indentation problems, a lower bound limit of the applied indentation force (for a given indentation depth) can be estimated. It may be noted that elastic analyses, without any delimiting failure criteria, normally overestimate the indentation force. Plastic solutions for a few indentation problems may be found in Hill (1950), Johnson, (1985a) and Alehossein et al (1992). When analysing the behaviour of indented rocks the choice of an appropriate constitutive model describing effectively the behaviour of the rock at various stages and phases during indentation is a challenging issue. Several questions need to be answered before starting an effective analysis. The first question is of course: Which one of these is more appropriate for modelling zones underneath and around a cutter, elasticity or plasticity theory, continuum damage mechanics or fracture mechanics, and what is the bridging link between these various theories? Which mode is more dominant in fracturing rock, tensile or shear mode? What governs the mechanism of chip formation? What is the function, shape and the behaviour of the pulverised zone that forms just underneath a cutter? Is the hydrostatic stress state assumption reasonable for this zone? How does the rock change during the absorption and dissipation of the input energy and how does the indentation energy vary with rock type and depth of penetration? How can we model the damaged zone under the indenter? Furthermore does a plastic material form beneath the pulverised zone? When and how do radial and ring cracks form around and under an indenter?

Jan 1, 1995

By Robert L. Lagace, Michael A. Grossman, Alfred G. Emslie

This supplement to the final report is a collection of interim and monthly reports and working memoranda prepared during the course of this program to document the progress, methods and results of the work. The supplement is divided into the self-contained sections briefly described below. I. SELECTED MONTHLY TECHNICAL LETTER REPORTS - This section is a collection of selected monthly technical letter reports that briefly summarizes the chronological development of the analyses and results, including the different concepts, theoretical approaches, and methods of data reduction and analysis explored, and the discoveries, insights and findings made along the way. More detailed treatments of the key developments and results are presented in the interim reports and working memoranda reproduced in subsequent sections of this supplementary report, and in the separately published final report. II. BACKGROUND THEORY FOR MEASUREMENT PROGRAM ON MEDIUM AND HIGH FREQUENCY RADIO TRANSMISSION IN COAL SEAMS - Working Memorandum - This working memorandum gives the initial background theory needed to guide the planned measurements and data analyses of this program to describe the propagation of radio waves-in coal seams for the frequency range of 50 to 5000 kHz. III. MODELLING AND DATA ANALYSIS OF IN-MINE ELECTROMAGNETIC WAVE PROPAGATION - Interim Report - This interim report presents detailed treatments of the data analysis and modelling techniques used, and the associated results obtained from conductor-free area propagation data measured by T. Cory in the first set of six coal mines. The mines were located in three highcoal seams; the Pittsburgh seam in northern West Virginia, the Pocahontas No. 3 seam in Virginia, and the Herrin No. 6 seam in Illinois. IV. ANALYSIS OF MF PROPAGATION DATA FROM MARGARET NO. 11, NANTY GLO, EHRENFELD, AND ADRIAN COAL MINES - Interim Report - This interim report presents detailed treatments of several improved data analysis and Modelling methods applied to, and results obtained from, conductor-free area propagation data measured by T. Cory in the second set of four coal mines. These mines were located in three low-coal seams; the Upper Freeport seam in Pennsylvania and West Virginia and the Lower Freeport and Lower Kittaning seams in Pennsylvania. In addition, this report contains a reprint of two papers presented at a Bureau of Mines sponsored EM Guided Waves in Mine Environments Workshop held in Boulder Colorado. One paper describes the three-layer theoretical model and its application to the conductor-free data from the first six mines, while the second paper describes the theory developed for the coupling of loop antennas to a cable in a mine tunnel in a coal seam, and the model's application to data in the vicinity of cables taken at the Margaret No. 11 mine. V. A METHOD FOR NONINTRUSIVE, IN-SITU MEASUREMENT OF COAL AND ROCK CONDUCTIVITIES IN A COAL MINE TUNNEL - Working Memorandum - This working memorandum briefly describes a possible direct method, and its potential advantages and shortcomings, for performing in-situ measurements of coal and rock conductivities. VI. MODELLING AND DATA ANALYSIS OF IN-MINE ELECTROMAGNETIC WAVE PROPAGATION FROM 50 to 5000 kHz - Interim Report - This interim report presents a summary comparison of theoretical and experimental results for conductor- free areas in eleven coal mines located in seven coal seams. It also summarizes the findings and their implications for intrinsically-safe, portable radio communications between roving miners.

Jan 2, 1980

By Russell G. Warncke

"This report is based primarily on a study of safety conditions and practices followed in the coal mines of Japan. Not all of the coal fields in Japan were studied, but typical mines in the largest producing areas and a fair cross section of coal-mine-safety conditions observed during February to April 1948 are described.Information was obtained through investigations conducted in the mines, discussions with mine-management officials and representatives of labor unions of the various mines visited, and examination of records and statistics from the various offices of the Coal Board of the Ministry of Commerce and Industry and from the Coal Association of Japan. Statistical data covering the same subject, obtained from different sources, varied in many respects and apparently were reported inaccurately, but such discrepancies can be attributed to different methods of reporting and compiling statistics.It is difficult to correlate the high fatal and nonfatal injury rates that prevail in Japanese coal mines with the conditions observed in the mines. Virtually all mines visited were attempting to prevent accidents and explosions, by apparently following known safety precautions for the prevention thereof. Some commendable safety innovations were observed at several mines; they indicated that mine officials are giving thought and consideration to hazardous conditions that affect their particular mines.Naturally, the operating officials and management were anxious to impress the writer with their interest in accident prevention and safety. Operating officials were found to be receptive to safety and wore interested in formulating definite safety programs. Some nines had well-planned and well-organized safety programs, which, if put into effect, would contribute greatly toward reduction of accidents.The approach to safety in Japan is quite different from that in the United States, especially the concept of personal responsibility for accidents and the extent to which the individual should be protected against hazards. Management is responsible for providing and maintaining safe working conditions. Collaboration between management and worker, as understood in the United States, does not exist in Japan.Increase in accidents since the cessation of hostilities is the result of unsettled economic conditions in the coal industry, influx of inexperience workers, and breakdown of discipline among the miners, who have been organized into unions. Those unions are greatly influenced by ""leftist"" tendencies.It was observed that the Japanese mine worker is fatalistic by nature and has little, if any, noticable safety consciousness. The most urgent major requirements to reduce accidents in the coal mines are to train the worker in accident prevention and instruct him regarding the inherent hazards of his occupation.Revision of the mining laws would help to reduce accidents if the companies would comply with such laws and provide safer working places and if the workers would cooperate with management and observe and comply with such laws as are enacted for their protection."

Dec 1, 1949

By Rose L. Ballard

This chapter summarizes data on crude nonfuel mineral production for the United States, its island possessions, and the Commonwealth of Puerto Rico. Included also are the tables that show the principal nonfuel mineral commodities exported from and imported into the United States and that compare world and U.S. mineral production. The detailed data from which these tables were derived are contained in the individual commodity chapters of volume I and in the State chapters of volume II of this edition of the Minerals Yearbook. Although crude mineral production may be measured at any of several stages of extraction and processing, the stage bf measurement used in this chapter is what is normally termed "mine output." It usually refers to minerals or ores in the form in which they are first extracted from the ground, but customarily includes the output from auxiliary processing at or near the mines.

Jan 1, 1983

By Xuanxue Mo, Zengqian Hou

"Abstract -Yidun Island Arc in Sanjiang Region is one of the important Kuroko-type volcano­ genic massive sulfide deposits (VMS) districts in southwestern China. Tectonically, the region is situated in the eastern portion of the Tethys orogenic belt, and is a late Triassic extensional island-arc. The island-arc underwent earlier arc construction, intra-arc rifting, later arc construction and back­ arc spreading during its evolution and formed a complete trench-arc-basin system, i.e., the Ganzi­ Litang suture zone, forearc basin, outer arc, intra-arc rifting zone, inner arc and back-arc basin from east to west across the island-arc.Kuroko-type VMS deposits and occurrences discovered so far are limited to within the intra-arc rifting zone of the Yidun Island Arc and tend to occur in groups or clusters distributed in separate fault­ bound basins; e.g., Zengke, Gacun and Xiangcheng basins, in which submarine volcanic rocks, especially bimodal volcanic suites, were extensively developed. The VMS deposits formed in the waning stages of volcanic eruption in the late Triassic and are hosted in the uppermost section of acidic volcanic rocks (rhyolitic-dacitic) within a bimodal suite. The orebodies are associated with these host rocks: rhyolitic-dacitic pyroclastic rocks and exhalites and chemical sedimentary rocks.Ali VMS deposits in Sanjiang are of the Zn-Pb-Cu type. The architecture of the deposits is two­fold, consisting of concordant lenses and layers of massive sulfides and an underlying discordant stockwork. Ali deposits show metal zoning. The hydrothermal alteration related to mineralization is strong and asyrnmetrical, and is found dominantly within the stockwork zone and host rocks surrounding the ores. There are two alteration patterns: (1) chloritization - sericitization - silicification from outer sides to core of the alteration pipe; and (2) silicification + sericitization - silicification + carbonate from the lower to upper part of the alteration pipe_The mineralization temperatures of ore-forming fluids vary in the range 200°C to 335°C. Thermal evolution of the fluids displays temperature profiles that first increase and then decrease with progression of mineralization processes. The majority of black-ore minerais (Groups I and II) formed during intensifying stages of hydrothermal activity, and the majority of serni-yellow-ore minerals (Group III) formed during a thermal maximum . There followed the formation of fine-grained black-ore minerals (Group IV), which interacted with barite layers during decreasing temperature phases.Oxygen and hydrogen isotope studies show that the sources of ore-forming fluids for the Kuroko­ type VMS deposits are two-fold: seawater and magmatic hydrothermal solutions, represented by the Kuroko deposits in Japan and Kuroko-type VMS deposits in Sanjiang, respectively. In the latter case the hydrothermal solutions reacted with host rocks and mixed with cold seawater percolating downward, and circulated through volcanic rocks resulting in development of alteration zones and formation of ore minerals in Kuroko-type VMS deposits."

Jan 1, 1993

By David Berberick

"Hecla Limited’s No. 4 Shaft at the Lucky Friday Mine is the largest capital expenditure in the corporation’s 128-year history and is considered the deepest shaft in the United States. This paper will discuss the project’s history and lessons learned from the initial conceptual design work in 2007 through project commissioning in 2017. Change management was key for the owner, contractors, and vendors in delivering the operational and organizational success on the project. The No. 4 Shaft has extended the life of the Lucky Friday Mine by 21 years to 2039. INTRODUCTION The Lucky Friday Mine of Hecla Mining Company (Figure 1) is the oldest active (77 years) and deepest mine in the Coeur d’Alene mining district, producing approximately 725 tonnes (800 tons) per day from narrow, vertical, silver, lead, and zinc veins. Primary access into the mine is via the Silver Shaft, a 5.5-m (18-ft) diameter, concrete lined shaft sunk to an original depth of 1,890-m (6,200-ft). Current production is from the Gold Hunter vein system, approximately 1,525-m (5,000-ft) northwest of the Silver Shaft.Cut and fill stoping is currently employed at depths to 2.3 km (7,500 ft) below ground surface, making it one of the deepest mines in the western hemisphere. No. 4 Shaft is a 5.5-metre (18-foot) diameter, concrete lined circular shaft, constructed as a 1.2 km (3,860 feet) deep winze in the Lucky Friday Mine. The 2.4 m (8 ft.) diameter, double drum, double clutch, Siemag hoist and associated headworks are situated at the 4760 level, top station at 4940 and shaft stations at 5900, 6500, 6580, 7500, 7580, 8300, 8380, 8500, and 8620. Shaft stations reference depth below Silver Shaft top station. The 4 Shaft was designed, constructed and commissioned over ten years, between 2007 and 2017. Basic design work was completed by Nordmin Engineering, followed by detailed design completed by Cementation Canada. Shaft construction was awarded to Cementation USA and lateral development was initiated in early 2008. Over the course of the next nine years, the project was suspended and restarted twice, dealt with the loss of a miner, added scope including shaft depth and mine infrastructure facilities, experienced squeezing ground that required liner replacement, changed excavation section, and dealt with a final alignment that was not within design requirement for verticality. Hecla and Cementation were successful in delivering a facility that provides fully functional access from collar at 4940 level to shaft bottom at the 8620 level. Two active mining levels below the collar, 5900 and 6500 are accessed. In addition, the shaft provides access to the future mining level at 7500, skip loading facility at 7580 level, station and loading pocket cutouts at 8300 and 8380 levels, spill pocket at 8500 level, and shaft bottom pumping facility at 8620 level (Figure 2)."

Jan 1, 2019

By R. E. Allen, A. C. Jephson

ELECTROLYTIC zinc plants of the American Smelting and Refining Co. are located adjacent to the present city limits of Corpus Christi, Texas. The original plant commenced operations during 1942, and is designed for the production of special high grade zinc from zinc sulfide concentrates.' Subsequent changes include the erection of an additional acid plant during 1950, and additions for increased generating and production capacity during 1951. New Electrolytic Plant—The new electrolytic plant is a separate unit erected for the treatment of densified fume produced at Asarco plants located in El Paso, Texas and Chihuahua, Mexico. Construction was completed and operation commenced during June, 1953. Decision for the erection of a separate plant for the treatment of densified fume is based on several factors. One of the principal reasons is the assurance of continued production rate of the original plant, which might have been jeopardized by combined treatment of calcine and fume. Of equal importance is the advantage of locating a plant on a site with adequate space for eventual expansion. General Description—The new plant for the treatment of densified fume consists of four main buildings for the following operations: storage and grinding of fume, leaching and purification, electrolyzing and casting, and rectifier units. Auxiliary buildings include a baghouse, reagent storage, and a lunch room. Leaching of ground fume with electrolyte from the cells is a batch type operation in tanks equipped with mechanical agitators and weightometers. Completed leaches are pressure filtered, the resultant residue being recovered for shipment to El Paso by conventional use of thickeners, drum type vacuum filters, and a direct-fired dryer. Filtrates from the filter section are purified in mechanically agitated tanks, filtered after completion through plate and frame presses, and then pumped to an evaporative type cooling tower. Solution discharged from the basin of the cooling tower is collected in storage tanks for use in the cells. The cool purified solutions are pumped as required from storage to the solution circuit for circulation of electrolyte through the cells. Except for the addition of purified feed solution and withdrawal of electrolyte for leaching, the circulating system for the cells is essentially a closed continuous circuit that includes the use of evaporative cooling towers for control of solution temperatures. Aluminum cathodes and Ag-Pb anodes are used for electrolysis, which is maintained at a current density of about 82 amp per sq ft. Cathode zinc produced is melted in a gas-fired reverberatory furnace and then cast into slabs on a straight line casting machine. Unloading and Storage—Fume produced by the Chihuahua plant is shipped in box cars, and fume by the El Paso plant in hopper bottom dump cars. Shipments as received are weighed on a 7 5-ton capacity railroad scale, sampled, and then moved over one of the two unloading hoppers with a car puller. The cars are then unloaded with mechanized equipment, a car scoop being used for unloading of box cars and a car shaker for the hopper bottom cars

Jan 1, 1958

By Ronald Damen, Dion Denes

"Friction fatigue is the loss of soil-pile friction around the shaft area of the pile. It has been observed during impact driving of piles, and has been modelled to a limited degree using physical scale models. This paper proposes the use of high strain dynamic pile testing to assess and quantify friction fatigue in impact driven piles. The method is applied to two case studies: one on a project off the north-west coast of Australia and one on a South Pacific Island. On both sites calcareous sand layers are present. Pile Driving Analyzer (PDA) monitoring has been conducted during impact driving of steel piles, which allowed for assessment of shaft resistance development both with depth and with progressive driving, by use of wave equation signal matching. Lessons are drawn from the case studies to improve future observations.INTRODUCTIONFriction fatigue is the loss of soil-pile friction around the shaft area of the pile, under cyclic loading or during pile driving. The phenomenon has been frequently observed in some non-silica sands, such as pumice sands and calcareous sands and has been the subject of academic study.The occurrence of friction fatigue impacts the driving behaviour of piles and the shaft friction component of the ultimate geotechnical strength (Rd,ug). If potential friction fatigue is not recognised in the design phase of a project, required pile toe levels can be significantly underestimated. This could lead to extra cost and delays, or, if no adequate pile verification is conducted, to geotechnical failure or underperformance of piles. This is especially true in remote locations, such as Pacific islands, where calcareous material is often present.A better understanding of the phenomenon would aid both pile design and driveability assessment. This paper proposes the use of high strain dynamic pile testing to assess and quantify the effect of friction fatigue from impact driving. Two case studies are presented in which high strain dynamic testing has been conducted on driven piles in calcareous sands to illustrate the method.BACKGROUNDFriction fatigueThe geotechnical strength of piles is composed of the resistance to static loading by the base of the pile and the shear resistance between the shaft of the pile and the adjacent soil. The latter is often referred to as the shaft resistance or shaft friction.During impact pile driving, a decrease in shaft resistance is often observed. Although this phenomenon is also observed during vibratory pile installation, this paper deals predominantly with impact driving. This decrease in material strength from the tip of the pile influences the shaft resistance and may be either temporary or permanent. Temporary reduction in shaft resistance is common in cohesive soils and is thought to be caused by excess pore water pressure, which has insufficient time to dissipate. This phenomenon, commonly referred to as set up, is observed to a significantly lesser extent in non-cohesive materials such as clean sands (Rausche et al., 2004)."

Jan 1, 1900

By M. Holuszko, I. Mikhalev

"Previous studies described by Galvin et al. (2017) have shown that for Australian bituminous coal fines, both in batch and in continuous process, the new improved oil agglomeration procedure based on the use of high-internal-phase (HIP) emulsions, as compared to the conventional “pure oil” agglomeration process, enables a significant reduction in the amount of oil while reaching a high yield of clean coal (approximately 90% of agglomerates greater than 355 µm in size) in a significantly shorter time. The HIP emulsion used in these experiments comprised up to 95% vol. aqueous solution of sodium chloride (3% wt. concentration) and for the rest, a mixture of kerosene (oil) and sorbitan monooleate (SMO emulsifier) in a 1:1 ratio as a binder. This study evaluates the applicability of the new HIP-oil agglomeration process to treat Canadian bituminous ultra-fine coal and Russian sub-bituminous coal fines and compares results from agglomeration to the flotation response of both coals. Oil agglomeration is known to be sensitive to surface properties of coal. Since surface properties of coals depend not only on the rank of coal but also on their origin (depositional environment) and mineralogical composition, both the applicability of this new improved agglomeration process to the non-Australian coals and its efficiency became the motivation for this study. To evaluate the applicability of the new process to both Canadian bituminous and Russian sub-bituminous coals, a series of bench-scale tests were carried out under conditions similar to those described by van Netten et al. (2016) for the Australian coals. Based on the results obtained in this research, new boundary conditions for the application of the HIP emulsion-based oil agglomeration process have been outlined and conclusions on the viability of the new process to treat ultra-fine coal from Western Canada and Russian sub-bituminous coal fines have been reached.INTRODUCTION In most cases, to meet the market requirements, the mined coal has to be processed to reduce the ash content by the removal of mineral matter and thus to increase the quality of the coal products (van Netten et al., 2016). Generally, flotation is used for processing fines from high rank coals; however, there are high losses of very fine coal due to the inefficiency of this process. Furthermore, difficulty in dewatering the fine coal results in excessive moisture levels causing coal handleability issues, which increases costs in the coal-cleaning industry (Capes & Darcovich, 1984). Much of the development that has occurred in fine coal cleaning has taken place with higher-value coal, often metallurgical (Klima et al., 2012). If the fine coal is deemed to be too difficult or expensive to process, it may be discarded as waste (van Netten et al, 2014). Such disposal not only creates an environmental liability but may also result in the loss of a valuable, high quality product that is better liberated than the coarser fractions of coal."

Jan 1, 2018

By G-L. Wu, S-W. Wu

"The hot deformation behaviour of Nb-Ti microalloyed high-strength steel was investigated. Hot compression tests were conducted in the temperature range 900 to 1100°C under strain rates of 0.1, 1, and 5 s-1. Dynamic recrystallization (DRX) occurs as the main flow softening mechanism at high temperature and low strain rate. The hot deformation activation energy was calculated to be about 404 699 J/mol. The constitutive equation was developed to describe the relationship between peak stress, strain rate, and deformation temperature. The characteristics of DRX at different deformation conditions were extracted from the stressstrain curves using the work hardening parameter. The Cingara-McQueen equation was developed to predict the flow curves up to the peak strain. The processing maps were obtained on the basis of a dynamic materials model. The results predict an instability region in the temperature range 1010 to 1100°C when the strain rate exceeds 0.78 s-1. IntroductionThe 700 MPa grade HSLA steel is widely used in engineering machinery, automotive beams, carriages, and axle tubes, etc. (Pan et al., 2017 ). Generally, such grades contain a moderately high amount of Mn (approx. 1.4% and above), and microalloying elements like Nb, Ti, V, and Mo to impart the desired strength and toughness through solid-solution strengthening, precipitation hardening, and grain refinement dislocation strengthening (Chen and Yu, 2012; Opiela, 2014). However, the production costs can be greatly reduced by replacing part of the Nb, V, or Mo with inexpensive Ti and adopting the compact strip production CSP process (Opiela, 2014; Chen et al., 2015). Furthermore, the microalloying technology coupled with new-generation thermomechanical control processing (NG-TMCP) has proved efficient for achieving the proper balance between strength, toughness, ductility, and formability by means of a suitable combination of chemical composition and thermomechanical treatment parameters (Shukla et al., 2012; Wu, Zhou, and Liu, 2017).In hot forming processes, the complex microstructural evolutions are often induced by multiplicative hot deformation mechanisms, such as work hardening (WH), dynamic recovery (DRV), and dynamic recrystallization (DRX) (Zhang et al., 2014; Liang et al., 2015). Dynamic softening behaviour during hot processing has generated considerable interest because component properties are influenced significantly by its corresponding microstructural evolution (Wu et al., 2010). During deformation in the DRX process, deformed grains are replaced with substructures and newly formed fine and uniformly distributed grains. This occurs only when a critical strain for the onset of DRX is reached, and at the same time, the minimum rate of energy dissipating is reached (Ferdowsi et al., 2014). DRV occurs at a high strain rate and low temperature, reducing the stored energy greatly and making DRX difficult (Liang et al., 2015). The microstructural changes during DRX are sensitive to the processing parameters, such as strain rate, deformation temperature, and strain (Zhang et al., 2014; Ferdowsi et al., 2014). Therefore, in order to optimize the hot processing parameters, it is important to understand the behaviour of hot deformation visà- vis control of microstructural evolution."

May 1, 2019

By F. Bélanger, P. A. Fournier

"Modelling and optimization techniques used in the operation of the Detour Lake Mine leach circuit are contrasted to a 1973 review of contemporary techniques used by a major gold producer. The leach circuit at the Detour Lake Mine was modelled using a full factorial Design of Experiment of stirred tank reactor leach tests using circuit feed. Contour plots of extraction were applied in the plant to optimize addition rates of cyanide and the newly-commissioned lead nitrate system. Contour plot sections were used to understand the impact of sulphur in circuit feed at different operating dissolved oxygen concentrations. The 1973 review paper offers insight into industrially-applied modelling and optimization techniques. In particular, a mathematical model of plant data was developed using multilinear stepwise regression analysis. The model was presented using graphical representations available at the time and applied to optimize the rates of cyanide addition. Off-the-shelf software solutions of today allow mineral processors to quickly and easily visualize data, allowing them to re-allocate time and resources spent processing data to generating raw data and extracting actionable information.IntroductionModelling and optimization in mineral processing is the art of reducing reality through judicious use of assumptions to understand a process and leverage this knowledge to engineer practical solutions to metallurgical problems. Data analysis is at the core of this enterprise.While this paper showcases the modelling work done at the Detour Lake Mine (DLM), the primary objective is to pause and reflect on how far the field has progressed since the 1970’s. A snapshot of state-of-the-art gold cyanidation modelling at that time is a review paper of the Anglo American Group’s capabilities (Brittan & van Vuuren, 1973). The objective of this paper is not a play-by-play of the evolution of modelling and optimization since that time. Rather, it is a comparison of the field at two points in time.In 2016, DLM undertook an extensive bench-scale leach circuit modelling program to better understand the impact of cyanide, dissolved oxygen, lead nitrate, grind size, density, and pH on gold cyanidation (Fournier, 2016). Two major capital expenditure projects were anticipated for 2017: improvements to oxygen control and a lead nitrate distribution system. While the lead nitrate system was planned for construction, the design parameters had not yet been selected. Following the development of the model, plant trials were executed to validate aspects of the model and the methodology was expanded to address other plant issues, in particular the effect of talc chlorite and pyrrhotite in leach feed.The variables of the bench-scale study are summarized in Table 1. Dependent variables were varied using a full factorial design of experiment with two repetitions for each test condition, yielding a total of 300 tests. Test order was randomized to eliminate bias from independent variables."

Jan 1, 2018

By Joël P. T. Kapusta

Although Peirce-Smith converting remains the workhorse in matte converting, the copper and nickel industries are still confronted with production hindrances such as tuyere blockage, excessive refractory wear and limits in the oxygen enrichment levels of the blast air. The knowledge acquired on high-pressure gas injection technology as well as the invention of the concentric tuyere for steelmaking led to the development of the Air Liquide Shrouded Injector (ALSI) technology for copper and nickel converting. Following a technology demonstration in 1997-98 with four shrouded injectors installed in a Peirce-Smith converter, Falconbridge Limited implemented ALSI Technology on a commercial scale in May 1999 as an integral part of its new Slag Make Converter at Sudbury, Ontario, Canada. The paper presents the various aspects of commissioning ALSI Technology, as well as the operating changes and injector design modifications over the five years the shrouded injectors have been in operation.

Jan 1, 2005

By L. Gutierrez, S. Gering, C. Calderon-Arteaga

"INTRODUCTION Drill and blast (DnB) represents the most important, and sometimes the most costly processes in a mine.. The cost of drilling and blasting operations greatly contributes to the “high cost trends of the overall mining operations” (Afum B. O. and Temeng V. A. 2015). The use of available information to improve the DnB processes can be the difference between a highly expensive process and an optimized one. Mining operations have access to several types of data sets and key information from a wide variety of different systems. This information is normally used to improve, evaluate and apply processes for drilling and blasting. This may include different types of data from the different stages of the process (before, during, and after the drilling and blasting operations), such as hole locations (planned and actual), penetration rates, drill operators, fragmentation (expected and resulting), explosive (design and usage), geology, vibration, and others. This information can be used on its own or combined for further analysis to reduce costs, improve safety, and evaluate results. Fortunately, due to advances in mining software, drill and blast engineers can exploit this data and create reports to evaluate results and improve the DnB process. However, as users start combining information from multiple datasets and establishing standard operating procedures for reporting this data across multiple sites, it becomes valuable to create auditable, automated, and sustainable processes for handling the information. In many cases the task of aggregating and standardizing the data formats has already been completed and is available to consumers via the Enterprise Data Warehouse (EDW). A data warehouse team extracts data from the source systems and transforms it so that it is meaningful for decision support (Barbara H. Wixom, Hugh J. Watson, 2007). Our initial implementation plan for the DnB solution included using data stored at the sites; however we learned early on in the process that much of the work for aggregating and supplying the required data was already completed. The goal for this case study is two-fold: to show how information can be used to make decisions and improve processes, highlighting the value of using an EDW for managing Drill&Blast information; and to discuss how technical challenges encountered during the implementations were resolved. This paper is targeted at users that want to better manage their DnB data or try to set up standardized workflows for using this information. This case study will discuss the process of implementing a DnB workflow at multiple sites within Freeport McMoRan Inc (FMI) using both data at the sites and information available using the EDW. The paper will begin with an overview of the project. The discussion will then describe how DnB processes were used to set up daily workflows in order to provide information for evaluating process and making decisions. The final section will discuss some of the technical challenges and how they were solved, as well as possible next steps for further improving the workflow."

Jan 1, 2017

By Qingbo Yu, Qin Qin, Junxiang Liu

"Dry-granulation is a new process of molten blast furnace slag treatment and air is used as heat exchange medium. There are some shortages: poor effectiveness of granulation, high air-slag ratio and high energy consumption, which are the obstacles to popularize dry-granulation. Based on rotary cup atomization, the technique of recovering waste heat of molten blast furnace slag through waste heat boiler producing high pressure steam is exploited. The molten blast furnace slag is granulated to uniform small slag granules with high temperature, and slag granules pour into the waste heat boiler. It could produce steam, obtained in first row and second row tubes, when descending velocity of slag granules equaled 1.1mm/s and the Reynolds number equaled 7100. The application of the system for recovering waste heat from high temperature molten blast furnace slag has a significant meaning.IntroductionBlast furnace slag is one kind of solid waste in iron making process, which is discharged at the temperature range from 1723 to 1923K. In China, there was 0.162 billion tons of slag discharged in 2009, and the energy contained in the slag is equivalent to the energy in 9.4 million tons of coal equivalent. The sensible heat of molten slag is a very valuable waste heat source, so it is worthwhile to recover the sensible heat. At present, the molten slag is treated by a water quenching method. But in this process, the sensible heat is not recovered, moreover, an amount of water is consumed and harmful waste gas is discharged into the environment. Due to the considerations of energy conversation and environmental protection, the iron making industry pays close attention to dry-granulation, which is useful to obtain more benefits [1-4]. The sensible heat is recovered and an amount of water is saved by the method of dry-granulation. The amorphous content of slag granules obtained from dry-granulation is over 95% [5, 6], so the slag granules can be used as a perfect raw material for cement [7, 8].In the late 1970s, the Sumitomo Metal Industries, Ltd. and the Ishikawajima-Harima Heavy Industries, Ltd. jointly undertook the research of rotary drum granulation. This method has several disadvantages: the processing capacity and efficiency are low, and it is not adoptive to operate continuously in production [9]. From 1980, Nippon Steel, NKK, Kawasaki Steel, Kobe Steel, Sumitomo Metal Industries and Nisshin Steel were engaged on air granulation, and the experiments were operated for 6 years on the blast furnace in Nippon Steel. In the process of air granulation, there was great power consumption. The complexity of structure and the great floor space of the air granulation device caused high cost of investment. In 1986, Ukraine exploited a new method of heat recovery referring to the technology of Continuous Casting and Rolling [10]."

Jan 1, 2011

By Gene M. Handel

Today the world is heavily dependent on petroleum for its energy. In the United States, over 75% of the primary energy used comes from petroleum. Other developed countries are similar. The less developed countries have a lower dependence on petroleum just as the United States did through the early 20th Century. However, these less-developed countries look upon petroleum as one of the primary energy sources for the economic growth required to improve their standard of living. So everyone considers petroleum an essential ingredient in the recipe for the good life. But there is a substantial problem with this recipe, and it is finally getting general recognition. Petroleum is a finite resource, and the world is using it up at a rapid, accelerating rate. Though it won't be exhausted for many decades, the early warnings of ultimate limits have already appeared. The suppliers of the incremental production in the Middle East have threatened to restrict increases in their production rates. And, of course, the short term embargo of four years ago clearly demonstrated the economic impact of reduced access to petroleum as a primary source of energy. World petroleum production will probably peak in. 10 to 15 years and then start declining. When that happens, economics--the allocation of scarce products (also known as the dismal science for obvious reasons)--indicates that the price of petroleum will escalate in real terms. So that's the situation today. We have a serious and growing problem facing us that could substantially alter the quality of our life over the next 25 years. Recognition that the society may face a period of lowered expectations after a long period of upward mobility will be a painful experience, but it is certainly not the moral equivalent of war. And, besides, we have time to take positive actions to avert the most serious consequences. When we consider alternate energy sources, the possibilities are almost endless: coal, oil shale, tar sands, solar, fission, fusion, wind, tides, biomass, etc. Actually, the list is endless because new possibilities are continually being proposed. Of these possibilities, coal uniquely stands out as an attractive substitute for petroleum. Coal can be, and is, burned to generate electricity and provide heat. It can be liquefied to supplement the liquid fuels from petroleum, and it can be gasified for use as synthetic natural gas. Unlike exotic alternate energy such as solar and fusion, coal has successfully been used commercially to produce synthetic fuels. But, the technology does need to be refined and modernized. Thus, coal's role is not to be "America's Ace in the Hole," but to bridge the transition from primary dependence on petroleum for energy to the utopia of renewable sources of energy. But don't be mislead by the prophets--those renewable sources of energy are going to be very, very expensive when they are invented.

Jan 1, 1978

By Kendall E. Born

Production of crude oil in Tennessee during 1940 was slightly more than 15,000 bbl., a decrease from 1939 of about 36,000 bbl. This sharp decline has been caused largely by curtailed activities in the shallow pools in Clay County, where approximately 3000 bbl. was marketed off the lease during the year as against more than 37,000 bbl. in 1939. The flashy production found in 1938 in the Celina area has been short-lived and the area is essentially abandoned. Failure to find steady production has been the major factor retarding developments in the northeastern Highland Rim area. The Mississippi lime production in Scott and Morgan Counties continued to show a steady decline. The Tennessee production by counties is shown in Table I. Table i.—Oil Production in Tennessee it1 1940 Production. Bbl. Number of County Wells Pumped 1939 1940 Scott............ 4 4,332 3.596 Morgan.......... I: 6,479 5,751 Fentress.......... 3 I,2XX 1,5xz Pickett........... 1 1.2XX Clay............. 8 37.200 3,XXX Developments There were 32 wells spudded in during 1940, four of which were drilling or only temporarily suspended on Dec. 31, 1940. Twenty-eight wells were completed during the year, four of which were commercial producers. The total footage drilled was 3I,214 ft. The more important wildcats are listed in Table 2; the distribution of 1940 oil and gas tests according to physiographic divisions is given in Table 3. Cumberland Platenu.—Thcre was one completion in the coal area of the state, a test that attempted to extend the Mississippi lime production in the Coon Hollow pool to the southeast in Morgan County. This test encountered only slight shows of oil in the producing horizons of the near-by Coon Hollow and Boone Camp pools. Some surface work was carried on by private interests during the year in Scott and Morgan Counties and two wells were spudded in early in 1941 The revival of interest in the Kentucky portion of the plateau will probably result in increased activity in this part of Tennessee during 1941. Several sizable blocks of acreage, some by major oil companies, are held in Scott, Morgan, and Cumberland Counties. Middle Tennessee.—The northeastern Highland Rim continued to be the most active area in the state with 20 completions, although this figure is about one third of the number drilled in 1939. Four oil wells, none with initial productions of more than I00 bbl., were completed in Clay, Fentress, and Pickett Counties. The producing horizons discovered in Pickett and Fentress Counties were in the "Sunny-brookJ' pays of Trenton age. The Clay County producer was an old test drilled deeper in which oil was found at 671 ft. in the upper part of the Stones River group of limestones, a common pay in this area. All four wells were drilled in or close to old shallow production. Deeper testing into the Knox dolomite group in this area was not particularly encouraging, although one well in Fentress County encountered some saturation at 1860 to 1869 ft. in the upper

Jan 1, 1941

By Louise Barton Freeman, Iley B. Browning, Coleman D. Hunter

During 1942, production of oil in Kentucky reached a total of 4,169,163 bbl. of which 1,807,809 bbl. came from eastern Kentucky. This was more than a million barrels less than in 1941, owing partly to the low price of crude oil, which almost eliminated wildcatting, and partly to spacing regulations, which limited the number of wells drilled in small, shallow pools where the pressures are not sufficient to maintain maximum recovery in widely spaced wells. In eastern Kentucky much of the oil was produced from outliers of the Mauch Chunk series at the disconformable contact of the Mississippian and Pennsylvanian. Although wells producing from this horizon, known as the Maxon, are sprinkled over the entire area, the greatest concentrations are in Martin, Floyd, Knott and Pike Counties. A new 30 to 40-bbl. well has been completed in this formation in ,Pike County, where the carbon ratio is so high that ordinarily oil would not be expected. Pike County is one of the largest producers of Maxon gas, and the offset well to this oil well produced gas. Of the 412 gas wells drilled in Pike County, 12.2 per cent produced gas from the Maxon horizon. During 1942, the old Menifee " Cornif-erous" field, the Mariba-Denniston field, was redrilled between old wells, and although it did not produce any large amount of oil it did contribute 2018 bbl. In the oldest oil field in eastern Kentucky, the Ragland pool, operators are cleaning out abandoned wells and are using this oil for fuel oil. There is a possibility that some of this may be used in the future as distilled fuel oil. Eight wells were completed in 1942 in the Jackson County gas field. The development of Jackson County, which was started in 1934 and in which commercial quantities of gas were encountered at a depth of 1100 to 1200 ft., has become of importance in 1942 with the completion of eight wells, making a total of 24 commercial producing wells with an average rock pressure of 140 lb. At this time the gas is not being marketed. In the last year it has been found that these wells, which produce from the Niagaran dolomite ("Cornif-erous"), respond to acidizing and the production has been thus greatly increased. There has been less development in Estill and Lee Counties than for several years. Two wells were drilled in Greenup County, one of which had a show of oil in the Berea sandstone. One deep test, drilled by the Owens-Libbey-Owens Co. in Lawrence County, was dry. This well was drilled to a depth of 4975 ft. into the top of the Clinton shale sequence. Of the 202 wells completed in Floyd, Martin, Knott and Pike Counties, 187 were gas wells, 3 oil wells and 12 dry holes. In Floyd County 66 per cent of the gas production was from the Devonian-Mis-sissippian black shales, 53 per cent in Martin, 79 per cent in Knott and 65 per cent in Pike. This is probably the largest continuous gas field east of the Mississippi

Jan 1, 1943

By Iley B. Browning, Louise Barton Freeman, Coleman D. Hunter

During 1942, production of oil in Kentucky reached a total of 4,169,163 bbl. of which 1,807,809 bbl. came from eastern Kentucky. This was more than a million barrels less than in 1941, owing partly to the low price of crude oil, which almost eliminated wildcatting, and partly to spacing regulations, which limited the number of wells drilled in small, shallow pools where the pressures are not sufficient to maintain maximum recovery in widely spaced wells. In eastern Kentucky much of the oil was produced from outliers of the Mauch Chunk series at the disconformable contact of the Mississippian and Pennsylvanian. Although wells producing from this horizon, known as the Maxon, are sprinkled over the entire area, the greatest concentrations are in Martin, Floyd, Knott and Pike Counties. A new 30 to 40-bbl. well has been completed in this formation in ,Pike County, where the carbon ratio is so high that ordinarily oil would not be expected. Pike County is one of the largest producers of Maxon gas, and the offset well to this oil well produced gas. Of the 412 gas wells drilled in Pike County, 12.2 per cent produced gas from the Maxon horizon. During 1942, the old Menifee " Cornif-erous" field, the Mariba-Denniston field, was redrilled between old wells, and although it did not produce any large amount of oil it did contribute 2018 bbl. In the oldest oil field in eastern Kentucky, the Ragland pool, operators are cleaning out abandoned wells and are using this oil for fuel oil. There is a possibility that some of this may be used in the future as distilled fuel oil. Eight wells were completed in 1942 in the Jackson County gas field. The development of Jackson County, which was started in 1934 and in which commercial quantities of gas were encountered at a depth of 1100 to 1200 ft., has become of importance in 1942 with the completion of eight wells, making a total of 24 commercial producing wells with an average rock pressure of 140 lb. At this time the gas is not being marketed. In the last year it has been found that these wells, which produce from the Niagaran dolomite ("Cornif-erous"), respond to acidizing and the production has been thus greatly increased. There has been less development in Estill and Lee Counties than for several years. Two wells were drilled in Greenup County, one of which had a show of oil in the Berea sandstone. One deep test, drilled by the Owens-Libbey-Owens Co. in Lawrence County, was dry. This well was drilled to a depth of 4975 ft. into the top of the Clinton shale sequence. Of the 202 wells completed in Floyd, Martin, Knott and Pike Counties, 187 were gas wells, 3 oil wells and 12 dry holes. In Floyd County 66 per cent of the gas production was from the Devonian-Mis-sissippian black shales, 53 per cent in Martin, 79 per cent in Knott and 65 per cent in Pike. This is probably the largest continuous gas field east of the Mississippi

Jan 1, 1943