Search Documents

By R. I. Jaffee, E. S. Bartlett, D. N. Williams

The oxidation resistance and fabricability of molybdenum powder-metallurgy alloys containing up to 20 wt pct nickel in the form of a fine dispersion were studied. The effects of dispersion distribution and of amount and type (pure nickel or nickel compounds) of additive were considered. A definite improvement in oxidation resistance was observed, but the amount of improvement fell far short of requirements for an oxidation-resistant alloy. Fabricability by hot-rolling was limited. INVESTIGATIONS at Ohio State university1 and Battelle Memorial institute2 have indicated that the attainment of a truly oxidation-resistant molybdenum-base alloy for high-temperature service, with the coincident retention of high-temperature strength and toughness, will be a difficult, if not impossible, feat. Among the most promising alloy systems studied was the molybdenum-nickel system shown in Fig. 1. Alloys in this system show good oxidation resistance at temperatures well above the normal melting point of molybdenum trioxide because of the regenerative formation of protective nickel-molyb-date (NiMoO4) on the surface of the alloy during exposure at high temperatures. Unfortunately, the required alloy content to obtain oxidation resistant molybdenum-nickel alloys far exceeds the limits of the narrow terminal solid-solution boundary, and closely approaches the peri-tectic composition involving the brittle intermetal-lic compound, MoNi. Because of the peritectic reaction, fusion alloys are characteristically brittle, since the MoNi phase, being the last to form, tends to occur as a continuous grain-boundary network around each molybdenum grain. An added problem with this system is that the protective nickel-molybdate layer formed at high temperatures is unstable, undergoing one or more allotropic modifications upon cooling. The volume changes associated with this modification during cooling are such as to cause violent expulsion of the protective molybdate coating from the surface of the piece. This is, of course, quite detrimental in material exposed to cyclic temperature during service. The research reported here resulted from an attempt to overcome the aforementioned problems associated with the molybdenum-nickel alloys primarily by controlling the amount, size, and location of the MoNi phase. By using powder-metallurgy techniques of alloy preparation and sintering the blended molybdenum-nickel powder mixtures at a temperature below the peritectic reaction temperature, molybdenum-nickel alloys with a randomly dispersed MoNi phase were produced. MATERIALS The molybdenum powder used in the preparation of alloys for this study was commercial hydrogen reduced, minus 325-mesh (Tyler) material. Master alloys, by which nickel was added, consisted of elemental carbonyl nickel powder (12 average particle size), an alloy of 50 wt pct Ni-50 wt pct Cr, and compounds of MoNi, Ni,Si, and Ni2B. The nickel-chromium powder was prepared by filing a vacuum-arc-melted ingot, separating impurities magnetically, and screening to minus 200-mesh. The MoNi powder was prepared by pulverizing a hydrogen-sintered powder-metallurgy compact to minus 325-mesh material. Further sizing of this powder for study of effects of dispersion distribution was accomplished by air classification of the minus 325-mesh powder. The Ni2Si and Ni2B powders were prepared by crushing vacuum-sintered powder-metallurgy compacts to minus 200-mesh material. EXPERIMENTAL PROCEDURE Specimen Preparation—The general procedure followed in the preparation of alloys for testing is described as follows: 1) Blending. Either hand-blending of the powders in a ceramic mortar and pestle for X 1/2 or mechanical blending was used. Hand-blending seemed preferable for optimum homogeneity. 2) Compacting. Most of the blended powders were pressed to green compacts at pressures of 15 tons per sq in. in a single-action die, although some were pressed at 80 tons per sq in. A 1 X 11/4 X 1/4-in. green compact was the standard size for oxidation test material, and 7 X 1/2 X 1/4-in. compacts were used for fabricability test specimens. 3) Sintering. All green compacts were sinteredat

Jan 1, 1959

THE question of dealing with the small quantities of copper found in a great many of the purchased ores became a factor of importance when the Sulphide Corporation decided to refine its own lead bullion, as the presence of this impurity has a marked effect on the efficiency of the de-silverizing operations of the Parkes process. Removal of the copper from the base bullion.The copper is removed from the base bullion by drossing, which collects the copper, and at the same time has considerable gold, silver, and lead values. The drassing of the bullion is done in two stages-firstly, at the smelters; and secondly, in thecopper kettles at the refinery. In both cases a "wet" dross is produced, which is subsequently "sweated" in a suitable type of furnace. When "dry" the dross is raked out and stored until enough accumulates to warrant a nUl on dross in the small blastfurnace kept for that purpose. A typical assay of the "dry" dross is as follows...WORKING THE DROSS UP TO LOW-GRADE CU-PB MATTEThe accumulated dross is treated in a small blast furnace with the necessary fiuxes, producing a low-grade Cu-Pb matte and base lead bullion.

Jan 1, 1920

By H. Hayashi, M. Yamaki, H. Hashimoto, T. Yamanashi

"In an experiment on a trial embankment, the deformation mode of the improved ground at the toe of the embankment was compared with the deformation mode of the unimproved ground. This comparison showed that the behavior exhibited by the improved ground was the same as that exhibited by the unimproved ground, despite the low improvement rate (ap = 10%) of the ground improvement. Thus, the improved ground and the unimproved ground were found to be functioning as composite ground. Further, the strain that developed in the geo-textile used for the crushed-stone mat was considerably less than the strain specified by the design strength. As a result, it was found that a crushed-stone mat can serve as a mattress.OVERVIEW OF THE TEST CONSTRUCTIONLow Improvement-Rate Soil in Combination with Crushed-Stone MatIn Hokkaido, approximately 2,000 km2 of the land is peat land, an area almost as large as Tokyo. Such land accounts for 6% of Hokkaido’s plains and 2.4% of its total land area. The peat layer is normally 3 to 5 m thick and underlain by a layer of soft, cohesive soil whose thickness may exceed 20 m. In such a ground, consolidation using cement may generate differential settlement between improved soil as a result of embankment construction or lateral deformation caused by the slipping of unimproved ground. Therefore, the improvement ratio (ap) is designed to be at least 50% by the Manual for Construction on Soft Peaty Ground (CERI, 2011 [1]). Consolidation of ground with a low improvement ratio in combination with crushed stone-mat installation is a measure for soft ground (Figure 1). In this method, soil with a lower Improvement ratio than that of conventional improved soil (e.g., ap=10%) is placed beneath the entire embankment and a “crush stone mat”, a layer of crushed stone (t=0.5 m) enclosed by geo-textile, is then placed between the embankment and the soil."

Jan 1, 2015

By Claude E. Wykes

Deep Well turbine pumps receive constantly increasing application to the problem of mining water and other fluids from great depths. Many installations of medium settings are presently operating successfully and it is felt that mach greater depths are immediately within reach. Settings and lifts in excess of 2000 feet: are not at all out of reason with present knowledge experience, and materiels; however, conditions of individual applications will govern in each case and dictate methods and possibilities to the designer. Design and operating problems of deep set -turbine pumps ire discussed together with a description of various types of equipment falling within this category. Although the deep well turbine pump has been produced In the vertical turbine pump industry for many years, the connotation of the word "deep" still remains questionable. Among the manufacturers of this type of machinery, answers to the question implying the practical limitation of setting for a deep well pump will vary to an extreme. Most pump designers are in accord that this type of equipment has not yet been exploited to its fullest degree; however, the subject is admittedly fraught with unsolved problems and un¬tried solutions so that such a discussion must necessarily derive from personal opinion and, belief., even though based on substantial experience and background. For this reason, it will be stipulated that the present writing will deal with what may be termed euphemistically ?a highly controversial subject.? During the nineteenth century, a paper was published under proper authority proving beyond question that the human body could not withstand speeds exceeding 20 miles per hour. As a limitation, this looks ' pretty ridiculous to us today. At the beginning of the twentieth century, there was not a single machine in operation that could be described as mullti-stage deep well centrifugal pump. As a matter of fact, very few centrifugal pumps of any type wire operating against heads in excess of 50 feet, since such applications were considered impractical. In the

Jan 1, 1960

By F. P. Agterberg, A. G. Fabbri

"A statistical analysis was done on the locations of 718 copper and 1 257 gold deposits in Abitibi. This area of about 20 000 square miles is one of the better-explored metal-producing areas of Canada.Patterns of clusters were studied by harmonic analysis. Several two-dimensional power spectra showed a number of distinct peaks. Sets of crest lines for patterns of interfering waves were constructed on the basis of these peaks. They pass through elongated clusters of deposits which are spaced more or less equally. For copper these periodic regularities in location may coincide with geological structures largely of Archean age (major fractures and sedimentary belts indicating synclinal structures). A directional relationship with swarms of diabase dykes of known ages and distinct attitudes indicates that the gold mineralization is, in part, younger than the copper mineralization."

Jan 1, 2014

By Daniel Richards, Dr Rob Farnfield, Dr Geoff Adderley

The 8-millisecond rule has been in use for many years as a basic technique to help minimize vibration levels from surface blasting operations. The rule was based on work carried out in the 1960’s by the USBM by recording the vibration levels from a series of test blasts in a quarry over a range of distances. This work included the firing of a series of single hole blasts and a number of single row production blasts using a variety of inter-hole delay times. The delay times employed were limited by the technology available at that time to instantaneous, 9, 17 and 34 milliseconds. There have been several papers in recent years suggesting that the use of the 8-millisecond rule is no longer required, when using electronic detonators, due to their enhanced accuracy and greater initiation pattern design flexibility. This paper examines this proposition by revisiting the original work and employing the linear superposition technique to reprocess some of the original recordings. Similar techniques are then applied to a large database of single hole vibration recordings for a range of rock types, distances, and number of decks, with calculated reinforcements compared to the minimum separations in typical patterns. The results suggest that there is some validity to the 8-millisecond rule when applied to electronic detonators but not in the way it is traditionally applied. Simple guidance is suggested for those designing blasts with electronic detonators to minimize vibration levels even if the benefits of linear superposition trials are not available.

Jan 21, 2025

By L. G. Morrell

Introduction A Self-Dumping cage which combines the features of a small skip and a cage has been used in a vertical winze between the 2,000 and 2,500 levels at the Coniaurum mine for the past three years, during which time its success has been demonstrated by uninterrupted service and low maintenance charges. lt was designed by John Reddington, mine manager, and was built under his supervision in the Coniaurum mine shops. Being new in many of its operating features, a small-scale model was made and tried before the final construction was undertaken. The mechanical performance of the model suggested a few minor changes that were incorporated in the final drawings. During its three years of use, the automatic dumping device has saved the expense of deck-handling of the cars. This actually represents a gross economy of something over four times the cost of construction and installation, which totalled $1,325. The cage, empty, weighs 2,200 pounds, of which 500 pounds represents the weight of the dumping accessory and necessarily heavier construction. Besides a considerable financial saving, the time saved in unloading increases the daily hoisting capacity of the winze. In raising ore from the 2,500 level, five minutes are required for a complete trip. Allowing one minute for the alternative of decking, we believe that the automatic dumping has increased the capacity of the winze hoist nearly 20 percent.

Jan 1, 1933

By V. Songmene, R. Khettabi, J. Masounave, R. D. Njoya

L'augmentation régulière des règlements environnementaux et de la sécurité au travail deviennent de plus en plus strictes. L'usinage fait partie des opérations industrielles qui peuvent causer des problèmes de santé au travail et sur l'environnement. La plupart des particules de poussières produites pendant toutes les opérations d'usinage à sec ou lubrifie causent des nuisances environnementales graves. Le travail propose étudie l’influence des paramètres de coupe, des alliages et des états des matériaux sur la formation des copeaux et sur la génération de poussière lors de l'usinage à sec. Deux modes d'usinage (le fraisage et le perçage) sont abordés. Une loi reliant la ténacité des matériaux aux émissions de poussières est proposée. Les effets des matériaux et de leurs conditions, ainsi que des procédés d'usinage sur la génération des poussières ont été mis en évidence. Des mécanismes de formation de poussières sont identifiés et reliés à la formation des copeaux.

Jan 1, 2006

By D. Bienstock

Using a nitrided fused-iron catalyst, the Bureau of Mines investigated the Fischer-Tropsch reaction in the oil-circulation process. The nitrided iron was quite stable and permitted the longest run obtained thus far in the oil-circulation process without the need for reactivating the catalyst--3,700 hours of operation. The effects of several operating variables--temperature, pressure, gas-recycle ratio, space velocity, synthesis-gas composition, and synthesis with and without reflux of oil to the reactor--on the production of oxygenates were studied. The importance of removing reflux oil and of high gas recycle in increasing the oxygenate content was shown. A finished gasoline containing 28 percent by weight alcohols was produced. The research octane number (RON) was 92.9 clear, increasing to 98.5 with the addition of one milliliter of tetraethyl lead (TEL). INTRODUCTION The Federal Bureau of Mines has been engaged since 1944 in a research and development program on the synthesis of gasoline from coal. Gasification of coal with steam and oxygen to yield a "synthesis gas"--a mixture of carbon monoxide and hydrogen--is being investigated at Morgantown, W. Va., and the synthesis of gasoline by catalytically reacting carbon monoxide and hydrogen over iron by the Fischer-Tropsch reaction is being investigated at Bruceton, Pa.

Jan 1, 1960

By A. T. Iannacchione

Unrecognized roof beam failures resulted in 69% of the falls of ground injuries occurring in underground U.S. stone mines from 1990 to 1996. Field investigations at 45 underground stone mines suggest that excessive beam sag or deflection is the principal unstable roof behavior characteristics associated with miner injuries. Laminated roof structures, common in most underground stone mines, allow the immediate roof to separate into distinct beams. The timely determination of roof beam deflection could provide stone miners with advanced knowledge of potentially hazardous roof. Existing methods to assess roof conditions consist of observational and monitoring techniques. Observational techniques include open drillholes, sounding, wedging, and borescopes. Monitoring techniques include scratch tools, extensometers, telltales, Miners Helpers, and Guardian Angels. 1 Miners have difficulty utilizing these techniques because roof beams are located an average of 8 m (26.5 ft) above the miner's head in environments that are dark, dusty and noisy and these deflections are measured in millimeters of movement. To help mitigate the potential for falls of ground injuries to underground stone miners, the National Institute for Occupational Safety and Health (NIOSH) has developed the Roof Monitoring Safety System (RMSS) to aid in monitoring dangerous levels of roof beam deflection. If enough site-specific information is collected and placed on highly visible maps, individual mining operations could establish general guidelines for responding to specific roof beam deflection occurrences. This would help in implementing a pro-active, comprehensive roof control plan for reducing falls of ground injuries.

Jan 1, 1999

By Guangwei Wang, Changle Zheng, Yifan Chai, Jian Guo, Weiwei Geng, Jianliang Zhang

In this paper, characteristic and kinetics of CO2 reaction with four different kinds of coke such as top-loading coke, dry quenching tamping coke, wet quenching tamping coke and semi-coke were investigated based on isothermal method. Electric resistance reduction furnace was used to heat the sample. Volume Model (VM) and Shrinking Core Model (SCM) were used to calculate the kinetic parameters and to contrast with the experimental results. The results showed that the Volumetric Model (VM) was much suitable for the reaction of top-loading coke, dry quenching tamping coke and wet quenching tamping coke, while Shrinking Core Model (SCM) was much suitable for semi-coke.

Jan 1, 2015

By T. R. Ellis

"Editor’s Note: This is an expanded abstract. The full report is available on SME’s website at http://www.smenet.org/publications-resources/ resources/sme-valuation-standards-tutorials.The author has three goals for this review of mineral valuation standards internationally.1. To place the SME Standards and Guidelines for Valuation of Mineral Properties (SME Valuation Standards) and International Mineral Property Valuation Standards template (IMVAL Template) within the global context of existing mineral valuation standards.2. To review the current status of harmonization of each International Mineral Valuation Committee (IMVAL) member’s mineral valuation standards (or code) with the IMVAL template and suggest remedies for issues found.3. To suggest future enhancements for the IMVAL Template and SME Valuation Standards, and to suggest future roles for the IMVAL and SME committees. From the author’s review, Ellis draws the following conclusions.The SME Valuation Standards comprise a minimum set of principles-based standards and guidelines for developing and reporting valuations of mineral properties (including petroleum properties) for public and private use, subject to jurisdictional requirements. The standards are also designed to provide mineral valuation guidance that supplements application of the International Valuation Standards Council’s International Valuation Standards (IVS) and the U.S. government endorsed Uniform Standards of Professional Appraisal Practice (USPAP), published by the Appraisal Foundation.The SME Valuation Standards is the first set of valuation standards developed by a minerals institute adopting and modifying the IMVAL template. As a result, the SME standards are essentially totally harmonized and otherwise aligned with the IMVAL template. IMVAL was initially conceived in 2012 as a discussion body to aid harmonization of each member’s valuation standards, by modifying to function the same. IMVAL primarily developed the IMVAL template, published in July 2016, to produce an agreed reference framework of essential mineral valuation guidance content as the goal for harmonization of the Australasian Code for Public Reporting of Technical Assessments and Valuations of Mineral Assets (VALMIN Code), The South African Code for the Reporting of Mineral Asset Valuation (SAMVAL) and the Canadian Standards and Guidelines for Valuation of Mineral Properties (CIMVal standards and guidelines). The harmonization would result from each mineral valuation standards committee modifying its standards to operate similarly to the IMVAL template, producing valuation reports with similar content and value for the same mineral property. The template is also available for other bodies to adopt and modify for their regional setting’s needs, as SME did, or use as a convergence goal when updating an existing standard."

Jan 2, 2018

The Atlanta Mine is located in east central Nevada, in Lincoln County, 116 km (72 miles) south of Ely and 80 km (50 miles) northeast of the old mining town of Pioche. From this famous district, high-grade copper ore was mined and shipped to a smelter in Wales in the 1850s; an early day lead blast furnace was also in operation. The Standard Slag Company began operations in May 1975 on the well known Atlanta Mine, which was operated by Roy Hardy in the 1930s. The mill is currently processing 450 mtpd (500 stpd) of gold-silver bearing ore. Mining by open pit is in a brecciated zone occurring between limestone-dolomites on the foot wall and tertiary rhyolites on the hanging wall. The quartz breccia is considered among the most abrasive in the world - shovel teeth must be replaced every week. Stripping ratio is 3.9 to 1.0. Because of the hard abrasive ore, the crushing plant consists of four units: two jaw crushers in series, one Hydrocone, and one Gyradisc. Mine feed to the primary crusher is limited to 610 mm (24 in.) in size. The remaining crushers work in closed circuit with screens to produce a mill feed of 6 to 13 mm (0.25 and 0.50 in.). Hardness of the ore is demonstrated by the fact that the reversible liners of the primary jaw crusher had to be replaced in early 1978 after handling only 39,000 mt (44,000 st) at a cost of $0.095 per mt ($0.086 per st). Another example of the extreme abrasiveness of the breccia ore was the total cost per ton in 1977 for all wear parts in the comminution circuit, including screens and grinding media. This amounted to $2.84 per mt ($2.58 per st). The Atlanta grinding plant consists of three ball mills to grind the 7 mm (1 /4 in.) crushing plant product to 85 to 90% minus 150 microns (100 mesh). Feed rate to the primary Tricone mill is determined by maintaining a cyclone overflow at 28 to 38% solids, which controls the grind mentioned above. A mixture of 90 and 65 mm (3.5 and 2.5 in. ) balls are charged to this primary mill. Both the secondary mills are charged with 50 mm (2 in ) balls. Total ball consumption is 2 kg per mt (4 lb per st). All three ball mills use rubber liners. Primary mill cyclone underflows are fed to the secondary mills close circuited with the same cyclones.

Jan 1, 1981

Goethite ore are the third most abundant source of iron. The overwhelming part of these ore is represented by low-grade varieties which cannot be used in iron and steel industry without preliminary beneficiation. Biomass is a renewable solid fuel, which is feasible for the substitution of coke and coal in the manufacturing due to its lower contents of harmful elements and abundant raw material sources. Utilization of biomass in iron ore sintering process as heating agent and reducing agent contributes to energy conservation and emission reduction. The biomass was mixed together with goethite ore for roasting process to investigate the effects of reduction roasting. The results show that the goethite ore is dramatically reduced and magnetized into maghemite by biomass with the biomass dosage less than 20% and the roasting temperature below 650 oC. When the goethite ore roasted with biomass, the magnetization values could be enhanced more than two orders of magnitude, meets the standard of magnetic separation, which could significantly reduce the iron beneficiation cost. Keywords: biomass, goethite, reduction, magnetization, roasting

Sep 1, 2012

By P Toor

Due to the high energy consumption of milling, it is desirable to improve the efficiency of this process. One alternative to reduce energy and material consumption while optimising production yield in mill operation is through balanced design and selection of liners. Over-design of liners leads to increased life but at a cost to grinding performance, a relationship which to date has not been studied closely. This paper provides a description of this process of liner life cycle optimization and presents initial results from the first of two life cycles being studied for a 32 foot (ft) SAG mill. The use of commercially proven high resolution laser scanning based liner shape information provided by the MillMapper® software correlated with well controlled site surveys at various points in the liner life was used as the basis for comparison. The survey data was modelled in JKSimMet to provide direct comparisons of mill performance. This potentially provides a methodology for the design of liners that maintain a favourable shape for the majority of liner life, yielding desirable production parameters such as lower specific energy consumption and higher throughput, while at the same time maintaining practical liner life cycles.

Aug 8, 2011

By Yoshinobu Fukumori, Testuya Watanabe, Futoshi Shikata, Hiroyuki Tokumitsu, Hideki Ichikawa, Masahito Miyamoto

Nano-particulate systems have attracted much attention recently in pharmaceutical field as drug carriers and functional components of pharmaceutical dosage forms. This paper describes our approaches in design and preparation of nano-particulate systems, including lipid nano-emulsions, chitosan nanoparticles and thermosensitive acrylic nanoparticles, for certain pharmaceutical applications mentioned below. The lipid nano-emulsions with their particle size smaller than 100 nm were prepared for gadolinium neutron-capture therapy (Gd-NCT) of cancer by a thin-film hydration method with sonication, and intraperitoneally injected into Greene's melanoma (melanotic No. 179)-bearing Syrian hamsters. This provided such a high gadolinium concentraton in tumor as 107 µg/g tumor (wet basis) at 48 h after administration. As an alternative gadolinium nano-carrier for Gd-NCT, biodegradable and highly gadopentetate-loaded chitosan nanoparticles (Gd-nanoCPs, 426 mTI in particle diameter and 9.3% in Gd content) were prepared by a novel emulsion-droplet coalescence technique. A significant tumor-killing effect could be obtained when Gd-nanoCP suspension was injected intratumorally twice 24 and 8 hours before neutron irradiation into B 16Fl O melanoma-bearing mice and subsequently thermalneutron was irradiated toward tumor site with a flux of 2 x 109 n/cm2/sec for 60 min. As one another application of nanoparticles, a novel acrylic composite latex with a hydrophobic core and a thermosenstively swellable shell was designed for fabricating microcapsules showing thermosensitive mode of drug release. The microcapsules with the composite latex-dispersing membranes exhibited an exceptionally rapid on-off response of drug-release in a thermosensitive manner.

Jan 1, 2000

By G Capes, L Morizzi, N Mitkas, E Jones, D Grant

This paper describes the mining setting for the sub-level open stoping (SLOS) mining method used at Olympic Dam (OD), and investigates the range of stope performance conditions encountered over 30 years of production, using a qualitative description of the factors influencing performance. Utilising a continuous improvement tool, the Plan-Do-Check-Act (PDCA) process, and a forward-looking rock mechanics program, the intent is to identify the key factors driving productivity and performance to create a stable and achievable long term mine plan.

Mar 15, 2021

By H. Salamanca

The electric operation and design features of the 11.000 H.P. variable speed SAG mill gearless drive is presented. The function of the frequency converter, control system drive and lubrication systems are described. An analysis of the harmonic characteristic in the Supply System and Motor is presented, and the dynamic development of the stator current, speed and the magnetic flux in the start-up process of the drive is evaluated. Besides, the most important aspects in the commissioning and maintenance of the drive are analyzed.

Jan 1, 1991

By P. H. Qi

Activated carbon loaded with gold from different halide solutions has been characterized by thermal analysis techniques. The mechanism of gold uptake by carbon varies from predominately adsorption for gold iodide to predominately reduction for gold chloride. TGA and DT A measurements confirm the existence of adsorbed gold-halide species within the micropore structure of carbon. These results suggest that the ration of reduced; adsorbed gold increases for gold halides in the order Au-I > Au-Br > Au-Cl. In the case of Au-I, TA results for the loaded carbon were compared with pure compounds of 12, AuI and AuI3.

Jan 1, 1996

By Luis Beltrán, Jean Ibarra, Disney Cáceres, Gary Jarama

Debido a algunas restricciones en el diseño de planta, durante sus primeros dos años de operación, Las Bambas se vio en la necesidad de implementar un sistema de control y monitoreo para la operación de los hidrociclones del área de molienda secundaria. Al utilizar tecnología acústica y técnicas de análisis de data para evaluar el desempeño de los hidrociclones en tiempo real, dicho sistema brinda información oportuna a los operadores de planta, a fin de tomar acciones que no afecten el rendimiento de la etapa de flotación de cobre. Gracias a este sistema se pudo mantener un óptimo tamaño de partícula en la alimentación a la etapa de flotación y reducir los eventos de arenamientos en celdas de flotación a causa de cortocircuitos producidos en los hidrociclones, eventos que reducen significativamente la eficiencia de recuperación de cobre en la etapa de flotación y merman la capacidad de producción de planta.

Sep 20, 2019