Search Documents

By J. -P. Tshibangu, M. Ramos da Silva, F. Descamps, C. Schroeder, J. -C. Verbrugge

"The mechanical behaviour of rock materials is largely influenced by the stress state and pore pressure; this needs to be considered in many applications, such as petroleum engineering, tunnelling or stability of underground excavations.Conventional triaxial tests (d2 = d 3) are generally used to assess the influence of confining and pore pressure. In this work, those tests are performed on a porous rock named Sorcy limestone, along with more advanced stress paths like triaxial extension (d 2 = d 1) and purely deviatoric tests with independent pore pressure control. Those tests are combined to a true triaxial study on the dry rock in order to investigate the effect of true triaxial stresses and, hence, build three-dimensional limiting envelopes accounting for the influence of pore pressure.Three-dimensional limiting envelopes of dry Sorcy limestone are built in meridian and octahedral planes. The shape of the octahedral sections changes with the mean stress from triangular to hexagonal and then quasi circular. At even higher mean stresses, the evolution continues towards a triangle with apexes oriented in the direction of triaxial extension stress states. In meridian sections, the deviatoric stress first increases with the mean stress. The transition between this deviatoric mechanism and the cap surface occurs at different mean pressures depending on the Lode angle.Terzaghi’s effective stress is found to govern the yield and plastic behaviour of saturated Sorcy limestone. Triaxial tests show that the limiting envelope does not depend on the loading path (conventional compression and purely deviatoric stress paths). In triaxial extension, the brittle-ductile transition is observed for a higher mean pressure than in triaxial compression, as previously found for true triaxial tests on the dry rock.Finally, it is shown that upon appropriate normalisation, the dry and saturated yield envelopes come very close one to each other. This suggests that only the size of the yield envelope changes between dry and saturated state (pore pressure = 5 MPa); its shape does not seem to evolve."

Jan 1, 2015

By U. E. Paakkinen

Progress in computer control of flotation circuits has developed parallel with advances in reliability of on-stream X-ray analysis (Cooper, 1976). Attainment of acceptable results with X-ray fluorescence analysis over the past ten years has led to application of computer control in more than 30 concentrators. Gains in applying flotation control also have given incentive to improving measurement and control devices for other essential functions in control systems. At the same time, advancing technology has made available computer systems having characteristics practical and economical for the physical environments of concentrators and ore processing plants. Benefits from flotation control have centered on increased efficiency in mineral separations, derived by stabilizing circuit operation subject to changing ore characteristics. The gains have been most evident in processing complex ores for multiple concentrate products. In many cases, particularly when coupled with grinding control, the economic results from on-line control have been substantial compared to investments in monitoring and control equipment.

Jan 1, 1979

By V. Svalbonas

The process of grinding mill quality assurance brings with it associated truths and myths. When the mill quality assurance process took its first great steps forward in the late 1970s and early 1980s, they were in response to the conditions existing, in our industry, at those times. In the late 1990s, we are faced with different conditions, and problems, and need fresh solutions. Yet the system developed for the early 1980s has produced no new approaches for the late 1990s, becoming instead more hardened and entrenched. This lack of development and actual resistance to research is now costing the industry significant amounts of money in late start-ups and useless scrap loss.

Jan 1, 1999

By A. G. Merma

In this work, the electrocoagulation technique was studied in order to treat chemically stabilized concentrated oil-water emulsions. This study was mainly focused on the effects of operating parameters such as initial pH, current density, reaction time, electrode distance and inlet concentration on the separation of oil as measured by the chemical oxygen demand -1(COD) method. The synthetic emulsion was prepared from Shell - Talpa 30 oil (3g.L-1) and sodium dodecyl sulfate (1.0 g.L), having a Zeta potential around -70 mv at pH 8.7. The process was carried out in an electrocoagulation cell with a set of four parallel monopolar electrodes. This set consisted of two aluminum plate anodes and two 316L stainless steel plate cathodes. Kinetic curves showed that the electrocoagulation process exhibits three phases: (1) an initial phase, where the COD did not decrease because the solution had not reached the minimum amount of dissolved aluminum required to cause the break-up of the emulsion, (2) a reactive phase during which COD decreased due to possible agglomeration of the precipitates and (3) a steady-state phase where the COD did not change. The results showed that the period to reach the reactive phase decreased as the current density increased and the pH values decreased.

Jan 1, 2009

By M. Polat, S. Chander

Many models have been suggested in the past to obtain a satisfactory fit to flotation data. Of these, first-order kinetics models with a distribution of flotation rate constants are most common. A serious limitation of these models is that type of the distribution must be pre-supposed. Methods to overcome this limitation are discussed and a procedure is suggested for estimating the 'actual' distribution of flotation rate constants. It is demonstrated that the classical first-order model fits the data well when applied to coal flotation in narrow size-specific gravity intervals. When applied to material which is fractionated on the basis of size alone, the use of three parameter models, which were modified from their two parameter analogs such as rectangular, sinusoidal, and triangular, gave most reliable results.

Jan 1, 1995

INTRODUCTION IT is 10. years this summer since the first of the contributions which it has been my privilege to make to the working tools of the hydrometallurgist was set at work, but a full description of what has come to be known as "Dorr Machinery" has never been published in the Transactions of the Institute, and it has been suggested to me that an account of the same would prove of interest to members, although most of those engaged in cyaniding and concentration are probably familiar with it. The account which I shall give of the development of the machines must be recognized as being written from the viewpoint mainly of my own local experience and not from that of one who was familiar with the general metallurgical practice throughout the world. Most advances in any art are conceived before the time is ripe for their development and any .invention which comes into general use will usually be found to have been tried out in a crude way and abandoned more than once. If the early experimenter went as far as the Patent Office, his work may serve no other purpose than to prevent the issuance of the broadest patent to those who later may develop a commercial process. The cyanide process in the United States early in 1904 was mainly confined to the leaching of dry crushed ores, both coarse and fine, and sand treatment of tailings from concentration and amalgamation. In the Black' hills some plants were crushing in cyanide solution, leaching sands and handling the slime by the well-known decantation process. Filter pressing, in use for some years in Australia,had been tried in several places in this country and the Moors process had been abandoned at Mercur after' a short run, but was doing good work at the mill of Lindbergh, Dorr & Wilson, at Terry, and being installed at Bodie and the Liberty Bell. A general feeling, however, still existed that, slimes were to be avoided when possible, on account of the losses in treatment and the difficulty of making a good leaching product when they were present in large amounts, especially when the crushing was done in cyanide solution.

Jan 8, 1914

By C. H. Mathewson

COPPER and the copper-base solid solutions readily form twin crystals when plastically deformed at a suitably elevated temperature or annealed after cold deformation. In fact, no feature of the microstructure of these materials is more prominent or characteristic than these straight-sided bands or simple lines of division which sometimes come from groups of thin polysynthetic lamellae, penetrating part way or wholly through the parent grain substance, but often divide the grain into a few or perhaps only two crystallographically related parts. Nearly always the bands as seen in the usual microscopic examination of a specimen come into vivid contrast with the adjacent crystalline material owing to the inherent difference in orientation. Bands which under special conditions of orientation cannot be seen with vertically incident light are often visible under oblique illumination and, when this fails, contrasting effects usually may be obtained by using polarized light. There is no longer any doubt that these synthetic banded structures obtained in the ordinary course of working and annealing are due to twinning of the spinel type which was observed long ago in a number of metals crystallizing in the isometric system.1 It has been customary in metallurgical literature to designate these synthetic twins, which grow into prominence during an annealing process, as "annealing twins" without regard to the actual mode of their formation, which is, indeed, obscure and with scant recognition of the fact that prior deformation is essential, no twins having been observed in metal of known unstrained history. This is questionable; especially in view of. the fact that in a number of metals and minerals, reorientation into the twin configuration is known to occur as a result of a simple shearing mechanism along the recognized twinning planes and the

Jan 1, 1930

By H. Wesley Peirce

Arizona, in 1966, has continued to be the site of an extensive and intensive search for metallic mineral deposits. Over fifty separate entities--companies and individuals--have been actively engaged in mineral exploration programs, both large and small, in the Basin-and-Range portion of the State. Certainly, copper has been primarily responsible for the major efforts, although associated gold, silver, and molybdenum mineralization also has been important in the economic evaluation of potential copper deposits. It is not difficult to explain why the Basin-Range portion of Arizona is receiving such attention. Part of the story, undoubtedly familiar to most, can be illustrated by reference to three graphical presentations. For example, Figure 1 shows Arizona's annual copper production for the period 1955-1965, inclusive, and it demonstrates that new records of production have been accomplished in each of the past 6 years and in 9 of the last 11 years.

Jan 1, 1967

By Joseph E. Matta

The Bureau of Mines conducted tests using a tracer-gas technique to measure the effectiveness of the jet fan, which is often employed in mines to ventilate dead headings. Results of these tests show that jet fans can (1) ventilate dead headings beyond the maximum penetration distance indicated by smoke-tube detection of air movement, and (2) redistribute available fresh air through larger working areas. However, if the fresh air base is insufficient, the fan will merely recirculate the contaminated air and disperse it over a larger volume.

Jan 1, 1978

By Jr. Robison

"Aluminothermic (""thermite"") smelting became commercial with the development of tonnage aluminum, and prospered producing metals and alloys with higher cleanliness, consistency and elemental control than competing technologies. We explore the scope of thermite smelting, and metallothermic smelting in general; the thermochemistry of the process; and its advantages and limitations as applied to industrial production. We review currently-produced products of thermite smelting in several forms and a wide range of heat sizes. As these products serve several industries, we relate the demands of those industries to the requirements imposed on the thermite process, leading to process dynamics and mechanisms to control/alter those dynamics. We review ways to lower the process costs by altering process stoichiometry, using other energy sources and utilizing less costly materials while considering effects on product quality and customer requirements. Finally, we examine overall emissions control and waste disposal.IntroductionAluminothermic smelting is the reduction of various oxides by aluminum to produce metals or alloys with varying levels of residual aluminum. One of the earliest uses of the process was the production of liquid iron to weld railroad rails, later modified in ""thermite grenades"" used to ""spike"" artillery pieces in World War II. Then during the 50's, 60's and 70's the growth of jet aircraft created a demand for new superalloys and titanium alloys, both requiring master alloys for efficient production. Aluminothermic smelting grew with the aerospace industry and with the expansion of microalloyed steels. It is very much a niche industry, dependent on the specialized demands of the specialty steel, superalloy and titanium industries. In this paper we introduce the characteristics of aluminothermic smelting, the scope of smelting operations, the markets served, and the environmental aspects of the process, as seen through the eyes of a company using aluminothermic smelting for over fifty years"

Jan 1, 2012

By J. E. Crawshaw

"The few previous observations of the effect of turbulence on limits of inflammability have been made on a small scale in turbulence produced either by a fan or by movement of the mixture.By a suitable amount of turbulence from a fan the lower limit of methane was 5 per cent as compared with 5 per cent observed for quiescent mixtures in the same vessel.3 With a streaming movement of the gas mixture within the range of speed from 35 to 65 centimeters per second (69 to 128 feet a minute) the lower limit was approximately 5 percent,4 For a quiescent mixture of ethane the lower limit was 3.10 per cent ethane, but with fan running at a moderate speed a 3 per cent mixture exploded.5The object of the tests herein reported was (1) to determine the lower limit of natural gas in a mixture of natural gas and air Which would be ignited and propagate violently when the turbulence was produced by explosives fired from a cannon into the mixture; (2) to observe the behavior when the mixture contained less than this low limit; and (3) to determine how turbulence produced by a fan affects thin limit.Four series of tests were run, three of which were to determine the effect of different sources of ignition: Tests with (1) an electric igniter; (2) 3F black blasting powder stemmed with 2 pounds of dry fire clay stemming used to ignite the mixture, and (3) 40 per cent straight nitroglycerin dynamite unstemmed. The fourth was made to study the effect of turbulence produced by a two-speed electric fan, using an electric igniter as the source of ignition.In both series of tests with explosives, charges of 50 and 200 were used to determine the effect of increased quantity of explosives on the lower limit of natural gas."

Jul 1, 1930

By Sandra Penttinen

To assist blasting professionals with the creation, documentation, and appropriate methodology to standardize the data collection of the pre and post blast investigation process. Penttinen Associates will present a logical non-technical presentation focusing on: Why pre-blast surveys SAVE How to prepare for pre-blast inspections What to do in preparation of pre-blast inspections The creation of an industry standard all-inclusive pre-blast document Establishing pre-blast inspection operational standards Preserving the data.

Jan 1, 2001

By Jean-Luc Collins

"This paper shows how simple reliability concepts such as mean time between failures and mean repair time can be used efficiently to help increase equipment availability and so reduce the economic losses associated with unreliability.More specifically, the paper shows how these simple concepts can be used in maintaining an appropriate balance between fleet failure and repair rates and how they can be used for setting up priority repair rules f or queuing equipment.IntroductionA profitable mining operation must handle large quantities of ore and waste at the lowest possible cost. To achieve this objective, the operation must optimize the productivity of its fleets of equipment by efficient management of the time element. Figure I shows some basic equipment activities in an open pit operation while Figure 2 shows a tree diagram describing some time elements of these activities.It should be noted that the only time a piece of equipment can generate a profit is when it can be found in the operating status. In order to maximize this time element, the sum of the other time elements must be minimized because the total time is always fixed.This paper shows the application of simple techniques capable of reducing the waiting time for repair (maintenance delay) by using simple reliability concepts."

Jan 1, 1988

By D. M. Mubita

Dilution reduction is one of the areas that offer metal mines an opportunity to increase revenue and reduce costs, resulting in enhanced profits. Effective dilution control programmes require interaction on a multi-disciplinary level. This paper outlines recent initiatives undertaken at Konkola Mine to reduce dilution and increase revenue. The increase in revenue arising from reduced dilution and high factors between in situ and delivered to mill grades were quantified and amount to close to U$ 1.0 million per one per cent improvement in grade factor at a 75c/lb copper price. Sources of dilution from open and in?stope mining methods practised at the mine were identified and a multi-disciplinary dilution control forum set up to control these. Among the major achievements were the introduction of low dilution in-stope mining methods; the introduction of Gemcom geological and mining planning software to replace traditional pencil and paper methods, leading to better in situ estimation and production planning; enhanced control in open stopes through dilution awareness among mining production personnel; location of critical secondary development ends in correct positions; enhanced blast hole control; tracking of development waste by metal tracers and monthly tally; implementation of a cavity monitoring system to check over-breaks in open stopes; and setting up of a stope history database. The results from the cavity monitoring system showed that stopes with over-breaks of 5 metres or less could be controlled to break along the hangingwall contact.

Jan 1, 2005

By T. A. Grammatikopoulos, B. Vasily, A. H. Clark

"The St. Lawrence deposit is a large wollastonite skarn (ca. 9 Mt @ 41.3% wollastonite) adjoining the gabbroic-to-syenitic Leo Lake pluton in the granulite facies Frontenac Terrane of the Grenvillian Central Metasedimentary Belt. It occurs within a horseshoeshaped horizon of quartzite, open to the east. The skarn extends over 1.2 km2, and comprises wollastonite-dominant, wollastonite-clinopyroxene, and diverse quartz-feldspar-sulphide (-titanite) layers, interbanded with, and strongly folded within, the quartzite. As in the world-class wollastonite deposits of the Willsboro district, New York, no carbonate protolith is preserved, and calcite is a negligible constituent of the mineralized zones. Wollastonite development is nonetheless ascribed to metasomatism of a metacarbonate unit by magmatogene, silica-rich, CO2-poor (XCO2 < 0.05) fluids, at P = 350 MPa and ca. 560°C, or, alternatively, 550 MPa and ca. 630°C.Several high-grade zones, averaging >40% but locally exceeding 80%, of translucent, white, tabular wollastonite grains, with lengths of 0.2 cm to 5 cm, have been delimited by drilling. Preliminary beneficiation studies yield high aspect-ratio and high-purity (low Fe and Mn) concentrates.St. Lawrence compares favourably to other known prospects and operating wollastonite deposits: having good chemical and physical properties, low iron content, and high aspect ratios (>20:1). In addition, the deposit has a favourable size and location, and will benefit from a low Canadian dollar. Canada currently has no wollastonite production."

Jan 1, 2003

By M. L. Gupta, S. P. Banerjee, D. C. Panigrahi

The paper describes the computer simulation of climatic conditions in the longwall workings in India. For this simulation work the longwall panels have been divided into two segments, viz; the intake gate segment and face segment. Two computer models, one based upon transient heat and moisture transfer algorithm of McPherson (1986) and the other on quasi-steady algorithm of Starfield and Bleloch (1983), have been developed for intake gate segments. Similarly two computer models, one based upon the transient heat flow in cylindrical tunnel with certain modifications of McPherson algorithm (1986) and the other on linear heat flow concept, have been developed for face segment. The models incorporate the necessary running and spot heat sources present in their respective segments. In addition to this the goaf heat flow parameters have been incorporated in the models for the face segments. Continuous recording of important thermal parameters have been carried out in several longwall faces in India to validate these models and the results have been presented.

Jan 1, 1993

By Mike Turner

The Otter-Juan mine was closed by WMC Resources? Kambalda Nickel Operations (WMC-KNO) in 1999 due to the combined effects of low Nickel prices and high mining costs. GBF Mining Pty Ltd purchased Otter-Juan Mine from WMC in early 2001 as part of WMC?s disinvestment from the nickel mines in the Kambalda area. Goldfields Mine Management (GMM), (a wholly owned subsidiary of GBF Pty Ltd) re-opened Otter-Juan in May 2001. The Otter-Juan mine is one of the oldest mines in the Kambalda region and is now mining at depths below 1160mbs. Stresses are very high, rock mass deformation considerable, and the mine has a history of serious seismic activity. Orebody widths in the current mining area range from 2 to 2.5m, with dips from 25° to 40°. On taking over the operation, GMM converted the mining method from the previous mechanised drift and fill method to a slot-rise and strip method using hand held airlegs. During the latter years of production under the control of WMC, production averaged around 12000 tonnes per month, with grades of 2.7% and orebody extraction of only 55 to 60%. In the last three years of operation under the control of GMM the mine has produced an average of 12000 tonnes per month of ore at an average grade of 4.2% and with an orebody extraction of 70 to 75%. The mine is now highly profitable with at least another 3 years of reserves remaining at depth. The main benefits of the current method include reduced dilution and increased extraction. In the relatively poor ground conditions experienced this has only been possible using airleg mining, with excavations designed to suit conditions, support to suit rockmass deformations, and with improved extraction sequencing. Other benefits have included improved operating conditions, reduced falls of ground incidents and a dramatic reduction in seismic activity. These achievements have only been possible by stepping back in time and using traditional airleg stoping methods to extract the maximum amount of the orebody with minimum dilution. This paper includes details of the mine history, geology, mining method, seismicity, and support.

May 1, 2004

By Junji Shibata

Waste solution from the Ni non-electric plating process contains 4.0 kg/m3 Ni, 0.1 kglm3 Fe, 0.0 I kg/m3 Zn, 48 kg/m3 S042-, 98 kg/m3 HP032-and 31 kg/m3 laetic acid as a typical composition. Solvent extraction, cementation, ion exchange resin and precipitation methods are possible to use for the treatment of this kind of solution. In this study, solvent extraction of Ni was investigated using two kinds of extractants to clarify the relation between extraction percent and pH for various extractant mixtures. As Ni ion has an octahedral structure with ligands, the synergistic effect for Ni extraction is considered to take place in solvent extraction using two types of extractants. The investigation of the synergistic effect for Ni extraction was carried out in case of various extractant systems.

Jan 1, 2003

By Francisco Zenteno

Dado que la operación aurífera de Pierina representa uno de los costos operativos más competitivos del mundo, la minera Barrick Misquichilca trata de proporcionar un grato ambiente de trabajo para su personal, estimulando la creatividad y la polifuncionalidad en sus empleados. Por ello, nace el proyecto SIP2000 donde optimiza el sistema de información para el mantenimiento preventivo de la planta de procesos en la mina Pierina. El proyecto comprende el desarrollo de tres fases: La primera fase comprende la definición de los principales equipos críticos que podrían afectar a la producción, asímismo la implementación y estandarización de redes de comunicación entre equipos críticos para finalmente desarrollar interfaces HMI que supervisen variables relativas a Mantenimiento. La segunda fase, integra todos los sistemas de supervisión y control de planta con los sistemas de seguimiento “online” de Mantenimiento (fase 1), desarrollando un solo sistema de tratamiento y análisis de información de planta; y la tercera fase comprende la instalación y el desarrollo de aplicaciones basadas en tecnologías Cliente/Servidor con base SQL, que finalmente proporcionan la información y los medios para realizar consultas que optimizan el seguimiento y toma de decisiones relacionado al mantenimiento preventivo/predictivo.

Jul 17, 2000

By Charles J. McMahon

In a recent paper, Floreen and Hayden report that additions of the noble metals iridium, rhodium, ruthenium, and platinum to Fe-C alloys containing 0.03 to 0.08 wt pct C act to significantly reduce the ductile-to-brittle transition temperature in a notched-bar impact test. They compare these results with the similar, well-known effects of nickel and manganese additions, and they note that this supports the hypothesis that addition of austenite stabilizers enhances notch toughness. Although not attempting to offer an explanation for this, they suggest that it might be found in an alteration of the bonding characteristics of the bcc lattice of iron by additions of elements which tend to stabilize the fcc lattice. While this suggestion appears to have some merit, it should perhaps be held in abeyance until two more likely possibilities have been explored. It is now fairly clear that the beneficial effect of manganese derives from its ability to promote a globular carbide morphology instead of the platelike form found in grain boundaries and pearlite patches in Fe-C al10~s.&apos; Previous work14 has also shown that cleavage fracture in Fe-C alloys of the type tested by Floreen and Hayden originates almost exclusively in the cracking of cementite platelets, and that the ductile-brittle transition temperature is very sensitive to the volume density and size of these carbides. Treatments which lead to development of nonlamellar carbides or fine dispersions of carbides, such as quenching and tempering or appropriate alloy additions, promote toughness by removing the primary mode of cleavage initiation. The effectiveness of manganese in this regard has long been known. Nickel appears to behave in a similar manner, though the effect is perhaps not as dramatic as with manganese.15 However, nickel additions do lead to a definite refinement of ferrite grain size following a given transformation heat treatment, and this in itself acts to greatly enhance notch toughness.&apos;&apos; (The grain sizes of the various heats tested by Floreen and Hayden were not reported, so it is not known how much influence this factor exerted in their results.) In conclusion, it is suggested that one should consider the well-established effects of alloying elements on carbide morphology and ferrite grain size before resorting to more complex possibilities, such as modification of interatomic bonding.

Jan 1, 1969