Search Documents

1. Mine drainage constitutes surface or ground water which flows from mines or mine sites and is usually characterized by concentrations of acidity or alkalinity. 2. The regional geology controlling the ground water flow pattern in conjunction with the life cycle mining plan can serve as a basis for making decisions about quality of water that can be expected to be encountered. 3. In regard to the prevention and control of acid water formation in underground coal mines, much is left undone in research and education: (A) Very little literature is available on this specific subject although much has been written on water management in underground mines. (B) Little or nothing is contained in the text books and curricula used in mining departments at colleges and universities with the result that educational offerings may be seriously deficient in these areas. 4. Prohibiting water entry into underground coal mines is the best method of preventing water pollution. Since this is not possible as mining operations are extended, preventing water or oxygen from contacting acid producing material may offer the next best alternative. 5. More emphasis is needed during the mine planning stage on steps to prevent water pollution. Such life cycle considerations as type of mining, sequence of development and spatial configuration as well as the elements of the drainage network and final network organization and extent must be considered.

Jan 1, 1970

By J. J. Dowd

1. The Pittsburgh bed is the most important bed in Ohio County, and virtually the entire production of coal in the county comes from this bed. 2. Known measured and indicated reserves in all beds, based on a minimum thickness of 14 inches and 1,800 tons per acre-foot of-coal in place, are estimated at 365 million short tons as of January 1, 1954. Of this total, 356 million short tons is in beds 28 inches and more thick. Areas in each bed were omitted from the estimate because available data relative to the bed characteristics are too meager to make an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.

Jan 1, 1955

By Thomas Pallua, William C. Gates

"Two major railroad companies have identified several segments along the railroad corridor betweenTehachapi and Bakersfield, Kern County in California that require construction of a second track to improve operations in this area. The total project proposes an upgrade of five segments along the Tehachapi-Bakersfield route. The authors focused on two segments: Walong to Marcel and Cliff Siding Extension. The second track project comprised design of a through-cut adjacent to an existing tunnel and up to 120-feet-high (36m) side-hill cuts (both in granitic rock). The authors characterized the geologic ground conditions and ground behavior, including rock mass quality and strength using a combination of rock core drilling and rock slope mapping. The rock mass is generally characterized as granitic tonalite with strong core stones surrounded by a matrix of decomposed granite (DG)."

Jan 1, 2017

By F. W. Metzger

INTRODUCTION Coal quality control in mining and mine planning has always been important and has become even more essential in recent years due to environmental considerations. The primary consumers of the sub-bituminous coals found in the Powder River Basin are electric utilities that require low sulfur coals to meet government air quality regulations. Electric generating plants are designed to burn coal of a specific quality, and the supplier of that coal must be able to guarantee shipments within specified quality tolerances. Over the past several years, Exxon Coal USA and, more recently, The Carter Mining Company, a division of Exxon Coal USA, have established an evaluation and development program to accurately define the geology and quality of their coal properties. This requires an adequate drill hole density so that detailed correlations of the coal seam and the lithologic units, or benches, within the coal seam can be made. These units are recognizable in the core and also on geophysical logs. Like any systematic approach, geologic modeling has been refined and improved through new technologies. Today, coal seam properties are mapped using computer applications. Rapid access and manipulation of these data allow for optimization of mining efforts. This presentation will demonstrate how a detailed mapping program can be important in both pre-mine development and in-pit quality control.

Jan 1, 1983

By D. F. Coates

Slope problems arise on mining properties from cuts for roads and railroads and from open pits. When it is 'realized that 1,000,000 extra tons of waste may have to be mined as a result of an average slope being reduced by 1 ° it is easy to appreciate that the slope problems connected with open pits are of far greater importance than the others. The type of slope failure that can occur can be classified in different ways. The most useful classification would be one that separates the causes in such a way as to provide a basis for studies to deal with problems of prevention and control. Using this criterion the types of slope failures are classified into four groups. Having classified the problems in this way an understanding can be gained of the various mechanisms involved in failure ..

Jan 1, 1961

By J. J. Dowd

1. The Pittsburgh bed is the most important bed in Brooke County and virtually the entire production of coal in the county comes from this bed. 2. Known measured and indicated reserves in all beds, based on a minimum thickness of 14 inches and 1,800 tons per acre-foot of coal in place, are estimated at 191 million short tons as of January 1, 1954. Of this total, 190 million short tons are in beds 28 inches and more thick. Areas in each bed were omitted from the estimate because available data relative to the bed characteristics are too meager to make an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.

Jan 1, 1955

By Z. Liang, Z. Q. Liu, X. F. Li, H. L. Zhang

"Dynamic characteristics of frozen soil is important for the safe, effective and rapid construction in cold regions and artificially frozen engineering. In this paper, dynamic characteristics of frozen clay with various low temperature and different strain rate were studied by using Split Hopkinson Pressure Bar (SHPB) test and numerical simulation test. Variation of dynamical parameters and dynamic stress-strain curves of frozen clay were obtained and analyzed. The results of these test show that: Frozen clay exhibits temperature effect and strain rate effect that the failure type tends from plastic failure to brittle failure with the increase of strain rate or decrease of temperature; Under impact loading, frozen clay exhibits three typical dynamic stress-strain curves as strain rate increases, and the maximum strain of frozen clay only linear increases with strain rate.INTRODUCTIONArtificial freezing technology has been widely used in the construction of underground engineering, such as the coal mine shaft, the deep foundation pit, the urban metro and subsea tunnel, etc. Research on dynamic mechanical behavior of artificial frozen soil will provide supports for these artificially frozen engineering (Xu et al. 1998; Ma 2009). However, the dynamic mechanical research on frozen soil is mainly carried out at low frequencies or small amplitudes of the waves, behavior of frozen soil under impact loads or high strain rate loads has not been made clear."

Jan 1, 2015

By Mills KW

Coal mine pillar design formulae available to mine planners are typically based on relationships determined for specific site conditions. Application of these methods is difficult when other factors, relating to mining or geological conditions, not specifically addressed in these relationships are encountered. A review of pillar design methods, coal strength properties and relevant field monitoring of pillar behaviour has shown pillar strength and deformational characteristics are extremely sensitive to in situ behaviour of the rock and other material components that make up the coal pillar system. A method has been developed that has been found to provide excellent correlation between existing field data using the strength and deformational characteristics of materials determined in selected laboratory tests. This method is based on definition of the loading conditions, accurate modelling of the strength, confining conditions and deformation occuring in the roof, floor and coal seam and definition of the in situ strength of coal based on underground monitoring of appropriately sized coal pillar. The design method is considered to provide an accurate and rigorous pillar design method that will give mine planners a more rational mine design capability which is based on the mine geometry and geological setting of the operation. It is envisaged that availability of such a method will allow significant optimisation of pillar layouts and more closely define the geological and mining issues that relate to pillar design optimisation.

Jan 1, 1992

By G. W. Phelps

The field of industrial minerals is concerned with both sieve size and distribution of sub-sieve particles. A great deal of work has been reported on the techniques designed to provide information of this work. The term sub-sieve is here considered to include particular material that will pass a 325-mesh testing sieve. Plant men require rapid, precise and simple testing techniques that are, if possible, inexpensive with respect to equipment and manpower. A number of particle-size procedures have been developed, based on the Stokes equation for streamline movement of a particle of diam D, moving at velocity V through a liquid of viscosity n. 1 Particles are considered to be rigid, smooth spheres, completely dispersed at low concentration and moving at low velocity through the suspending medium with no slippage between particle and liquid. In particle size determinations the particle moves either from natural gravitational forces or those provided by centrifugal means. The diagram of Fig. 1 shows a spherical particle of density S and diam D moving downward at velocity L/T (or V) through a liquid of density So and viscosity n. The forces of gravity G (natural) or Gc (centrifugal) cause the particle to move through the liquid, thereby creating a viscous drag F or Fc. Within the streamline flow

Jan 1, 1967

By J. Fastle, M. Weinstock

The block cave mining method utilized by PT Freeport Indonesia (PTFI) generates fines and allows the inflow of water. Both constituents have contributed to unfavorable characteristics: an increase in ore material plasticity and fluidity. Unfavorable material needs to be monitored and managed as it passes from intermediate ore stockpiles through feeders and then to milling operations. We describe an implementation of several Video Data Analytics (VDA) algorithms on smart cameras to quantify the potential fluidity and plasticity by measuring the apparent velocity and agglomeration of material flowing through ore feeders. This approach to VDA on smart cameras is a cost effective, self-contained, solution to identify these unfavorable characteristics. The solution allows the operators to manage the related operational risks, maintain safe production and govern feeder rates when material is unfavorable, which is expected as PTFI proceeds deeper into the underground orebody

Mar 2, 2022

By R. I. Rodriguez

Since the 1973 energy crisis, high fuel oil costs have been eroding the economics of the Nicaro and Punta Gorda Plants that employ the Caron Process for laterites processing. Since 1995, Cuban crude oil production has growth dramatically, with progressive utilization in power generation, cement and nickel plants. This paper shows how Nicaro and Punta Gorda plants have been able to shift from expensive Bunker C Fuel Oil to heavy but cheaper Cuban Crude Oil of high Sulfur content and achieve a significant reduction in operating cost. Problems related to the high sulfur content of the Cuban crude oil have demanded extensive investigations of the process chemistry and novelty solutions are proposed, with corresponding changes in process conditions. Innovative options are shown that will allow further cost reductions in the future. Keywords: Cuban Crude Oil, Sulfur, Ammonia.

Jan 1, 2004

By Ehsan Khajeh

In this study, the permeabilities of Al-15.5wt%Cu and Al-19.5wt%Cu have been determined by solving the full Navier-Stokes equations on 3D geometries of interdendritic channels obtained by X-ray microtomography (XMT). The samples for XMT were sectioned from different positions in directionally solidified cylinders in order to obtain a variety of microstructures for each composition. The flow has been solved using a 2nd-order accurate Finite Volume Method (FVM) approach. The effect of employing uniform or unstructured mesh on the calculated permeability has been studied. The Marching-cube triangulation method was necessary to extract accurate surfaces for unstructured volume meshing. Calculated values of permeability for this range of solid fractions show partial agreement with previous experiments. Observed deviations are attributed to the difficulties of experimental permeability measurements.

Jan 1, 2009

By Michael G. Li

Prediction of acid rock drainage (ARD) for low-sulphide, low-neutralisation potential (LSLNP) mine wastes is methodologically different from that for normal sulphidic mining wastes. In this paper. LSLNP wastes are conveniently defined as those with S2 < 1% and ABA-NP2 < 20 kg CaCO3 eq/t. The distinctiveness of ARD prediction for LSLNP materials originates from their frequently low oxidation rates and is mainly attributable to two reasons. First, the utilisation efficiency of available carbonate neutralisation potential (CNP2) rapidly deteriorates when the sulphide oxidation rate per unit mass of waste drops below a certain level. Reducing the flushing rate of a waste has the same effect as increasing the oxidation rate. Second, silicate neutralisation becomes increasingly important as oxidation rates diminish, and can no longer be ignored in LSLNP materials as it often is for normal sulphidic mine wastes. In this paper, the effects of oxidation rate, pore gas CO2 partial pressure, and flushing rate on ARD prediction for LSLNP materials are theoretically demonstrated with the help of modelling using the computer program MINTEQA2. A new methodology for ARD prediction for LSLNP materials is presented in terms of a prediction procedure. Finally, a case study is given to validate some of theoretical aspects discussed and to illustrate the use of the newly proposed ARD prediction procedure.

Jan 1, 2000

By Winton J. Gale

Coal mine pillar design formulae available to mine planners are typically based on relationships determined for specific site conditions. Application of these methods is difficult when other factors, relating to mining or geological conditions, not specifically addressed in these relationships are encountered. A review of pillar design methods, coal strength properties and relevant field monitoring of pillar behaviour has shown pillar strength and deformational characteristics are extremely sensitive to in situ behaviour of the rock and other material components that make up the coal pillar system. A method has been developed that has been found to provide excellent correlation between existing field data using the strength and deformational characteristics of materials determined in selected laboratory tests. This method is based on definition of the leading conditions, accurate modelling of the strength, confining conditions and deformation occuring in the roof, floor and coal seam and definition of the in situ strength of coal based on underground monitoring of appropriately sized coal pillar. The design method is considered to provide an accurate and rigorous pillar design method that will give mine planners a more rational mine design capability which is based on the mine geometry and geological setting of the operation. It is envisaged that availability of such a method will allow significant optimisation of pillar layouts and more closely define the geological and mining issues that relate to pillar design optimisation.

Jan 1, 1992

By E. Emami, J. Valencia, J. Sattarvand

The knowledge of the final location of a drillhole is critical in obtaining the expected blasting results. This paper proposes a new methodology to control the drilling accuracy in open-pit mines using aerial images and machine learning. Specifically, it investigates how support vector machines (SVM) and convolutional neural networks (CNN) are useful for automatically detecting blastholes over drone images captured in blasting patterns. Several datasets were obtained from different mines in Nevada (USA) and were used to train and test models. We then processed those images to create orthomosaic and digital elevation representations of the patterns. Thousands of patches were then extracted and augmented to develop SVM and CNN models. The results demonstrate that machine learning is useful for drillhole detection and, in this way, to control the drilling accuracy and use the explosive energy more efficiently.

Sep 1, 2021

By Joseph D. McClung, L. G. Austin

INTRODUCTION Run-of-mine (ROM) coal generally falls into two major groups, that from underground mining (continuous mining machines) and that from strip mining. Continuous miners produce a finer product and strip mining a coarser product that is crushed to produce the desired size. Further size reduction depends on the proposed use or uses for the coal. For example, for pulverized coal power plants as a rough general rule, the coal is ground or pulverized to 80% less than 200 mesh (0.075 mrn) before it is blown into the boiler furnace as a coal-air suspension. For solvent-refined coal processes, the desired size is about <30 mesh ( <0.60 mm) ; in fluidized bed uses, the coal is typically < in. ( < 1.6 mm); for Lurgi pressure gasifiers, the desired size is 1-2 1/2 in. (25-63 mm). Coal preparation plants typically work with a coarse size fraction of 6x1 1/4 in. (15Ox32mm). It seems probable that the next decades will see much wider application of coal cleaning before use and that the stages of crushing and pulverization from ROM coal to end use will be integrated with coal cleaning processes. Since different cleaning processes work better with different ranges of coal size and the degree of cleaning possible is inti-

Jan 1, 1979

By Seth C. Schaefer

The Bureau of Mines investigated thermodynamic properties of Mn304 (manganomanganic oxide) and Mn203 (manganese sesquioxide). The standard Gibbs energies of formation (?Gf°) of Mn304 and Mn203 from their lower oxides were determined with high-temperature galvanic cells using stabilized Zr02 (zirconia) as the electrolyte. Potential measurements were obtained for the cell Pt, MnO, Mn304//Zr0 2//02(g, 0.0112 atm), Pt, with the overall cell reaction 6Mn0(c) + 02(g, 0.0112 atm) = 2Mn304(c), where- 02 refers to indicated partial pressure of oxygen at the reference electrode. Similar measurements were obtained for the cell Pt, Mn304, Mn203//ZrO2//02(g, 0.0115 atm), Pt, with the overall cell reaction 4Mn304(c) + 02(g, 0.0115 atm) = 6Mn203(c). Equilibrium oxygen pressures for the Mn0-Mn304-02 and Mn304-Mn203-02 systems were measured and may be expressed for the respective systems as [23,400 109 P02 T + 11.91 (764.9 - 1,208.6 K) and log p02 = - 11,957 + 9.66 T (968.6 - 1,208.2 K),] where pressure (p02) is in atmospheres and temperature (T) is in kelvins. Standard thermodynamic properties of Mn304 and Mn203 were derived from these measurements and auxiliary thermodynamic data from the literature.

Jan 1, 1982

To pinpoint dust sources and to improve dust control on longwalls. Approach Use short-term gravimetric sampling to determine the severity of various dust sources, and to evaluate dust control techniques used in longwall mining. Short-term gravimetric sampling can be used to isolate dust levels produced by various dust sources. How It Works Traditionally, gravimetric samples have been collected over an 8-hour shift, yielding time-weighted, average dust concentrations. This method gives a good indication of the full-shift respirable dust exposure of underground workers, but is less than satisfactory for identifying dust sources, determining their severity, or for evaluating the effectiveness of dust control techniques. Short-term gravimetric sampling uses equipment available to all mine operators. Two individuals composing the survey team each collect multiple (three to four) gravimetric samples during selected segments of the mining cycle. Multiple samples are necessary to insure accuracy, and to obtain a valid average measurement of the respirable dust concentration when sampling for short periods of time (typically 20 to 30 minutes). The gravimetric instruments may be carried in a sampling package or in a "sampling vest." A fishing vest with four large pockets can be used for this purpose. The sampling pumps are carried in pockets and the sampling head assemblies arc hung across the front of the vest.

Jan 1, 1982

By C. A. Summers

The U.S. Bureau of Mines applied process mineralogy to investigate a lead and zinc deposit located near Story Creek, Colville Mining District, Alaska. Mineralization is hosted by the Kayak Shale in veins, veinlets, and breccia. Sphalerite and galena, with supergene anglesite, occur in symmetrical quartz veins and between breccia clasts. The study sample analyzed 2.11 percent Pb, 5.37 percent Zn, 0.014 percent Cu, and 1.2 oz/ton Ag. Analyses of crushed products showed that 33 percent of the sample weight, and more than 50 percent of the Pb and 65 percent of the Zn, are in the minus 850 um fraction. Liberated grains of sphalerite and galena were found in crushed products finer than 300 um. Beneficiation tests indicate the material is amenable to processing by traditional gravity and flotation techniques.

Jan 1, 1991

By S. Torizuka, I. Mizushima. Kawasakitohri, A. Ohmori, K. Nagai

Strain (work)-hardening in tensile tests were examined for low carbon steels with various ferrite grain sizes ranged from 0.4µm to 16µm. The steels had microstructures composed of ferrite grains and dispersed cementite particles. They were fabricated through warm caliber rolling with an accumulative area reduction of 93%. Strain-hardening rate at a given strain increased with an increase in volume fraction of cementite particles. The balance of yield strength and uniform elongation for ultrafine-grained structures could be improved by the dispersion of cementite particles. Effects of the cementite dispersion and the ferrite grain size on the strain-hardening rate can be roughly explained by the work-hardening model with GN-dislocation density. Strain-hardening design using dispersed cementites was proved to be effective in controlling ductility of the ultrafine-grained steels.

Jan 1, 2004