Search Documents

By Eric Forssberg, Mats Hallin

INTRODUCTION Evaluation and optimization of mineral processes has been going on since the the first plant started hundreds of years ago. A huge mass of knowledge has been collected since then. The main problem with this type of empirical knowledge of complex processes is that it is very difficult to formulate and document. The methods used for collecting the knowledge is not consistent but-varies with "he person" that does it. In the late 60's and early 70's efforts were made to use computer based techniques to evaluate process performance and to formulate process models for mineral processes. Models were developed, such as the flotation model by R. P. King (1973) which is still used to simulate flotation circuit behaviour. During the 70's. a number of mass balancing packages were developed together with process simulation packages. The industrial sector also made great efforts to develop and utilize computer based systems for process control and evaluation. The expert system that BOLIDEN created in 1974 at the Kristineberg plant was a remarkable achievement considering the hardware (CDC 3600) and the software tools (FORTRAN) available at that time. The main obstacle to successfully implement optimizing computer control of mineral processes was and still is the limited knowledge about the dynamics of complex processes. There are, however. many activities going on in this area today and it seems that the technology is very near a break through. Process evaluation is the most important tool to improve and maintain the optimal performance of a process. Today dedicated computer based techniques are used for fast and reliable screening of the processes. The stages in process evaluation consist of three basic steps: - Data acquisition, manually or by data logging. - Data refining, mass balancing and parameter calculation. - Data evaluation. The refined data can then be used for model construction/calibration and subsequently for process simulation. This paper describes two studies where the techniques mentioned above are used to evaluate and simulate

Jan 1, 1991

By Camila Barbosa Albani

Foram estudados os tipos de projeções, suas características e medidas de controle, a partir do acompanhamento de corridas na ArcelorMittal Tubarão, inclusive com amostragem e análises dos resíduos de projeção. Utilizando-se termodinâmica computacional estimou-se a viscosidade da projeção, que se mostrou muito heterogênea. Projeções ocorreram em uma faixa extensa de Si do gusa, inclusive em valores abaixo de 0,30%, com maior frequência entre 0,30% e 0,40%. As adições de minério de ferro tiveram forte influência na ocorrência de projeções possivelmente devido ao efeito conjugado de redução da permeabilidade e geração de gás. Um modelo conceitual das causas principais das projeções foi proposto e validado com observações de ocorrência de projeções tardias no sopro. Foi também proposto que as ações de controle de projeções deveriam ser ajustadas de forma a priorizar o controle da taxa de descarburação e o aumento da permeabilidade da emulsão.

Oct 30, 2017

By Qing-hua Tian, Xue-yi Guo, Fei Li

A novel process for the preparation of a-Al2O3 from secondary aluminum dross was studied. Factors including alkali dross ratio, salt dross ratio, smelting temperature, smelting time, leaching temperature, leaching time, and the solid-liquid ratio, which possibly influence the transfer of Al into water were studied, and the feasibility of using seed precipitation as a treatment technology of the leachate was discussed. The optimum condition of the process was determined as: alkali dross ratio 1.3, salt dross ratio 0.7, smelting temperature 500°C, smelting time 60min, leaching temperature 60°C, leaching time 30min, solid-liquid ratio 1:4. The results show that using the seed precipitation method, the leaching of aluminum reaches 92.71%, demonstrating the technique as a feasible and effective treatment technology of the leachate.

Jan 1, 2011

By Douglas Pollock, John Organiscak

Water spray characteristics, including droplet size and velocity, airborne dust capture potential, and induced airflow quantity for various spray nozzle designs were evaluated to provide basic information for improving spray applications. Water droplet size and velocity characteristics were initially measured by a Phase Doppler Particle Analyzer (PDPA) for hollow cone, full cone, flat fan, and air atomized spray nozzles at similar operating parameters. Airflow inducement and dust capture experiments were also conducted under the same operating parameters to examine any salient features of the spray nozzle type, droplet characteristics, induced airflow, and airborne dust capture. Test results indicate that there are trade offs between airflow inducement and dust capture efficiency. A spray nozzle with a wider discharge angle was observed to induce more airflow, but at reduced dust capture efficiencies. Increasing spray nozzle fluid pressure(s) generally reduced water droplet sizes with concurrent increases in droplet velocity, airflow inducement, and airborne dust capture. Placing a three-sided barrier around the spray nozzles normally reduced spray air induction and increased dust capture efficiency. A direct relationship between airborne dust capture efficiency and spray input power normalized per unit of airflow induced was ob- served. This information can be utilized to improve the performance of water sprays for reducing airborne dust levels.

By J. Boldy

Discovery of the Delbridge massive sulfide deposit in the Noranda district of Quebec resulted from an appreciation of the significance of a mercury leakage halo as a lithochemical pathfinder to blind ore. Its location, relative to a geologically inferred ore-bearing horizon within complex volcanic stratigraphy was also a factor. Systematic sampling of microfractures present in outcrops delineated a diagnostic anomaly, drawing attention to an area considered prospective for buried ore. The massive sulfide deposit was subsequently found to be blind and topped at the 110-m (360-ft) level.

Jan 1, 1985

By H. LeRoy Scharon

The electrical resistivity method was utilized at 245 road cuts and structure sites over the 166 miles of the Philadelphia and Western Extensions of the Pennsylvania Turnpike System. Varying geologic structures and rock types afforded an excellent academic study of the method as well as a practical application to modern highway engineering.

Jan 4, 1951

By M. Proulx

"RÉSUMÉ Le diagramme ternaire Al2O3-Sr-Y est un nouvel outil servant à l’exploration de gisements de sulfures massifs volcanogènes (SMV) archéens. Le diagramme permet de discriminer entre les roches volcaniques à minéralisations à zinc dominant (domaine Zn+) et celles à minéralisations à cuivre dominant (domaine Cu+), ainsi que les roches volcaniques ayant subi une chloritisation hydrothermale pouvant aboutir à la formation de chloritites associées aux cheminées d’altération (domaine Cl+). Ces trois domaines délimitent des zones d’influence géochimique ou d’empreintes hydrothermales résiduelles ou fossiles produites par les cellules de convection hydrothermales générées par des magmas. Le diagramme permet aux sociétés d’exploration de déterminer de façon peu coûteuse la fertilité potentielle des roches volcaniques archéennes en ayant recours à leurs bases de données et aux résultats de leurs analyses de terrain, sans aucune manipulation des données. Le diagramme ne s’applique pas aux SMV aurifères.ABSTRACT The tertiary diagram Al2O3-Sr-Y is a new tool to explore Archean volcanogenic massive sulphide (VMS) deposits. The diagram can be used to discriminate between the volcanic rocks where zinc is the dominant mineralization (Zn+ domain) and the rocks where copper is the dominant mineralization (Cu+ domain), as well as the volcanic rocks that were subjected to hydrothermal chloritization that could have led to the formation of chloritites associated with alteration chimneys (Cl+ domain). These three domains define the zones of geochemical influence, or residual or fossil hydrothermal footprints produced by hydrothermal convection cells generated by magmas. Exploration companies can apply the diagram to determine, at low cost, the potential fertility of the Archean volcanic rocks by using their databases and the results of their field analyses, without any data manipulation. The diagram does not apply to gold-bearing VMS deposits."

Jan 1, 2015

By R. H. Watson

A paper read by J. A. H. Church before the Northern Alberta Branch last February described a method of working thick inclined coal-seams from the dip upwards, with the view to preventing fire risk by using water for the stowage of waste workings, and extinguishing a conflagration should such break out, was favorably received; but there was some doubt as to the cost of such a method, as it involves a retreating system, which might prove too expensive for practical adoption. Let us consider a typical leasehold such as we are familiar with in the Rocky Mountains. The leasehold is crossed at one end by a mountain river, which is cut by the outcrop of a seam of coal, 30 feet in thickness, pitching as shown on the drawing herewith, which also shows the general line of the outcrop in elevation through the leasehold, which is two and a half miles long and contains 1,500 acres. The average lift is about 600 feet above river level and drilling has proved that the coalseam can be tapped at a depth of 1,500 feet, 2,000 feet down the pitch from the outcrop in the river, all as shown in the illustration, which is typical enough of our mountain conditions to serve the purposes of comparison of methods. We take up the leasehold and invest $30,000 to pay for drilling and prospecting; $30,000 more for the price of the lease to locator or holder, and say $100,000 to pay for a railway spur (it might cost twice this sum, but we are only comparing two methods in the same location) and "now we are ready to consider equipment and the cost of development.

Jan 1, 1924

By J. H. Westbrook

UNTIL very recently the development of high temperature alloys has been strictly empirical. It is, in fact, a great tribute to the intuition, perseverance, and industry of the practicing metallurgists of this country and abroad that the amazing increases in gas turbine service temperature over the past 15 years have been achieved with so little fundamental knowledge. The result of this development has been the realization of successful but highly complex alloys possessing five, six, or more alloying elements and correspondingly complex microstructures. Within the last few years, considerable effort has been devoted to the identification of the secondary phases in these alloys and to the correlation of the presence or absence of such phases with alloy properties. Little attention, however, has been given the problem of identification of the mechanism (s) by which such phases enhance the properties of the alloy and especially to the assessment of the particular properties of the secondary phase (either in- trinsic or relative to the matrix phase) which are basically responsible for the improvement. Conceivable mechanisms which might apply include dispersion hardening and precipitation hardening. In both cases geometrical factors—particle size, dispersion, volume fraction, etc.—and agglomeration re-

Jan 1, 1958

By Rudy Beltrán, Kellyn Cristobal

El presente trabajo muestra las mejoras realizadas en nuestras operaciones mineras, respecto a disminuir los accidentes que se han venido presentando en diversas minas a nivel nacional, relacionadas al uso de los calibradores para controlar el espesor del shotcrete (concreto lanzado), donde el personal se expone a la línea de fuego cuando el concreto aún se encuentra en proceso de fraguado para alcanzar las resistencias iniciales de sostenimiento. Ante esta problemática, se ha diseñado un mecanismo automatizado que se encuentra adaptado al equipo robot lanzador de concreto, el cual elimina la exposición del personal durante este proceso y ademas asegura la calidad del espesor de shotcrete aplicado en las labores mineras.

Sep 29, 2023

By R. O. Burt

The paper examines the role of gravity concentration in both an historical contest and within the modern mineral processing industry. It discusses the principles of the process on both a theoretical and practical level. The importance of ore mineralogy and its effect on the choice of the wide range of equipment available is discussed. The paper concludes with a discussion on the relative merits of gravity concentration to other forms of processing and seeks to answer the classical question - "Quo Vadis?"

Jan 1, 1982

By A M. Robertson, R Lefebvre

Air movement and associated oxygen transport through waste rock dumps has the potential to significantly enhance the rate of oxidation of pyrite-bearing material. While this is a desired outcome for most heap leach operations, airflow in waste rock storage facilities can result in significant increases in generation and acceleration of acid rock drainage. Hence, a good understanding of internal airflow through waste rock dumps is required to control ARD and minimise any associated liability. The principal mechanisms contributing to airflow and oxygen transport in a waste rock pile include: diffusion; advection due to a thermal gradient (chimney effect) and/or wind pressure gradients; and advection due to barometric pumping. While diffusion is typically limited to a near-surface zone of a few meters depth, advection and barometric pumping have the potential to move air (and oxygen) to much greater depths into the pile. In general, the more permeable the waste rock material, and the greater the height-to-width ratio of the waste rock pile, the greater is the potential for advective air movement. The reactivity of the waste rock material as well as the coarseness (hence air permeability), and the spatial variability of these properties within a pile, have a strong influence on the magnitude of thermally induced advection. In contrast, air movement due to barometric pumping is controlled by the waste rock porosity, changes in ambient air pressure and the heterogeneity of air permeability of the waste rock dump. Results of field monitoring and numerical modelling using TOUGH AMD are presented to illustrate the concepts on air movement in waste rock piles discussed in this paper. During the design and construction phase, airflow can be controlled by judicious placement of reactive waste rock and use of selective placement techniques to control the internal structure of the waste rock facility (eg introduction of horizontal layering, prevention of inclined, high-permeability, channels (æchimneysÆ)). Several closure measures are available to minimise airflow including: placement of a low-permeability cover to reduce air entry; and placement of a non-reactive cover material to isolate reactive material from the zone of active airflow and/or regrading of the waste rock pile to obtain a geometry and internal structure less susceptible to advective airflow.

Jan 1, 2003

By R Stefansen, T Wisdom, A Nicholson, K Rahal

The challenges of increasingly scarce water resources and the risk of dam failures has seen the mining industry turn to sustainable tailings management solutions such as dewatering and dry stacking. Filtering tailings has been seen in the past as a cost-prohibitive process for larger throughput mines. However, as larger pressure filters are developed, the economic case for filtered tailings has gained traction.Focus has largely been placed on the correct design and operation of the filters. It is critical, however, that the material handling portion of the disposal system is also properly designed and operated. Thorough testing at laboratory and pilot scale to determine the conveying properties of the filtered material needs to be conducted. This testing will insure the material handling system meets the important availability needs of the mine even during periods of variability in the upstream processes and mine plan.The control system must also be robust and flexible in design to compensate for this upstream process variability. The control system needs to allow for different flowsheets including straight filtered tails as well as EcoTails™, a low-energy solution for co-mingling waste rock and filter cake.This paper will present case studies of different material handling solutions, the testing required for them and the lessons learned from each.CITATION:Rahal, K, Nicholson, A, Stefansen, R and Wisdom, T, 2018. Material handling testing and control system requirements for dry stack tailings, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 361–368 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

SAG Mill Grinding Design Versus Geometallurgy - Getting it Right for Competent Ores Smarter processing for the future, in the area of SAG mill design involves accurate grinding test data, completing final mill design in less than three months, and at a cost of less than US$80 000. More detailed variability testing on the other hand takes longer, is more expensive, and is used for throughput optimisation for an existing or newly purchased mill. This paper shows that SAGDesignTM testing is excellent for new SAG plant design due to relatively low cost per test and the ability to do more testing for a limited budget on larger projects. It also briefly examines a way to develop proper geometallurgical ore hardness information on every block in the mine model, from the more detailed analysis data.

Sep 13, 2010

By T. R. Ellis

The author attempted to concurrently apply the US Uniform Standards of Professional Appraisal Practice (USPAP) and the Australian VALMIN Code to a complex mineral property appraisal assignment and previously to some modest assignments. This led the author into many severe difficulties. These difficulties included the high standards needed in the work of others and information and statements required from the client under the VALMIN Code. The exercises highlighted many positive features of both sets of standards. However, the author concluded that, without modification, VALMIN is incompatible with USPAP and the US regulatory environ¬ment. The author found that VALMIN violates US legal decisions regarding real property appraisal due to its requirement to include many items of business value. The US Securities and Exchange Commission's prohibition on reporting quantitative resource estimates proved to be a severe problem under VALMIN. Some VALMIN requirements could not be met due to the extent and quality of documents specified. Implications and thoughts regarding the development of a set of US minerals appraisal standards are discussed. Management considerations for complex mineral-property appraisal assignments are also presented.

Jan 1, 2000

By B. C. Haydon

Manganese silver ores are well known to be refractory towards cyanidation. Various processes have been suggested for improving the amenability of these ores. A sulfurous acid pre-leach is one such process. This paper traces the development and implementation of the sulfurous acid pre-leach process for the retreatment of manganese silver tailings at Tonopah, Nevada. An account of the test work program is presented, followed by a description of the operating plant and specimen metallurgical performance. The paper also summarizes the history of the Tonopah tailings, their mineralogy and makes reference to previous application of the sulfurous acid pre-leach process.

Jan 1, 1984

By G. P. Karmakar, K. K. Chandan

"The drilling mud is an essential part of the drilling process, which plays a major role in keeping safe and efficient oil and gas well drilling. In the oil industry, bentonite clay dissolved in water produces the simplest type of drilling muds. Bentonite clay contains montmorillonite particles. These particles are dispersed uniformly in water and such dispersions are used in various industrial products like paints, ceramics, pesticides and drilling muds. The bentonite clay easily dissolves in water and increases the viscosity of the water, which is one of the most important properties of a drilling mud. Bentonite has the highest swelling capacity, which is responsible for building up of the viscosity of the clay-water system. The flocculation behavior of bentonite is one of the major concerns for the performance of the water-based drilling mud in the oil and gas well drilling process. The behavior of drilling mud greatly depends upon the quality and quantity of bentonite clay, as well as the additives that are used in their formulations. In this work, a comprehensive study has been carried out to find out the effect of added polyacrylamide (PAM) polymer, surfactant, pH and salt concentrations on the dispersion/ flocculation characteristics of bentonite clay-water system. It has been observed that the increase in PAM dosage reduces the residual turbidity and improves the settling rate of the bentonite particles. The flocculation rate has also been found to be better under higher pH conditions. The combined effect of salt concentration and PAM dosage improved the overall flocculation efficiency of the system.INTRODUCTIONIn the oil industry, bentonite clay dissolved in water produces simplest type of drilling muds. Bentonite clay containes montmorillonite particles. These particles are dispersed uniformly in water. Such dispersions are used in various industrial products like paints, ceramics, pesticides and drilling muds (Akther et al., 2007). The bentonite clay easily hydrates in water and increases the viscosity of the mud system (Razi et al., 2013; Meng et al., 2012). Bentonite clay in the drilling mud increases the viscosity which is one of the most important prop erties of a drilling mud. Bentonite has the highest swelling capacity, which is responsible for the building up viscosity of the clay-water system (Sonmez et al., 2013). The drilling mud is an essential part of the drilling process, which plays a major role in keeping a safe and efficient oil or gas well drilling (ASME, S. S. C., 2005). The flocculation behavior of bentonite is one of the major concerns for the performance of the water-based drilling mud in the oil or gas well drilling process. This behavior of drilling muds greatly depend upon the quality and quantity of bentonite clay, as well as the additives that are used in their formulations (Yu and Amanullah, 2005; Akther et al., 2007). Bentonite particles form aggregate under certain conditions including high temperature, and high concentration (Luckham and Rossi, 1999). If the quality of bentonite is not sufficient to accomplish intended viscosity of the muds, it is essential to add certain additives to increase the viscosity and prevent aggregation of the system (Razi et al., 2013). The anionic polymer bearing sample can build up inter-particle bonds between the polymer and clay particles. The addition of various additives like, polymers control the dispersion and enhance the viscosity of the mud by controlling the flocculation of montmorillonite particles in bentonite dispersion (Heller and Keren, 2002; Mahto and Sharma, 2004)."

Jan 1, 2018

By X Zhang, Y Zhu, P E. Ngoepe, P P. Mkhonto, W Xiong, L Han, L Lu

The triazine molecules have not been given much attention and they are potential collectors that may positively impact the mineral processing industry. The adsorption of triazine as collectors such as sodium 2,6-dithio-4-butylamino-1,3,5-triazine (SDTBAT) on pyrite form a basis in design of flotation collectors that may be applicable in a wide range of sulfide minerals. The SDTBAT collector was compared with the sodium normal butyl xanthate (SNBX) and sodium normal butyl dithiocarbamate (SNBDTC). All collectors were adsorbed in their neutral form containing sodium on the pyrite (100) surface. The computational calculations found that the adsorption energies followed the order: SDTBAT (-300.35 kJ/mol) > SNBX (-186.10 kJ/mol) > SNBDTC (-163.78 kJ/mol). It was observed that the SNBX and SNBDTC adsorbed through the S atoms, while the SDTBAT adsorbed through the S atoms and N atoms onto Fe atoms. It is clear that the SDTBAT had a strong binding energy which is attributed to the presence of the triazine group that is electron depositing to the active S atoms compared to the SNBX which possessed the oxygen that is electron withdrawing. Moreover, the SDTBAT collector was found to bind stronger than the xanthate. This was complimented by microflotation tests that showed fast floating and higher recoveries of pyrite when using the SDTBAT collector than the xanthate and DTC. This clearly demonstrated that the SDTBAT is a potential collector to replace the xanthate collector due to its high selectivity and flotation power.

Aug 24, 2022

By Michael Hoch, Daniel B. Butrymowicz

The isothermal section of the Ta-Ti-Zr-0 system at 1500°C was investigated using X-ray diffraction and rrzetallographic techniques. Up to 71.4 at, pct 0 the system contains nine four -phase regions. Zsopleths at 10, 20, 30, 40, 50, and 60 at. pct 0 were constructed. The purpose of this investigation was to determine the general shape of the quaternary equilibrium phase diagram of tantalum, titanium, zirconium, and oxygen at 1500°C. The system was truncated at 66.7 at. pct 0 on the Ti-0 and Zr-0 binaries and at 71.4 at. pct 0 on the Ta-0 binary. The Ti-Zr-0 system was investigated in this laboratory.' The binary systems of interest have been compiled and discussed by Hansen and Anderk, chmidt, Hayes, Roberson, and asche, and Hoch and athur.' EQUIPMENT The Same equipment as that for the study of the Nb(Cb)-Ti-Zr-0 system was used.' The X-ray dif- fraction patterns were analyzed with the help of the ASTM card set7 and NBS circulars.' MATERIALS The tantalum powder (99 pct pure), the titanium powder (99.6 pct pure), the tantalum pentoxide, and the zirconium dioxide used in this study were purchased from the Fairmont Chemical Co., Newark, N.J. The zirconium powder (99.4 pct pure) was obtained from the Charles Hardy Co., Inc., New York. Reagent-grade titanium dioxide was purchased from the Matheson Co., Inc., Norwood, Ohio. The oxides were dried in air at 700°C for 24 hr before use. Though the materials used were not "hyper-pure", the impurities present do not affect the results (lattice parameters, phase boundaries), within the experimental accuracy. PROCEDURE The samples were heated by induction in a vacuum furnace, and examined metallographically and by X-ray diffraction at room temperature. The procedure was the same as that in the Nb(Cb)-Ti-Zr-O work,' EXPERIMENTAL RESULTS AND DISCUSSION OF DATA A four-component system can be represented by a tetrahedron at a single temperature and pressure

Jan 1, 1964

By J J. Cilliers, K Hadler

The potential of air rate profiling to significantly improve the flotation performance of a bank of cells has been shown by numerous studies. To date many profiles have been evaluated; balanced, increasing, decreasing and combinations of these. An increasing air rate profile, where the air rates are increased proportionally to each cell down the bank, has been typically found to yield improved flotation performance compared to other profiles. Air rate profiling has two distinct components; determining the correct total air rate for the bank, and determining the correct distribution of that air. This can be done simultaneously by finding the optimal air rate to each cell in the bank in turn through air recovery optimisation. Air recovery is the fraction of the inlet air which overflows the weir of a cell as unburst bubbles. The peak in air recovery (PAR) is a robust measurement of optimal performance for the operating conditions in the cell, and sets the PAR air rate. In this study, plant trials of different air rate profiles and profiling based on PAR, were evaluated. The total air rates to the bank for all profiles tested were approximately equal, allowing direct comparison. The highest cumulative mineral recovery was achieved by operating at the PAR air rates for each cell down the bank. Different distributions of the same total air rate to the bank gave the same cumulative upgrade ratio, but lower cumulative recoveries. In this work the upgrade ratio is defined as the ratio of the concentrate grade to the feed grade. The increase in cumulative mineral recovery, at the same upgrade ratio, in this study was greater than 33 per cent. Air recovery based optimisation of air rates to banks of cells significantly improves flotation performance as it simultaneously determines the optimal air rate to the bank, and the optimal distribution of that air.

Jan 1, 2009