Search Documents

By Richard J. Mainiero

The Bureau of Mines investigated coal-mine-type short-delay electric detonators marketed by three domestic manufacturers to determine the accuracy of delays and the probability of overlap between adjacent de- lay periods. The Winzer index was computed and compared with the probability of overlap. A close agreement between the Winzer criterion and overlap probability was demonstrated. A permissible blasting unit capable of delivering a maximum firing energy of 4.0 J and a digital oscilloscope were used to measure the delay time with an accuracy of 20.25 ms. Another oscilloscope and a pulse transformer were used to record firing current. Experimental data indicated negligible overlap probability in detonators of shorter delay periods: periods 1 to 4, which correspond to 25 to 250 ms. However, a significant probability of overlap was detected in some detonators of longer delay periods: periods 5 to 9, which cor- respond to 300 to 500 ms.

Jan 1, 1985

By W Herrmann, R R. Large

Volcanic-hosted massive sulfide (VHMS) deposits in ancient, submarine volcanic belts of Australia include mound, lens and sheet-style Zn-rich polymetallic deposits, massive and disseminated pyritic Cu-Au deposits and disseminated, stratabound Au-only deposits. Variation in morphologies, metal ratios, volcanic environments and alteration features indicates there exists a spectrum of deposits from the classic VHMS model, to hybrids between VHMS-porphyry Cu and VHMS-epithermal end members. Zn-rich, polymetallic deposits form eitheron, or just below, the seafloor, whereas the Cu-Au and Au-only deposits form sub-seafloor by replacement of specific volcanic lithologies. Alteration zoned outwards from quartz -> chlorite -> sericite ¦ carbonate is typical of VHMS deposits across the spectrum. Quartz and carbonate alteration is dominant in the Au-only systems,chlorite alteration is commonly developed close to Cu-rich ores, and sericite and carbonate alteration zones are well developed in the stratiform Zn-rich ores. The most useful geochemical vectors for Zn-rich ores are the alteration index [AI=100(MgO + K2O)/(MgO + K2O + CaO + Na2O)], the chlorite-carbonate-pyrite index [CCPI=100(MgO + FeO)/(MgO + FeO + K2O + Na2O)], Mn content of carbonate, Mg/(Mg+Fe) ratio of chlorite,whole-rock Tl, Sb and Ba/Sr ratio, S34S of pyrite, and whole-rock S18O. The most useful vectors for pyritic Cu-Au ores are AI, CCPI, S/Na2O ratio, Na content of white mica, and Fe content of carbonate.

Jan 1, 2002

Paiam is a new township in the high mountains of Papua New Guinea built in association with the Porgera Joint Venture mine, one of the world's largest and most remote open cut gold mines. The Paiam town project is an interesting and genuine attempt at building sustainability into a community associated with a mine. A result of a tri-party agreement between a resource developer, government and land owners, this town is a good example of appropriate utilisation of benefits, obtained from resource development, directed at achieving a sustainable environment at local and regional levels.   Mining brought technology and income to the region, although as most mine staff fly directly in and out, local landowners considered there was a limited flow of benefits within the nearby townships. An agreement with government and mine was reached that more mine personnel and their families be housed locally. In 1998, we, a firm of Landscape Architects and Heritage Consultants based in Cairns, Queensland, were engaged to assist develop the fledgling town of Paiam into a livable and sustainable town and to produce material that would convey that information to stakeholders.   The design focused on establishing a sustainable town, with livability, urban form, aesthetics and opportunities for economic, social and cultural development. Aiming to be a livable town for locals and mine staff it included a market place designed as a focus for town life, essential for social cohesion and economic opportunities.   Located at 2200 m on steep rainforest clad topography, the town development has been laid out using an appropriate urban form based on organic village layouts. Clusters of houses allow for a common public area so children's play is monitored assisting with a sense of community similar to a traditional defensible village. Aesthetical consideration helps in developing community pride whilst maximising potential for development of a tourist industry.   Opportunities for ongoing economic development were incorporated in the design and construction process. These included developing skills and trades to service the region and to provide skills, development, income opportunities and infrastructure to last beyond mine closure. Administration procedures were set in place to form the basis of good governance.   The shift from traditional subsistence lifestyle to a sustainable community with traditional attributes was the project's goal and is being achieved.

Jun 1, 2010

Based on the examination of thirty sets of contiguous matte and slag samples taken from industrial nickel smelters a relationship is predicted between oxidic nickel in slag, oxygen in matte and the Ni/Fe ratio in the matte. Oxidic nickel in the slag is found to increase with an increase in oxygen content of a matte of constant Ni/Fe ratio, and it is proposed that the relationship may be used to predict nickel solubility in slag from a knowledge of matte composition alone.

Jan 1, 1980

An Innovative Process for Comprehensive Utilisation of Clay-Vanadium Ores By adopting conventional processing technologies such as flotation, gravity concentration, and magnetic separation, it is difficult to enrich vanadium mineral effectively. At present, vanadium extraction process usually has not the mineral processing enrichment procedure, but rather uses direct hydrometallurgical process: roasting - leaching - precipitating vanadium for obtaining high quality V2O5 product. But it results in problems, for instance, high consume of auxiliary materials like acid and alkali, serious pollution and high cost of vanadium extraction. In the project study on the ore of a certain clay vanadium mineral, by adopting the test process: scrubbing raw ore with reagents added in - dispersing and segregating with reagents - grading enrichment, vanadium concentrate product with higher grade was made by virtue of reagent's selective inhibiting, and the purpose of upgrading the raw material used for vanadium extraction with hydrometallurgical process is achieved. The process technology obtained from project study features simple process structure, low equipment investment, low cost of mineral processing and pollution-free to environment. It provides high efficient and practical technology for the comprehensive utilisation of clay vanadium mineral, and has a prominent prospect for its popularisation and application.

Sep 13, 2010

By J. C. Pandey

The paper highlights the experimental investigations to characterize texture and plastic strain ratio r-Bar in auto grade steel sheets by ultrasonic measurements, whereas attempts were made to characterize interlamellar spacings in pearlite, tensile stresses and torsional properties in prestressed concrete wires by eddy current measurements. Good correlations were obtained between the testing parameters (such as ultrasonic attenuation and velocity in case of steel sheets as well as eddy current out put voltage and phase angle in case of steel wires) and the materials properties (such as texture, plastic strain ratio r-Bar, interlamellar spacings in pearlite, tensile stresses and torsional properties). 15 MHz normal direct contact and 20 MHz delay line normal shear wave probes were used for ultrasonic measurements. Eddy current measurements were done using an absolute coil probe with variable frequency selection. The experimental results show the possibility of nondestructive on line measurement of the above microstructures and properties.

Jan 1, 2010

By H. J. Haselhuhn

Selective flocculation and dispersion processes for the concentration of hematite ore are strongly dependent on the ionic content of the process water. It has been noticed that magnesium ions are more detrimental to iron recoveries during desliming and flotation processes than calcium. This phenomenon was studied by measuring the zeta potential of hematite ore at various concentrations of magnesium, calcium, strontium and barium at a pH of 11. Results show that zeta potential inverts from negative to positive at very low concentrations of magnesium ions in the solution. It takes a significantly higher concentration of calcium, ions to achieve the same effect. This difference may be attributed to the ability of magnesium ions to adsorb to all surface hydroxyl groups, whereas calcium, due to their larger size, can only adsorb to every other hydroxyl group. This hypothesis was confirmed by results similar to those seen with calcium when this test was repeated with strontium and barium ions. The tendency for calcium ions to adsorb to every other surface hydroxyl group causes higher concentrations of calcium to be less detrimental to hematite concentration processes than magnesium.

Feb 27, 2013

By R. G. Burdick, W. R. Peters

Shallow underground voids resulting from early coal mining and other resource recovery activities over the past several decades are now being recognized as a significant cause of ground subsidence problems. Uncertain knowledge of abondoned coal mines also imposes potential hazards in current underground mining operations, since water inundation or the release of methane gas is a serious hazard when mine excavation operations break into an abandoned mine. Requirements for detecting and mapping subversive manmade tunnels in previous work has led to the development of a surface-operated automatic earth resistivity survey system and associated computer data reduction process for military applications. Field demonstration tests of this system have resulted in successful detection of tunnels at depth-to-diameter ratios greater than 10 to one. Under the sponsorship of the Bureau of Mines, a similar high-resolution earth resistivity system was designed and constructed for use as a potential means of detecting abandoned coal mine workings. The hardware and software aspects of third new system are described together with applications of the method for surveying and mapping abandoned coal mine workings. Field tests are presented to illustrate the detection of both air-filled and water-filled mine workings.

Jan 1, 1984

By Richard E. Danell

"Blasting is a principal step in the surface mining process for breaking and, in the case of overburdencasting, moving rocks and minerals. As many surface mines are coming to the end of theiroperational life, blasting can once again play an important role through the earthmoving operationsrequired to rehabilitate the minesite. Since blasting is such an energetic and destructive process, itis difficult initially to envisage its use in rehabilitation. However, blasting has found applications inmany civil engineering projects aimed at rehabilitation, including well digging, channelling and soilcompaction. For surface mine rehabilitation, the main purpose of earthmoving operations is toproduce a stable landfonn that will sustain revegetation. In particular, blasting can be applied toreducing the slope of steep walls left by quarrying and open pit mining through a modified form ofthe overburden casting technique. Blasting can also be applied to breaking up pit floors andbenches to speed and improve revegetation of these areas (subsoiling)."

Jan 1, 1994

By M. Y. Solar, W. G. Davenport

Most of the recent growth in nickel demand has been for the production of stainless steels and virtually all of it has been satisfied by new ferronickel and nickel pig iron projects. But "good" laterite resources are more and more difficult to find: Ni grades are decreasing while Fe contents are increasing and SiO2/MgO ratios vary from 1 to 3 and even higher if limonites are included. Predicting the smelting behaviour of such ores requires a more fundamental understanding of the thermodynamics of these systems in commercial operations. One valid question is thus whether these furnaces are at thermodynamic equilibrium or not. The present paper investigates this question, compares calculated and measured O2 partial pressures and mechanical/chemical slag loss ratios and concludes that ferronickel furnaces are not at thermodynamic equilibrium. This departure from expectation is actually to the operators’ advantage: the targeted ferronickel grades can be obtained at lower reduction potentials than calculated from pure thermodynamics.

Jan 1, 2014

By Hakan Gurgenli

Many coal seams have weak shale immediate roofs that cause ground control problems. Therefore, it is important to know the properties of these shales so that preventive measures can be developed in advance. However, it is sometimes hard to understand this rock type due to its unpredictable behavior. A good example of this situation is found in two shale coal mine roofs located in the Illinois coal basin (Herrin No. 6 seam). Although, these mines are located very close to each other, one of them has many roof falls, whereas the other has no measurable ground control problems. The aim of this paper is to explain why and how one shale roof behaves worse than the other. Laboratory tests, including point load strength index, slake durability index, moisture activity index, weatherability index, water content determination, swelling strain and x-ray diffraction tests were performed to analyze the shale properties. According to these analyses, some useful correlations were found between the engineering properties, moisture-sensitivity indices, and weathering properties. Finally, mine and support design considerations based on the test results were discussed and recommendations to prevent ground control problems were given.

Jan 1, 2006

By Murali Gadde

Design of underground excavations in coal mines involves two major tasks: estimation of stresses and determination of rock mass strength. Owing to the complicated nature of rock mass, progress in its strength determination has lagged significantly compared to advancements in stress analysis techniques. Also, because of the impracticality of conducting field-scale strength tests, experimental approaches have very limited applicability in estimating rock mass strength. As a result, many empirical rock failure criteria have been developed based on observed performance of in situ rock structures. Unfortunately, all the popular rock mass strength criteria are based on data from large-scale ?isotropic? non-coal structures and thus can not be directly applied to coal mines. In this paper, an attempt has been made to adopt the popular Hoek-Brown (H-B) criterion for use with coal measure rocks. First, the H-B criterion is examined against laboratory triaxial strength data for different types of coal measure rocks. Then, procedures to estimate the H-B rock mass strength parameters relevant to coal measure rocks are suggested. Finally, a case-study has been given to show the usefulness of the proposed strength estimation approach.

Jan 1, 2007

Ore deposit modelling is becoming an increasingly accepted tool in mineral exploration. Successful models have already been proposed for several ore deposits of base metals and gold, but tin has so far received comparatively little attention, perhaps because of an excessive preoccupatioi with alluvial operations. This situation is rapidly changing and some of the world's most profitable and newly commissioned tin mines are large, primary tin deposits. Some basic principles of ore deposit modelling are briefly reviewed and the fallacy of an excessive reliance on grade tonnage diagrams based on the tin industry worldwide is discussed. The four proposed models and submodels of large, hard-rock, tin deposits focus on basic concepts such as the spatial relationship with "tin granites", depth of emplacement and the level of erosion. General concepts are drawn. The modelling of large primary tin deposits is reviewed not only in its geological and exploration aspects but also in its mining and economic implications.

Jan 1, 1986

By Victor F. Hollister

The Society for Mining, Metallurgy, and Exploration has compiled a number of exploration discovery case histories. This section in Volume 3 of the series describes the case histories of deposits found in layered rocks. Metallic and nonmetallic ore deposits described in this section include diverse minerals such as copper-nickel sulfides and carbonate-controlled base metals. Other case history compilations include epithermal precious metal deposits and porphyry systems. The importance of ores in layered rocks justifies their inclusion in a case history compilation. Mineral deposits occurring in layered rocks form an economically important class of ores. For example, most sulfide nickel ores are mined from basic layered intrusive rocks. Although the geologic setting is completely different from economic nickel sulfide concentrations, most barite produced also comes from stratiform and strata-bound ores. Zinc and lead ores importantly occur in beds in carbonate host rocks. Gold and other heavy minerals are concentrated in placer deposits. Indeed, the world's largest gold deposit, the Witwatersrand, is a fossil placer.

Jan 1, 1991

The Motor Truck Sections of the 20th Annual Automobile Shows of 1920, to be held in the 8th Coast Artillery Armory, New York, Jan. 3 to 10, 1920, and in the International Amphitheatre, Chicago, Jan. 24 to 31, 1920, will he the largest and most comprehensive exhibitions of the kind ever held. Approximately 125,000 sq. ft. of exhibition space has been alloted at each place and upward of seventy makes of motor trucks, together with trailers, pacts and accessories will be dis-played. In conjunction with these expositions, Highway Transport Conferences will be held, with sessions each afternoon and evening. Every important phase of highway transportation will be discussed by men recognized as qualified authorities. Various talks will he il-lustrated by motion pictures and stereoptican slides. Members of the Institute may apply for complimentary tickets to-S. A. Miles, Manager, 7 East 42d Street, New York City.

Jan 12, 1919

By R. A. Mantz, V. N. Balbyshev, A. N. Khramov, N. N. Voevodin

Corrosion protection properties of the hybrid organo-silicate coatings on aluminum substrate can be significantly improved by means of encapsulation of organic corrosion inhibitors within the coating material. In order to achieve sustained release of corrosion inhibitor and long-term corrosion protection, a secondary chemical equilibrium of either ion-exchange interaction with the coating matrix or cyclodextrin-assisted molecular encapsulation of the inhibitor has been employed. Several organic corrosion inhibitors, such as mercaptobenzothiazole, mercaptobenzimidazole, mercaptobenzimi¬dazolesulfonate, and thiosalicylic acid have been examined by a group of electrochemical methods including potentiodynamic scan, electrochemical impedance spectroscopy, and scanning vibrating electrode technique. It has been found that the formulations that contain ß-cyclodextrin demonstrate superior corrosion protection capabilities as the complexation equilibrium results in a continuing delivery of inhibitor to corrosion sites. The approach is considered a promising way for active corrosion protection of high-strength aluminum alloys when integrity of barrier coating is compromised.

Jan 1, 2004

The Bureau of Mines extends. a cordial invitation to all members of the Institute to visit Pittsburgh, Sept. 29 to Oct. 1, to participate in the dedication of the Mines Experiment Station. Accompanying this will be a nation-wide participation in a First-aid and Mine Rescue Contest. The Pittsburgh Chamber of Commerce will cooperate. The Institute will be represented by a special delegate appointed by the President. MONDAY 8:30. A. M. Bureau Building open for inspection. 10:30 A. M. Dedicatory Ceremonies in rear of Main Building, .4800 Forbes St. 2:00 P. M.. Special Train and Automobiles to Experimental Mine near Bruceton, Pa. 3 to 6 P. M. Mine Explosion and Inspection of Experimental Mine . and of Explosives Testing Plant near Bruceton, Pa. 6:00. P. M. Return by Special Train and Automobiles to B. & 0. Station, Pittsburgh. 8:00 P. M. Informal Reception and Organ Recital Carnegie Music Hall. Arranged by Carnegie Institute of Technology.

Jan 9, 1919

By Rudy Rogers

Gas hydrates have unique properties of storing selective gases. As much as 180 volumes of gas (standard conditions) per volume of hydrates may be stored. Recognizing the need for natural gas storage near electrical power plants for peak load use, DOE funded our laboratory to investigate gas hydrates as an economically viable storage means. Our developed process forms hydrates and self-packs the hydrates by only maintaining the gas pressure above a surfactant/water solution while hydrates form and self-pack. The laboratory process was scaled-up and demonstrated storage of 5300 scf of natural gas in hydrates. Subsequent to the demonstration, we discovered preparation procedures whereby laboratory gas hydrates could be stored at 1-atm with less than 1% decomposition over multiple days. The paper will discuss how these two advancements offer potential ways to recover vent gases as well as released hydrate gases from the seafloor. Keywords: gas hydrates, methane storage, surfactants, hydrate stability

Jan 1, 2008

[Page Officers of the Institute 5 Minutes of Twenty-first Meeting 9 The U. S. Fuel Company's Tipple at the Hiawatha Mine John M. Jennings 11 Some Experiences With Mechanical Loading in Central Pennsylvania¬ O. G. Sharrer 13 Mechanical Loading Underground- A. W. Dickinson 25 Operation by Long-Face Conveyor Method at Sweetwater Mine Glen A. Knox 39 Discussion of Mechanical Loading 44 Discussion-Safety in Mechanical Loading 45 New Steel Tipple, Spring Canyon, Utah- G. A. Murphy 46 A Theory on the Cause of Spontaneous Combustion-C. P. Crawford... 48 Rock Dusting in the West-D. Harrington 50 Mudite-L. C. Clare 57 Discussion of Harrington's and Clare's Papers 59 Material for Rock Dust-Prepared Discussion-Edward K. Judd 60 Tipple and Mine of the Columbia Steel Corporation-T. C. Harvey 63 Mechanical Stoking of Domestic Fuel-Joseph Harrington 67 The Garrison Automatic Domestic Stoker-Lloyd Garrison 70 Discussion of Domestic Stokers 71]

Jan 1, 1925

By Murali Gadde

Numerical simulation of cutter roof failure is a daunting coal mine excavation design issue. The complex progressive failure mechanisms associated with cutter failures are extremely difficult to replicate in computer models. However, this paper shows that with a proper selection of constitute behavior and implementation of cutting sequence, it is possible to realistically reproduce cutter failure using continuum models. Strain-softening material behavior and a systematic step-by-step model solving for a four-entry-and- three-crosscut model produced results that are similar to cutter patterns noticed in field. These results show that traditional modeling with geometries created in one model-step has limited applicability and may even provide misleading conclusions under some circumstances. Most importantly, the proposed modeling methodology provided some insights into the reasons for the inconsistent spatial distribution of cutters often noticed in coal mines. The modeling also revealed the usefulness of cutter mapping to determine the directions of in situ horizontal stresses.

Jan 1, 2005