Search Documents

By T. M. Waterland

A GREAT deal of work has been done at Britannia during the past three years in improving and standardizing rounds for development headings, and the results obtained have been very gratifying. The round which has recently been adopted as a standard for all drifts and cross-cuts has, in some instances, doubled the average length of break formerly obtained. It has also increased the footage of advance per labour shift and reduced explosives' consumption. At the present time, with a shortage of skilled labour, more control is necessar7 in directing the drilling of rounds. The use of a standard round has been o great assistance to the foremen and shiftbosses. NATURE OF GROUND Most of the ground encountered consists of a moderately silicified chlorite schist, known locally as G.M.S (green-mottled schist). It cannot be termed hard ground, because a three and one-half inch Leyner will drill at an average rate of twelve inches per minute. Due to the abrasive nature of the ground, the gauge of the steel wears rapidly and in most cases one set of steel is needed for each hole. The ground is not 'free breaking and holes must be spaced correctly to obtain a maximum break. DEVELOPMENT OF STANDARD ROUND FOR THREE-SHIFT OPERATION Late in 1940, a development programme was started involving 7,000 feet of drifting, 6 ft. By 7 1/2 ft. In cross-section, in two headings. Plans were drawn up to advance the headings on three shifts. Equipment used in the headings was as follows: D.A.35 Leyner?machines, Eimco Model 12B mucking machines, nine one-ton end-dump cars, one Mancha Little Trammer on the longest heading, 20-pound rail, 4-in. 15 compressed-air line, 15-in. Fan pipe connected to 5 h. P. Coppus fan. Diamond-drill cross-cuts, 16 feet in length, were cut every 250 feet. Switches were installed at these cross-cuts and they served as passing points for the cars. One siding seventy feet in length was cut in each heading at approximately the half-way point. The cycle of operations planned was to muck out, drill, and blast each shift. Previous performance in this type of ground indicated that a daily advance of 12 feet to 14 feet might be made. However, if a better type of round could be developed, an increased daily advance would be possible. A study of the time available for each operation in a net working shift of six and one-half hours indicated that the maximum depth of round that could be mucked, drilled, and blasted each shift would be six and one-half feet. When this maximum depth was decided upon, the next problem was to develop a satisfactory round. Due to ventilation difficulties and to the short net working shift, the whole round had to be blasted at one time. In other words, no blasting of the cut-holes could be done.

Jan 1, 1942

By S. Miller, A. Krasner, M. Sizintsev, S. Schafrik, H. -P. Chiu, J. Sottile, A. Rajvanshi, Z. Agioutantis

In recent years, a great deal of effort has been put into automating mining equipment with the goal of improving worker health and safety and increasing mine productivity. Significant progress has been made in automating mining equipment such as load-haul-dumps and drills in underground environments where global positioning systems are unavailable. This paper addresses automating the task of positioning the shuttle-car (SC) under the continuous-miner (CM) coaldischarge conveyor during cutting and loading operations. A stereo depth camera is mounted on the SC. Machine learning based algorithms are applied on the camera’s output to identify the CM discharge conveyor and segment the scene into various regions such as roof, ribs, and personnel. This information is used to plan the shuttle car path to the CM discharge conveyor. The approach currently uses a 1/6th scale continuous miner and shuttle car in an appropriately scaled mock mine

Mar 2, 2022

By A. Y. Smith, R. J. Allan, E. H. W. Hornbrook, R. W. Boyle, W. Dyck

"HYDROGEOCHEMICAL METHODS in the Canadian Shield can be based on analyses of the following :(1) spring waters and their precipitates;(2) stream and river waters;(3) lake and muskeg waters;( 4) ground waters from drill holes, wells, faults, etc.;(5) waters issuing from diamond drill holes, faults, shear zones, etc. into mine workings and open pits; also analyses of precipitates associated With these waters.The first four can be utilized in both reconnaissance and detailed surveys. The last is suitable only for detailed work.For hydrogeochemical methods of prospecting to be effective, the following conditions must be present. 1. Natural waters must come into contact with mineral deposits and remain in contact with them long enough for the solution of detectible amounts of ore, gangue or indicator elements. 2. Dispersion patterns must be present in the hydrologic systems in order to trace the elements back to their source. These patterns may take the form of trains (e.g., increasing amounts of elements upstream toward t he source (s), Figure 1 ) or halos (e.g., increasing amounts of elements in bodies of water toward the source (s), F igures 2 and 3)."

Jan 1, 1971

By Lassi Klemettinen

For better understanding and maximal value utilization of the WEEE smelting process, the behavior and distribution of different trace elements must be known. In this study, the behavior of nickel as a trace element was studied in an equilibrium system with metallic copper—spinel saturated iron silicate slag (with 3 wt-% K2O)—iron aluminous spinel—gas. The experiments were conducted in alumina crucibles at 1300 °C, in oxygen pressure range of 10−10–10−5 atm. A time series of 15–60 min experiments was also conducted for investigating the formation rate of the primary spinel phase in the system. The results show that the distribution coefficient of nickel between metallic copper and liquid slag changes from approximately 70 to 0.4 along the increasing oxygen pressure range. In addition, a significant part of the nickel deports into the spinel phase. The spinel formation was investigated based on composition analysis results and visual observations from SEM-images.

By P. M. Krishna

A five-year effort by the ASTM subcommittee E10.14 on Uranium Resource Evaluation has culminated in the approval of E901-82, Classification System for Uranium Resources. The standard classification was prepared with participation of representatives from the Dept. of Energy, the Dept. of Interior's Geological Survey and Bureau of Mines, utilities, and consultants. The classification of a resource is based on level of knowledge and the economic producibility of the resource at a given time. Alpha-numeric identifiers are used rather than words to avoid confusion with existing terms, definitions, and classifications. An effort is underway to develop estimation criteria to guide users in classifying a resource according to the above format.

Jan 1, 1983

By Q Zhuo, P C. Pistorius, M N. Al-Harbi

A likely increasingly important pathway for future low-carbon ironmaking and steelmaking is the combination of gas-based direct reduction with electric furnace steelmaking (DRI-EAF route), or with electric smelting (DRI-ESF route). In the DRI-EAF route, the gangue that is present in the iron ore is fluxed and removed as slag in the melting (steelmaking) step. This is in contrast with integrated steelmaking, in which the gangue is removed as part of blast furnace ironmaking. For DRI-EAF steelmaking, the amount and composition of slag depend on the iron ore composition, flux additions and iron yield. Slag volume and composition affect phosphorus removal, foaming behaviour and the process energy requirements. In this work, heat data from a year of DRI-EAF production was analysed to test whether the expected relationship between slag volume and electricity consumption for EAF steelmaking was observed. The data include slag analyses (one sample per shift), and heatlevel information on all inputs, final steel temperature and dissolved oxygen concentration, electricity consumption, tapped steel mass and tap-to-tap time. In analysing the data, the slag volume was estimated from the assayed slag CaO concentration and CaO inputs to the EAF. The expected effect of slag volume on steelmaking energy consumption was calculated with a mass and energy balance, considering the heat of mixing of the slag. The calculated energy requirement of slag formation is in line with previous estimates reported in the literature.

Aug 21, 2024

By M. L. Matt

The Pittsburgh Safety and Health Technology Center of the Mine Safety and Health Administration has developed the Mine Emergency Responsiveness Development (MERD) program to improve the reaction and response of mine personnel in mine emergency situations. The MERD program simulates problems that may be encountered in underground mine fires, underground mine explosions or surface mine accidents. Since its inception in 1982, the MERD program has been presented to MSHA, Industry, Labor and State Government Personnel. The program is extremely versatile and is easily adapted to suit various training requirements. It gives the participants the opportunity to experience some of the emotions, frustrations and successes of a mine emergency in a controlled environment without having to be involved in one. Past participants have indicated that this training has better prepared them in actual emergency situations through increased awareness and advanced preparation of plans and resources. In 1992, a Mine Simulation Laboratory, which simulates a coal mine and metal/nonmetal mine, was built to improve training for mine emergencies and prevention and fighting of mine fires. This facility has been included in the MERD Program to provide realistic and practical training for mine rescue teams and MERD participants in advanced mine emergency operations. This paper presents an overview of the MERD program.

Jan 1, 1993

By Eberhard Werner

Existing reports on the effects of mine subsidence on water wells and springs appear to be inconsistent. Some report quick and complete recoveries to pre-mining conditions while others indicate long-term or permanent effects. It is clear that topographic and geological factors as well as precise position with regard to the mine are important in determining probable effects of subsidence on aquifers. Ridgetop aquifers which are well above regional base-level are much more susceptible to disturbance by mining activities than those located topographically lower. Effects seen are attributed largely to increased permeability, both horizontal and vertical. of the aquifer rocks. The deeper aquifers usually show short term losses or water-table declines. but the effects on the ridge-top aquifers persist for longer periods or may be permanent. Subsidence enhances permeability. so that infiltrating water moves much faster to lower levels. causing pond and stream losses and declining levels in wells as well as declining flows of springs of the higher aquifers, while increasing levels and flows of the lower aquifers. Additional effects are shifts of spring locations caused by minor tilts due to differential subsidence and redirection of shallow flows by changes of horizontal fracture permeability. These effects are seen as mining of a panel progresses beneath the site. and are often repeated when adjacent panel mining fronts pass the site. Analysis of water well level and spring flow records indicates that the effects are greatest at the edges of longwall panels in the tensional regime. These effects are amplified for locations close to topographically steep terrain and in close proximity to fracture traces mapped from medium-to small-scale aerial images.

Jan 1, 1986

By Chen Zhang

Polycrystalline Ti-rich NiTi thin films have been deposited from a single NiTi target using a DC magnetron sputtering system. Free standing film was obtained by using a single crystal silicon substrate. Thickness ofthe thin films is controlled at around 12 pm. In this investigation, the effect of deposition temperature on the microstructure and transformation temperatures of the thin films is studied. Influence of post heat treatment temperatures on the properties of the thin films is also investigated. Transformation temperatures of the thin films are determined by differential scanning calorimetry (DSC). The surface microstructure of the thin films is studied using a scanning electron microscope (SEM), and the crystallinity is determined using x-ray diffractometry. It is found that the thin film deposited on a hot substrate is crystalline even when the substrate temperature is as low as 300°C, while the normal crystallization temperature for an amorphous thin film is around 500°C. The microstructure of the film deposited on a hot substrate shows a very fine grain size. The grain size increases with increasing substrate temperature during deposition. The effect of post deposition heat treatment on grain size is minimal.

Jan 1, 1999

By Craig Ford

Inmet Mining is committed to implementing the highest corporate responsibility standards in its mining operations worldwide. Inmet is 100% owner of Minera Panama, a world-class copper project that is currently in the feasibility phase in north-central Panama. Panama has limited experience with modern mining, limited mining capacity, and the project context involves significant social, environmental and political complexity. The Project area is remote with recent in-migration of latino and indigenous people, informal and small-scale mining, local subsistence populations and considerable biodiversity value, coupled with a complex jurisdictional setting. In short, it is increasingly the kind of project mining companies are taking on because the easy projects have already been developed. With such challenging conditions, anticipating and managing social risks is critical to effective project management. To this end, between August 2007 and the third quarter of 2009 Inmet seconded Monkey Forest Consulting Ltd to the project to assist Minera Panama in building and implementing an effective, early phase external relations strategy. The team was also tasked to find and develop a locally based team that could sustain success through project development and into operations. Today?s presentation was created by Inmet and Monkey Forest and describes some of the lessons learned in implementing an effective early phase process for managing social issues.

May 1, 2010

By Wm. Reisz

There is no universal standard for Standard Operating Procedures (SOP’s). Every blasting operation has its own unique circumstances, its own methodologies and its own unique demands. It would be nearly impossible to create a one-size-fits-all document that would be totally appropriate for every blasting scenario. But there are universal objectives that should be adopted in any set of blasting SOP’s.

Jan 1, 2010

By Timothy Stark

Blasters are usually strictly liable for injury or damage caused by flyrock (trespassory invasion) and blast-induced vibrations (non-trespassory invasion). The application of strict liability to non-trespassory invasions has resulted in significant litigation that has hampered the use of blasting and the blasting industry. Stark (2002) proposes that blasters should not be held strictly liable for non-trespassory invasions but should be liable only if their conduct is proven to be negligent. This change in legal standard was proposed because improvements in blasting technology over the last thirty years allow blasting to be conducted without substantial risk of harm to property and thus the amount of harm imposed by a blast can be related to the level of care exercised by the blaster. It is anticipated that a negligence standard will reduce the amount of litigation because a plaintiff will have a greater burden to overcome. To facilitate the acceptance of a negligence standard by a court of law, this paper summarizes the standard of care using the 1977 Surface Mining Control and Reclamation Act, extensive U.S. Bureau of Mines research, and current blasting techniques, such as blasting mats. It is important for the blasting industry to promulgate a standard of care so a judge can feel confident that blasting can be routinely and systematically controlled and if the legal standard is changed from strict liability to negligence a subsequent judge or jury will be able to evaluate the level of care exercised by the blaster. This paper also suggests that the industry and/or ISEE develop and disseminate a comprehensive standard of care that courts can use to further justify a change from strict liability to negligence and evaluate the standard of care.

Jan 1, 2003

By G. M. Martinez

A cell concept adaptable to large-scale electrowinning of zirconium metal from zirconium tetrachloride was investigated by the Federal Bureau of Mines. Tests were made in twin cells, each 12 inches in diameter by 33 inches long. Electrowinning was performed in one chamber from which the electrolyte was transferred after electrolysis to the other chamber where it was renewed by the introduction of ZrC14 by direct sublimation. The formation of a salt plug in the connecting pipe provided a seal between the chambers. Optimum electrolyte composition, with respect to quality of the metal product (91 pct meeting ASTM standards except for the oxygen content) and current-carrying capability (about 350 amp) was determined to be 16.7 wt-pct NaF-83.3 wt-pct NaCl mixture plus ZrC14 equal to about 3 wt-pct zirconium. A twin-cell design incorporating the unit operations covered by this investigation is proposed.

Jan 1, 1976

By A. Chieregati

"A heterogeneity study was conducted at Erdenet Copper Mine in Erdenet, Mongolia, to determine the fundamental sampling error associated with blasthole sampling. Using a custom designed sector sampler, six large blasthole samples were collected to perform the test that was developed by Pierre Gy, to estimate the constitutional heterogeneity factor for several types of ore. The study investigated the entire sampling protocol, from mine site to analytical laboratory, and quantified the contributions to fundamental sampling error (FSE) of the various stages of sampling and sample preparation. The total relative standard deviation (RSD) of sampling error was determined to be ±32% and ±49.4% for copper and molybdenum respectively. A classical statistics analysis conducted on the data confirmed the level of RSD. About 95% of the sampling error was produced from only one step in the sampling protocol: when the 1 kg sample was reduced to 50 g sample for chemical analysis. Therefore, it is recommended that the 1 kg sample be reduced to 50g using a slightly different protocol to minimize the FSE. The 1 kg sample should be first crushed to 0.2cm size. A 250g split should then be taken and fine ground. A 50g split should then be taken from the 250g fine ground split. These two simple steps will reduce the FSE to ±7.9% and ±17% for copper and molybdenum respectively. The modified sampling protocol effectively reduces the probability of misclassification of low grade ore to zero. INTRODUCTION The Erdenet copper-molybdenum open pit mine is located in Erdenet, in Orkhon province, Mongolia. The Erdenetiin-Ovoo copper-molybdenum deposit is between 1.5 and 3 km wide, and about 25 km in length (Erdenet Mining Corporation, 2016). Chalcopyrite, bornite covellite and chalcocite are among the major minerals found in the deposit. The mine processes approximately 26 million tons of ore annually. A study was conducted to evaluate the fundamental error associated with the blasthole cuttings and sampling protocol at the mine. The open pit mine uses 215mm diameter Russian drills to drill 17.5m holes for 15m benches. The total weight of blasthole cuttings for a 215mm diameter hole and 15m bench height is between 1.5 and 2 tonnes. This amount of sample is difficult and time consuming to collect and analyze. Therefore, a sector sampler was designed for the Russian drills to collect large samples that were representative of the blasthole cuttings (Ganguli et al., 2016). In order to eliminate the delimitation and the extraction errors, researchers consider sector samplers to be ideal for sampling blastholes (Pitard, 2008; Chieregati and Pitard, 2009). This method was intentionally more rigorous than the blasthole sampling protocol at the mine to ensure that the blasthole cuttings were properly sampled. This study was part of a broader study that also looked at the relationship between particle size and grade. The samples collected by the custom designed sector sampler were very large (195 kg on average), and therefore, sufficient for both studies. The relationship between particle size and grade has been reported in Ganguli et al. (2016)."

Jan 1, 2017

By A. Karzhau, B. Aldamzharov, Y. Tussupbekov

"This case study produced for the metal mine operating in Kazakhstan, which has ventilation controlled manually and working continuously at maximum speed to keep air flowing through each part of the mine 24 hours a day. The mine auxiliary ventilation has been designed with the maximum length of ducting systems with extra air volumes to compensate for potential leakage. The mine provided auxiliary ventilation to all production stopes even to those, which for various operating reasons become temporarily inactive. However, mine safety has to consider risks associated with the deficit of fresh air for mine gases dilution and removal. The mine needs additional investments for re-designing ventilation network and therefore needs to estimate financial risks associated with it. The aim of this study is to conduct risk analysis for ventilation network optimisation processes at the operational metal mine in Kazakhstan. Mine ventilation surveys were undertaken for validation of the computerised ventilation model. The mine ventilation network modelling has been undertaken to be compliant with Kazakhstan mining regulations. Results of the mine ventilation optimisation processes were analysed in terms of financial risks for investments into reconstruction of the ventilation shafts, extension of the ventilation network, variable speed fans and automated regulators. Savings were resulted from improving ventilation system efficiency by reduce airflow in areas without mining activity and redistributing existing ventilation capacity. Based on savings derived from the optimised ventilation network an additional NPV has been received. Stochastic modelling use Monte Carlo simulation producing representation of possible outcomes for the additional NPV considering electricity pricing as a major variability. As result probability distribution for the optimised ventilation network demonstrates the additional NPV in a range of 1.6 - 2.2 million US$ in the corresponding defined value of 90%. Moreover, there is only 5% chance that the additional NPV to be less than 1.5 million US$. Conducted risk analysis for ventilation network optimisation processes gives considerations on volume of investments into the mine ventilation system.INTRODUCTIONCosts for mine ventilation are typically increasing when mines expand to deep levels. Some underground mines in Kazakhstan still use continuously operating fans at its maximum capacity. This is not helping to save energy and costs that are in many cases very significant. This case study produced for the metal mine operating in Kazakhstan, which has ventilation controlled manually and working continuously at maximum speed to keep air flowing through each part of a mine 24 hours a day. The mine auxiliary ventilation has been designed with maximum length of ducting systems and extra air volumes to compensate for potential leakage. The mine provided auxiliary ventilation to all production stopes even to those, which for various operating reasons become temporarily inactive. However, mine safety has to consider risks associated with the deficit of fresh air for mine gases dilution and removal from the mine workings (Sabanov, 2019). The mine needs additional investments for re-designing ventilation networks and therefore need to estimate financial risks associated with it. The aim of this study is to conduct risk analysis for ventilation networks optimisation processes at the operational mine in Kazakhstan. Mine ventilation surveys for validation of the computerised ventilation model have been undertaken"

Jan 1, 2019

By R. C. Moe

Pelletizing studies were conducted to find ways of improving the metallurgical properties of acid and fluxed pellets. In acid pellets, melting temperature was controlled by the formation of low melting temperature fayalite during reduction. Formation of a permeable metallic shell during reduction allows diffusion of reducing gas to the pellet core, decreasing fayalite formation. With fluxed pellets, slag chemistry had the main influence on metallurgical properties. Mineralogical, chemical and structural transformations that occur during reduction were studied at various intervals for a number of Mesabi Range pellet types. Six pellet types were selected for further investigation based on significant differences in softening/melting characteristics. Retention of porosity in the metallic shell was found to be the overriding factor in determining softening/melting behavior.

Jan 1, 1990

By Micheal Mayhew

"This presentation will provide information and facts on the drilling and blasting within a frozen shaft using a full face methodology. The Author will briefly discuss the history of the sinking of a frozen shaft in Saskatchewan, the challenges faced, and the solutions delivered. The case study will include a discussion describing the series of events that led to the decision to adopt a full face blasting methodology. The case study will describe key elements such as the drilling pattern, hole size and depth, explosive products and blast vibration monitoring systems. INTRODUCTION During the shaft sinking process at a project in Saskatchewan, it was recommended that a drill & blast benching method be utilized. Following an evaluation of the site, the geological conditions proved amenable to a ground freezing system that would stabilize the rock formations and prevent inflows of water into the shaft (Table 1).The shaft sinking process required that the ground surrounding the proposed shaft be frozen by drilling several near vertical freeze holes radially at a specified distance from the edge of the proposed shaft excavation. This would allow for the circulation of a chilled brine solution down the freeze holes. The circulation is achieved by means of stainless steel pipes encased within each other to provide a delivery and return conduit for the brine (Figure 1). As a result of this periphery freezing, the ground within the shaft excavation is also predominately frozen.The finished internal diameter of the shaft was 5.5 meters with varying overall excavation diameters to facilitate different liner designs used for various rock formations. For the most part, the fully unsupported/unfinished excavated diameter of the shaft varied from 6.9 meters to 8.5 meters depending on the zone excavated. The challenge was that the proposed drill and blast excavation method posed a significant risk due to the potential to damage the freeze wall and pipes during blasting. The decision was made to commence the excavation through mechanical excavation (i.e. chip and cut) methods then change to a drill and blast method utilizing a split benching design. Through this process, the team encountered five main challenges: 1. Sub-horizontal geological structures and slips that affected blasting performance and sometimes resulted in a sloping surface to the top of the bench; 2. Confined working area for the crews and equipment due to a limited work area as a result of utilizing the split (half) bench drill and blast methodology; 3. Mechanical chipping and cutting of the one-meter buffer zone to the final shaft diameter; 4. Crews working on extremely slippery uneven frozen rock and ice surfaces, which affected safety and efficiency; 5. Establishing a blast vibration monitoring system to determine if the drilling and blasting of the full shaft excavation diameter were acceptable."

Jan 1, 2019

By Giorgio De Tomi, Rondinelli Sousa

Whilst all public mineral reporting codes require classification of mineral resource and reserves according to the level of geological knowledge and confidence of the estimates, companies are not required to disclose how mineral estimates and associated cashflow projections respond probabilistically to the incorporation of different types of risk events. As the level of expectations and scrutiny of investors and stakeholders continue to increase over the years, it will be essential for companies to adopt an integrated framework for sensitivity analysis to increase corporate value through better capital allocation and reduce potential losses associated with poor investment decisions. Failure in fully capturing the impact of unexpected incidents in mineral estimates and financial modeling could be extremely harmful to the business, affecting the company’s reputation, and negatively impacting the relationship with stakeholders.

Feb 22, 2026

By Jr. Watts, B. K. Cantrell, D. H. Carlson, K. L. Rubow

"The use of diesel equipment in underground coal mines is controversial because ""whole diesel exhaust"" is regarded as ""a potential occupational carcinogen"" by the National Institute for Occupational Safety and Health (NIOSH). Threshold limit values (TLVs) are recommended for the gaseous pollutants; CO, CO2, NO, NO2, SO2, and some hydrocarbons emitted in diesel exhaust. There is, however, no TLV recommended for diesel exhaust aerosols (DEA) nor is there a standard method for sampling these aerosols.The University of Minnesota and the Bureau of Mines have collaborated to develop a personal diesel exhaust aerosol sampler (PDEAS) which utilizes size selective, inertial impaction and gravimetric analysis. During the field tests of this sampler, numerous air quality measurements were conducted in underground coal mines using diesel equipment. The objective of this report is to present these data and to assess the impact of diesel face haulage equipment on mine air quality.Air quality data were collected in four underground coal mines using continuous mining methods with diesel haulage equipment. Daily samples were collected at the section intake, haulageway, and on haulage vehicles. Both full-and partial-shift samples were collected using a variety of aerosol instruments, including the PDEAS and the micro-orifice, uniform deposit impactor (MOUDI) which sample the mine aerosol diesel exhaust fraction. Two of the mines were also monitored for the major gaseous constituents found in diesel exhaust CO, CO2, NO, NO2, and SO2. These measurements were made by either collecting bag samples for subsequent gas analysis or by Palmes dosimeters.The concentrations of CO, CO2, NO, NO2, and SO2, were well below regulated levels. The mine average DEA concentration determined by the PDEAS in the haulageway for the three mines surveyed using this instrument was 0.79 mg/m3, with a standard deviation of 0.19 mg/m3. DEA contributed 65% of the respirable aerosol, at this location. These results were the same as the mean DEA concentrations calculated from size distribution measurements obtained using the MOUDI. This was 0.78 mg/m3, with a standard deviation of 0.22 mg/m3."

Mar 1, 1992

By R. N. Hunt

GEOLOGICAL and exploration work of the United States Smelting Refining and Mining Company are handled by the mines geological and the exploration divisions of a geological department under the direction of the chief geologist. The mines division at present includes, in Utah. a geologist in charge, resident at Bingham, assisted by a geologist stationed at each operation, and a small group of geologists resident at the Bayard unit, in New Mexico. The duties of the mines division include the mapping and delineation of the geology of the mines, direction of sampling and diamond drilling, and the periodic calculation of ore reserves. At Bingham an amount of underground drilling within the limestone and porphyry formations which are hosts to the ore bodies supplements and completes development by mine workings. At Bayard, five to seven drills are kept busy underground, and eight to twelve drills operate on the surface. The mines division men live at the mine and work in close co-operation with mine superintendents and foremen. Development work is discussed, initi-

Jan 1, 1948