Search Documents

By C. A. Young

Previous experimental results have shown that an increase in temperature and/or oxygen concentration leads to an increase in the hydrophobicity of fluorite (CaF2) with adsorbed oleate. Subsequently, ex-situ Fourier transform infrared (FT-IR) transmission studies suggested that this increase in hydrophobicity was the result of double-bond reactions between adjacent oleate species adsorbed at the fluorite surface. Now an in-situ FT-IR study on single crystals of fluorite has been used to monitor this phenomenon using internal reflection spectroscopy (IRS) with the crystals serving as reactive internal reflection elements. The double-bond reaction has been correlated with in-situ adsorption density measurements. These results demonstrate that only the first chemisorbed oleate layer undergoes the double-bond reaction at an appreciable rate. However, multilayers of precipitated calcium oleate in the case of fluorite appear to react minimally even for oxygen saturated solutions at elevated temperatures.

Jan 1, 1991

By H. M. Wilten

THIS article presets a view of a problem encountered in petroleum refining in the deterioration of equipment used in condensation of vapors and cooling of liquids. Discussion is limited to the problems of shell- and tube-type exchangers and condensers. In this service shell- and .tube-type equipment is gradually displacing other types and, for this reason, its economic importance ill oil-refining practice is also increasing. Considering oil - refinery practice during the last two decades one can readily see many important improvements in the apparatus used. Briefly, the present equipment is safer, more efficient, and Ignore economical. Improvement in apparatus used for the condensation of distillates has, in my opinion, been less than that in other essential distilling apparatus. So it is hoped that this discussion will stimulate research among the producers as well as among the consumers of this equipment with a view to ameliorating this condition.

Jan 1, 1937

By Kirk Carlton

The Athabasca tar sands of Alberta are an increasingly important source of crude oil for the North American continent. Published figures indicate estimates of recoverable resources in the tar sands at some 300 billion barrels of synthetic crude of which some 86 billion barrels can be recovered by surface mining techniques. At the present time, two commercial plants are in operation, Great Canadian Oil Sands Limited and Syncrude Canada Ltd. Their present combined capacity is approximately 150,000 barrels per day. Some of the factors which will make this oil expensive will be noted here. The location of the present producing plants is 500 kilometres north of Edmonton at an elevation of approximately 320 metres. Recorded temperatures range from +38 to -55 degrees Celsius. Wind velocities are not high but the chill factor with even a slight breeze and minus 40 degrees is very uncomfortable.

Jan 1, 1979

By Aiming Z, Shenyi S, Xialei W

Zhangmatun Iron Mine is situated in the suburbs of Jinan city. Shandong, China. Because of surface environmental constraints, no suitable site can he selected to dispose of mill waste. The full mill tailings must be disposed of underground. This paper deals with the work conducted at Zhangmatun mine to develop a total tailings backfill system, taking advantage of a double- shaft blade mixer and an activating agitator to prepare backfill. Cement and ground slag are added to tailings for strength development. Two scopes have been filled and the pillars have been effectively mined out during the field trial. The application of innovative total tailings backfill technology is a new concept at the mine. Detailed planning has achieved a close integration of mining, milling and backfilling. Full mill tailings, with or without rock, are disposed of underground in a continuous process to fill, totally and systematically, the cavities formed by mining.

Jan 1, 1998

By William C. Spindler

Five industrial installations of large lead-acid battery energy storage systems in operation in the United States, West Germany and the 'Republic of South Africa will be described. One example is for a deep mine shaft in which air ventilation and personnel evacuation require the highest reliability for emergency power. The battery system is designed for additional cost-effective benefits of peak load lopping and reactive power control. Commercially available lead-acid batteries of the following types are in use1 traction, truck, submarine, high power, and gel. Electrode grids of both the calcium and antimony alloy types are used. Applications include deep and shallow cycling as well as float and intermittent use. The advantages of sealed lead-acid batteries in UPS (uninterruptible power source) systems are well established throughout the world, and such system suppliers could readily develop markets for industrial emergency and peak power lead-acid storage battery installations.

Jan 1, 1990

The problems of the as-built water supply system are discussed. Recent modifications to the collection dams and the water cleaning station using wedge wire screens to resolve these problems are outlined.

Jan 1, 1978

By John Demol

Monazite, a rare earth and thorium phosphate mineral, is one of the major minerals processed for extraction of rare earths. Industry practice for treating monazite concentrates is to use either a sulfuric acid bake or caustic conversion route. In the sulfuric acid bake, monazite concentrate is mixed with concentrated sulfuric acid and roasted. The rare earth phosphate mineral is converted to rare earth sulfate which dissolves in a subsequent water leach. As the bake temperature increases above 300 °C, thorium becomes less soluble. Although acid baking is practised in industry, the bake reactions are not well understood. A combination of chemical analysis, XRD and SEM-EDS was used to identify reaction processes occurring during sulfuric acid baking of a 93 wt% monazite concentrate between 200 °C and 800 °C. The effects of these reactions on the leachability of the rare earths, thorium and phosphate were also examined.

By Tuan Nguyen, Dirk Hummel, Ruilin Yang

In a tunnelling site in Japan, it was found that detonators failed to initiate with their shells and primary explosive intact. Their capacitors, however, were discharged due to some damage on the application-specific integrated circuits (ASICs). These detonators are distinctly different from other commonly observed failures, where the shells are rather crashed due to excessive dynamic pressure received from neighbouring blastholes which fired earlier. Such incident has not been reported elsewhere. Detonator failures during a blast are deemed not safe and can cause disruption on the project productivity. It is therefore desirable to understand the origin of such event. Various measurements were conducted to diagnose the problem, but the root cause had yet to be identified. This paper applies a discovery from a 60-year-prior-laboratory experiment and formulates a theory that could explain the observed detonator failure and predicts the measurements and observations.

Feb 6, 2023

By Toshihiro Kuzuya

A hydro metallurgical process has been developed for the recovery of metal values such as Co, Ni and rare earths from the electrode materials of spent nickel metal-hydride(Ni-MH) secondary battery. MmNis_xCo. (Mm : Misch metal) intermetallic compound could be separated from the electrode materials mixture by sedimentation. A typical chemical composition of MmN5-xCox was approximately, in mass%, 56.0%Ni, 13.4%Ce, 10.6%La and 7.9%Co. The time dependency of leaching intermetallic compound with sulfuric acid solution was examined with processing factors such as sulfuric acid concentration, temperature and agitation intensity, The leaching of rare earth metals proceeded very rapidly, reaching completion in less than 1.8ks. On the other hand, the slow leaching of nickel was observed. The percent of nickel leached at 328K could only reach about 70%.

Jan 1, 2003

By Zhucheng Huang, Ronghai ZHONG, Tao Jiang, Jun ZOU

The method of reduction roasting and magnetic separation of low-grade, micro- fine disseminated refractory iron ore following granulation with coal produced unexpected success. Pellets of iron ore with diameter between 3 and 8mm were granulated with coal, bentonite and water. The raw pellets and reduction products were analyzed by scanning electron microscopy and x-ray diffraction. Results show uniformly distributed coal powders inside the pellets improved the kinetics of the reduction process and accelerated the reduction rate. Reduction time was higher at temperatures below 890℃, which resulted in the formation of substantial amounts of fayalite. When temperature was increased, micro- fine hematite was then quickly reduced to iron metal and the amount of fayalite decreased sharply. When pellets were reduced at 950℃ for 25min, reduction products with 56.73% metallization rate were obtained. After grinding and magnetic separation, a concentrate with 72.18% Fetot was obtained.

Jan 1, 2015

By Joseph J. Wallace

1. From the standpoint of known recoverable reserves, the following is the order of importance of the beds: Upper Kittaoning, Lower Kittanning, Upper Freeport, Lower Freeport, Middle Kittaning, Clarion, Pittsburgh, and Redstone. 2. mown measured and indicated reserves in all beds, based on a minimum thickness of 14 inches and on 1,800 tons per acre-foot of coal in place, me estimated at 1,859 million short tons as of January 1, 1952. Of this, 1,351 million short tons me in beds 28 inches and more thick. Areas in each bed were omitted from the estimates because available data relative to the bed characteristics are too meager to make an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.

Jan 1, 1953

By I. Anazia

Selective fatty acid flotation of carbonate gangue from sedimentary apatites was achieved under acidic pH's without a specific apatite depressant and without conditioning the pulp with the collector. Concentrates (35-38% P205, 0.8-1% MgO) with high recoveries (80-85%) were produced from Indian and Chinese dolomitic ores. The calcareous and/or dolomitic-siliceous phosphate ores of South Florida and Utah required two flotation stages: one for carbonate removal, as mentioned above, and the other for phosphate recovery from siliceous gangue. Preliminary tests on the South Florida ore gave concentrates analyzing 29% P205 and 0.8% MgO with a P205 recovery of 76%. Data are also included showing the applicability of the process to the dolomitic-calcareous-siliceous Western U.S. phosphate ore from Utah. A concentrate obtained from this ore assayed 30% P205 and about 1% MaO.

Jan 1, 1987

By Zengjie Wang

Investigation on hydrochloric acid leaching of the ilmenite from Panzhihua, China was carried out to prepare synthetic rutile. The leaching parameters were optimized to obtain high content of TiO2 in the products. The experimental data suggest that an optimum leaching can be realized with 30% acid, a solid/liquid ratio of 1/4 at 95°C for 4h, and ore ground for -400 mesh size. After the acid leaching, an additional alkaline leaching process using hot NaOH solution was performed, and then the products was in grain form followed by heat treated at 900°C for 2h in order to extract Si and increase the particle size of synthetic rutile. The final product has a high content of TiO2 (about 95%), a low content of chlorine consuming elements (total CaO+MgO =0.07%) and a suitable particle size distribution for chlorination process.

Jan 1, 2008

By W. Perkins

The Smoky Canyon Mine has recently installed a PROMPTED GAMMA NEUTRON ACTIVATION ANALYSIS (PGNAA) on-line analyzer as part of a long-term advanced process control program. The on-line analyzer was adapted from a continuous dry analyzer and a large on-stream wet analyzer to a compact, multiplexed 3" slurry analyzer. The analyzation feed system utilizes a multiplexer system to accommodate up to fourteen (14) different plant process streams. The corresponding sampling system also provides for dewatering of sample streams too dilute for timely analysis. Key analysis includes, but is not limited to, phosphorus, aluminum, magnesium, calcium, and potassium. This data currently allows plant operations to be manually evaluated and controlled. Future development of a plant-wide supervisory control system will utilize the data for plant operations. This paper discusses the design, installation, and operation of the PGNAA on-line analyzer at the Smoky Canyon Mine.

Jan 1, 1996

By D. Belin

Treatment of dilute acid mine drainage and similarly polluted water is becoming increasingly complicated. The pressure of economics is now exacerbated by legislation which classifies as hazardous waste the precipitates from conventional lime treatment plants. Since acid mine drainage invariably contains sulfate ions, one solution is to use anaerobic Desulfovibrio type bacteria to reduce the sulfate into sulphide ions which could then be used to precipitate out the heavy metals. Results are presented for both batch flask cultures and continuous column tests. Compost was used as the bacterial substrate in the column test which simulated heaps. Conditions changed from aerobic to the required anaerobic deep in the columns. Polluted feeds (up to 700 mg/l zinc) gave effluent containing well below I mg/l zinc over extended periods. Direct transfer of sulphide ions through a stream from an isolated container of bacteria is a good alternative.

Jan 1, 1991

By Yi Luo, Jian Yang, Hua Jiang

Surface subsidence induced by underground coal mining activities, especially longwall mining operations, can cause various problems to interstate highways ranging from structural integrity to drivability to safety. Accurate subsidence prediction, correct influence assessments and effective mitigation measures are the keys to ensuring the safety of highway traffic. The surface subsidence prediction program, called comprehensive and integrated subsidence prediction model (CISPM), was developed based on the principle of influence function method and has been validated with a large number of subsidence measurements. In this paper, the techniques to use the predicted final surface movements and deformations for assessing their influence on the integrity and functionality of highway structures — such as road surface pavements, concrete slabs and transverse joints — vehicle dynamics, comfort level and drivability are presented. A number of mitigation measures to protect the highway structures and to ensure traffic safety are proposed, along with an application case.

By W. G. Davenport

The remainder of this book develops and uses mass and heat balances to describe steady"state flash smelting. Its objectives are to: a) describe the many ways a flash furnace operator can produce specified products, e,g. 65% eu matte, 35% SiOz slag, 1500 K (b) determine the oxygen, air, flux and hydrocarbon fuel requirements of each method (c) show how the flash furnace can be controlled to give specified products with varying feed compositions (d) suggest how the flash furnace operator can maximize profitability while producing specified products. This chapter develops the basiC heat and mass balance equations of steady-state ?flash smelting. It then adapts the equations to industrial feed materials .and products. Lastly it determines the amounts of oxygen and flux needed to produce molten matte and 35% SiOz slag from chalcopyrite concentrate in an Inco oxygen flash furnace,

Jan 1, 2001

By Rameshwar Sreenivasan

This paper presents a sustainability analysis of Selective Laser Sintering (SLS) from an energy standpoint. Data of electrical power consumed by the system over an entire build were acquired using a LabVIEW 8.6 circuit. The power drawn by individual subsystems was also measured, and an energy balance was performed. These data were then used to arrive at a Total Energy Indicator of the process with the help of a specific type of Environmental and Resource Management Data (ERMD) known as Eco- Indicators, which indicates the level of sustainability of the process.

Jan 1, 2010

By Roy H. Werner

The environmental demands on the mining industry coupled with rising production costs have created a need for a low cost sludge removal system. The HYDRA* system meets these demands by offering a unique means of removing settled solids from the bottom of a clarifier or a thickener. This underflow system combines experience and proven concepts to form a low cost sludge removal system. The HYDRA system incorporates a flexible design that can be adapted to any settling area. The components are readily available and cost less than a conventional clarifier or thickener. Existing technology developed by preparation engineers provides for retrieval and recovery of mine preparation plant refuse. However, past retrieval methods have been extremely costly. The HYDRA system, because of its low cost, makes the complete process of retrieval and recovery economically feasible. This allows wasted resources to be converted to a saleable product.

Jan 1, 1975

By Osamu Takeda

A decomposition process for PCBs by using basic molten salts as a reaction field was investigated in order to establish a safe, simple and highly efficient decomposition process for polychlorobiphenyls (PCBs). PCB containing chlorine (e.g. 2, 2?, 4, 4?-tetrachlorobiphenyl) dissolved in n-nonane solution was supplied into basic molten salts (NaOH-Na2CO3 or KOH-K2CO3) maintained at 500-700 ?C together with the carrier gas (N2-21% O2) through an injection tube. The injected PCBs in a bubble are decomposed by the reaction with the molten salts and oxygen during rise in the molten salts. The decomposition efficiency of PCBs increased with increasing temperature and was achieved to be higher than 99.995% in a certain condition. From a series of systematic study, the effectiveness of the decomposition process for PCBs by using molten salts was demonstrated.

Jan 1, 2008