Search Documents

By M. W. Grabinsky, J. H. Curran

"Characterizing the spatial distribution of rock stresses is a challenge, especially in the geologically complex environments typically found at most metalliferous mines. Therefore, instead of focusing, specifically, on the task of making stress measurements, the engineer should instead attempt to develop a better understanding of the interaction between stress, mining geometry and rock mass behaviour. This paper demonstrates such an approach using a Canadian Shield hardrock mine case study, in which geomechanical models are used to relate stress, mining geometry, and rock mass properties to observed excavation response, and numerical modelling is used to better quantify this interaction.IntroductionUnderstanding how the mine geometry, field stresses and rock mass interact to produce the observed rock mass response to mining can be a significant challenge. Consider our present ability to quantify the basic geomechanical design input data. Mine geometry is normally quantified in more detail than is required for analysis purposes. Our understanding of rock mass strength and stiffness is far from complete, but established procedures do exist to obtain estimates of these parameters based on index and laboratory testing data and field mapping. Our ability to quantify field stresses is probably the most limited, in part because stress measurements are difficult and expensive to carry out, and in part because the stresses vary to an unknown degree from point to point within the rock mass. The engineer must, therefore, consider whether or not stress measurements are justified and, when they are, where the average stress state needs to be quantified and how many of which type of measurements will be required to determine the average stresses.Such was the case at Ansil mine, a massive sulphide deposit in hard rock located at a depth of more than one kilometre in the northern Québec portion of the Canadian Shield. The Ansil orebody was relatively rich, but small, with the potential for significant stress-related problems. As a result, geomechanical design had to be done carefully from the start – there would be little opportunity to modify the mining strategy once production had begun, and the economic consequences of stope dilution and rock mass instability would be severe. An extensive stress measurement campaign was carried out, but the determined stress magnitudes were unexpectedly low. The designers were, therefore, faced with a dilemma:"

Jan 1, 1997

By Emad Farouz, Francis A. Abreu

"This paper presents a case history of a successful construction-phase pile load test program that optimized the pile design in challenging ground conditions at the Great Neck Wastewater Treatment Plant in the Town of North Hempstead in Nassau County, New York. The improvements and expansion of the wastewater treatment plant included the construction of several new structures to comply with new stringent nitrogen discharge requirements and new design flow. The challenging ground conditions included up to 20-ft thick organic deposits with weight of hammer blow counts and up to 14 percent organic content and tidal ground water that was near the ground surface. The foundation design evaluated various deep foundation alternatives and selected driven closed-ended pipe piles then filled with concrete as the most suitable foundation. The selection process included considerations of cost, risk, vibrations, noise, and schedule. The contract documents utilized an innovative approach of performing an optimization load test program that was implemented during construction to optimize pile lengths and reduce potential vibration and construction schedule.This paper discusses the details of the successful load test program including static testing, dynamic testing, and the innovative contracting approach utilized to implement the construction phase load test program. It also discusses the successful development and implementation of driving criteria for production piles and construction challenges. The successful load test program resulted in savings of several hundred thousand dollars, optimized schedule, and lower environmental impacts.SITE AND PROJECT DESCRIPTIONThe Great Neck Water Pollution Control District (GNWPCD), located in the Town of North Hempstead in Nassau, New York, owns and operates a municipal wastewater treatment plant (WWTP) that discharges treated effluent through an outfall to Manhasset Bay, which is a tributary of the Long Island Sound. The site is located west of Manhasset Bay and is surrounded on three sides by local roads, and commercial, industrial, and recreational properties. The site has a gentle slope ranging from elevation +20 to +7 from west to east, respectively, based on the Nassau County Datum.To comply with new nitrogen discharge requirements and new design flows, the GNWPCD contracted CH2M HILL, Inc. and William F. Cosulich Associates as a Joint- Venture (JV) to design and provide services during construction of eight new advanced nitrogen removal facilities."

Jan 1, 2017

By J. Mikhael Erekson, Connie Campbell Brashear, Brent Meins

Christmas morning 2020, an IED in an RV was detonated along an evacuated section of downtown Nashville, Tennessee. The blast damaged over 40 buildings, including AT&T’s Main Central Office and caused internet and cell outages across 1,200 zip codes for three days including the airport and EMS services. Published investigations by the ATF and FBI were inconclusive in determining the explosive composition and size. Video captured a large fireball that may indicate a fuel-air-mixture explosion which would create lower peak pressures than high explosives, but longer pressure duration and significant impulsive loading. Blast pressures were amplified by reflections in the urban environment bordered by the 8-story AT&T building and a row of multi-story historic buildings. Some structures had little damage as they were shielded from the blast pressure by closer buildings, and seemingly far-field structures contained damage from the pressure wave after multiple reflections and propagation through porous parking garages. Damage to the reinforced concrete frame AT&T building included snapped masonry ties, cracking and spall to the closest column, and vertical displacement of the elevator, even with the brakes applied. The historic structures directly across the street from the blast partially collapsed. Initial damage included complete failures of unreinforced masonry façades, broken timber beams, and uplifted roofs. Secondary, progressive collapse took place over months as the brick walls and weakened historic mortar could not resist typical wind and environment loads. One of the close historic structures was renovated in the 1990’s and structural retrofits to comply with building codes were required. The addition of steel columns and façade tie-ins improved survivability and it remained standing with a high percentage of the front brick intact. Generally, the observed blast damage was related to a structural component’s mass and flexibility. Internal timber framing was unscathed, but many steel studs required replacement. Glazing damage was observed several blocks away and many roof membranes were punctured by falling debris. Secondary damage from broken sprinkler lines and loss of environmental control often led to more costly repairs than the initial blast pressure damage. The proliferation of bomb-making knowledge leads to hundreds of bombings each year in the US. Building risk considerations should include explosive threats along with other hazards. ASCE structural standards and design manuals have been published to address these risks and may be useful guides for building construction.

Feb 6, 2023

By Erik Westman, Benjamin Mirabile

"Quantitative evaluation of secondary support performance in longwall tailgates in U.S. coal mines was introduced with the U.S. Bureau of Mines (USBM) Wood Crib Performance Model. This model evaluated crib performance based on load capacity, stability, and convergence characteristics. The introduction of a large variety of alternative secondary supports in the 1990s prompted a full-scale load-displacement testing program conducted by the USBM and, subsequently, NIOSH. The application of the ground response curve concept to secondary supports provided a more complete estimation of secondary support loading in longwall abutment zones. Secondary support loading from floor heave, horizontal stress effects, and pillar yield are captured by the ground response curve. A point on the ground response curve can be measured by instrumenting a secondary support with load and convergence measurement devices. A segment of the ground response curve can be measured by instrumenting two secondary support types of varying stiffness. Numerical models have been used to construct complete ground response curves for longwall tailgates based on measured secondary support performance. The ground response curve concept can be used as a design methodology for secondary supports in the #2 entry, as well as the longwall tailgate. Extending published evaluation and design methodologies for secondary support in longwall tailgates, a ground response curve unique to the loading conditions and required functionality of the #2 entry can be developed. Numerical models can be used to construct full ground response curves based on measured data in the #2 entry.INTRODUCTIONA longwall ventilation system is designed to continuously dilute and move methane-air mixtures and other contaminants from the active face, to bleeder systems, and out of the mine. The #2 entry of the tailgate gateroad serves to transport contaminated air from the longwall face to the bleeder system. The #2 entry is required to function as an air course between two longwall gobs and is subject to significant ground movement and loading. Current ground support design and evaluation practices are based on empirical evidence and little to no quantitative data on support performance exists for these entries. Substantial volumes of research have been conducted on ground movement and support performance in longwall tailgate entries. Following the successful ground support evaluation and design practices established for longwall tailgate entries, a practical and efficient design methodology can be adapted for supporting the #2 entry of a three-entry gateroad system."

Jan 1, 2018

By Lance Rasband, Richard Hanke

"Seattle Tunnel Partners (STP) started mining on Seattle’s SR99 tunnel on July 30, 2013, working slowly through a 15 ft (4.6 m) thick fiber-reinforced concrete headwall. Once through the headwall, the machine would move through roughly 400 lineal ft (122 m) of jet grout-improved soil at a rate slightly over 6 ft (1.8 m) per day. It was anticipated that once through the improved area, Bertha—the world’s largest tunnel boring machine—would move at a rate of 35 ft (10.7 m) per day. By the end of October 2013, Bertha had mined roughly 430 ft (131 m), averaging 4.73 ft (1.4 m) per day, and had begun mining within native soils. By the start of December 2013, tunneling reached the 800 ft (244 m) mark and Bertha averaged 12 ft (3.7 m) per day, achieving as much as 42 ft (12.8 m) of progress on some days. However, on December 6, 2013, Bertha began to stumble and all progress quickly came to a halt. Preliminary InvestigationInitial reports stated that an obstruction had stopped the machine in its tracks. Malcolm Drilling received an early morning call on Sunday, December 8, 2013, from STP to rapidly mobilize a Bauer BG-50 drill rig with crews to investigate what was hindering Bertha’s progress. Malcolm’s equipment and crews flew into action and were completely mobilized and operational by mid-week. The preliminary investigation involved installation of 10 deep dewatering wells to reduce the hydrostatic head within the ground around the machine and allow STP personnel to inspect the cutter head from within the shaft for presence of obstructions. By the close of December 2013, the wells were installed and the dewatering system was fully commissioned. STP crews were then able to inspect the cutter head and found small fragments of a steel pipe wrapped around the outside of the shield. The steel was apparently from an abandoned 10 in (0.25 m) diameter monitoring well casing previously installed by WSDOT (Washington State Department of Transportation) to monitor groundwater conditions for the design and planning of this very project. After the steel was cut out of the head and cleared from Bertha’s path, she attempted to move forward but was only able to manage a slow crawl"

Jan 1, 2015

By E. Engelbrecht

"A pressure non-oxidative leach is employed at Anglo American Platinum Base Metal Refiners to extract nickel from a slow cooled matte. The design base requires two 80 m3 autoclaves in parallel to achieve a nickel extraction of 60% at the nameplate capacity of 32.4 ktpa nickel plated. Isothermal modelling of mineralogical and chemical concentration profiles, through a reactive mass balance, permitted rate constant parameter estimation and selection of the most probable reaction pathway. The model was validated with plant data up to a capacity of 26 ktpa Ni plated and suggested by extrapolation that nameplate capacity may be viable through one 80 m3 autoclave.INTRODUCTION Anglo American Platinum Base Metal Refiners is situated on the outskirts of Rustenburg in the North-West province of South-Africa. The refinery produces nickel cathode, copper cathode, cobalt sulphate powder, covellite rich copper pressure leach residue and bulk sodium sulphate through an integrated circuit that refines slow cooled converter matte. The converter matte is milled, non-magnetics are separated as solid nickel copper matte (NCM), and the magnetics are leached yielding a pressure vessel liquor (PVL). The remaining solid platinum group metals (PGM) concentrate after leaching is sent for downstream processing in the Precious Metals Refinery (Hofirek & Kerfoot, 1992). The work presented here is applicable to the base metals refinery which receives the two base metals feed stocks NCM and PVL. In 2009 the capacity of the refinery was upgraded from 21 ktpa nickel cathode plated to 32.4 ktpa. This paper deals with evaluating the capacity of the pressurised non-oxidative nickel leach (NOX) process which accounts for at least 28% of the nickel leached from NCM by design. The NOX design base requires two 80 m3 autoclaves divided into four compartments operated in parallel at 155°C and 600kPa(g). Elevated temperature is required to speed up the leach kinetics of particularly nickel and iron which are trapped in slow leaching mineralogical phases namely millerite and bornite, (Dinham, 2006). The stated equivalent capacity for the NOX configuration was 32.9 ktpa nickel plated at first pass nickel and iron leach efficiencies of 60% and above 80% respectively and is a key step for the selective removal of iron (Bryson, Hofirek, Collins, Stiksma, & Bereaowsky, 2008)."

Jan 1, 2017

By A. Rod Kern, Michael A. McNicholas, Yaser Taheri

Deep foundations were required for construction of an 18,000 ft2 (1,672 m2) 4-story office building and an adjacent 23,750 ft2 (2,206 m2) 5-story parking garage in Queens, New York due to an existing uncontrolled fill layer ranging from 15-20 ft (4.6 - 6.1 m) in thickness beneath the building footprint. The geotechnical engineers for the project initially selected auger cast-in-place (ACIP) piles over driven piles to limit the impact of noise and vibrations on the surrounding neighborhood. Ultimately, drilled displacement piles (DDP) were installed since this method offered a more economical solution that would generate the required pile capacity with shorter drill depths and would also mitigate spoils volume. During installation of test piles by the geotechnical contractor retained for the foundation work, multiple unanticipated soil conditions were encountered that would adversely affect the constructability of the piles. The existing fill contained significantly more natural and manmade obstructions than expected and the underlying glacial soil became too dense to penetrate at shallower depths than anticipated. This paper discusses how these issues were overcome through pre-drilling and the use of detailed instrumented test pile data coupled with in-house engineering capability to proactively re-evaluate minimum pile lengths at any given location and keep the project on track. INTRODUCTION Geotechnical work in the New York City market presents soil conditions that can be highly variable and challenging due to the presence of uncontrolled urban fill placed over the native soils. Construction in this area can therefore pose many unforeseen challenges, even with detailed geotechnical analysis being performed at project sites. A case in point is a construction site in Queens, New York. The proposed site development consisted of construction of a 4-story office building with a footprint of 18,000 ft2 (1672 m2) and a stand-alone 5-level parking garage with a footprint of 23,750 ft2 (2206 m2), together with associated new pavements and utilities. The site is bordered by a mix of commercial buildings and residential properties on all sides. Depth of the uncontrolled nature of the fill extended up to 20 ft (6.1 m) below street grade. Given the significant cost associated with removal and replacement, deep foundations were recommended to bypass the unsuitable soils and support the structures at depth where good bearing material existed.

Jan 1, 2019

By D. T. White

"Metallurgical extraction processes often call for the heating of aqueous slurries. Indirect heat exchangers are generally not feasible for service with high yield stress slurries because of low heat transfer rates. It is more appropriate to heat the slurry by direct contact, typically with steam as the heating medium. Although having a long and successful history, direct-contact heat transfer to aqueous slurries has been used without the support of pilot plant research. This paper provides results of the needed research, the work being done at a scale large enough to enable direct scale up to commercial operations. A pilot plant heater was constructed and tested to develop an understanding of the slurry heating process and to ensure that commercial scale heaters were appropriately sized.INTRODUCTIONPressure Leaching OperationsPressure leaching operations are often used to oxidise sulphide gold ores, or for extraction of nickel and cobalt from laterite ores with sulphuric acid. Where there is sufficient sulphur available, the exothermic pressure oxidation reactions can be self sustaining at temperatures as high as 225 ºC, without having to preheat the feed slurry. At lower sulphur levels, slurry preheating is required. This is typically achieved by utilising the flash steam released from the slurry letdown stages and contacting this directly with cold incoming slurry ahead of the autoclave. The vessels where this slurry-steam contact is made are known as heaters or condensers, with the number of pre-heat stages varying, depending on how much heat is evolved in the oxidation reaction (Mason, 1990).In nickel laterite pressure acid leaching processes, which operate between 245 and 270 ºC, the only significant exothermic reactions are those associated with dilution of sulphuric acid in the leach. As a consequence, slurry preheating with flash steam is always used commercially. In practice the number of flash steam preheating stages required varies from 1 to 3, driven by a number of factors, including other uses for flash steam and the upper temperature limit at which preheated slurry can be pumped. A diagram of a typical pressure acid leach train is shown in Figure 1.For pressure acid leaching operations and at low sulphur levels in pressure oxidation, boiler generated direct steam addition to the autoclave is required to sustain the reaction temperature. For this reason it is imperative that the flash steam – slurry heat transfer is efficient and the slurry temperature approaches that of the flash steam closely."

Jan 1, 2012

By Jim Bruce, Peggy Hagerty Duffy, Mary Ellen Large, Allen Cadden

"Over the past 40 years, Deep Foundations Institute (DFI) has executed its mission “to bring together multi-disciplined individuals and organizations to find common ground and create a shared vision and consensus voice for continual advancement in the deep foundations industry”. Like DFI, micropile technology began a significant growth path in the mid-1980s. This paper highlights how DFI’s mission was executed in the deployment and expansion of micropile technology.INTRODUCTIONMicropiles are small diameter foundation elements constructed using specialty drilling and grouting methods. Micropiles have evolved since their introduction into the North American market in the 1970s from being lightly loaded (less than 30 kips) elements used primarily for remedial applications, to today’s high-capacity, often hybridized foundation systems, for both remedial and new-build projects. Micropiles now occupy a substantial market segment in North America.For 40 years, DFI has aimed to be the forum for discussion of all issues related to deep foundations design and construction. DFI now supports 21 technical committees and working groups on all deep foundations technologies and has expanded to include regional chapters in Europe, India and the Middle East.Several key steps are required for the successful execution of DFI’s mission, including identifying a need, engaging dedicated and knowledgeable people, developing effective vehicles and resources for information sharing, cultivating stakeholder contributions and advancements, stimulating influence/impact on deep foundations market, and expanding approaches to continue progress. Pile drivers in New York City (the original organizers of DFI) positively affected their market using these same steps: they recognized a specific need, gathered the people who could affect change, convened a discussion forum (which is common today, but was innovative at the time), defined tasks to address the issues, and influenced their market by improving means, methods and owner perception of their services. These forward thinking, proactive members created a mechanism for communication among all related parties that would advance the profession by improving safety, quality and value of pile driving construction.Micropile technology has evolved in the United States and around the world for the past four decades. The accumulated efforts of DFI and other, similar organizations such as The International Association of Foundation Drilling (ADSC) have contributed to this evolution. The advancement of the micropile industry – and consequently the micropile market – has been intimately tied to the execution of the mission of DFI."

Jan 1, 2017

By R Berry, J Lett, C L. Harraden

"In the past decade, increased processing capacity combined with precision robotics in high resolution spectrometers has resulted in a new generation of high-speed hyperspectral core logging systems. The application of these multisensor automated platforms provides a key advancement in the characterisation of metal resources. The development of this technology has allowed for comprehensive, drill core-based, mine-scale rock mass characterisation studies. Here we propose a new method for the extraction of parameters that seek to more accurately quantify ground conditions, including quantified rock mass rating (RMR) and the Rock Tunnelling Quality (Q) Index. Data inputs include rock quality designation (RQD), number of joint sets, joint roughness, joint alteration and joint spacing. Geologists and geotechnical engineers have historically collected these inputs by manually logging drill core. With automated core scanning technologies, these parameters can be estimated from the acquired image data and used to objectively calculate RMR and Q-index values for oriented core.Corescan is an automated hyperspectral core scanner that uses a 3D laser profiling system to measure the height of the surface of drill core. This technology allows for rapid core analysis to produce detailed fracture and rock condition data. Through an integrated geometallurgical approach, the proposed methodology will test the accuracy of joint measurement using the height profile Corescan data from oriented drill core. This will be combined with joint roughness and alteration mineralogy measured from the hyperspectral images to calculate the RMR and the Q-index continuously downhole. The values obtained can then be compared to the traditional, manual geotechnical log data. If the precision is sufficient, these techniques can then be applied site-wide to automate the collection and modelling of key ground condition classification indices across an entire deposit. Compared to the laborious manual geotechnical logging procedures that currently form the industry standard, utilisation of core laser profile data and high resolution red-green-blue (RGB) images provide an opportunity to collect large volumes of consistent geotechnical data, which can increase the efficiency and accuracy of deposit scale geotechnical models.CITATION:Harraden, C L, Berry, R and Lett, J, 2016. Proposed Methodology for Utilising Automated Core Logging Technology to Extract Geotechnical Index Parameters, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 119–124 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By A. V. Faiberg

Currently, the interest to conditioning of cyanide-bearing recycled solutions with high-grade of base metals, in particular, copper has significantly grown. This can be explained by two major factors. Firstly, there are strict regulations on cyanides amount in tails and higher cost of detoxification processes. This problem can be easily solved during the ore treatment using the conditioning of solutions and water recycling. Secondly, the presence of other metals minerals which react with cyanide during gold leaching resulting in high cyanide consumption. The presence of copper is a major problem. Many copper minerals react with cyanide with the formation of cyanide complexes-Cu(CN)2-, Cu(CN)32- and Cu(CN)43-. One mole of copper consumes 2-4 moles of free cyanide. Availability of cyanide-soluble copper minerals has deleterious effect on gold leaching (gold recovery, cyanide consumption, tails detoxification, efficiency of gold elution and electrowinning). The precipitation of copper from the solutions improves gold recovery by CIL. The removal and recycling of cyanide allowed the reduction of cyanide addition to the process. The recycling of spent cyanide-bearing solutions based on the removal of copper and the return of cyanide bound in complex compounds for leaching process is an optimal way of solving the problem of gold-bearing copper ores treatment. By using the technology, an adverse impact onto gold recovery process is eliminated and at the same time reducing the cyanide consumption. Today, processes and methods of high-grade copper leaching solutions conditioning before and after gold recovery have been developed, which combine two ways of copper recovery: as a saleable product and cyanide to recover gold and reduce total operating costs. They are Cutech, MNR, SART, Cyanomet, AuGment, Vitrokele, Hannah and Cyanisorb. At the same time, these technologies have not been studied enough and described in literature. Data on parameters and operating conditions as well as introduction is not available. The conditioning technology of recycled solutions developed by IRGIREDMET JSC allows copper to be recovered as high quality concentrate and at the same time free cyanide regeneration in the recycled solution which is amenable to gold leaching. This technology was commercialized at a mine in Kazakhstan in 2008. The removal and recycling of cyanide does not require additional cyanide and is cost-effective. More cost-efficiency is achievable through selling copper concentrates, closed water cycle without the detoxification of effluents and enhanced gold recovery by CIL and cathode quality.

Sep 1, 2012

By D. K. Mynear, J. S. Gardner, S. Mittle, A. A. Campoli

West Virginia, although having adequate solar insolation, has witnessed very little actual solar development to date. The reasons for this lack of development are varied, but the primary obstacles to future development appear to be the absence of state-level policies and regulations promoting growth in the solar industry. West Virginia possesses large tracts of under-utilized land throughout the state created by previous mountaintop mining operations that could theoretically be re-purposed for solar farm development. Accomplishing this task will require not only revisions to the current legislation, but also acceptance by utility companies, landowners, and mining companies. Solar developers will need confidence that they can secure revenue from the electricity and Renewable Energy Certificates (RECs) generated by solar projects. Additionally, solar companies will need assurance they will be protected from any non-related environmental liabilities that could arise in the future. The primary avenue in bringing significant solar development to West Virginia will come through large corporate clients demanding or partnering with utility companies for incorporation of solar options into their energy portfolio to help meet established sustainability goals. This scenario has been witnessed in other states where a large client demands renewable options. Solar development could also represent a means through which mine operators might alleviate some of their reclamation and bonding obligations; where the landowner could supplement income from their underutilized land holdings; and where displaced miners could be repurposed in solar installation/maintenance jobs. Utilizing data from the West Virginia Permit Database, this report identifies several mine sites that hold potential for solar development in the future. INTRODUCTION The diversification of energy sources in the United States (US) has seen major shifts during the past decade resulting from: • A sudden abundance of low-cost natural gas becoming available through advanced horizontal drilling and hydraulic fracturing techniques. • Incentive-driven policies leading to new development in alternative energy. • The emergence of renewable energy sources, proliferated by state and federal level incentives and falling capital costs. Coal was once the primary low-cost fuel source for the generation of electricity in the US for most of the last century, providing approximately 50 percent of the total production capacity. However, within the past decade lower-cost natural gas has overtaken coal as the primary source of fuel used in electricity generation, and renewable sources have steadily grown to account for approximately 10 percent of the overall mix.

Jan 1, 2019

By N Power, A D. Costar

There has been significant growth in mining and energy exploration in South Australia, which has identified new major potential opportunities. This sector generates significant economic value to the state and their support remains a priority for the state government. The delivery of this economic and associated community value to the state is dependent on the mining and energy sector being able to access reliable water supplies.The vast majority of priority areas for the mining and energy sectors are located in areas that have traditionally been of low priority from a water-use perspective and hence, data and knowledge levels are generally low.Recent studies have identified a potential increase in demand for water in the mining and energy sector for potential developments from approximately 40 GL to over 170 GL over the next ten years. The studies found that water and water infrastructure is the second highest proportion of planned infrastructure capital investment by resource companies. The South Australian GovernmentÆs Plan for Accelerating Exploration (PACE) initiative (PACE 2020), also identifies addressing the issues of location, use and management of South AustraliaÆs water resources as a key priority for the growth of the mining and energy sector.The Department of Environment, Water and Natural Resources (DEWNR) has developed the facilitating long-term outback water solution (FLOWS) initiative. DEWNR is currently undertaking a suite of programs to provide groundwater information at the regional scale to better target water supply options for mining and energy developments and community water supplies.The Goyder Institute for Water Research has leveraged significant research investment of $3 M to develop methodologies to interpret airborne geophysics to map groundwater sources.The FLOWS Initiative will provide key content for the PACE Water Program and will also assist in the development of water supplies for remote far north communities by identifying alternate groundwater sources to improve water supply security.This paper will discuss how developing an appropriate science and knowledge base will encourage and secure development where appropriate, enable prudent decision-making and policies regarding water allocation, accounting and licensing, whilst ensuring the protection of environmental assets.CITATION:Power, N and Costar, A D, 2013. Finding long-term outback water solutions, in Proceedings Water in Mining 2013 , pp 191-196 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013

By K. Sasaki, W. Astuti, N. Okibe, T. Hirajima

"The kinetics of leaching of a saprolitic ore from Indonesia by citric acid solution under atmospheric pressure was investigated. An examination of the effects of leaching temperature, citric acid concentration, pulp density and ore particle size on the dissolution rate of nickel found that they all had significant influence on the rate. The highest nickel recovery (95.6 percent) was achieved under the leaching conditions of ore particle size of 212-355 microns, citric acid concentration of 1 M, leaching time of 15 days, pulp density of 20 weight/volume percent, leaching temperature of 40°C and shaker speed of 200 rpm. The shrinking core model was found to be appropriate for describing the leaching kinetics of this ore in citric acid solutions at atmospheric pressure. The experimental data were well interpreted by this model with rate of reaction controlled by diffusion through the solid product layer. Using the Arrhenius expression, the apparent activation energy for nickel dissolution was evaluated as 12.38 kJ/mol. Finally, on the basis of the shrinking core model, a proposed empirical kinetic model for the leaching of nickel from this Indonesian saprolitic ore was expressed as a mathematical model, which was verified as consistent with the observed experimental results.IntroductionIndonesia has some of the world’s largest nickel laterite reserves and was the largest producer of nickel – in the form of nickel lateritic ores – in the world in 2013 (Merchant Research and Consulting Ltd, 2014). However, only high-grade saprolites are processed in Indonesia using pyrometallurgical methods to produce ferronickel and nickel matte. Lower-grade saprolites and limonites are removed, becoming waste or overburden in mining site areas. Hydrometallurgical methods, involving either chemical leaching or bioleaching, are now seen as the most important technologies for treating nickel laterites in the future because of their advantage of not only extracting nickel and iron but also other valuable elements. In addition, hydrometallurgical methods consume less energy and have lower capital and operational costs. Although they are recognized to be more suited to limonites, some researchers have studied their use in the extraction of nickel and other metals from saprolites (Guo et al., 2009; Lu et al., 2013). Hydrometallurgical processes for the extraction of metals, especially nickel, promise to be meaningful alternatives to pyrometallurgical processes to primarily treat low-grade saprolites for which pyrometallurgical processing is not favorable"

Jan 1, 2015

By Alexander Smith

"The Silver Standard mine is 6 miles by road northwest of New Hazelton, B.C., a small town on the northern line of the Canadian National Railways some l 75 miles northeast of Prince Rupert. The deposits lie on the western slope of Glen Mountain (elevation 2,100 feet), with the main adit, mill, and campsite at 1,300 feet. The deposits were found in 1910, shortly after the area had been swept by forest fire and during a period of prospecting activity spurred by the construction of the railway. Crude ore only was shipped until 1918, when a 50-ton gravity mill was built which operated until 1922. Gross value of production of this period, at present metal prices, was about $1,000,000.In 1947 the present company was formed and a 50-ton flotation mill installed. Production from 1948 to 1955 has been in excess of $10,000,000, and net smelter returns about two-thirds of this amount. More than 60 per cent of the production and 80 per cent of the profit have come from one vein, No. 6. On the 1,300-foot level this vein had an ore section 375 feet long and 2.5 feet wide, averaging 0.18 ounces gold, 85 ounces silver, 10 per cent lead, and 16 per cent zinc.The mine workings follow a simple pattern. A series of parallel veins, striking northeast and dipping southeast, are numbered from 0 to 12, starting at the northwest. They lie within a zone trending south 70 degrees east, and the distance between Nos. 0 and 12 veins is about one mile. Recently several cross-veins, dipping northeast, have been found between Nos. 8 and 12. They are apparently of the same type as the others, though they may not have the same structural controls. They could be an important new source of ore.The mine has been developed principally by crosscut adits at the 1,500- and 1,300-foot levels and a 510-foot shaft with levels at I, 150, 1,000, ·and 850 feet. Drifts and crosscuts total 17,000 feet, chiefly on Nos. I, 4, 6, 7, and 8 veins. The drifts are stoped by shrinkage, top shrinkage rill, cut-and-fill with resuing, or open stope methods. The mill produces a lead-silver-gold-copper concentrate and a zinc concentrate, with indicated recovery of more than 96 per cent (4)."

Jan 1, 1949

By Juan M. Pestana, Jeremy M. Gasser, Cuneyt Gokmen, Paul J. Sabatini, William Tanner, Daniel J. Woeste

An access pathway and working platform were designed and constructed for equipment access for a Deep Soil Mixing (DSM) pilot study over a coal combustion residual (CCR) surface impoundment (SI). The DSM pilot study was conducted to evaluate slurry mix designs and construction techniques for installing DSM columns up to 95 feet deep. Two-dimensional (2-D) limit equilibrium and 2-D finite element analyses were used to evaluate multiple failure mechanisms including: (i) bearing capacity, (ii) punching shear of mixed ground and underlying CCR, (iii) effect of fluidized DSM columns on working platform stability, and (iv) liquefaction. The analysis results were used to design ground improvement required to increase bearing capacity and stability of the CCR under the proposed equipment access route. A long-reach excavator was used to perform shallow bucket mixing and walk onto the CCR SI atop previously mixed cells following a minimum cure time and acceptance of quality control test results. Prior to mobilizing the DSM rig, a static load test was conducted to evaluate performance of the working platform. Both the access pathway and working platform demonstrated acceptable performance under the design loads during the DSM pilot study. This case study emphasizes the economic and safety benefits that can be realized by appropriately designing critical temporary work items such as access pathways and working platforms in difficult ground conditions. INTRODUCTION A Deep Soil Mixing (DSM) pilot study was conducted at a coal combustion residual (CCR) surface impoundment (SI) to evaluate slurry mix designs and construction techniques for closure design of the SI (Site). Sluicing of CCR at the facility ceased and closure will be initiated based on requirements in the final United States Environmental Protection Agency (USEPA) Rule for Disposal of Coal Combustion Residuals from Electric Utilities, 40 CFR 257, effective October 19, 2015. The proposed closure approach involves constructing a DSM containment structure (DSM Wall) to separate the SI into two areas: (i) a closure by removal area; and (ii) a consolidate and cap-in-place area. The proposed DSM Wall would retain the CCR within the consolidated closure footprint and provide a barrier between the two areas of the SI. The predominant CCR in the SI where the pilot study was conducted were fly ash and bottom ash. CCR materials in surface impoundments are generally soft and saturated as a result of being sluiced into place and can present stability and safety challenges when performing earthwork activities.

Jan 1, 2019

By Ana Pereira, Naomi Norris, Donald Bruggers

The city of Christchurch, New Zealand is predominantly founded on alluvial sediments consisting of interbedded layers of loose to medium dense sand, soft to stiff silt and clay mixtures, and pockets of organics. These soil deposits have high liquefaction potential. Following the 2010/2011 Canterbury Earthquake Sequence several ground improvement trials were undertaken within Christchurch to understand the effectiveness of different types of ground improvement in these silty sand geological conditions. This paper presents a discussion of a stone column ground improvement trial undertaken at a Christchurch site with high fines content soils. Stone columns were installed using two types of installation methods and a range of Area Replacement Ratios (ARR) to assess the effectiveness of these ground improvement methods in high fines content soils as well as the influence on the type of installation method. Pre- and post-column installation CPTs, seismic Dilatometer Tests (sDMTs), cross-hole shear wave velocity tests, and plate load tests have been undertaken to assess the effectiveness of the ground improvement. Results of the testing are presented in this paper. INTRODUCTION This paper presents the results of a stone column ground improvement trial undertaken in Christchurch, New Zealand (Fig.1). In 2010 and 2011, four large earthquakes (greater than magnitude 5.9) and thousands of smaller aftershocks occurred in the greater Christchurch region. These events are referred to as the Canterbury Earthquake Sequence (CES). Liquefaction occurred across large portions of the city during the stronger earthquakes, particularly the February 2011 event. Following the CES a large amount of data was collected across the city including the location and volume of sand boils, and the location and magnitude of ground cracks. Additionally, data from thousands of ground investigations have been uploaded into a public database. As a result, there is clear evidence that silt and silty sands liquefy in addition clean sands. The CES and resulting liquefaction motivated a series of studies and trials from different organisations aiming to better understand the available technologies for liquefaction mitigation. The subject of this paper is a ground improvement trial undertaken by a local contractor specialising in deep foundations and ground improvement. They were interested in understanding the effectiveness of stone column ground improvement in high fines content (silty) soils using two different installation techniques, vibratory and non-vibratory. Different arrays and Area Replacement Ratios (ARRs) were used for each of the two methods of columns installation.

Jan 1, 2019

By B. Hohenstein, B. McBain, B. de Jong

"The automated fire assay system (Fast In-line Fire Assay or FIFA) has not found acceptance in the Au mining industry as the lower measurable limit of 0.20 ppm did not allow Au tailings to be measured with confidence. The development of arrested cupellation has overcome this hurdle which was a limiting factor in the FIFA 1 process. In the new automated fire assay process, automated sample preparation, fluxing, fusion and separation of a Pb button are essentially similar to the FIFA 1 process, albeit with some improvements. However, the game-changer is the development and incorporation of arrested cupellation into the automated system, now called FIFA 2. The purpose of arrested cupellation is to reduce the 50 g Pb button to a 5 g Pb button by partial cupellation in a specially developed arrested cupellation system thereby concentrating the Au in the Pb by a factor of 10 and in so doing moving them into higher concentration ranges in the mini-button where they can be read on the spark spectrometer. Results show that concentrations down to 0.02 ppm Au in geological materials can now be determined using arrested cupellation in the FIFA 2 process, an order of magnitude improvement over FIFA 1.INTRODUCTION Traditional fire assay for Au has remained virtually unchanged for 3000 years. It has survived for so long because it is accurate, has relatively low detection limits and is relatively inexpensive. However, it is labour intensive, has a long turn-around time (typically at least 7 hours), is environmentally unfriendly and exposes assay operators to potentially unsafe conditions (toxic fumes, toxic dust and extreme heat from furnaces). The NiS collection method is not as effective for the assay of Au as it is for the PGEs. A rapid, accurate, cost-effective method for the determination of Au and the Platinum Group Elements (PGEs) in geological materials would be a tremendous benefit to mining companies. Many of these objectives have been met by the FIFA 1 (Fast In-line Fire Assay) developed some 15 years ago in which automated methods have replaced the manual procedures which are part and parcel of conventional fire assay. However, concentrations below 0.2 ppm have been very difficult to achieve with sufficient reliability."

Jan 1, 2017

By N. S. Dalal, B. Jafari, F. H. Y. Green, M. M. Suryan, V. Vallyathan

"Freshly ground and aged anthracite and bituminous coal samples were investigated by electron spin resonance (ESR) spectroscopy to detect the presence, concentration and reactivity of free radicals. Freshly ground anthracite coal produced greater concentration of free radicals than the bituminous coal, and the radical reactivity was also greater for the anthracite. The reactivity of the newly produced free radicals in the anthracite dust correlated with the dust's toxicity. Furthermore similar coal-based free radicals were detected in the lung tissue of autopsied coal miners, suggestive of persistent reactivity by the embedded coal dust leading to the progressive disease process. Results of the studies on the severity of coal workers' pneumoconiosis (CWP) and free radical concentration m lung tissue support this hypothesis.INTRODUCTIONCOAL WORKERS' PNEUMOCONIOSIS (CWP) has been an important topic of concern to miners, mining engineers, epidemiologists and medical researchers for decades. It is well known that the prevalence and severity of CWP differ markedly between different regions and mines despite comparable exposures to respirable dust (REISNER and RoBOCK, 1977; HURLEY et al., 1979). These variations in pathogenicity of coal mine dusts can only partially be explained by differences in the mineral composition and by rank of coal (CHRISTIAN and NELSON, 1978; CHRISTIAN et al., 1979; HATCH et al., 1980). Cytotoxity studies on mammalian cells do not correspond well with the human disease pattern (CHRISTIAN and NELSON, 1978; CHRISTIAN et al., 1979; HATCH et al.,1980; VALL YA THAN et al., 1988). For example, while epidemiological studies of coal miners (REISNER and ROBECK, 1977; HURLEY et al., 1979) indicate that the prevalence of CWP correlates roughly with the rank of coal, such correlation has not yet been established in biological studies, despite considerable effort (CHRISTIAN and NELSON, 1978; CHRISTIAN et al., 1979; HATCH et al., 1980). In order to help resolve this apparent paradox we have undertaken a systematic study to evaluate whether any correlation exists between the concentration of free radicals present in fresh or aged coal dusts from two well-characterized U.S. coals. This study was also prompted in part by observations reported in the literature that organic free radicals can be formed on the surface of freshly fractured coals (LEBEDEV et al., 1978; DULIBA and CLARKSON, 1984). In particular, ARTEMOV and REZNIK (1980) noted that the decay lifetimes and, hence, the reactivity of the organic free radicals formed on crushing Russian coals, .depended"

Jan 1, 1989

By Jerry R. Riding

Metallurgical process methods have seen dramatic improvement over the past fifty years. As these improvements have come about, more and more emphasis has been placed on obtaining accurate and rapid analysis of the metallurgical processes. Well-defined conventional laboratory analysis procedures which have proven to be reliable were developed early in the mineral industry's history; however, these conventional procedures, which have not changed appreciably in fifty years, have the serious drawback that they are too slow to be of appreciable value in automatic control of the processes. For example, the assay results normally become available to a mill operator from eight to twenty-four hours after a sample is taken. Since the desired mineral separation can only be made while the minerals are in the flotation circuit, conventional assay results provide information similar to postmortem reports. Consequently, using conventional procedures, the mill is operated with information from an earlier period of time, which may not reflect current conditions. In recent years there has been a steady increase in the volume of required samples. At the same time, labor, material, and overhead costs have continued to rise causing the cost per assay to reach an alarming level. This rising cost per assay, plus the increasing demand for rapid analysis necessary for control, has caused the mining and metal processing industries to look toward other techniques to solve these problems As a result, X-ray fluorescence which can provide on-stream analysis necessary for control, as well as perform numerous laboratory assays at lower cost and at a much greater speed than conventional methods, has gained wide-spread attention. In addition, multichannel X-ray fluorescent instruments are now available which have been perfected to the point where the analysis of the most important chemical constituents is available within one minute after a sample is presented to the X-ray analyzer. Because of these obvious advantages, extensive use is being made today of X-ray analysis in the mining industry to analyze slags, ores, and mineral content of rocks. The results are used to make quick decisions for both mining and beneficiation of metals. For example, X-ray systems which provide rapid on-stream analysis of the slurries at desired points Fn metallurgical processes have recently been developed. The successful application of these systems has moved the milling process a step closer to fully automatic control.

Jan 1, 1969