Search Documents

By R. Wharton, M. Bagley

The paper reviews the likely introduction of a European directive covering the sale of pyrotechnic articles in member states of the European Union. The background and structure of the directive are described, together with the range of products covered (which includes fireworks, theatrical pyrotechnics, vehicle airbags and seat belt pretensioners, and certain cartridges). Possible timescales and the implications for industry are also discussed.

Jan 1, 2007

By R. T. Grant, C. Bazin, D. Hodouin

It is shown that most of the variation in the results of semi-batch flotation tests is related to the unavoidably stochastic nature of the flotation process. The preparation and analysis of flotation samples and, to some extent, operator error in performing the flotation test procedure are responsible for a small proportion of the observed variability of the calculated flotation performance indices

Jun 17, 1905

By Unknown

Contact Local Law Enforcement Authorities. Contacting the local law enforcement authorities is essential to the quick recovery of explosives taken in a crime. Contact Local ATF Office. The local ATF office will work with the local law enforcement authorities investigating the theft. They can also assist in the preparation of the Theft/Loss Report for submission to the U.S. Bomb Data Center.

Jan 1, 2009

By Tom Bilson

TO recover the remaining ore tonnages along the south side of the Inspiration orebody, the company began open-pit operations in early 1948 in addition to underground mining. Due to the differences in elevation between the orebody and the existing ore handling and treating plants, the truck haulage operation is up hill. Road grades were established at 7 pct maximum.

Jan 8, 1951

By T. F. Witherbee

THE following calculation of heat requirement covers the working of the furnace from January 25th to February 14th, inclusive. A short time previous to the first date the furnace had been working rather badly, so that 300 lbs. of ore and 500 lbs. of limestone were taken off. Within the time mentioned the quality of the iron passed

Jan 1, 1877

By T. F. Witherbee

The following calculation of heat requirement covers the working of the furnace from January 25th to February 14th, inclusive. A short time previous to the first date the furnace had been working rather badly, so that 300 lbs. of ore and 500 lbs. of limestone were taken off. Within the time mentioned the quality of the iron passed

By W. B. Mather

Literature dealing with rock drilling presents a mass of conflicting data. The principal cause of the confusion is attributed to varying definitions of the hardness factor of rock and cutting media. The future development of more efficient drilling methods demands that this problem be solved. The first step in the solution is the compilation of complete data on the physical properties of rocks.

Jan 2, 1951

By M. Ghiani, R. Ciccu

After a short review of the basic concepts underlying the application of selective flotation and electrostatic separation to the beneficiation of phosphate ores, the paper deals with the results obtained with these two technologies for a number of run-of-mine ores of different origin and distinct mineropetrographic features. Problems are discussed in the light of the minero-petrographic characteristics of the ores.

Jan 1, 1993

By William Kent

During the discussions at the Philadelphia meeting in February last;) several speakers expressed their doubts of the general accuracy of chemical analyses of steel made by "iron works chemists," and especially of determinations of manganese. Since the meeting, the discussion of the " practical value of chemical analyses" has been continued at some length in 'the columns of the Iron Age.

Jan 1, 1882

By W. J. Helfrich, R. A. Dodd

Binary aluminum solid-solution alloys containing various amounts of silver, magnesium, and zinc were prepared by careful directional solidification, and the hydrostatic and X-ray densities were compared. With the exception of the Al(Ag) alloys, the X-ray densities were consistently greater than the hydrostatic measurements, in agreement with earlier observations by Ellwood. In contrast to Ell-wood's interpretation in terms of vacant lattice sites associated with Brillouin zone effects, a tentative explanation based on the existence of solidification microshrinkage was favored. This hypothesis was confirmed by an examination of Al(Zn) alloys prepared by vapor diffusion of zinc into aluminum. The hydrostatic and X-ray densities were now in very close agreement, and it was concluded that the filling of Brillouin zones in aluminum solid-solution alloys does not necessarily result in the formation of defect structures containing an excess of vacant lattice sites. ThE existence of defect structures of the vacancy type in alloys in which the excess vacancies have an electronic rather than a thermal or mechanical, and so forth, origin is well recognized. Examples of incomplete lattices of this type are to be found in the Ni-Al,1-3 Fe-Ni-A1,4 c~-Ni-Al,5 Fe-Cu-Al,= and Co-A17 systems. These defect structures are of a special kind in that the intermediate phases possess an ordered atomic arrangement or superlattice, and in some instances the vacancy concentration may be unusually large, e.g., at 45.25 at. pet Ni in NiA1, approximately 8.8 pet of the lattice sites are unoccupied. Ellwood8-10 has reported similar defect structures in the aluminum solid solution alloys of the Al-Zn and A1-Mg systems and in alloys of the Au-Ni system." In Al(Zn) the (apparent) vacancy concentration rose, somewhat irregularly, to a maximum of about 2 pet vacant sites at 25 at. pet Zn, while in Al(Mg) the (apparent) vacancy concentration increased continuously to 1.7 pet at 15 at. pet Mg. An explanation in terms of Brillouin zone overlap was attempted, although Pearson12 has pointed out the difficulty of reconciling the observations with zone theory. However, the possibility of the effect being caused by the Fermi surface just touching a plane of energy discontinuity inside a prominent Brillouin zone has, in general, been accepted. In fact, Massal-ski13 has interpreted Ellwood's8 observations as confirmation of Leigh's14 theoretically predicted zone overlap occurring at approximately 2.67 electrons per atom. Unfortunately, Massalski was apparently unaware that Ellwood9 had revised his earlier results considerably, and the revised data did not confirm Leigh's analysis. Ellwood's clata were reexamined by the present authors who noted a possible correlation between the percentage defects as a function of alloy composition and the temperature interval of solidification measured from the respective equilibrium diagrams. This suggested an explanation in terms of shrinkage porosity rather than vacant lattice sites, and pointed to the desirability of reexamining appropriate alloy systems using: both Ellwood's method of specimen preparation (casting followed by wrought fabrication) and alternativ'e methods, i.e., diffusion, which might be expected to minimize, or even completely obviate, microporosity. ALLOY PREPARATION 1) Cast Allolys and Aluminum Single Crystals. Al(Ag), Al(Mg;l, and Al(Zn) alloys of various compositions up to 20 at. pet silver, 13.5 at. pet mg, and 30 at. pet Zn were prepared by melting under helium and casting into graphite molds. In the first two systems, the maximum alloying addition was quite close to the limit of solid solubility, but the possibility of transformation to a' during quenching somewhat restricted the suitable Al(Zn) composition range. The alloys were prepared from high-purity aluminum, a lot analysis showing 0.002 wt pet Cu, 0.002 wt pet Fe, and 99.996 wt pet A1 by difference. The silver, magnesium, and zinc were of 99.99+, 99.98+, and 99.998 wt pet respectively. Each composition was analyzed chemically. The as-cast ingots measured 7/16 in. diam and 5 in. length. One in. was removed from the top of the ingot, and the bottom 3 in. was machined to 0.275 in. diam; a point was also machined on the smaller diameter end. The remainder of the original ingot served as a top riser during subsequent remelting and controlled solidification. The machined ingots were now remelted using a Bridgman soft-mold technique to ensure directional solidification and, therefore, a minimum of micro-shrinkage. Alumina powder was used as mold material contained in an alundum thimble, and this crucible was placed in a helium-filled Vycor tube. The assembly was lowered through a suitable temperature gradient at approximately 0.5 in. min-l, and the risered portion of the casting was subsequently removed by sawing.

Jan 1, 1962

By P. G. Shewmon, F. N. Rhines

THE determination of the self-diffusion coefficient of magnesium has been made possible recently by discovery1-1 of a radioactive isotope, Mg28 having a half-life of 21.3 hr,1 and subject to manufacture in useful quantity. In the present research this material was condensed from the vapor phase upon a surface of high purity magnesium. The progress of diffusion of the tracer atoms into polycrystalline magnesium was followed by machining layers and measuring the change in the intensity of radiation as a function of the distance of each layer from the surface. The self-diffusion coefficient was found to be 2.1 X 10-8 sq cm per sec at 627°C, 3.6 X 10-9 sq cm per sec at 551°C, and 4.4 X 10-10sq cm per sec at 468°C; the activation energy is about 32,000 cal per mol. Experimental Procedure Since there was no other published measurement of a diffusion velocity in any magnesium-base material, is was necessary to employ a number of new experimental techniques. The short half-life of Mg28 made it necessary to complete the entire experimental procedure within three or four days. This meant that the work had to be done where a cyclotron was readily accessible and that all operations, prior to the diffusion heat treatment, had to be so designed as to minimize their time requirements. Unusual problems were imposed also by the chemical reactivity of magnesium, its high vapor pressure, and the fact that no satisfactory method for elec-trodepositing magnesium on magnesium is presently available. Finally, the machining and handling of the easily air-borne radioactive-magnesium chips involved certain health hazards, resulting in the need for further experimental restrictions. Preparation of Mg28 The Mg28 was produced in the Carnegie Institute of Technology syncrocyclotron by the neutron spallation of chlorine.5 his involved bombarding a 2 gram crystal of high purity NaCl with a beam of 350 mev protons for a period of 2 hr, after which the crystal was dissolved in warm water and the Mg28 was concentrated and purified by chemical means (see Appendix). About 50 microcuries of Mg28 thus were obtained in the form of magnesium oxinate (8 hydroxyquin-olatc?), which was ignited in air to produce MgO. This in turn was reduced to magnesium metal vapor, by the method of Russell, Taylor, and Cooper," in the vacuum apparatus shown schematically in Fig. 1. Here the essential part is a tantalum ribbon, slightly dished to receive the MgO. The ribbon, pre- viously outgassed at high temperature, is heated to about 1700°C by passing an electric current through it, whereupon tantalum oxide is formed, magnesium vapor is released almost instantaneously, and condensed partly upon the diffusion sample. Diffusion-Sample Preparation: Hot-extruded magnesium rod, 21/32 in. round was used in making the diffusion specimens. The magnesium analyzed as follows: 0.004 pct Al, 0.027 pct Fe, 0.040 pct Mn, 0.0004 pct Cu, 0.0002 pct Ni, and less than 0.01 pct Ca, 0.0004 pct Pb, 0.0011 pct Si, 0.001 pct Sn, and 0.001 pct Zn. A brief study of the crystal texture of this material revealed a sharp fiber texture with the (001) plane roughly parallel to the extrusion axis. Cylindrical samples 1/2 in. long by 5/8 in. were machined from this rod, the end faces dressed on 3/0 emery, and lightly etched with 20 pct HC1 in water. These samples then were annealed for at least twice the intended time of diffusion, at the intended diffusion temperature, in order to stabilize the grain structure at about 1 mm average diameter. The annealing treatments were conducted in argon in the same apparatus and in the same manner as the subsequent diffusion treatments, which will be described presently. Thus, a strain-free plane surface was produced, but there remained a layer of MgO which had largely to be removed before the layer of Mg28 was deposited. Most of this layer was taken off by two light passes over 3/0 emery paper. The balance of the oxide and a thin layer of metal were then removed by etching 5 to 10 min in 4 pct nital (4 pct HNO3 and 96 pct ethyl alcohol) made with absolute alcohol. There followed immediately three quick rinses in: 1-49 1/2 pct methanol, 49 1/2 pct acetone, and 1 pct formic acid, 2-50 pct methanol and 50 pct acetone, and 3-pure benzene. This procedure is essentially that of Sturkey.7 The resulting surface, which was of almost elec-tropolished brightness, remained plane and was free of cold work. It could be kept clean by storing under benzene, or in a desiccator; short exposure

Jan 1, 1955

By G. D. Oxx, L. F. Coffin

The concept of using a phase that is liquid at service temperatures as a component of coatings for refractory metals has been described. The liquid, an alloy of gold and silicon, is retained on a molybdemum surface by a capillary system made of molybdenum disilicide. The coating has the advantage of good thermal shock and has a self-henling chracteristic. In order for highly stressed structures to exceed a service temperature of 2000°F, it has become apparent that a development that does not depend on the traditional iron, cobalt, or nickel-base alloy is needed. Alloys of the refractory metals, i.e., molybdenum, tungsten, tantalum. niobium (colum-bium), and rhenium are potentially useful at extremely high temperatures that more conventional alloys would never be expected to achieve. A new alloy of molybdenum has become available that has a 100-hr rupture strength of 35,000 psi at 2200°F.1 As a result of this work, it may be assumed that a material with adequate mechanical properties at 2200?F is now available. Unfortunately, this alloy and all other known alloys of the refractory metals suffer from not being; serviceable in an oxidizing atmosphere for a very long time. In order to permit general use of refractory metals at high temperatures, it is necessary to prevent destructive oxidation by appropriate alloying or by protective coatings. The liquid phase coating reported here is representative of a concept for the protection of metals that permits higher service temperatures and introduces a new group of materials for selection as coatings. Coating Requirements—Service conditions that represent potential applications for refractory metals vary considerably: however, it is possible to consider two conditions that are usually present. The refractory metal1 component must be heated to the service temperature at least once and usually frequently. When a solid coating is used, usually the coating and basis metal do not have the same coefficient of expansion. This difference causes thermal stress in the coating that is aggravated by rapid heating and cooling and eventually causes coating failure. The second consideration is the probability that there will be damage to the coating by some environmental condition. In jet engines, for example, it is expected that large particles, stones, metal parts, and so forth, will strike a bucket at high speed and cut a hole in the coating. In addition to the above considerations, the coating must also have other fundamental properties. Obviously, it must be oxidation resistant. In addi- tion, it must prevent permeation of oxygen and subsequent oxidation of the basis metal at the interface. Also, diffusion of the basis metal to the outside surface and subsequent oxidation there must be prevented. Finally, the coating must not react with the basis metal to form a weak bond at the interface. It should be noted that the coating need not support a load: it must only remain intact. Liquid Phase Coating Design Factors—In the use of a liquid as a principal coating constituent, it would be expected that the two service conditions mentioned above would be satisfied. A liquid would flow under the influence of the thermal strain developed by coating-basis metal expansion mismatch such that failure from this source would not be expected to occur. It is also probable that the ability of a liquid to flow would provide a self-healing effect. Thus, damage caused by particles in the atmosphere would be repaired. A third advantage is evident in that vapor pressure rather than melting point limits the service temperature. This latter advantage permits use of low melting but oxidation resistant metals such as gold or copper that would be quite useless if the solid state was required. A low viscosity liquid alone. however, is a totally unsuitable coating because it will simply flow off a component, particularly under the influence of a high acceleration field. A method of preventing liquid loss must be devised. In this case, it is desired that the liquid have a low viscosity so that it may easily flow into flaws; thus, raising the viscosity is not a satisfactory solution. One other inherent difficulty is caused by the high mobility of atoms in the liquid state as compared to the solid state. Because of this mobility, it would be expected that gases would diffuse more rapidly through a liquid. It is also probable that the solubility of oxygen in the liquid would be comparatively high. These factors would tend toward rapid permeation of oxygen and oxidation of the substrate. It is most reasonable that this problem could be solved by incorporating a solid phase, which is impermeable to gases, as a component of the coating. To overcome the tendency of a liquid to flow easily, it is possible to use surface tension to advantage. If the surface were made up of a large number of capillary tubes of sufficiently small diameter, then surface tension would hold the liquid even against the acceleration of a centrifugal field.

Jan 1, 1961

By L. W. Emery

Undergrorlnd combustion operations were initiated in a 60-acre Bartlesville sand "shoe-string" reservoir in Allen Connty, Kans., in 1956. Tests in separate patterns were conducted using various co~nbinations of air and recycle gas to propagate combustion fronts from the injection toward the producing wells. These patterns were made up of 6 injection and 20 prodrrcing wells Gas and liquid prorluctiorz from each pattern was measured on an individual-well basis, and comparisons were made between the three patterns to ascertain the relative effects of injected gas composition on production behavior. Breakthrough of the combustion front at a well was characterized by an increase in water production from the well followed by an increase in bottomhole temperatrrre to approximately 250" F. After burning fronts had broken through at five producing wells, operations were terminated in 1960. From the total project approximately 79,000 bbl of oil were produced during thermal operations at a cumulative produced GOR of 23 Mcf/bbl. No appreciable change in the character of the produced crude was observed. Combustion in the reservoir was maintained with injected gas compositions ranging fronz 6 per cent oxygen in recycle gas to 100 per cent air. lnjectiotz of large quantities of recycle gas resulted in higher producing GOR's from offset wells than were measured from a pattern into ~vhich straight air ~vas injected. The air required to move the combustion front through I acre-ft of reservoir was computed to be 20 MMscf. This valrre was found to be relatively independent of the quantities of recycle gas injected. The recovery efficiency from the swept area was esti~izated to be about 59 per cent. Areas swept were similar in shape to tlzose obtained with a laboratory potentiometric model. Samples of sund taken from behind the burning front by coring indicated almost total oil removal from the sand. Petrographic analysis of the core samples indicated that the sand had been heated to peuk temperature of rlbout 1,200" F. No rignificant difference in peak temperature was forrnd in two areas where compositions of injected gas were quite different. Compression costs for thermal recovery were estimated to be $1,20/bhl of produced oil. INTRODUCTION The use of the "forward combustion" process as an oil recovery method has received a great deal of attention. This method involves ignition of the formation in an injection well, followed by propagation of a combustion front through the reservoir. Combustion is maintained by the injection of an oxygen-containing gas to react with reservoir hydrocarbons. As the flame front progresses through the reservoir, oil and formation water are vaporized, driven forward in the gaseous phase and recondensed in the cooler part of the formation. In turn, the condensed fluids push oil into the producing wellbores. Completed field tests of the process were first reported by Kuhn and Koch,' and by Grant and Szasz.' Results from other tests have since been reported by Walter,3 by Moss, White and McNeil,' and by Gates and Ramey." ach of these tests essentially utilized a single injection well surrounded by four or more producing wells. Sinclair Research, Inc., elected to do field experimental work using a number of test patterns in a single field in order that comparisons between various operating schemes could be made. The site selected and purchased in 1955 for this experimental work was a 60-acre Bartlesville sand reservoir located in Allen County, Kans. Combustion operations were initiated in mid-1956. Between that time and termination of the project in mid-1960, combustion fronts were propagated from injection wells to producers in three separate well patterns, using different mixtures of air and recycle gas. The test was terminated before sweep of the three patterns was complete so that information about the effect of combustion on the swept areas could be obtained by coring. Results from the test in the form of injection and producing well performance have been carefully recorded, and these form the general basis for this paper. DESCRIPTION OF RESERVOIR The reservoir in which the combustion tests were conducted is a Bartlesville sand "shoe-string", typical of a number of small reservoirs in Southeastern Kansas. Average reservoir characteristics are shown in Table 1. Fig. 1 is an isopachous map of the producing sand showing the reservoir to be approximately 400-ft wide and 2,500-ft long. Maximum net productive sand thickness is 21 ft. Fig. 2 shows a typical core analysis obtained by coring with water-base mud. The reservoir has no appreciable dip and is closed on the sides by degradation of sand into shale. The main body of sand is heavily laminated with shale stringers, which are not continuous between wells. The main reservoir is overlain by 30 to 40 ft of laminated low-permeability sand and shale streaks. No information is available on the original properties of

By Lok W. Home

INTRODUCTION Today, raise drilling (boring) has become the stan¬dard method of raising throughout the Western world. It is estimated that the majority of raise footage com¬pleted in 1977 was accomplished by the raise drilling method. Extensive replacement of the drill and shoot system by mechanized raise drilling has occurred be¬cause users have recognized one or more of the follow¬ing advantages. In a direct cost per meter comparison, mechanized raise drilling is economically more attractive than drilling and shooting. Mechanized raise drilling offers improved personnel safety over the drilling and shooting method. Mechanized raise drilling is a faster and more predictable method for excavation than is drilling and shooting. The raise cost per unit of length becomes less as the raise length increases, offering greater flexibility in the overall design of mines. Mechanized raise drilling provides a substantial reduction in labor requirements. 6) Mechanized raise drilling improves the working environment. 7) Mechanized raise drilling improves the rock in¬tegrity of round, unblasted raises. Increasing acceptance of the raise drilling technique is enhanced by continuing equipment development. Today, a wide range of machines and capabilities is available, machine drive systems have been improved, reliability has been increased, and cutter technology is being improved quite rapidly. Table 1 lists the four major manufacturers of raise drilling machines, cutters, and reamers, together with the approximate number of machines that each company had in operation at the end of 1977. Although Reed and Smith are major suppliers of reamers and cutters, they do not manufacture the drilling machines. Four or five other relatively minor suppliers have built machines, reamers, and cutters for raise drilling, but they did not have a substantial num¬ber of machines in the field at the end of 1977. MACHINES FOR MECHANIZED RAISE DRILLING There are three principal arrangements for making machine-bored raises. They include the use of standard raise drills, reversible raise drills, and blind-hole or box¬hole raise drills. Standard Raise Drills The standard raise drilling machine is set up on one mine level or on the surface, and a pilot hole is drilled from that level or surface to a level below. When the pilot hole has been drilled, the raise then is reamed back from the lower level to the upper level or the surface. This arrangement is illustrated in Fig. 1. Reversible Raise Drills The reversible raise drilling machine is set up on a lower level of the mine, and a pilot hole is drilled up¬ward to a higher level. The raise then is reamed back from the upper level to the lower level. This arrange¬ment is illustrated in Fig. 2. The machines used for this type of raise drilling normally are capable of being used as standard raise drills. Blind-Hole or Boxhole Raise Drills The blind-hole or boxhole raise drilling machine is set up on a lower level of the mine, and a full diameter raise is bored to a higher level without the use of a pilot hole. This type of machine is illustrated in Fig. 3. Drill Recommendations If access to upper and lower mine levels is equal, the standard raise drill should be used. The complexity of the equipment and associated handling procedures for boxhole drilling far outweigh any mechanical advantage or reduction in the number of operations, provided that access to an upper level is available. If there is good access to a lower level but only limited access to an upper level, the use of a reversible raise drill should be considered. If there is no access to an upper level, a blind-hole or boxhole raise drill is the only practical mechanized system. MACHINE SELECTION There are six major considerations in selecting a machine for raise drilling. These include operating range, cutter loading, machine structure and main¬tenance, drill string configuration, drive system, and automated controls. Operating Range As shown in Table 2 and Figs. 4 through 6, raise drilling machines are available for a wide range of hole sizes. Standard raise drill ratings range from raises of 0.9 m (3 ft) diam and 120 m (400 ft) length up to raises of 3.5 m (12 ft) diam and 900 m (3000 ft) length. Boxhole raise drilling machines are available for raises ranging from 0.9 m (3 ft) to 2 m (6 ft) diam with lengths up to 90 m (300 ft). Table 2 lists, among other criteria, the torque and thrust of typical machines; torque and thrust are the main criteria for analyzing the capacity of a machine. The raise sizes shown in Table 2 assume a condition of medium hard to hard rock formations and optimum cutter loading. The recommended raise size for a given machine can be exceeded when raising softer rock formations or when the operator is willing to accept a lower level of performance; the performance is related directly to the 1093

Jan 1, 1982

By G. B. Clark

One portion of this project was to test a blast shield and to design some features for a novel tunneling method termed the Automated Drill and Blast System (ADBS). The ADBS tunneling concept was developed for the design of an excavation system of greater efficiency than conventional drill, blast, and muck (DBM) systems by minimizing the down time and approaching the non-cyclic efficiency of continuous tunneling by means of small charge blasting. Small charge blasting uses simultaneously detonated, small light charges (less than 200 grams per hole) in four to eight shallow (24 to 36 in. deep) holes usually in a line. Limitation of the total explosive per blast reduced air blast overpressure, fly rock velocity, vibration, and noise. Thus, shielded equipment can remain at the face and a tunnel shield permits support personnel to work outby the shield at all times. The ADBS equipment will be composed of five components: (1) a chassis, upon which is mounted automated mucking equipment, and a frame which carries (2) the hydraulic drill(s), (3) load/blast system(s), and (4) control cab(s). The blast shield may have its own mounting. Ventilation, horizontal, and vertical alignment controls are incorporated in the system. The blast sheild, which protects personnel outby the advance equipment from air blast overpressure, fly rock, and gases, was tested with full scale small charge blasting. A blast shield was designed, fabricated, and tested under conditions anticipated for a working model. The shield was designed to expand to fit the tunnel shape, to seal itself to the tunnel periphery, and to contain air blast, fly rock, and gaseous explosion products. In addition, the shield, which was lined on the inby side with rubber belting, reduced the blast noise level outby the shield to 113 dBA or less, which is very near permissible levels. The test results show conclusively that the shield concept is viable. Based partially on the shield tests, a blast resistant control cab was designed to be located on the equipment chassis inby the blast shield to protect operators during blasting, and to contain all the controls necessary for system operation and safety. The economics of tunnel driving using the ADBS were compared with those of DBM. Four rock types, which determine advance rate, and four cost categories were examined. The results of this analysis are as follows: 1. ADBS advance rate is faster because equipment remains at the face and operation procedes semi-continuously. 2. ADBS bit and explosive cost (which accounts for 4%o of the total advance cost) is higher than for DBM. 3. ADBS equipment cost, on a per foot basis, is lower than for DBM. 4. Due to a reduced labor force, ADBS labor cost is lower than for DBM. 5. Because of the overbreak reduction due to controlled blasting, ADBS tunnel support cost is lower than for DBM. 6. On a per foot basis, total ADBS advance cost is from 17% to 20% lower than for DBM, depending on tunnel diameter and rock type. The small charge method greatly reduces ground vibration, increases personnel safety by limiting excessive fracture, and decreases tunnel support requirements by reducing overbreak. The overall analysis, tests, and results to date show that the Automated Drill and Blast System may be developed into a viable tunnel excavation method. The method also may be adapted to use in the mining of ore. For some types of mining operations, the cyclic nature of conventional drill and blast methods may not be a disadvantage, either where the drilling and mucking may proceed simultaneously or where the operations are carried out in adjacent working faces. The proposed method would find application where continuous methods of excavation are desirable.

Jan 1, 1979

By N. Mungan

Laboratory imbibition and displacement experiments were performed using crude oil and cores drilled with water and preserved under anaerobic conditions. The purpose of these tests was to determine reservoir rock wettability and to find out if more oil could be recovered by use of NaOH solution than by conventional waterflooding. The preserved cores were found to be oil-wet. Contrary to work in the literature, these cores changed to water-wet upon contact with air. After exposure to air for a week, the cores yielded more oil by waterflooding than when preserved under exclusion of air. At reservoir temperature of 160F, flooding the preserved cores with 0.5N NaOH solution recovered more oil than an ordinary wa-terflood, and additional oil when following a waterflood. When the caustic solution was used from the beginning, all the extra oil was obtained before breakthrough; when the caustic followed a conventional waterflood, the extra oil was produced in the form of an oil bank ahead of the injected caustic. The increase in oil recovery resulted from wettability reversal. Also, use of caustic reduced the volume of injection required to flood out the cores. At room temperature, however, the caustic solution did not reverse the wettability and gave no additional oil recovery. Cores which had become water-wet by air exposure or caustic flooding were restored to their original oil-wet state when saturated with crude oil and allowed to equcilibrate at reservoir temperature for two weeks. Therefore, in the absence of preserved cores, it may be possible to restore weathered cores to their original wettability for use in laboratory floods. INTRODUCTION Waterflooding has been in use since 1865, and is by far the simplest of secondary recovery methods. Unfortunately, most waterfloods are inefficient in recovering oil, often leaving half or more of the original oil in place un-recovered. The low oil recovery generally results from low sweep efficiency and low displacement efficiency. Consequently, to increase oil recovery by waterflooding, sweep and displacement efficiencies should be improved. Sweep efficiency is primarily affected by reservoir heterogeneities and mobility ratio, while displacement efficiency is affected by the capillary forces between fluids and rock surfaces. For petroleum reservoirs, the capillary forces are expressed in terms of interfacial tension and wettability. If oil recovery is to be improved significantly in water- flooding, the capillary forces holding the oil in the raervoir porous matrix must be reduced or eliminated. One way to reduce capillary forces is to inject commercial surfactants ahead of the injection water into the reservoir. Laboratory tests of this method have shown no promise of an economical process yet, and no increase in oil recovery was obtained in the field trials which have been reported. Work is continuing in many companies to find surface-active agents which, in workable concentrations, can yield substantial added oil recovery. Another way to change capillary forces operating in petroleum reservoirs is by changing the pH of the injected water. Wagner et al.' showed that change in the pH sometimes activates the surface-active materials natural to some crudes and brings about gross wettability change. Since pH alteration can be obtained with cheap chemicals, such as hydrochloric acid or sodium hydroxide, the process shows promise of being economical in a field application. Pan American Oil Corp. reported oil recovery by use of caustic solution from a flooded-out reservoir.' Their test, conducted at a small additional cost, yielded results which were so sufficiently favorable and encouraging that the wettability reversal flood was expanded to portions of the field not previously flooded.13 It is important to bear in mind that changes in the pH of the water not only can reverse wettability but also can lower the interfacial tension between water and crude oil. Reisberg and Doscher4 have studied the pH dependency of the interfacial tension of Venture crude using sodium hydroxide solutions of various concentrations. Their data show that the interfacial tension was lowered from 23.0 to 0.02 dynes/cm by increasing the NaOH concentration from 0.005 to 0.5 per cent by weight. Thus, the use of NaOH may lead to additional oil recovery due to both wettability reversal and lowering of interfacial tension. Whether alteration of pH results in wettability reversal from oil-wet to water-wet and increases oil recovery depends on wetting properties of the reservoir rock and the crude. This necessitates delicate laboratory experiments, with suitable core and fluid samples from a field. Although many investigators have studied wettability reversal floods in the laboratory,1,2,5,6 these studies have been carried out with synthetic porous media, refined laboratory fluids and surface-active chemicals to simulate the process. The study presented in this paper is the first time that wettability reversal by pH alteration has been accomolished in laboratory core floods using carefully preserved natural cores, live crude and with experiments performed at reservoir pressure and temperature.

Jan 1, 1967

By John Chipman

The concentration of a solute in a dilute ),zetallic solution may be measured by any of several parame- ters including weight percent, atom fraction, atom ratio, and lattice ratio. The ratio of filled to unfilled interstitial sites is useful for interstitial solutes. A variable 2 proportional to this ratio is used as a measuve of concentration. For component 2 irz a bitzary solution z2 = n2/Ym - nz/b) where b is the numberber of interstitial sites per lattice atom. For a t~lul-ticortzporzent solution this becomes zz = n2/(nl + Cvjnj) in which Vj = - l/b for an interstial solute and +1 for a substitulional solute. In the infinitely dilute solution the activity of an interstitial solute 2 is proportional lo z2. At finile concentration the departure from this limiting law is expressed us an activity coefficient, his coefficient is a function of concentra1io)z expressed as tevactiolz coeffcient 8; is analogous to the jark~iliar e£ bul is found to be independent of concentvation in certain solutions for which data are available. It is found that the same equations may be used to express the activity of a nonmetallic solute, sulfur, in liquid solutions of iron containing other solutes, both metallic and nonmetallic. For a nonmetallic solute or for one which strongly increases the actiuity of sulfur, it is convenient to assign arbitvarily a value vj = — 1. When this is done the derivative is found to be constant in each of the ternary solutions studied. The activity coefficient of sulfur in a complex liquid iron solution may be expressed as where nk is a second-order cross product determined in the quaternary solution Fe-S-j-k. The equation is used to calculate tlze activity of sulfur i)z three sevetl- component solutions. IN thermodynamic calculations concerning dilute solutions it is unnecessary to invoke laws and relations which extend across the concentration range to include concentrated solutions. In most binary metallic systems, as arkeen&apos; has recently pointed out, there exist two terminal composition regions of relatively simple behavior, connected by a central region of much greater complexity. When the solute is a nonmetal there is only one such region and in many systems the concentration range is extremely limited. It is the purpose of this paper to suggest a method for the calculation of activities in such a terminal region in which one or more solutes are dissolved in a single solvent of predominantly high concentration. HENRY&apos;S LAW In the usual textbook statement of Henry&apos;s law, concentration is stated in mole fraction. This has the advantage that it makes Henry&apos;s law thermodynamically consistent with Raoult&apos;s law. Since all measures of concentration at infinite dilution are related by simple proportion it follows that mole fraction, molality, atom ratio, weight percent, or any other unit of concentration can be used with the appropriate constant. At finite concentrations, however, calculations based on the law depend upon the unit employed. Deviations from Henry&apos;s law at finite concentrations depend upon the composition variable employed. They are evaluated in terms of activity and interaction coefficients2 which have become familiar features of metallurgical thermodynamics. It is the purpose of this paper to propose a measure of concentration for metallic solutions containing interstitial or nonmetallic solutes by means of which the calculation of activities in complex solutions may be simplified. The discussion will be restricted to free-energy interaction coefficients3 typified by Wagner&apos;s c|a BINARY SOLUTIONS The several measures of concentration which are to be considered are shown in line a of Table I. The corresponding activity coefficients are in line b and the deviation coefficients, sometimes called self-interaction coefficients, are in line c. Henry&apos;s law simply states that the activity coefficient approaches a constant value at infinite dilution. By adoptihg the infinitely dilute solution as the reference state and defining the "Henrian" activity as equal to the concentration in this state, the activity coefficient is always unity at infinite dilution. This convention is far sim~ler and more useful in dilute solution than emploiment of the &apos;Raoultian" activities and it will be used in the following discussion. The several definitions and equations of Table I will be referred to by means of their coordinates in the table. Early observations of deviations from Henry&apos;s law in metallic solutions were shown graphically4 rather than analytically. For the case of sulfur in liquid iron5 the slope of a plot of logfs vs (%S) was constant in the range 0 to 4.8 pct S, indicating constancy of eh2&apos; in Ic. He was proposed by wagnerz and has been widely adopted. The a function of IIIc recently employed by ~arkenl was designed specifically for dilute solutions. Darken has shown that the value of a12 remains essentially constant for many binary solutions within a substantial range of compositions. The atom ratio is directly proportional to the molalitv.<, a conventional measure of concentration. IVb and C served as the basis for smith&apos;s6 classic studies of

Jan 1, 1968

By C. E. Tsoutrelis

A new method for determining rock drillability in diamond drilling is discussed; the method takes into consideration both penetration rate and bit wear. The method is based on drilling a rock specimen under controlled laboratory conditions using a model bit. The technique used for determining the experimental variables is extremely simple, quick, and reliable. Drillability is then determined by the mathematics of drilling. In considering the different factors that affect diamond drilling performance, the nature of the rock to be drilled is of outmost importance since it affects significantly the drilling costs and such other variables as bit type and design, drilling thrust, and bit rotary speed. Many attempts have been made to study this effect by correlating actual drilling performances either to certain physical properties of the rock being drilled1-? or to test drilling data obtained under laboratory conditions.7-13 These attempts were aimed at providing a reliable method of predicting by simple means the expected rock behavior in actual drilling, thus giving the engineer a tool to use in estimating drilling performances and costs in different types of rock. The purpose of this paper is to describe such a method by which rock drillability (a term used in the technical literature to describe rock behavior in drilling) could be determined in diamond drilling. It is believed that the proposed simple and reliable method will cover the need of the mining industry for a workable method of measuring the drillability of rocks. It should be emphasized, however, that since drill-ability depends on the physical properties of rock and each drilling process (diamond, percussive, rotary) is affected by different or partly different rock properties,14-l6 the proposed method of determining rock drillability cannot be extended to the other drilling processes. The results presented in this paper form part of an extensive three-year research program carried out by the author in the laboratories of the Greek Institute of Geology and Subsurface Research. During this period the effects of the physical properties of rocks and of such operational variables as drilling thrust and bit rotary speed in diamond drilling were investigated in detail. DRILLABILITY CONCEPT The literature is not devoid of drillability studies. While there are a number of investigators1,3,5-7,9-0,12-13,17 who have attempted to establish by direct methods (i.e., drilling tests under laboratory conditions) or indirect (i.e., through a physical property of rock) an index from which the drilling performance in a given rock may be estimated, very few6-7,9,12, of the proposed methods seem to be of much practical value to the diamond drilling engineer and none to date has been universally accepted. Commenting on the proposed methods for assessing rock drillability, Fish14 remarks that "for a measure of drillability to be accepted it is essential that penetration rate at a given thrust and bit life are elucidated as otherwise the method is of little value." This statement should be examined in more detail by making use of the penetration rate-drilling time diagram obtained in drilling a rock under constant operational conditions. Furthermore, the merits of using this diagram to describe rock drillability will be pointed out. At the same time reference will be made to this diagram when discussing some previously proposed methods. Fig. 1 illustrates such a diagram for three rocks,A, B, and C, which have been diamond drilled under identical conditions. It is assumed here that rocks A and B have the same initial penetration rate, i.e., VOA = Vog, but since rock B is more abrasive than A, rapid bit wear occurs and as a result the fall of its penetration rate with respect to time is more vigorous than in rock A. This is shown graphically by a steeper V = f(t) (0 curve in this rock than in rock A. Rock C has a lower initial penetration rate, due to higher strength properties16 but since it is not very abrasive, only a slight fall of its penetration rate occurs during drilling (in this category are some limestone and marbles with compressive strength above 1000 kg per sq cm). It follows from the foregoing considerations that the characteristic for each rock curve (I) is a function of (i), the penetration rate of the rock Vo recorded at the instant of commencing drilling, which determines the starting point of the curve (1) on the y-axis and (ii), the abrasive rock properties which determine the rate of fall of Vo with respect to time. Thus, curve (I) provides an actual picture of the rock behavior in drilling for given operational conditions, and it can be used with complete satisfaction to assess rock drillability. It can be seen clearly from Fig. I that proposed methods for assessing rock drillability by measuring the

Jan 1, 1970

By A. W. H. Morris, G. H. Laurie, J. N. Pratt

Using- galvanic cells of the form Sn(liq)/Sn" (LiCl-KC1-SnCl,)/Sn-Ag (alloy), measurements have been made of relative thermodynamic properties of the a, C, E, and liquid phases of the Ag-Sn alloy system. Partial heats of solution of the components in the liquid alloys lzave also been observed by direct cal-orimetric measurement in an isoperibol calorimeter. The thermodynanzic quantities are disczlssed in relation to structural and other properties and the existence of anomalous minor fluctuations in the partial heats and entropies of solution in liquid alloys is tentatively suggested. In the course of a recent electro motive-force study of the thermodynamic properties of Sn-Ag-Pd liquids,&apos; some measurements were also performed on the Ag-Sn binary system. Most previous thermodynamic studies of this system have been concerned with the liquid state. Measurements confined to the limiting heat of solution of silver in liquid tin have been made by many calorimetric workers2 while high-temperature calorimetric measurements of the heats of formation of the full range of liquid alloys are reported in the early work of Kawakami~ (1323°K) and more recently by Wittig and Gehrin~(1248°K). Electromotive-force studies on liquid alloys have been made by Yanko, Drake, and Hovorka&apos; (606" to 686°K; 86 to 99.4 at. pct Sn) and by Frantik and Mc Donald&apos; (900°K; 30 to 90 at. pct Sn). The only known measurements on the solid state are of heats of formation of the a, £, and c phases; these values were obtained using tin-solution calorimetry, at 723"K, by Kleppa,~ whose investigation also yielded heats of formation of liquid alloys containing more than 64 at. pct Sn. The present experiments on the Ag-Sn alloys include a re-examination of the liquid phase and, because of the dearth of free-energy data for the solid state, attempted measurements on the a, c, and E phases. The principal new feature of electromotive-force results obtained for the liquid phase was an indication of anomalous fluctuations in the partial heats and entropies of solution of tin at certain compositions. However, since the values for these thermodynamic quantities were determined from the temperature coefficients of cell potentials, which are commonly subject to considerable error, confirmation by calorimetric measurements was considered desirable. A detailed investigation of the partial heats of solution of the components in the binary liquids was made using a liquid metal solution calorimeter. I) GALVANIC CELL STUDIES a) Experimental Details. Measurements were made, as a function of alloy composition and temperature, of the potentials of reversible galvanic cells of the form: ~n(liq)/~n++/~n-Ag (solid or liquid alloy) Details of the apparatus and experimental techniques have been given elsewhere.&apos; so that a brief account will suffice here. Molten salt, 58 mole pct LiC1-42 mole pct KC1, containing small amounts (1 to 2 mole pct) of stannous chloride was used as the electrolyte. The salts were dehydrated by pre-electrolysis and vacuum -drying techniques. Cells were established under an argon atmosphere by immersing tin and alloy electrodes in the molten salt contained in a large silica tube, heated in a vertical resistance furnace. The tube was sealed at the top by a head plate provided with openings permitting the simultaneous insertion of six electrodes, a central thermocouple sheath, and connections to vacuum and argon lines. Temperatures were controlled to *0.2"C over prolonged periods, with maximum variation over the electrodes at any time of 0.l°C. Temperatures were measured with a standardized Pt/13 pct Rh-Pt couple. The electromotive force of this and the cell potentials were measured on a Cambridge Vernier potentiometer and short-period galvanometer. Alloys were prepared from Pass "S" tin (99.999 pct) and Johnson-Matthey high-purity silver (99.999 pct) by melting in evacuated silica capsules and quenching in cold water. For liquid phase experiments, pieces of the resulting alloys were remelted into prepared silica electrode units, while solid electrodes were prepared by remelting into 3-mm bore tubing, inserting a cleaned molybdenum lead wire, and quenching to produce uniform rods about 3 cm in length, with soundly attached leads. In all cases remelting was done under an argon atmosphere. The solid electrodes were subsequently annealed in evacu ated silica tubes for 14 days at about 20°C below the solidus and quenched. Analyses showed that these techniques produced uniform electrodes with no significant change from weighed out compositions. b) Results and Discussion. Measurements were made on about forty alloys in the solid and liquid states, over varying ranges of temperature between 550" and 1050°K. Stable, mutually consistent, and reproducible electromotive-force data were obtained with most liquid alloys and these are shown in Fig. 1. Investigations were extended below the liquidus tem-

Jan 1, 1967

By J. D. Livingston, H. E. Cline

Cu-Pb alloys in the vicinity of the monotectic composition have been directionally solidified under a high temperature gradient at rates up to 2 X l0-&apos; cm per sec. Over a wide range of compositions, high growth rates yield a composite structure consisting of continuous rods of lead in a copper matrix. This range of compositions increases with increasing growth rate, in agreement with arguments based on the relative velocities of composite growth and the growth of copper dendrites or lead drops. The breakdown of the composite structure at slow growth rates is explained in terms of the relative interphase surface energies. The observed interrod spacings of the composite structure are large compared with the predictions of the Jackson-Hunt equations of eutectic growth. ThE directional solidification of many eutectic alloys produces fine composite structures of parallel lamellae or rods. There has been considerable interest not only in the fundamentals of this two-phase solidification process,&apos;-3 but also in the interesting physical properties produced by such regular and aniso-tropic microstructures. Composite structures can be grown only over a limited range of composition, beyond which coarse primary dendrites of one phase appear. In organic eutec-tics, this composition range of composite structures has been shown to increase with increasing growth rate.7"10 These results were explained in terms of the relative velocities of composite (coupled) growth and dendritic growth. Although similar arguments should apply to metallic eutectics,11-13 suitable experimental results are lacking. In contrast to the work on eutectics, the directional solidification of monotectic alloys has received little attention. (The monotectic reaction is similar to the eutectic reaction, except that one of the resulting phases is a liquid, which subsequently solidifies in a separate reaction at a lower temperature.) Directional solidification of some monotectic alloys&apos;4715 yields regular rodlike microstructures, whereas in other cases macroscopic separation of solid and liquid phases occurs.16 chadwick17 rationalized these results in terms of the probable relative magnitudes of the various interphase surface energies. A recent study of chill-cast Cu-Pb alloys18 revealed a fine rodlike microstructure in alloys near the monotectic composition. It was decided to investigate the directional solidification of such alloys, and to determine the range of composition and growth conditions yielding composite structures. The Cu-Pb system is convenient for such a study, both because it is simple metallurgically, with no compound formation and negligible solid solubilities, and because its basic properties are well-documented. Recent literature on the Cu-Pb system includes studies of bulk thermo-dynamic properties,&apos;g surface energies,20"21 densi-ties,25 and diffusion constants.a6 A similar study of the directional solidification of Cu-Pb alloys was recently undertaken, independently, by Kamio and Oya." EXPERIMENTAL Alloys were prepared by melting 99.999 pct Cu and 99.999 pct Pb in a graphite crucible, stirring well, and pouring into a cold graphite mold. Rods 0.175 in. in diam were machined from the ingots. Alloy compositions studied ranged from 25 to 55 wt pct Pb. Samples were placed in graphite crucibles 5 in. long with 4 in. OD and 0.035-in. walls. They were melted under flowing argon in a vertical, two-zone. platinum -wound furnace. A voltage stabilizer was used to minimize fluctuations in input power. The narrow specimen diameter minimized convection. Directional solidification was achieved by driving the crucible downward into a +-in. hole in a water-cooled copper toroid. The toroid was located immediately below the narrow end zone of the furnace. The end zone was separately powered to maintain high local temperature. Therefore a high temperature gradient (approximately 300 deg per cm) was maintained in the specimen throughout the run. The crucible motion was screw-driven. and a wide range of drive speeds were available. The limited rate of heat removal caused a thermal lag in the specimens at high drive rates. However. temperature-time curves from thermocouples imbedded in a representative sample indicated that the average growth rate still approximately equaled the drive rate. Although the specimens were initially homogeneous, melting and re solidification redistributed the lead. producing composition variations of several percent along the specimen length. (During melting. lead melted first and ran down the sample surface. Rapid freezing tended to reproduce the resulting composition gr~dient, but slow freezing did not because a slow-moving interface tended to reject lead. as discussed later.) To determine local composition. ;-g samples were cut from regions exhibiting various microstructures and were chemically analyzed for lead content. Micrographs were taken on as-polished or lightly etched surfaces. Three-dimensional structure of the lead network was viewed with a scanning electron microscope after removal of some of the copper matrix with nitric acid. RESULTS Several different microstructures are observed, depending on composition and drive rate. Because melting and resolidification produced composition gradients, results are best presented in t&ms of final local composition, rather than initial or average composition. The ranges of local compositions and drive

Jan 1, 1970