Search Documents

By G. A. Irona

Solids injection into non-ferrous converters and furnaces is becoming increasingly important for concentrate injection, removal of impurities, and recycling of dusts and other waste materials. The fundamental design aspects of these technologies will be reviewed, including gas and particle trajectories, lance clogging, heat transfer, and mass transfer including reaction rates and mixing. The use of soda ash for removal of impurities such as antimony and selenium will be used as an example of versatility of powder injection processes.

Jan 1, 1993

By William A. Hockings

This report describes the results of laboratory studies on leaching of copper ores.tlf These studies are the first step of a program for the investigation of in situ leaching of tabular, metalliferous ore bodies.(2) The basic steps required in the development of an in situ process are: 1. Leachability - the ability to dissolve the metal values from the ore under in situ conditions must be demonstrated. 2. Ore Preparation - the ore must be prepared so that sufficient contact with the solution can be attained. 3. System Design - integrated in situ systems must be designed and studied for engineering feasibility. 4. Economic Feasibility - the economics of the system must be shown to be economically feasible and competitive. 5. Environmental Feasibility - the loss of reagents into the environment must be investigated. 6. Pilot Scale Testing - the feasibility of the system must be demonstrated on a sufficiently large scale. The studies described in this report were concerned only with the first step of the program, viz., leachability. Native and sulfide copper ores from the Michigan copper district were selected as model ores for these studies. Aqueous amnonia solutions were chosen as the solvents to be investigated. In this study carbonate (CO3, HCO3, H2CO3) was used exclusively as the anion. In keeping with custom it is referred to as carbon dioxide and concentrations are ex- pressed in terms of CO2. When leaching native copper the reaction is

Jan 1, 1976

By Alla D. Mah

The energies of combustion of zirconium carbide and hafnium carbide were measured by combustion calorimetry and the heats of combustion and formation. of zirconium carbide and hafnium carbide were derived . The results are-- ZrC AH298.15 ( combustion) = -308.60 ± 0.55 kcal /mole , AH298.15 ( formation) -47.0 ± 0.6 kcal /mole , AH298.15 = HfC (combustion ) = -306.08 ± 0.20 kcal/mole , AH298.15 ( formation) -52.3 ± 0.4 kcal /mole . = INTRODUCTION This report contains the results of calorimetric measurements to obtain the heats of formation of zirconium carbide ( ZrC) and hafnium carbide ( HfC) . The work was conducted as part of a Bureau of Mines program for determining the heats of formation of oxides , carbides , and nitrides by combustion calorimetry . Combustion calorimetry is one of the most precise calorimetric techniques . The chief obstacle to obtaining accurate heat of formation values for carbides , and the chief reason for the variation in the results of different investigators , is the lack of purity of the carbide samples . Corrections for impurities always involve assumptions which lead to uncertainties . In general , a large impurity correction is accompanied by a large uncertainty in the final result .

Jan 1, 1964

By Saeed Farrokhpay

It is known that the grinding condition has a major effect on the beneficiation characteristics of the minerals in subsequent processing, in particular, flotation. In the flotation process, particles surface and their condition can significantly influence collector adsorption and flotation performance. For example, particle shape and its surface roughness occurred during grinding may influence flotation characteristics of a specific ore. In fact, adsorption of different cationic and anionic species on mineral surfaces can be varied depending on the selected comminution procedure. The flotation performance of sulphide minerals can be detrimentally affected by the surface oxidation. The amount of surface oxidation may reduce the hydrophobicity of the mineral and makes adsorption of collectors less selective. Improved liberation may generally result in improved flotation recovery. However, this may result in finer grinding and slimes, and consequently, reduce the overall flotation recovery. This paper discusses the effect of wet and dry grinding on copper flotation of a complex Cu-Pb-Zn ore. Industrially, wet grinding is preferred due to its higher energy efficiency and owing to downstream processing requirements. In this study, series of flotation tests were conducted,and surface analysis (XPS and ToFSIMS) were performed after wet or dry grinding at two different P80 values. Mineralogical study was also conducted to investigate the liberation of valuable minerals after grinding. A higher copper flotation recovery was found for wet grinding. However, the copper recovery was increased by further grinding in both conditions (wet and dry). The results showed a higher collector adsorption on copper mineral surfaces after wet grinding. The surface analysis also revealed that the ore is slightly more oxidized after dry grinding probably due to higher temperature during dry grinding.

Sep 1, 2012

Anticipating the increasing importance of establishing working conditions on a scientific basis, the Department of Labor created the Working Conditions Service. This service is distinct from that performed by the Mediation and Conciliation branch, which deals with working conditions and industrial relations as controversial issues between employers and employees. The work of the Service is conducted through three coordinated divisions; Division of Industrial Hygiene and Medicine, Division of Labor Administration, and Division of Safety Engineering. The Division of Industrial Hygiene and Medicine will develop standards of sanitation and medical practice in industries. The personnel of this Division is detailed from the United States Public Health Service. The Division of Labor Administration will advise employers as to employment systems and labor management policies, and assist in putting into operation standard policies.

Jan 2, 1919

By Alexandre de Freitas Gomes de Mendonça, Leonardo José Silva de Oliveira, Rodrigo Seara Martins, Rodrigo Madrona Dias

No lingotamento contínuo, o pó fluxante é responsável pela formação de uma escória líquida no molde que formará um filme de escória entre a placa de cobre e a pele solidificada. As principais funções do filme são lubrificar e moderar o fluxo térmico no molde. Em particular, para aços com tendência ao agarramento, objetiva-se uma escória que potencialize uma extração térmica mais intensa em relação às escórias aplicadas em aços com tendência à depressão. O índice de basicidade do pó fluxante é o parâmetro que afeta diretamente a resistência térmica do filme de escória e, por consequência, a espessura da pele solidificada na saída do molde. Com o trabalho investigativo das melhores práticas, reduziu-se o índice de basicidade em 16,8% dos pós fluxantes aplicados em aços ultra baixo carbono obtendo um aumento de até 10,1% no fluxo de calor no molde. Além do aumento na espessura da pele solidificada, esse resultado também influenciou na estabilidade do nível de aço do molde e na qualidade superficial de placa.

Oct 1, 2019

By John L. Miller

The synthetic fluormicas may be divided on the basis of silicon content into tetrasilicic, trisilicic, and disilicic. Properties of lead and barium disilicic fluormicas were determined to characterize these two representative members of the disilicic group. Properties described include unit-cell parameters from X-ray diffraction, optical data, chemical composition, density, melting point, and mechanical and dielectric properties. Both the lead and the barium micas were typically monoclinic; neither was sufficiently cleavable to yield usable mica splittings. Both yielded polycrystalline, machinable ceramics with excellent mechanical and dielectric properties.

Jan 1, 1963

By G N. Phillips

Global annual gold production has been remarkably constant over the last decade at ~2500 t/a3. The major producers today are China (annual production over 350 t and rising), Australia (250 t), USA (240 t), Russia (200 t) and South Africa (190 t and falling); these figures are representative of recent years but approximate. Demand from jewellery, investment, industrial and dental uses has been in excess of mine production for the last decade, by approximately 1000 t/a.Ongoing exploration is the life-blood for gold mining, and more so than for many other metals. Explorers consider sovereign risk, security, labour costs, commercial terms, land availability and inherent geologic prospectivity to determine where to focus their activities. Exploration success over the last decade has been shared by established major producers like Australia, Canada and USA, several countries in West Africa, and many parts of the Pacific margin. Although gold-only deposits have dominated world gold production historically, the gold-plus types, especially copper-gold, are becoming more important.Australia experienced a major period of exploration success from 1979 that has led to annual gold production rising from 17 t in 1979 to 250 - 300 t/a recently. Today, Australia has economic demonstrated resources of over 9000 t Au, which has risen progressively from 220 t in 1979. The majority of production has come from gold-only deposits in the Yilgarn craton in the southern half of Western Australia, but there are a few large Proterozoic deposits in central Australia including Olympic Dam, Telfer and Starra, which are mostly gold-plus types with copper and gold. Large goldfields in the younger host rocks of eastern Australia include the gold-only deposits of Victoria and North Queensland, and gold-plus deposits of New South Wales.CITATION:Phillips, G N, 2013. Australian and global setting for gold in 2013, in Proceedings World Gold 2013 , pp 15-22 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By Michael G. Zabetakis

Investigation of gas explosions usually reveals that the combustible gases have come from transmission and storage facilities or from natural gas or oil wells. However, combustible gases such as methane and hydrogen can derive from biological processes. Hazardous situations have been created in the past by the use of abandoned mines for the disposal of sewage and rainwater, by the interconnection of storm and sanitary sewers, by sealing the openings in manhole covers when repaving the roadway over a sanitary sewer, and by the construction of buildings over or near garbage fill areas without adequately providing for the release of combustible gases.

Jan 1, 1962

By H. Kinilakodi

In 2008, the authors developed a methodology for identifying underground coal mines at high risk for major-hazard events. It focused on major hazard-related violations of safety standards associated with high-risk conditions. Later, using a sample of 103 mines with 2008 and 2009 data, injury measures and U.S. Mine Safety and Health Administration (MSHA) citation data were combined into a safe performance index (SPI). The SPI was used to assess the relative safety-related risk of mines, including by mine-size category. In this paper, comparisons are made of SPI-associated, normalized safety performance measures across mine-size categories, with emphasis on small-mine safety performance as compared to large and medium-sized mines. Mining Engineering, 2011, Vol. 63, No. 10, pp. 73-77. Official publication of the Society for Mining, Metallurgy and Exploration, Inc.

Jan 1, 2011

By F. Shigeyoshi

The development of pelletizing during the last ten years has continued, however, self-fluxing pellets have not been regularly and commercially produced for use in blast furnaces, except as Kobe Steel, Ltd., Japan. This paper tells about unique developments for self-fluxing pellets, and their effects when used in Kobe Steel's No. 3 blast furnace at the Nadahama Works (inner volume 1845 Nm3, hearth diameter 9.5 m)., Several phases of the pelletizing process are discussed individually, and also their relation to performance in blast furnace operation. Special emphasis is placed on proper preparation of the limestone added to the raw materials, and indurating at optimum conditions. Means of improving pellet quality by correct control of size distribution of the raw materials used in pelletizing, and indurating temperatures, are also discussed. As basicity (CaO/SiO2) of pellets increased 0. 1, coke consumption decreased 3. 8 to 4. 2 kg per ton of hot metal, when using 70% pellets in the iron burden.

Jan 1, 1969

By Tegner C. Johnson

Just a few years ago my company was referred to as the Marion Steam Shovel Company. We still make shovels, both two and eight crawler types. The eight crawler stripping shovel appears to have been replaced by the walking dragline for overburden removal and in some cases for the mineral as well. The walking dragline appeared in the coal fields in the early 1930's. It owes its popularity today to the fact that it can cope with overburden depths in excess of 100 feet and with blasted sedimentary rock, all at an 0 & 0 cost of ± 10¢/BCY.

Jan 1, 1974

By A. Zangooi, J. A. Finch

Flotation is a separation process based on the collection of particles on the surface of bubbles. Flotation machines disperse air into bubbles using a variety of techniques. The characteristics of the bubble population are strongly affected by the selection of frother type and concentration. As metallurgical results depend on the bubble distribution, the measurement of frother concentration is vital to understand and control performance. A previously developed colorimetric technique was refined to work with low solubility frothers and to increase daily analysis rate. Field-testing demonstrated that the method is robust, reliable and accurate. As well as relating frother concentration to gas dispersion measurements, the results can be used to answer operational questions including: how well a frother dissolves, how reliable and stable frother delivery is, how evenly frother is distributed down a bank, and whether frother distributes between the pulp and froth zones. Some of these points are illustrated from plant experiences. Advances in Mineral Processing Science and Technology Proceedings of the 48th Annual Conference of Metallurgists ofCIM Sudbury, Ontario, Canada Edited by

Jan 1, 2009

By C. L. Kosmoski, B. M. Eiter, B. P. Connor

"In the recent past, the mining industry has witnessed a substantial increase in the numbers of fatalities occurring at metal and nonmetal mine sites, but it is unclear why this is occurring. One possible explanation is that workers struggle with identifying worksite hazards and accurately assessing the associated risk. The purpose of this research was to explore this possibility within the mining industry and to more fully understand stone, sand and gravel (SSG) mine workers’ thoughts, understandings and perceptions of worksite hazards and risks. Eight mine workers were interviewed and asked to identify common hazards they come across when doing their jobs and to then discuss their perceptions of the risks associated with those identified hazards. The results of this exploratory study indicate the importance of workers’ jobrelated experience as it applies to hazard identification and risk perception, particularly their knowledge of or familiarity with a task, whether or not they had personal control over that task, and the frequency with which they perform that task. IntroductionAccording to the U.S. Mine Safety and Health Administration (MSHA, 2015a), 37 mine workers were fatally injured in accidents at metal and nonmetal mine sites between October 2013 and January 2015, following a record low of 16 in 2012 and in 2011. In 2014 alone, 29 mine workers were fatally injured at a metal or nonmetal mine site, and 52 percent of these fatalities occurred at a surface stone, sand or gravel (SSG) mine. In January 2015, Joseph A. Main, Assistant Secretary of Labor for Mine Safety and Health wrote to stakeholders in the metal and nonmetal mining community and identified several areas where improvement was necessary to promote the health and safety of mine workers. One area identified was an increased focus on “daily and effective workplace exams to find and fix hazards” (MSHA, 2015b).Hazard detection is challenging in the mining industry, despite the existence of regulation. Mining is a major undertaking involving the use of complex heavy machinery, equipment and processes as well as numerous and diverse worker activities that take place in a dynamic, challenging environment (Scharf et al., 2001). In other industries that are similarly dynamic and unpredictable, such as the construction industry, a large proportion of hazards go undetected (Carter and Smith, 2006). It is critical that miners are able to both recognize worksite hazards and accurately assess the risk associated with the hazards, because their health and safety depend on their deciding whether and how to remove hazards and mitigate risks."

Nov 1, 2016

By U. Olsson, M. Ramström

"The IREDES1 Special Interest Group (SIG) for drill rigs has been active since its launch during MineExpo 2000 in Las Vegas, Nevada, United States. SIG for drill rigs is responsible for the development of an IREDES drill rig profile, including the exchange of production planning, performance, and quality reporting data between various kinds of drill rigs and the databases used by the operating mine. During 2001, a first draft of the drill rigs profile was jointly prepared by drill rig suppliers, mining companies, and third-party suppliers and reviewed during several SIG meetings. The profile for prototyping projects was released in mid-2002; the first official IREDES release was based on feedback received from these projects.In 2002, LKAB and Atlas Copco decided to carry out an IREDES prototyping project using the Simba L6C production drill rig. The goal was to verify the drill rig profile and identify potential problems prior to the official release. This was done by implementing the IREDES prototype version into LKAB’s production planning and Simba rig control systems. The Simba rig control system was designed to handle drill plan and logging information coming from the mine planning system. In parallel to this, the mine production system was adapted for drill plan export and logging data import in IREDES format.This paper presents the most recent results of the IREDES prototyping project. Results from late 2002 show that the basic architecture of the drill rig profile works and that a common language for data exchange, IREDES, will be a central requirement for future mine automation.As a result of the IREDES prototyping project, the IREDES standard was approved at the IREDES board meeting held at the 2003 CIM Annual Conference and Exhibition. Soon thereafter, IREDES compliant products, including drill rigs and mine production planning systems, were put on the market."

Jan 1, 2005

By Natalie Zeleznik, Brian Hawkins, David Bradley, Rachel Gooding, Patrick Wilson, Brian Somes, Kevin Wegman

"To perform a probabilistic risk assessment (PRA), a method of quantifying the risks associated withinfrequent high consequence events, consequence models that generate representative estimates of human health consequences for a wide variety of representative scenarios are commonly used. Criteria that suitable models must possess include: (1) input requirements necessary to generate large volumes ofprobabilistic simulations; (2) the capability to output injuries with the necessary details and resolution;(3) the ability to capture the variety of different scenarios inherent in an assessment; (4) acceptable cost and computational requirements; and (5) sufficient stakeholder buy-in for community acceptance."

Jan 1, 2017

By J. E. Urosek

In October, 1990, a fire started in a large underground coal mine in Western Pennsylvania. During fire-fighting activities, an explosion occurred and all personnel were evacuated. Safe re-entry into the mine was not possible and the mine was sealed. Recovery efforts began in January, 1991 and continued until March, 1991, when permanent underground seals were installed between the fire area and the mine openings. This paper describes an extensive atmospheric monitoring program conducted by the Mine Safety and Health Administration (MSHA), Pittsburgh Safety and Health Technology Center (PS&HTC) including the analysis of mine fire gases, natural ventilation, fan pressure and air quantity distribution.

Jan 1, 1993

By A. R. Taylor Jr.

The heat capacities of a-quartz form beryllium fluoride were measured at approximately 3° intervals from 8° to 300° K., using an adiabatic calorimeter. At 298.15° K the heat capacity and entropy were 12.39 cal/deg mole and 12.75 ±0.04 eu respectively. Enthalpy measurements were made with an ice calorimeter at approximately 30° intervals on the quartz and glassy forms of beryllium fluoride between 300° and 1,200° K. A melting point of 825° K and an 0,-8 type transition at 500° K with a heat effect of 75 ca1/mole were deter-mined from the enthalpy data for the quartz-type sample. Beryllium fluoride glass crystallized spontaneously into the quartz modification at 500° K. The heat of the reaction BeF2 (a-quartz) .... BeF2 (glass) was found to be 1,125 ±16 cal/mole at 298° K by solution calorimetry. This value, when corrected to 273° K, was used to correct for the heat absorbed by the formation of glassy BeF2 when the sample was dropped into the ice calorimeter from temperatures above the melting point. Using corrected enthalpy measurements, the heat of fusion was determined to be 1.13 kcal/mole at 825° K.

Jan 1, 1965

By Shengqin Zhang, Yousef Mohassab, Feng Chen, Hong Yong Sohn, Mohamed Elzohiery, Amr Abdelghany

A novel ironmaking process is under development at the University of Utah aimed at producing iron directly from iron oxide concentrate in a flash reactor. This process will reduce hazardous emissions and save energy. The kinetics of magnetite reduction with hydrogen was previously investigated in our laboratory in the temperature range 1150 to 1400 oC at large temperature increments (~100 oC increments). Due to the significant melting that occurs above 1350 oC, the reduction kinetics was measured and analyzed in two distinct temperature ranges of 1150 to 1350 oC and 1350 to 1600 oC (~50 oC increments). Experiments were performed using magnetite concentrate particles of different sizes under various hydrogen partial pressures and residence times. Reduction degrees of more than 90 % were achieved in a few seconds at temperatures as low as 1250 ºC. Different rate expressions were needed to obtain reliable agreement with experimental data.

Jan 1, 2016

By Charles D. Litton

A new prototype ionization-attachment fire detector was developed by the Bureau of Mines for detecting combustion-generated submicrometer particulates. It is much more sensitive than the conventional ionization smoke detector, and it has the following added features: 1. A primary charging current of unipolar air ions is generated by a gold-coated, radioactive center electrode of a cylindrical diode. 2. Submicrometer particulates are flowed axially through the unipolar cloud where they acquire charge. The charged particles impinge upon a third electrode, located downstream, resulting in a current which is directly proportional to the particulate concentration. 3. Additional electrodes analyze the particulates in terms of their mobility and thus determine their size distribution. 4. A filter and cyclone assembly protect the ionization chamber against ambient dust. An analysis of conventional ionization smoke detector performance is also presented in terms of source strength, chamber geometry, and applied potential.

Jan 1, 1977