Search Documents

Whether you are an employee, contractor or consultant working in the mineral industry, there are pressures to deliver the best possible performance. Technical professionals are usually driven by an internal desire to perform to a high standard because of personal pride in their profession, but there are an increasing number of external requirements to demonstrate that the actions taken were based upon reasonable grounds and that the work conformed to current best practice. People expect these best practice procedures to be followed and governments are now requiring those tendering for contracts to be registered in some way and to be participants in quality assurance schemes. One is not immune to these pressures just because you are working in a less legislatively sophisticated developing country in the circum-Pacific rim (Pacrim) region.

Jan 1, 1995

By N. A. Ziegler

A CERTAIN amount of interest has been indicated recently in the resistance to oxidation at high temperatures of iron-aluminum alloys (rich in iron). Hautman1 published a paper in which some interesting results are given. According to his paper, only alloys containing at least 8 per cent aluminum indicate a marked improvement in their resistance to oxidation. At about this aluminum content, however, alloys become brittle, which considerably reduces their commercial value. About two years ago the author performed a series of experiments, the results of which are presented here. A series of iron-aluminum-carbon alloys was prepared by melting electrolytic iron, aluminum and high-carbon iron alloy in an induction vacuum furnace.2 The list of these alloys is given in Table 1. Each alloy was forged in the ordinary way to

Jan 1, 1932

Fluid bed sulphation roasting of bismuth concentrates began at Warrego in 1980 in con- junction with the recommissioning of the Tennant Creek Smelter. This process, develop- ed by Peko Mines, is used to separate copper and bismuth by converting copper minerals to a water or weak acid soluble form and then leaching. Pilot scale testwork conducted at the Australian Mineral Development Laboratories (AMDEL) and by Dorr Oliver Pty Ltd in the USA indicated that close control of bed teaper- atures and exhaust gas composition was required to ensure high levels of soluble copper. After overcoming some initial problems, the plant now achieves typically 89 percent copper extraction. Plant capacity is 2.7 tonnes/h by design but in practice this is limited by feed analysis, air requirements, cyclone operation and calcine particle size Consideration.

Jan 1, 1984

By Thomas L. Kesler

Lithium raw materials usable with present technology consist of pegmatite ore and shallow evaporite brine. Deposits of these materials occur in many parts of the world. Those advantageously located supply the present lithium industry. Less favorably located deposits will come into production as markets expand and present sources are depleted. In this discussion, materials listed as reserves include fully explored and partly explored deposits. For those closely drilled and assayed, the data provide measurements rather than estimates, and such reserve tonnages are "proved." For deposits partly explored, the data support reserve estimates of "probable" tonnages. Materials lacking exploratory data are classed as resources, and their "possible" tonnages are inferred mostly from indirect evidence and are essentially objectives for exploration. All figures for pegmatite ore apply to total materials in the ground.

Jan 1, 1979

By Bruno Mattle, Max John

For tunnels with low overburden, the shotcrete lining is the main element of ground support, which is why shotcrete behavior is of prime importance. Following its application, shotcrete not only gains strength and stiffness with time but—if loaded at an early stage—it is also subject to creep which in turn leads to stress relaxation. For two-dimensional FE calculations, a computational modulus of elasticity of shotcrete is to be used. Based on parameter studies it was found that the modulus of elasticity of shotcrete depends on both shotcrete mix and ground behavior. While the Young’s Modulus used for young shotcrete may range from 1,000 to 7,000 MPa, the Young’s Modulus used for hardened shotcrete is best represented by a value of 15,000 MPa.

Jan 1, 2003

By B. Yarar, R. Buchan

Mineral-processing techniques were adopted for use in the separation of various plastics used in beverage bottles. A complete flowsheet, which utilized size reduction, heavy-media separation and flotation, was developed to separate PE, PVC and PET. In addition, the mixtures contained cellulose fibers (from labels) and aluminum (from bottle caps). It was demonstrated that, while heavy-media separation allows for the separation of a PVC/ PET mixture, froth flotation can be used to separate PVC and PET. For this purpose, the differential action of a pH 11 alkaline aqueous solution containing methanol and MIBC as surface-tension control agents, has been found to be a suitable flotation medium. This paper reports on some aspects of a flotation flowsheet that was developed for the separation of plastics contained in municipal solid wastes.

Jan 1, 1997

By Robert E. Delavault, Harry V. Warren

Circumstances determine whether it is better to make analyses in the field or in a permanent laboratory. The rubeanic acid test described in this article has been designed primarily for field use: it is simple and virtually foolproof, and it requires a minimum of field kit.* It is sensitive, easily detecting 4 ppm of readily extractable copper in a soil. This is by no means a quantitative test, but it is accurate enough to provide a valuable indicator of copper anomalous areas for both prospectors and field geologists. The easiest method for detecting metal deposits that do not produce visible float or stains is to make a simple chemical test for the metal in overlying soil, or in the silt of a stream that may have picked up metal farther upstream.

Jan 11, 1958

Gallery Stoping, an old but little used stoping method, has been reintroduced to workings at the Paringa South Shaft.Orebodies which are amenable to such a method are being mined in this manner with considerable advantages and savings.The advantages of gallery stoping as used at Paringa, compared with traditional mining methods are:1. constant cash flow2. low set up cost and initial stope development3. nearly 1005 recovery 4. no access problems 5. quicker tonnagesAs compared with highly mechanized mining methods, it has been found to be slower but requires less development, gives improved grade control, has less impact on the surrounding rock and fragmentation is much better, reducing secondary blasting costs.This paper examines the mining method and illustrates the advantages of gallery stoping at Paringa.

Jan 1, 1985

By N. A. Ziegler

A CERTAIN amount of interest has been indicated recently in the resistance to oxidation at high temperatures of iron-aluminum alloys (rich in iron). Hautman1 published a paper in. which some interesting results are given. According to his paper, only alloys containing at least 8 per cent aluminum indicate a marked improvement in their resistance to oxidation. At about this aluminum content, however, alloys become brittle, which considerably reduces their commercial value. About two years ago the author, performed a series of experiments, the results of which are presented here. A series of iron-aluminum-carbon alloys was prepared by melting electrolytic iron, aluminum and high-carbon iron alloy in an induction vacuum furnace.2 The list of these alloys is given in Table 1. Each alloy was forged in the ordinary way to

Jan 1, 1932

By B. Huang, H. Sevim, R. Honaker

The use of medium-to-high sulfur coals has been negatively impacted by the 1990 Clean Air Act Amendment (CAAA). In this article, a method is demonstrated that can render these coals competitive and yet compliant with Phase II of CAAA. The method uses strategic mining and optimized preparation plant operation to minimize production costs, and it utilizes advanced coal-cleaning technology and an SO2 allowance to produce a compliant coal. The method is illustrated through an example from southern Illinois. For an annual production of 3.2 Mt (3.5 million st) and with a $150/st SO2 allowance cost, it was possible to produce a competitive coal for $0.84/million Btu. The production and allowance costs were $0.608/million Btu and $0.232/million Btu, respectively.

Jan 1, 2002

The mineral sands industry in Australia can contribute much more sig- nificantly to economic development beyond the year 2000 by increased production of constituent minerals such as ilmenite, zircon, rutile, leu- coxene and monazite from existing and new resources, and especially from downstream processing to intermediate and finished products based on these resources. The end-use areas for mineral sand-based products include those products whose demand is tied to general economic growth, such as paints and plastics, and refractory bricks for the steel industry. High techno- logy applications such as zirconia ceramics and super-magnets are indica- tive of new developments in technology which provide considerable scope for expansion at higher rates than overall western world economic growth. An optimistic outlook for the industry is outlined, based upon a brief review of opportunities.

Jan 1, 1988

By Steven W. Hunt, Phillip U. Santacroce, Roger C. Ilsley

Consolidation grouting from the surface prior to mining a shaft is commonly performed to reduce groundwater inflows to a manageable rate. This paper describes the inflow reductions obtained within dolomite and limestone formations at several shafts and chambers due to grouting programs for the Milwaukee Water Pollution Abatement Program. The resulting inflow reduction factors are compared to results reported in the literature for other projects. Post-grouting pump tests are also evaluated as an aid in grouting assessment. Important considerations for estimating shaft inflows from pump test results are discussed. These considerations include loss of grouted mass during mining and influence of blasting and rock features on grouting effectiveness. This information should be helpful to design engineers and contractors who need to estimate inflows after pre-excavation consolidation grouting has been performed.

Jan 1, 1993

By J. Duarte Neto, V. M. Torres, A. Viana, G. S. P. Pereira, P. M. Andrade

There are technical and commercial limitations to using high fluorine copper concentrates in industrial copper smelters. The presence of more than 1,000-ppm fluorine affects the sulfuric acid units generally integrated to copper smelters. Price penalties are normally applied to copper concentrates with high fluorine contents. Several process alternatives to resolve this issue were studied at the Companhia Vale do Rio Doce (CVRD) Technology Center, Santa Luzia, Brazil. These alternatives included modifications to conventional sulfuric acid plants so that they can use high fluorine concentrates; removal of fluorine-containing minerals by flotation using depressants; selective leaching of fluorine minerals; and sulfuric acid leaching of the copper concentrates. As a result of this research, a hydro¬metallurgical process to remove fluorine and upgrade copper concentrates was developed by the CVRD.

Jan 1, 1999

By Eva Surová, Molák. Bohumil, Márta Polgári

The Úrkút rhodochrosite deposit and Branisko Mn showings (rancieite, manganiferous calcite), located in Lower Jurassic marine sedimentary rocks with black shale, were studied by organicgeochemical methods. Both depositional localities were affected by the Lower Jurassic Toarcian anoxic event. UrkUt shales are rich in organic matter (av. 2.94 wtOJo total organic carbon), the composition of which indicates derivation mainly from marine sources, with some terrigenous component. The shales matured in a bacterially active environment under reducing conditions of diagenesis-catagenesis. Branisko shales (~0.2 wt % TOC) with lenses of Mn oxide ore were weakly metamorphosed and their organic matter thermally degraded. The model for Mn carbonate ore formation envisages reaction of Mn derived from sediments, with carbonate generated by a bacterially mediated process of decomposition of organic matter that also involved Mn reduction.

Jan 1, 1992

By C. E. Lesher

Two processes for agglomerating fine sized ores with low temperature coke are described. One process (Orcarb) agglomerates ores with limited amounts of carbon; the other (ore-carbon pellets) pelletizes fine sized ores, using low temperature cokes as the binder. Data are presented on the products obtained when taconite, magnetite, and hematite concentrates and several titanium oxide ores were used. Reduction of finely divided oxide ores has long been a major metallurgical problem. Various methods of agglomerating, notably briquetting, sintering, nodulizing, and pelletizing, have been developed and are in industrial use. Carbon is the usual reducing agent for oxide ores and attempts have been made to agglomerate fine ores with coking coal in order to get the metallurgical advantages of intimate contact and increased particle sizes suitable for subsequent smelting or reduction.

Oct 1, 1955

By Moorrees C

The end uses of magnesia are determined by both its chemical and its physical proper- ties. There is seen to be an increasing need for products of high chemical purity. Prod- ucts containing 90-95 per cent MgO can be routinely produced by physical beneficiation and calcination of most magnesite ores, the dominant source of magnesia. However, pro- duction of grades containing more than 98 per cent MgO with low impurity levels is not readily achieved physically. Such products can only be readily produced by chemical processing techniques. This presentation outlines the types of impurities present in magnesite deposits and the general concepts that are involved in chemically upgrading them. Of the potential leachants, only hydrochloric acid and aqueous carbon dioxide appear to be commercially attractive.

Jan 1, 1987

By David M. Spatz

Team, as defined by Katzenbach and Smith (1993), is a small number of people with complementary skills who are committed to a common purpose, performance goals and approach for which they hold themselves mutually accountable. As the mining industry searches for new ore discoveries increasingly under post-mineral cover, the process of mineral exploration has taken us from prospector to geologist to multidisciplined explorer to multi-disciplinary team. Multidisciplinary exploration techniques have improved in terms of sensitivities and penetration and more than ever before each technique requires specialists with appropriate training and skills to process data and interpret results. To produce a quality product, specialists must collaborate openly and honestly in an atmosphere where the collective result takes into account the knowledge and expertise of each individual and the relationships between all pertinent data sets.

Jan 1, 1998

By Lynn B. Hales, Randy A. Ynchausti

Object-oriented technologies have been developed to more closely model the way we think about the world and our natural approach to solving problems. Higher levels of abstraction, generalization and classification are benefits of an object-oriented approach. Object-oriented programming, design, and expert systems are part of this technology which is shaping the future of real-time supervisory control. Goals of real-time supervisory control systems include: minimizing variations in process operations, improving efficiency, maximizing production, and implementing procedures for starting and stopping the process. Incorporating object-oriented technology in design, development and implementation of real-time supervisory control systems provides new opportunities for these tasks. This paper discusses some of the opportunities and challenges of implementing real- time supervisory control using an object-oriented expert system for a rougher flotation circuit

Jan 1, 1993

By J. A. Herbst, J. L. Sepulveda, J. D. Miller

Effective bismuth removal from flue dust residues has been accomplished for flue dusts from both zinc and copper smelters. Selective dissolution of bismuth, with respect to silver and lead, can be achieved by the proper manipulation of temperature, sulfuric acid addition and sodium chloride addition. Optimum levels of these variables were determined using a response surface technique to maximize the objective function: Y = %Bi/(1 + %Ag). In the case of the flue dust residue from a zinc smelter, which contains bismuth as an impurity (0.05%), 86% bismuth removal can be realized with less than 1% combined silver and lead dissolution. Similarly, in the case of flue dust from a copper smelter, which contains bismuth as a primary constituent (3.3%), 93% bismuth removal was obtained with little dissolution of silver and lead values.

Jan 1, 1977

By Waclaw Trutwin, Stanislaw Wasilewski

Application of computer-based systems for ventilation process monitoring makes it possible to widen the system functions with those connected with long-term data analysis. It allows the mine ventilation engineer to carry out necessary preventive actions. In future the wide application of computers and sophisticated expert systems together with automation equipment (like remotely controlled regulators and fans) will allow to gradually introduce minewide systems for air flow control. To achieve this goal research work is carried out using data from a mine ventilation monitoring system and methods of computer analysis of time series. With the use of digital filtering the measuring signal spectrum has been divided into three subranges components of which are important with regard to various needs of mine ventilation staff as well as to monitoring and control system functions.

Jan 1, 1991