Search Documents

By R. F. Krueger

Results are presented from tests of dynamic fluid-loss rates to cores from clay-gel water-base drilling fluids containing different commercial fluid-loss control agents (CMC, polyacrylate or smt,ch), organic viscosity reducers (quebracho and complex metal lignosulfonate) and oil at several different levels of concentration. In the dynamic system the most effective individual additives to the clay-gel drilling fluid, based on cost-equalized concentrutiom, were found to be starch and the viscosity reducers. These results do not conform with the rankings determined by API fluid-loss rests, which indicate CMC, polyacrylate and starch to be the most effective and comparable. Generally, minimum dynamic fluid-losr rates were attained at cost-equalized concentrations of additive (including thinner) of about $1.00/ bbl, or less. For chernically treated clay-gel drilling fluids, both the standard and the high-pressure API filter-loss tests were found to he inaccurate indicators of trends in dynamic fluid-loss rates under the test conditions used, particulurly for drilling muds containing viscosity reducers. From a practical field viewpoint, restrictions on the applicability of the API fluid-loss test are such that it is open to question whether or not results of this test can be used routinely with confidence as an indicator of control of down-hole fluid loss under field treating conditions. INTRODUCTION The petroleum industry spends large sums of money during drilling operations to control the fluid-loss properties of drilling fluids based on the standard API filter-loss test,' which is a static filtration system. Laboratory studies' ' of dynamic filtration have shown that in a given time period filtrate loss from a circulating mud stream is greater than from a static system and that it is a function of linear mud velocity, pressure and the properties of the drilling fluid. Ferguson and Klotz' and Horner, et al," observed that (I) the dynamic fluid-loss rates for the drilling fluids used were not related to the extrapolated API filter loss and (2) the drilling fluids with the lowest API filter losses did not have the lowest dynamic fluid-loss rates. However, there has been no published information on the relative effects on dynamic fluid-loss rate as a given drilling fluid is treated with increasing amounts of chemical additive to reduce the API filter loss. Such information is economically important because drilling-fluid costs rise rapidly as chemical requirements increase. This paper presents the results of a study of dynamic filtratioi rates to cores from a clay-gel water-base drilling fluid treated with various commercial viscosity reducers and chemical fluid-loss control agents. The dynamic fluid-. loss rates to cores are compared with the standard API filter-loss values at several different levels of additive concentration. Dynamic filtration rates were obtained in each experiment under two different simulated wellbore conditions: (1) filtration just above the bit through a new mud cake laid down dynamically on a freshly drilled formation and (2) filtration up-hole through a mud cake formed by deposition of a static filter cake on top of the initial dynamically formed cake. The latter case corresponds to the bottom-hole conditions existing above the bit when mud circulation is restarted after a stand of pipe has been added or a round trip has been made to change the bit. Except for the short-duration, high-rate filtration beneath the bit where no mud cake can form, these two conditions probably represent the two extremes of dynamic filtration. Because thickness of a dynamic mud cake formed on freshly exposed formation is limited by the shearing action of the mud stream, the filtration rate for this condition is high. On the other hand, once circulation is stopped and a static mud cake forms on top of the dynamic cake, re-starting circulation has only a small effect on the cake properties and filtration rate is much lower thereafter. A discussion of the mechanics of mud-cake deposition and dynamic filtration is outside the scope of this paper but may be found in more detail in publications by prior investigators. APPARATUS AND EXPERIMENTAL CONDITIONS The test equipment used to simulate the dynamic flow conditions existing during drilling was a modification of that described previously by Krueger and Vogel: A schematic flow diagram is shown in Fig. 1. In general, a power-driven, high-pressure mud pump capable of delivering up to 60 gallmin was used to circulate drilling fluid parallel to the faces of 1-in. diameter sandstone cores mounted in a 2 3/4-in. ID high-pressure test cell. Pump rates were controlled by means of a magnetic clutch to maintain an average axial fluid velocity of 110 ft/min in the annular space between the cell wall and a 1 1/2-in. rod positioned on the center line of the cell. The core specimens were Berea sandstone plugs sealed with plastic inside 1 1/8-in. OD tubes and were fluid-saturated prior to use. Burettes were used to accumulate fluid discharged from the cores. The mud sump shown was used for treatment and storage of the drilling-fluid samples during a particular test. The valve arrangement permitted either (1) circulating drilling fluid through the by-pass line while treating with

By H. B. Humphrey

In the 39 years from 1891 to 1929 , gas and dust explosions in the coal mines of Tennessee caused 413 deaths , or one- third of the fatalities in the mines for that period . Inasmuch as explosions caused but about 15 per cent of mine fatalities for the whole United States for this same period it is evident that the Tennessee coal mining record is by no means good , as far as explosion fatalities are concerned . Since 1926 , Tennessee has had a clear record as to fatalities from explosions ; this fact may be credited very largely to the improved conditions and safer practices in Tennessee's coal mines which have been brought about by the work of the State Inspection Department and of the Southern Appalachian Coal Operators Association directed toward adoption of safety precautions and practices most of which are advocated by the United States Bureau of Mines . Chief among these improvements are the replacement of black powder and dynamite by permissible explosives , improved ventilation , and the installation of rigid methods of inspection for gas . With the present tendency for operations to pass into the hands of responsible and informed management , and with unrelaxed care and inspection , the good record of the past several years should be maintained .

Apr 1, 1931

By W. Shockley

THIS lecture can best begin with a statement of the chief conclusion: The metallurgical industry will find profit in supporting fundamental research on dislocations. This support should be done both in their own laboratories and in universities. My lecture consists of an exposition of the basis for this conclusion. The experience on which I base it is drawn largely from two fields in solid state physics—one field is transistor electronics and the other is dislocation theory. At present the relationship of solid state physics to technology is different in these two fields. In electronics without question, the physics has led the technology. In metallurgy, on the other hand, the technology in the form of metallurgical art is far ahead of the fundamental science. In transistor electronics, physics has suggested and can still suggest previously unachieved combinations of matter that will have new and useful properties; that is, the physicist can make specific predictions. The physicist can also have some confidence that the predicted devices will actually come into existence in a matter of months or years and that they will live up to the predictions. In metallurgy, the physicist cannot to a comparable degree make predictions and have the same hope that they will lead to something new and valuable. There are a number of reasons for this difference. The first is simply historical. Transistor physics is young. It may be regarded as dating from the announcement of the transistor, in which case it is about four years old, or from the first real control of semiconductors as materials (this was accomplished largely by metallurgists, by the way) in which case it is about ten years old. Metallurgical art, on the other hand, is thousands of years old. There is no doubt that the advance of this art has been and will be hastened by a good fundamental understanding of the quantum theory of atomic phenomena. It, is too much to expect, however, that theory will soon catch up with the lead that practice has gained in a thousand years, and that theory will then point out specific pathways to better materials. It seems more probable that modern atomic theory will serve to interpret and organize information much as thermodynamics has done through phase diagrams. In this lecture, I shall emphasize an important feature common to both solid state electronics and to metallurgy. This common feature is the harmonizing principle that justifies discussing electronics and metallurgy as related topics in solid state physics. In both cases the important properties of the materials arise from imperfections. By imper- fections I mean deviations of the materials from perfect single crystals. The imperfections may be of many forms. From the point of view of utility they may be either good or bad, and a given type may be good or bad depending on circumstances. The technical material of my lecture will be divided into two parts. The first will be chiefly concerned with four types of imperfections in germanium crystals. The control of these imperfections makes possible the fabrication of useful electronic devices. A good example of such control is the junction transistor, which I shall discuss from this viewpoint later. The junction transistor, as some of you may have heard, can be used as an amplifier of electrical signals and in a number of respects surpasses what has hitherto been achieved with vacuum tubes. The second part of my technical material will be concerned with dislocations. For about fifteen years the theoretical physicist has had dislocations in mind as the most important kind of imperfection in metals. He has, however, until recently had experimental material of a highly speculative nature to back up his assertions. I am fortunate in the timing of this lecture to be able to describe some recent results that put dislocations on a far more definite basis than has been the case in the past. In fact there are now some experiments which reveal the characteristic properties of dislocations almost as clearly as experiments in transistor physics reveal the properties of holes and electrons, properties that I shall soon describe. It is this advance in the status of dislocations that emboldened me to make my initial assertion that the metallurgical industry will profit from supporting fundamental research on dislocations. Transistor Electronics In order to discuss imperfections in semiconductors, it is necessary to visualize a reference condition that may be regarded as perfect. In the cases of silicon and germanium, which find application in transistor electronics,' the perfect structure is the diamond structure shown in Fig. I. In this structure, each atom is surrounded by four neighbors with which it forms four covalent or electron-pair bonds. These bonds use all of the four valence electrons possessed by each of the silicon or germanium atoms. The electronic structure of the crystal is thus complete and perfect. A crystal of silicon or germanium with a perfect electron-pair bond structure would be an insulator, In order for electrical conduction to occur, it is necessary for imperfections to arise in the electronic structure. In this lecture, I shall discuss four possible imperfections whose symbols and relationships are indicated in Table I. We shall consider first, as an example, a crystal of silicon containing an arsenic atom as an impurity.

Jan 1, 1953

By C. A. Stickels, C. M. Yen

Secondary recrystallization was investigated in vacuum-melted electrolytic iron to which 70 pm N was vacuum-meltedadded. The secondary texture is "near {554}<225>" for material cold-rolled 75 to 90 pct, the sharpness of the texture increasing with increased rolling reduction and with decreased annealing temperature. At reductions of 95 and 97.5 pct the secondary texture is &apos;"near {322)(296)". Both secondary orientations also exist as major components of the primary re-crystallization texture. Development of a strong "near {554) (225)" secondary texture appears to depend on the evolution of the Primary texture to a transition texture depleted in orientations near the secondary orientation before the onset of secondary growth. A variety of qualitative experinzents have been used to show that nitrogen is important in limiling primary grain growth. The presence of nitrogen does not seem essential for the establishment of a transition texture, but a loss of nitrogen during annealing may facilitate growth of grains in the secondary orientation. Secondary grains we shown to form initially at the specimen surface. This is not thought to indicate that surface energies are important in the growth process. It is proposed that the quasi-two-dimensional character of surface grains permits discontinuous growth parallel to the surface before secondary growth of interior grains is possible. An earlier study of recrystallization textures in 90 pct cold-rolled electrolytic iron showed that secondary recrystallization occurred after annealing for several days at 700C1 This type of secondary recrystallization, which had not been reported previously, results in the formation of a strong texture, best described by the indices "near {554}(225)". The purpose of the present work was to investigate the effect of various processing variables on secondary recrystallization in this material and determine the mechanism of secondary grain growth. LITERATURE REVIEW An understanding of the mechanism of a secondary recrystallization process depends on knowing: 1) how grains in the secondary orientation come to be in the primary recrystallization texture; 2) why normal grain growth does not occur; and 3) what factors determine the strength of the secondary texture. For secondary growth of grains of a particular orientation, a certain minimum fraction of the grains must be in that orientation after primary recrystallization. This requirement is apparently satisfied "naturally" in certain systems, i.e., when the primary texture obtained by rolling and recrystallizing material initially randomly oriented contains a sufficient fraction of primaries in the secondary orientation. However, in other cases, e.g., {110}<001> and {100}<001> secondary growth in silicon iron,2 it is necessary to enhance the fraction of primary grains in the secondary orientation by rolling and recrystallizing textured material. In the present case, the "near {554}<225>" orientation is contained within the spread of orientations found in the primary recrystallization texture of iron or bbc iron-base alloys. In systems where the main driving force for secondary growth is the reduction in total grain boundary energy, secondary growth is observed only when normal grain growth is minimized. Four ways in which normal grain growth can be limited are: 1) Limitation by a strong primary texture. When a very strong primary texture consisting of a single component or twin-related components develop, most primary grains are separated from one another by relatively immobile small-angle grain boundaries. The classic instance of this is secondary growth into the primary cube texture in some fcc metals. 2) Limitation by precipitates. Precipitates present in the proper volume fraction with a suitable dispersion will limit primary grain growth. The role of MnS inclusions in impeding normal grain growth in Si-Fe is well-documented.5 3) Limitation by sheet thickness. Normal grain growth slows drastically when the mean grain diameter is of the same order as the sheet thickness. This effect has been used to obtain secondary recrystallization in thin sheets of high-purity silicon iron.&apos; 4) Limitation by solute impurities. It is well-established that certain impurity elements in solution can have a large effect on grain boundary mobility.&apos; However, there does not seem to be any secondary recrystallization process in which primary grain size stabilization has been shown to be due to the drag exerted on grain boundaries by dissolved impurities. In certain systems, e.g., secondary recrystallization in silver,&apos; the means by which normal grain growth is limited has not been identified, and solute-impurity limitation might be suspected. In order to understand the factors which determine secondary texture strength in three-dimensional growth, it is necessary to examine in more detail the current picture of general secondary recrystallization processes. Following Cahn,9 it is assumed that the primary grains have a range of sizes and that secondary growth of one of the large grains in this distribution is possible when it exceeds a critical size with respect to its neighboring grains. The critical size depends on the ratio ?S/?p, where ?s is some sort of average grain boundary energy between the potential secondary and the primary grains and ?p is some sort of average grain boundary energy between primary grains. For a constant primary grain size, the critical size for secondary growth increases as ?$/?p increases. May and Turnbull5 have incorporated the

Jan 1, 1969

By AIME

TO say that Milton Fies has been active in promoting the Southern Research Institute is a masterpiece of understatement. He is a director and trustee who was in on the ground floor when plans were first made for the Institute and since it became an actuality early in 1945 his interest and efforts continue. He talked about it at the last regional meeting of the Birmingham Section of the A.F.A. and has talked all over the South-and when he makes a speech he has really prepared it. He does not try to rival a political spellbinder, but his careful, concise English is always well thought out and to the point. Southern Research might be called his present hobby as it has been for the past two or three years. Another major interest has been his encouragement and training of engineering students. Active in the formation of the Student Chapter of the A.I.M.E. at the University of Alabama, for several years he saw to it that the students had a prominent engineer at each monthly meeting, usually taking them down to Tuscaloosa from Birmingham in his own automobile. He has also been keenly interested in the mining engineering activities at Tuscaloosa, both in the Bureau of Mines and the University.

Jan 1, 1946

By C. C. Nolan

As the size of the mills get larger and the liners get heavier, abetter means had to be found to handle liner replacement. McLellan Industries is famous for their innovative ideas andwas called upon by an engineering company to develop a mill liner crane. The first crane was developed for Similkameen about 1969 to serve a 32&apos; Ø X 14&apos; Long SAG Mill. The next was Island Copper in Port Hardy, B.C., the same size as Similkameen in 1970. At that time, we took existing hydraulic cranes and modified them to meet the mill configuration. In 1973, we developed a completely new approach for the Southern Peru copper mine at Tacna, Peru for a Ball Mill, size 16&apos;-6" Ø X 19&apos; Long. Each installation required a design study to meet the change in mill size, trunnion size, elevation of floor to feed trunnion, area at the feed or discharge end of the mill. We have supplied self-propelled units as well as lift in. When there is no room at the feed end and if the mill has a trunnion overflow discharge, we have the mill supplier provide a structural frame to span the sump and move the mill liner handier into position with the use of the overhead crane or a mobile crane.

Jan 1, 1999

By T. V. Falkie, Robert Stefanko

Much criticism has been directed at the Coal Mine Health and Safety Act of 1969 from many sources, but few specific charges have been leveled, at least publicly. Yet, if the criticism is truly valid and can ever hope to become constructive, the issues must be approached head on. Therefore, the authors consider this an initial article and invite responses from others for contributions in subsequent issues. Dialogue is today&apos;s popular term and perhaps many of the problems associated with the implementation of the Act are the lack of communication between interested parties. There are two criticisms generally made concerning the philosophical approaches taken in the Act. The first is that there is an over-kill in some of the legislation, some provisions are not justified based on past accident history and economic considerations. Generally speaking in this category, no order of priority was considered consistent with safety and economy. The second category includes those situations where new provisions were imposed to improve safety in one area without adequately considering the consequences in another area, let alone the economics of the situation. While the authors do not always agree with the placement of items in these two categories by some industrial representatives, they will give specific examples that they believe may have a certain degree of validity.

Jan 1, 1971

A feasibility study will fail its objective if it does not identify and then correctly assess, all the risks which could have a substantial impact on the financial viability of a project. Before this assessment can be undertaken, one needs to understand the risk profile of the entity which is making the decision about the project. Some of the commonly encountered issues when assessing project risk are related to the problem of not being able to see the wood for the trees. In any risk analysis it is important that conservatism does not strangle a viable project; that the variables are internally consistent with each other, that reality checks are carried out and that appropriate expertise is used. Sensitivity analysis forms a part of the overall project risk assessment; however, it can only test those variables which have already been identified in the financial model. The most useful tool in performing a sensitivity analysis is Monte Carlo simulation. When properly used, it provides a more real world scenario than the simple adjustment of key variables by ¦ 10 per cent one at a time. Monte Carlo can provide valuable information about the robustness of a project. Project risk and sensitivity assessment is prone to the analysis paralysis syndrome. The focus should be on quality rather than quantity.

Jan 1, 1997

By Ian Masters, A. R. Khoei, D. T. Gethin

This paper describes an experimental investigation into the effects of process parameters on product quality during an aluminum recycling process. In order to build a model relating recovery to the process parameter variables and then use the model for prediction, process optimisation, or process control, a historical data analysis is employed by observing patterns in the datalogged information at IMCO Recycling Ltd. In previous work, we emphasised the importance of expressing the results of an experiment quantitatively, by implementation of a Taguchi approach, to facilitate understanding, interpretation and implementation. This research presents the technical tools that are needed to achieve quality improvement in recycling of aluminum. In this study we apply the use of historical data matching through a Taguchi orthogonal analysis, in order to control and improve the quality characteristic. For this purpose, a numerical model is developed to characterise the inputs and outputs of the process. A response surface methodology (RSM) is employed to find a suitable approximation for the true functional relationship between response and the process parameter variables. The method of least squares is used to estimate the approximating polynomials. Subsequently, Taguchi's method is used to determine the relative significance of each of the parameters. Finally, process management software (written in Visual Basic) is described, and its interface with the process modelling and optimisation routines is discussed.

Jan 1, 2000

By Will H. Coghill

[The supply of gravel spar and of acid spar is not well balanced. Gravel spar -- 85 per cent flourspar, 5 per cent silica -- gluts the market, whereas acid spar -- 98 per cent fluorspar, 1 per cent silica -- is somewhat scarce. Hence it is desirable to convert some of the gravel spar into acid spar. Knowledge of this condition prompted the Franklin. Fluorsrar Co. at Paducah. Ky., to enter into cooperation with the U. S. Bureau of Mines and the Missouri School of Mines and Metallurgy to improve the methods of fluorspar, milling so that morn acid spar would be available. The fluorspar company detailed Mr. Omar Greeman for the work. During the course of the investigation, while Mr. Greeman was also doing work for a master&apos;s degree in the School of Mines? an extensive study was made of gravity concentration of fluorspar ores. Decrepitation by heat treatment was also given a laboratory try-out. A part of tie time was spent on flotation; these notes relate only to the flotation. The results of one of the flotation runs is appended. The test was made in a 500-gram mechanical-agitation machine. The sample was ground to 100-mesh in a pebble mill.]

Jan 1, 1928

The Sixty-fifth Congress was a "War Congress." Perhaps nothing else than war work should have been expected of it, but it had time and opportunity to do much more. Engineers have good reason for sorrow over the engineering legislation that died merely because there was no opportunity for a vote. The mineral resources of the public lands of the United States are, except the precious metals, locked away from development. For more than eight years there has been an attempt by both the executive and legislative departments of the nation to secure legislation which, under proper conditions and without detriment to the public interest, will open up these lands for development. After eight years of study, argument, conciliation, and compromise, Congress agreed in conference of the two Houses upon a measure satisfactory to it and to the Executive Department and the final draft was passed by the House of Representatives, but in the Senate it was talked to death by Senator LaFollette of Wisconsin. Some of its proponents plan to, reintroduce the bill identically as agreed to in conference into the 66th Congress, where it is hoped that by reason of its peculiar fate in the 65th Congress it will be regarded in the nature of unfinished business and thus receive early consideration and passage.

Jan 5, 1919

By M. Cambridge

The design process must anticipate all construction and operational conditions and make an allowance for all eventualities. Prevention of failure during operational life, and in some cases post abandonment, requires that a risk assessment is undertaken during the design stage which defines not only the factors of safety to be used but the criteria for the structure during its operating life. These operating criteria should clearly identify the at-risk structures and the inspection and monitoring routines required to ensure compliance with the design objectives. On a mine site, it is the role of mine management to ensure that the operating rules be applied throughout the mine life and that a system of inspection and monitoring procedures be instigated. Where the risks are significant, high-level auditing by an independent engineer will also be required. Within the inspection and auditing framework, the designer needs to incorporate instrumentation to enable the operators and management to confirm that the facility meets the requirements of safety, stability and environmental compliance whilst continuing to meet its operational function. This paper reviews the use of inspection and monitoring to prevent failure and provides, in summary, examples of where monitoring has been undertaken and prevented failure. A tabulated review of legislation, regulations and technical guidance generated as a result of previous failures or untoward events is provided.

Jan 1, 2005

By P D. Katsabanis, L Liu

Numerical modelling of fragmentation and throw is used to provide information on practical blast design parameters. The function of airdecking and its practical implications, the importance of the initiation point and aspect ratio of cratering charges and the timing between adjacent blastholes are investigated. Accuracy requirements for detonators are discussed with emphasis placed on the volume and fragmentation of the blasted rock, and compared to experimental results. Practical guidelines which have been based on intuition are examined using the model. Some of the predictions have been tested and correlate well with experimental results, obtained in the laboratory. Findings show that a minimum airdeck length is needed to realize any benefit from the application of airdecking in production blasting while the process can enhance the shock energy provided by non-ideal explosives significantly, bottom initiation of charges is beneficial to fragmentation and the aspect ratio for cratering charges can exceed the traditionally accepted ratio of 6. Regarding timing, in the ease of cratering charges, true simultaneous initiation shows beneficial results for the volume of blasted rock; however the accuracy required for practical detonators is very high. Fragmentation improves after a certain delay time while the optimum can be achieved at a range of delays. Timing affects muckpile shape; however it appears that subtle differences in delay times do not have a significant effect.

Jan 1, 1997

The Institute conducts jointly with the American Society of Civil Engineers, &apos;American Society of Mechanical Engineers and American Institute of Electrical Engineers, certain activities as listed below, and is joint owner with them if certain properties. United Engineering. Trustees, Inc. When Mr. Carnegie made his gift which made possible a home for the engineering societies, a separate corporation was organized to act as a holding company and to manage the common property. This was long known as the United Engineering Society but the name has now been changed to one which more nearly reflects the real function of the corporation. It holds title to the Engineering societies Building and to various funds placed in its charge and is managed by a Board of Trustees of which three are chosen by each of the four societies, American Institute of Mining and Metallurgical Engineers, American Society of Mechanical Engineers, American Institute of Electrical Engineers and American Society of Civil Engineers, which own equal and undivided interests in the property. The land and building cost two million dollars. The interest of each of the Founders societies, aside from especial trust funds, is now valued at $493,352. The A. I. M. E. trustees are Arthur S. Dwight, J. V. N. Don and George D. Barron. The President of the Board is Francis Lee Stuart and the Secretary, Alfred D. Flinn.

Jan 1, 1929

By G. H. Clevenger

Discussion of the paper of ALLAN J. CLARK presented at the San Francisco meeting, September 1915, and printed in Bulletin No. 103, July, 1905, pp. 1381 to 1398. G. H. CLEVENGER, Palo Alto, Cal.-Since the precipitation of extremely dilute solutions as regards cyanide presents one of the greatest problems of zinc-dust precipitation, I should like to ask Mr. Clark the minimum concentration in cyanide of the solution from which it is possible to precipitate satisfactorily the gold with zinc dust in Homestake practice. A. J. CLARK.-For a day&apos;s work about 0.015 per cent. That is precipitating a very low-grade solution, very low in alkalinity. It requires probably 0.2 lb. of zinc dust to the ton. JOHN A. FULTON, Melones, Cal.-At the Melones mine, we have been working very low-grade rock for a number of years, the process being amalgamation and concentration up to the last year. The value of the ore increased so that we had to supplement the concentration with a sand and slime plant. Classification was a problem, since to install classifiers would mean tearing the mill all to pieces. We are therefore making use of a Wilfley table for this purpose. The amount of wash water is increased and a stream of fresh water is also run into the feed box at the

Jan 12, 1915

By A. G. Metcalfe

THE failure to detect any change in the thermal properties of cobalt at the Curie point would appear to indicate that the apparatus may have a limited sensitivity. The Curie temperature has been determined by direct methods to be 1121+3°CP and 1131°C.3 The specific heat has been determined many times&apos;.&apos; and weighted values are given in Table I. The allotropic transformations in iron and titanium, used by the authors to test the experiment method, involved a volume change of the order of 3 pct on going from the close-packed to the body-centered-cubic lattice. These energy changes are likely to be much larger than those involved in a diffusionless transformation from a hexagonal to a cubic-close-packed lattice. However, it has been pointed out that thermal observations are unreliable in the detection of phase changes when these are near a Curie point.&apos; James 0. McCaldin and Pol Duwez (authors&apos; reply)—The sensitivity of the present technique is limited to first-order transformations, so that gradual changes in specific heat, e.g., in the vicinity of Curie points, are not detected. Furthermore, the existence of first-order transformations with latent heats much smaller than those occurring in the known allotropic transformations of iron and titanium is, we agree, still pending.

Jan 1, 1956

By J. B. Mackintosh

Some months ago I received a sample of a highly crystalline product occurring in the hearth of the shaft-furnace used in smelting the roasted niccoliferous pyrrhotite at Mr. Joseph Wharton&apos;s works near the Gap Mine, Lancaster County, Pa. Mr. Wharton first observed this product in cavities in the concretions in these furnaces about the year 1870, and published a description of it in that year.* Thinking that it might show some analogy to meteoric iron, he sent the present sample to Mr. George a F. Kunz, who turned it over to me, with the request that I should analyze it at my convenience. The results do not show the expected analogy, because the sulphur in meteoric iron is combined as FeS., while in this product there is only one-sixth the necessary amount of sulphur, which, however, seems to be combined with all the metallic elements present, forming a sub-sulphide of definite composition. I am informed by Mr. Wharton that he has had for a long time the sample which I have analyzed, and that it probably is about the same age as that which he first described. It is worthy of note that the material does not show any signs of oxidation, but that the crystals preserve a brilliant metallic lustre. The first two analyses, made by Mr. J. Voigt, are those given by

Jan 1, 1888

ALEXANDER BRYDEN Alexander Bryden, clean of engineers in the anthracite mining field, and a member of the pioneer Pittston family, was claimed by death Wednesday, September 26, 1917. The announcement was not a surprise, as he had been in a critical condition for several days. Mr. Bryden had been in failing health for a year past, but his indomitable will kept him at his accustomed duties until quite recently. Two weeks before his death he attended the regular weekly meeting of the Board of Directors of the Miners&apos; Savings Bank in Pittston, Pa. At that time he apparently felt that his end was fast approaching, as he bade farewell to his associates on the bank board. Until a few days before the end, he continued to give attention to business matters at his home, in preparation for the end, which he met unflinchingly. In the passing of Mr. Bryden, northeastern Pennsylvania loses one of the best-known mining engineers, and the community, a man who, throughout his long life, was actively interested in its social welfare and business prosperity. He was for many years prominent in the management of the mining operations of the Pennsylvania Coal Co., and at the time of his death held the position of consulting engineer of the Pennsylvania and Hillside Coal. Companies.

Jan 12, 1917

By Ray Everson, Henry Kasaini

"Adsorption of Pd (II) anions on the surface of activated carbon (Norit 0.8) occurred at high proton concentration (0.01 – 2.5M, HCl) in the feed and averaged 27 mg/g. The adsorption process was interpreted in terms of surface ionisation and adsorption model. Enthalpy of adsorption averaged 0.4 kJ/mole indicative of an instantaneous physical adsorption process. We found that the Toth isotherm fit the adsorption data fairly accurately. A combination of the Langmuir and Freundlich equations yields an effective three-parameter Toth equation (1) which is frequently used to describe adsorption on heterogeneous surfaces.Figure 1 shows the comparison between experimental results and the model isotherms. We found that Langmuir isotherms underestimated the adsorption capacity on the porous surface while the Freundlich isotherm overestimated adsorption. Furthermore, the surface coverage at equilibrium was well described by both the Langmuir and Toth isotherms. But, Freundlich isotherm predicted a surface fraction coverage that was higher than unit. Based on better prediction of surface coverage and a reasonable fit to adsorption data, we concluded that the Toth isotherm best described the adsorption data of palladium. The adsorption process was limited by mass transfer resistance through the external film. We estimated the rate constant from equation (2), where e, ?b, and rp are porosity, fluid density and particle radius, respectively"

Jan 1, 2003

The Institute conducts jointly with the American Society of Civil Engineers, American Society of Mechanical Engineers and American Institute of Electrical Engineers, certain activities as listed below, and is joint owner with them of certain properties. United Engineering Trustees, Inc. When Mr. Carnegie made his gift which made possible a home for the engineering societies, a separate corporation was organized to act as a holding company and to manage the common property. This was long known as the United Engineering Society, but the name has now been changed to one which more nearly reflects the real function of the corporation. It holds title to the Engineering Societies Building and to various funds placed in its charge and is managed by a Board of Trustees, of which three are chosen by each of the four societies, American Institute of Mining and Metallurgical Engineers, American Society of Mechanical Engineers, American Institute of Electrical Engineers and American Society of Civil Engineers, which have equal and undivided interests in the property. The land and building cost two million dollars. The interest of the Founders societies, aside from especial trust funds, is now valued at $1,987,793. The A. I. M. E. trustees are William H. Bassett, H. G. Moulton and R. M. Roosevelt. The President of the Board is Harold V. Coes and the Secretary, Alfred D. Flinn.

Jan 1, 1934