Search Documents

By K. J. Shoop

This study investigates the use of a horizontally-baffled column (7.6 cm inside diameter by 344.2 cm high) to reduce the ash content of a high ash bituminous coal. Tests were carried out to determine how the baffled column responded to changes in feed rate, reagent dosage, and feed quality, and to compare its performance with a conventional column installation in an operating plant. In this paper, the results of this investigation will be reviewed and discussed.

Jan 1, 1997

By Essie Esterhuizen, John Ellenberger, Dennis Dolinar

"Underground stone mines in the United States use the room-and- pillar method of mining. The stability of the roof between pillars determines the mining dimensions and size of equipment that can be used. The findings of a survey of roof span stability issues and design practices are presented, and the observed factors contributing to roof instability are discussed. Identified stability issues are evaluated, such as maximum roof span, horizontal stress, and roof beam stability. The results of field observations, roof monitoring, and numerical analyses are used in the evaluation. The importance of the first roof beam thickness and its impact on roof stability and support requirements is presented. An evaluation of the current experience with stone mine roof spans relative to international experience is presented. A step-by-step design procedure is suggested which emphazises the need to collect adequate geotechnical data, understand the immediate roof stability, select a mining direction, and meet support requirements.INTRODUCTIONIn room-and-pillar mines, the roof between the pillars is required to remain stable during mining operations for haulage as well as access to the working areas. Roof and rib falls account for about 15% of all reportable injuries in underground stone mines (Mine Safety and Health Administration, 2009). Therefore, the stability of the roof is an important safety consideration. The size of the rooms in underground stone mines is largely dictated by the size of the mining equipment. Large mining equipment is used, requiring openings that are on average 13.5 m (44 ft) wide by approximately 7.5 m (25 ft) high to operate effectively (Esterhuizen et al., 2007). The dimensions of the roof spans are largely predetermined by the equipment requirements, and design is focused on optimizing stability under the prevailing rock conditions. If the rock mass conditions are such that the desired stable spans cannot be achieved cost effectively, it is unlikely that underground mining will proceed. In addition, large roof falls can extend across the full width of a room and may extend more than 5 m (16 ft) above the roof line. These large falls are a safety hazard and can have a significant impact on mine access and production. The National Institute for Occupational Safety and Health (NIOSH) research into stone mine roof stability has focused on identifying both the causes of roof instability and techniques to optimize stability through design."

Jan 1, 2010

By F. L. Wilke

Underground mining is a very complicated and complex industrial activity. The uncertain and, in most cases, the incomplete knowledge of the geological and mineralogical nature of the deposits can cause unforeseen difficulties. For a safe and uninterrupted operation, in addition to good planning and scheduling, reliable and up-to-date monitoring and control of all processes and conditions become necessary. Today, this is even more important in view of increasingly difficult working conditions, poorer grades, and more complex and expensive machinery. In short, large capital investment and higher risk of financial losses are involved in modern-day mining operations. Monitoring and control of the underground mining process has become a very complex and difficult task in itself. Many different systems are available, and the correct choice .is of utmost importance from both the economic and safety points of view. This chapter will deal with aspects of underground production monitoring and control. There are, however, many other areas of equal importance which are covered in an excellent manner in a hand- book by Olaf (1976) on monitoring and control of underground operations.

Jan 1, 1979

By Kouji Mimura, Manabu Kishida, Minoru Isshiki

"Purification of metallurgical grade silicon (MG-Si) by the plasma-arc zone melting method (PZM) has been examined. The process consisted in the horizontal displacement of a molten zone heated by Ar- and 10%H2+Ar- plasma-arc under atmospheric pressure. This technique, especially using hydrogen plasma-arc, promoted the segregation of impurities from the head to the tail of the bar and the vaporization of impurities of higher vapor pressures. Metallic impurities such as Fe, Ti, Cr, Mn,. Cu, Al and Ca were reduced to less than 1 mass ppm at the head side of the Si bar. Non-metallic impurities such as boron, phosphorous, carbon and oxygen were also reduced by the zoning effect and, furthermore, by activated hydrogen atoms dissociated in the high temperature plasma-arc according to the following reaction: Q (in liq.Si) + 2H = H20. Plasma-arc zone melting with hydrogen plasma has been recognized to become an effective purification technique of MG-Si for the production of a low cost solar grade Si (SOG-Si).IntroductionDemand of high-purity Si for solar grade silicon (SOG-Si) is supposed to be further growing in the near future. The purity of SOG-Si required for the photovoltaic cell is more than six nines. An expensive semiconductor grade silicon (SEG-Si) with the purity of around eleven nines has been used to satisfy the demand. Development of techniques and processes for the production of a low cost SOG-Si is therefore necessary [l]. Although many purification techniques, such as directional solidification, plasmaarc melting and electron beam melting [1-6], and processes, such as carbothermic reduction of high purity silica [7], have been examined and proposed for this purpose, a more efficient and practical purification technique is still required.In the present work, the purification of MG-Si has been investigated using a plasma-arc zone melting (PZM) technique developed by the authors. Plasma-arc melting, which is well· known as a useful melting method for various metals and alloys, has been recognized to be efficient for refining and degassing several metals if hydrogen is added to the plasma generating gas, resulting in the so-called hydrogen plasma-arc. For example, deoxidation of Fe, Co and Ta [8,9], decarburization of Fe [9] and removal of metallic impurities from Zr, Ta and Fe [10-12] have been reported. This excellent refining effect is considered to be caused by dissociated and activated hydrogen atoms formed in the high temperature plasma-arc."

Jan 1, 2000

By Michel Brissette, Shaheer Sanuri, Veroljub Mihajlovic

"The main purpose of geometallurgy is to improve the mine planning by mapping hardness and throughput into the mine block model using geostatistics to eliminate the large production fluctuations caused by the ore hardness variability coming from different parts of the pit. However, not all grinding testwork available commercially can be applied to geometallurgy because of large amount of sample required and the associated cost per test. Geometallurgy is now being used in designing grinding mill but as the mining project progress, the accuracy of engineering must improve from 30-35% during the scoping study to 10-15% at the bankable feasibility stage and less than 5% for Engineering Procurement and Construction Management. For SAG milling, the SAG Variability Test (SVT) is an abbreviated version of the standard SAGDesign test developed for this geometallurgical need. The same amount of ore than the original test is ground for three cycles into an open batch SAG test and then the SAG pinion energy is predicted to the standard end point of 80% passing 1.7 mm. For ball milling, a Bond Variability Test (BVT) was also developed using the SAG ground ore from the SVT. The Bond ball mill grindability (Gpb), corresponding to the average of the net grams per revolution from the last three cycles of the Bond test, is also predicted from the third cycle. The relative error for both the predicted SAG ore hardness (WSVT) and Bond Work Index on SAG Variability ground ore (Sv-BVI), in kWh/t, averaged 5.5% and 3.8% respectively compared to the SAGDesign testwork values and are within 7% and 10% respectively from plant benchmark and within 7% from the samples sent to all partner laboratories. Both tests can be continued to measure the true hardness necessary for mill sizing. This article discusses the development of these two new tests, SVT and BVT, their potential use and accuracies in any geometallurgical program."

Jan 1, 2014

By Mark G. Aylmore, Eric J. Grimsey

Anenopyrite, both pure and in some cases associated with pyrite, was laboratory roasted either isothermally or at a constant heating rate, at temperatures mainly between 723 and 923 K and under environments of air, sulfur dioxide, oxygen and argon, as well as S02/02/H20/N2 mixtures. The mineralogy, arsenic contents and in some cases surface areas of the calcines were evaluated so as to provide an enhanced understanding particularly of the conditions under which the important transformations to pyrrhotite and magnetite occur. A thermodynamic analysis is also undertaken to rationalize the observations and provide some guidance for the operation of commercial roasters.

Jan 1, 1990

By John Nagy

The effect of low percentages of methane (0 to 5 pet.) in an air atmosphere on spark initiated explosions of coal dust was investigated. With low dust concentrations (0.1 to 0.4 oz./cu, ft.), small amounts of methane increase the explosion pressure; with larger dust concentrations (0.5 to 2.0 oz./cu. ft.), small amounts of methane decrease the explosion pressure. The rate of pressure rise of a coal dust explosion increases with increase in methane concentration; about 3 to 4 pct. further addition of methane yields a decrease in the rate of pressure rise. Convection currents created by the air or gas blast used to disperse dust produce an increase in explosion pressure and rate of pressure rise. The minimum explosive concentration of the coal dust decreases about linearly as the concentration of methane increases from 0 to 5 pct. The explosion pressure increases linearly as the initial pressure within the chamber increases. Similarities between coal dust and methane explosions are indicated, INTRODUCTION During coal mining, methane occluded in coal or adjoining strata is liberated into the mine atmosphere,4 Normally, the methane is diluted and swept away by the ventilating air. Under some conditions, through accidental disruption of the ventilation system, sudden outburst, or because insufficient fresh air is supplied to a working place, low percentages of methane may be present during mining operations. If it is permitted to accumulate, methane itself presents an explosion hazard; its limits of explosibility arc approximately 5 and 15 pct. The effect of low percentages of methane on the explosibility of coal dust was studied to provide a broader understanding of the hazards of ignition and explosion and thus to facilitate development of control

Jan 1, 1961

By AIME AIME

THE sixteenth annual meeting of the Woman's Aux¬iliary, A. I. M. E., was held Tuesday morning, Feb. 16, at the Engineering Societies Building. The meeting was well attended, there being 99 registered from the metropolitan area and 78 from the sections throughout the United States. Mrs. Sharpless, the secretary, read the minutes of the annual meeting held a year ago, after which Mrs. Bassett, the president, gave her address of welcome. Mrs. Bassett said in part: "I would like, at this time, to welcome you all to this, our sixteenth annual meeting, and to express my appreciation to all the national officers and members of the board of directors for their loyal support and for the excellent work done by the chairmen of sections and their members. It is with much pleasure that I look back upon my visits with the sections in Washington, Arizona, Northern and Southern California, Chicago, Colorado, Western Pennsylvania and Utah before I assumed the office of president. During the last year I have much enjoyed meeting with the sections in Boston, Washington and New York. It is our duty to see that the achievement for 1932 be equal to that of the year that has just passed."

Jan 1, 1932

By Jamal Rostami, Omid Frough, Wei Hu

Characterizing the abrasiveness of soil/rock and the allowable wear of hard-facing products in various conditions is a critical factor in selection of the best material for certain applications related to drilling and excavation in mining and construction industries. The Soil Abrasion Index test machine at Colorado School of Mines (CSM) is one of the recently developed unique systems capable of testing soil/crushed rock abrasion under various conditions, such as dry, wet, and saturated settings. It is also capable of testing the performance of various types of hard-facing materials in a given geo-material. This paper studies the wear properties of different hard-facing materials in various crushed rocks from a surface mining operation in the iron range region of the USA. The hard-facing materials include regular and hardened steels and six different specialized hard facings, based on chromium carbide. The soil/rock include a standard sand and two rock samples from the surface mine. Fourteen abrasion tests were conducted, where the weight loss of each hard-facing material was measured over timespans up to 1 h of testing. The results show the distinct performance differences between the steels with 17 HRC and 43 HRC hardness and the hard-facing products for this application. The results show the possibility to evaluate the abrasiveness of different rocks at a mine or construction site and the performance of various hard facings in similar working conditions. This is a practical solution for selection of the cutting tool or reinforcement of bucket lips and truck beds for comparison of relative wear life between different wear-resistant materials.

By Harold J. Polta

This Bureau of Mines publication considers the feasibility of augmenting the present transportation system by pipelining taconite concentrates from the Mesabi Range to the Chicago area. The cost of pipelining in the hypothetical system using water as the carrier is estimated to be between $3.66 and $3.97 per long ton. This appears competitive with the 1970 rail-vessel transportation rate of $4.08 even after allowing a few cents per ton for barging from the terminal to existing furnaces. Political obstacles requiring solution before such a pipeline could be built and the feasibility of using crude oil as the carrier fluid are also discussed. FORTRAN routines used to calculate unit transportation cost for specific estimated values of cost items and for a range of values are presented. The effect of deviations from estimated values of cost items on the total unit transportation cost are shown graphically.

Jan 1, 1971

By John W. Buch

At a meeting of the Anthracite Investigations Advisory Committee in July 1944 at Washington, D. C., the initial work and objectives of the Anthracite Mechanical Mining Section of the Federal Bureau of Mines were discussed. It was learned that interest existed in an improved performance of mining thin, steeply pitching beds above the gangway by mechanical methods. One company offered the use of one of its mines for experimental work, and this offer was accepted. Following acceptance, an effort was made by Bureau engineers to devise a mechanical method with a performance better than that of a new hand method proposed by company engineers for an actual mining condition. The method proposed by the Bureau was to drive 30-degree slant chutes across a 10-foot bed pitching 85 degrees. These chutes were to be advanced by using a lightweight, compressed air-powered, shearing machine of German origin that had been tried in a flat Pennsylvania anthracite bed in 1934, and which did not then prove successful because of blasting difficulties. An attempt was made to obtain one of these machines from England, where it was known machines of this type had been used. Shortly thereafter John W. Buch was sent to Europe as a member of the Solid Fuels Mission to the European Theater of Operations organized by the Technical Industrial Intelligence Committee of the Joint Chiefs of Staff. Through his efforts the Bureau of Mines obtained two such machines, known as the Eickhoff model DEK, one from England and one from Germany. This report covers the preliminary testing of these machines in order to obtain mechanical operating data for use in determining the power requirements for cutting anthracite with machines of this design.

Jan 1, 1949

By Arthur L. Miller

Recent studies suggest that trace metals emitted by internal combustion engines are derived mainly from combustion of lubrication oil. This hypothesis was examined by investigation of the formation of particulate matter emitted from an internal combustion engine in the absence of fuel-derived soot. Emissions from a modified CAT 3304 diesel engine fueled with hydrogen gas were characterized. The role of organic carbon and metals from lubrication oil on particle formation was investigated under selected engine conditions. The engine produced exhaust aerosol with log normal-size distributions and particle concentrations between 105 and 101 cm-3 with geometric mean diameters from 18 to 31 nm. The particles contained organic carbon, little or no elemental carbon, and a much larger percentage of metals than particles from diesel engines. The maximum total carbon emission rate was estimated at 1.08 g h-1, which is much lower than the emission rate of the original diesel engine. There was also evidence that less volatile elements, such as iron, self-nucleated to form nanoparticles, some of which survive the coagulation process.

Jan 1, 2007

By Craig Allan

Underground construction environments, especially those with limited airflow such as shafts, cross passages, and stations, necessitate effective dust control. This requires combining existing measures with adapted approaches for more efficient and productive operations, cleaner jobsites, and decreased worker exposure to contaminated air. This paper will discuss new configurations and trends in dust collection on Australasian infrastructure projects including WestConnex, Melbourne Metro Tunnel and City Rail Link, all of which have applied innovative methodologies for mobile at-source dust collection. Mobile dust collectors can be track-mounted dust collectors operate alongside equipment, use hydraulic stepping systems to advance with roadheaders, or compact castor-mounted units are used within cross passage confines.

Dec 1, 2022

By G. J. Conroy

This Bureau of Mines study was initiated to determine whether or not a large-scale investigation of 400-Hz applications in coal mines was justified as a means of increasing safety in operations due to size and weight reductions in portable and other mining machinery. Potential uses for 400-Hz power in mining operations are explored, and cost and size comparisons with 60-Hz systems are made. The use of variable-frequency motor drive is suggested for conveyors. The conclusion was reached that there is no significant potential safety increase due to a general size and weight reduction, as the fact of such general reduction cannot be demonstrated.

Jan 1, 1974

By William R. Bush

This paper is a presentation of findings based upon an econometric model of the world zinc industry. The model was developed as a simple but useful aid for long-run forecasting and planning purposes. A structure was developed for both simulating real zinc price effects on production and consumption, and for forecasting long-run annual zinc prices and supply/ demand levels. Moreover, a methodology is provided to incorporate the effects of: (1) historic technological advances in zinc supply, and (2) the development of the competitive plastics industry. Finally, reduced form equations are used to generate ex post forecasts to evaluate the model's performance.

Jan 1, 1979

By J. W. Leonard, D. A. Newman

Discussion by N. Standish and P.N. Standish Leonard and Newman (1989) describe concepts and plans of their forthcoming project designed to increase the bulk density of broken coal at various stages of its production and handling. This is an excellent idea and something that will certainly be useful to the coal mining industry worldwide. The authors seek to achieve bulk density increase by "reducing oreliminating, through chemical additives and engineering design, particle voidage and enhance particle consolidation trickling between the point of breakage (at the face) and loading (in the shuttle car) to increase coal bulk density and productivity." In the paper, they present some supporting results of bulk density versus moisture, with or without oil addition, from the steel industry research. Unfortunately, the paper contains many misconceptions and half-truths that detract from an otherwise excellent objective of the project of increasing bulk density by reducing particle voidage-"the bottom line evaluator." Correct. Theory Definitions Coal bulk density is the ratio of the mass of a collection of discrete particles to the volume that it occupies (ASA, 1980). There can be no possible argument about this definition. Mass and volume are readily measured both in laboratory and large scale installations. So, to obtain the bulk density, one simply divides the measured mass by the measured volume. It is here that we come unstuck as everybody who has ever had to reconcile book values with the measured stock tonnages knows. Where does the problem originate? Almost invariably in a too casual a reading of the above definition and the words "a collection of discrete particles." The word collection means "a number of objects collected or gathered together, viewed as a whole" (The Oxford English Dictionary, 1989). If one knows the bulk density of a pile of coal viewed as a whole,

Jan 1, 1991

By Thomas T. Read

THE benefits derived from stabilization of industry that might possibly be attained through some scheme of centralized economic planning have been much discussed of recent months, and opinions on the subject range from those who believe that some agency like the War Industries Board would be practicable to create and wholly beneficial in effects, to those who are equally convinced that none of the suggestions so far advanced are at all practicable, or likely to be productive of more of good than of evil. The discussion has been on the general topic, but-many of those who have written or spoken on it have introduced economic problems of the pinera1 industry; for example, Newton D. Baker, who referred to the coal industry in his address on economic planning at the Williamstown Institute of Politics on July 31, and then went on to say, "Industrial progress is made by the development of new things, but new things upset the equilibrium of any plan. Who could have planned the industrial effects of the development of the railroads, or the economic changes which you have seen attend the development of the internal combustion engine. Obviously, unless we are prepared to put world economics in a strait-jacket and, like the encyclopedists, write its full history on the theory that further progress is impossible, no such plan could be made for nations which are forging ahead as is entirely rational for nations which are still catching up."

Jan 1, 1931

By P. Gelfi, G. Hill, A. Showell, V. Martins, R. Dunne, R. Jenkins

Carbon attrition losses are not usually a prime consideration for CIP equipment selection and CIP plant design. However, the costs as a result of carbon attrition and associated gold lost with carbon can be high. Recorded carbon losses for Newcrest operating gold plants were shown to vary widely from plant to plant. The Tuckabiana plant recorded an overall loss of only 0.3g carbon /t ore which is very low by industry standards. A comparative carbon management study was undertaken by Newcrest to highlight the reasons for the excellent record of Tuckabiana operation compared to other Newcrest plants. This paper discusses the results of the comparative study and high­lights areas of concern with respect to carbon attrition.

Jan 1, 1995

By R. G. Reddy

Spent potliner is generated in the electrolytic process of reducing alumina to make aluminum metal using molten fluoride electrolytes. Spent potliner (SPL), obtained at the end of the pots life contains a small amount of cyanide and fluoride which present environmental problems. SPL became a listed hazardous waste under RCRA (K088) in July, 1990. One of the possible uses of spent potliner is as a substitute for Calcium Fluoride (CaF2) as a fluidizer in iron-and steel making and in the glass industry. A low viscosity and a low melting point are prime requirements for accomplishing the above. In the present study, viscosity measurements were performed. Effect of various additives, such as sand, limestone, dicalcium silicate dust, and MgO baghouse dust on the viscosity of SPL was studied. The results showed that with the addition of sand and limestone, very high fluidity of SPL melt can be obtained at significantly low temperatures. The results suggest that spent potliner mixed with additives could potentially be used as a substitute fluidizer.

Jan 1, 1999

By R. ZapataN.

"In the following report, Altonorte Smelter owned by Xstrata will explain its experience with its denominated furnace called ""Continuous Altonorte Reactor"" since started up in March 2002. The Reactor is the main and only smelting furnace since the operation of Reverb Furnace was stopped (15 days after the start up of the Reactor) and it can be operate with dry concentrate for injection by tuyere and wet concentrated via Garr Gun when the injection system fails. From the started up of the Reactor, three operational campaigns have been carried out where in each one they have been increased their smelting throughput and availability. The flexibility reached by the technology bath smelting has allowed a high level of smelting of concentrate and revert materials. The high availability of the Reactor and overcoming problems that were considered of high complexity like the extraction of white metal and slag, refractory campaign, etc. has allowed the Altonorte smelter to project to smelting 1,200,000 tonnes per year with its only Reactor in next year."

Jan 1, 2007