Search Documents

By H S. Mitri, A Sainoki

Destress blasting techniques have been widely employed in underground mines for the purpose of preconditioning highly stressed rock mass. Appropriate applications of the technique successfully contribute to increasing mine safety (eg mitigating the risks for rock bursts). This paper presents a simulation technique to estimate the extent of damage zones induced by destress blasting. A 3D numerical model with a single blasthole is constructed with FLAC3D code, whereby static analysis is carried out in which horizontal and vertical stresses are applied to the model in order to simulate stress conditions in a deep underground mine. Afterwards, dynamic analysis is performed whilst applying time-varying blast pressure along the blasthole. The blast pressure profile takes into consideration an instantaneous increase and gradual decrease in blast pressure as well as the propagation of detonation along the blasthole. In this paper, constitutive models allowing for shear and tensile strengths of rock mass that are dependent upon strain rate are newly implemented into FLAC3D code with C++ programming language, whereby blast-induced damage is assessed by the extent of tensile and shear failure zones. The results obtained from the dynamic analysis show significant decrease in the extent of yielding zones induced by destress blasting with increasing the magnitude of in situ stress. They indicate that considering in situ stress state is indispensable in order to propose proper blast design for each level in underground mines. Based on these results, the relationship between the extent of the damage zone and depth at which destress blasting is performed is established. Furthermore, stress dissipation induced by destress blasting is examined with static analyses, in which the modulus of elasticity is decreased according to a rock fragmentation factor, a, only for the area where tensile and shear failures takes place during the dynamic analyses. A model parametrical study with respect to a is undertaken. The relationship between the rock fragmentation factor and the stress dissipation in the yielding zones is developed from the parametrical study. The developed relationship can be useful when destress blasting is designed for massive rock masses.CITATION:Sainoki, A and Mitri, H S, 2015. Simulation of damage zones induced by destress blasting, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 245–256 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By S. G. Luckey, N. R. Harrison, F. Nadeau, U. Brüx

"The adoption of tailored-rolled or tailor-welded blanks (i.e. TRB/TWB) in the automotive industry has been known to offer great potential for the optimization of weight, function, cost and complexity. Vehicle light weighting can further be achieved by using high strength aluminum alloys like the 7xxx-series. 7xxx-series alloys are capable of delivering specific strengths equal to or greater than high strength steels. However, room temperature formability of this aluminum class is limited, so one approach to forming 7xxx-series alloys is by hot stamping. Hot stamping utilizes an elevated temperature blank and the high pressure stamping contact of the forming die to simultaneously quench and form the sheet. This paper explores the initial feasibility of tailored thickness material for body-in-white applications when processed under hot stamping conditions.INTRODUCTION Steel tailor-rolled blanks (TRB) or tailor-welded blanks (TWB) have been used within the automotive industry as a method of reducing weight, expanding material utilization, and decreasing overall part/assembly cost (Ganeasan et al., 2015; Merklein et al., 2014; Hirt et al., 2005; Kridli et al., 2000). The production of such tailored thickness materials has resulted in over $2.5 billion (2016) in combined industry sales (Mubea, 2018). As automakers begin to adopt the manufacturing practices traditionally reserved for steel such as tailor rolling/welding with greater enthusiasm for vehicle light weighting, there exist an opportunity to expand the material database to extend beyond the traditional aluminum alloys found in current production. High strength aluminum alloys, i.e. 7xxx-series, are ideal for structural automotive applications due to their high specific strength; however, they have limited room temperature formability. Hot stamping, another manufacturing practice used by the steel industry, can be used to form these high strength materials. The combination of tailoring the thickness of a sheet material and hot stamping provides an opportunity for significant weight saving within an existing manufacturing footprint. This paper explores the potential and challenges of this approach when applied to structural body-in-white components. The methods for tailor rolling, tailor welding and hot stamping are described and applied to the production of a 7075 aluminum alloy B-pillar. The results are discussed in terms of feasibility and weight savings."

Jan 1, 2018

By R. R. Wells

An important activity of the Bureau of Mines is the continual search for new sources of minerals. As a part of the investigation of strategic mineral deposits in the United States, samples of mercury ores were submitted to the Ore Dressing sections of the Salt Lake City and Albany stations for metallurgical testing. This paper gives data summarizing the results obtained from laboratory beneficiation studies of mercury ore samples submitted during the period 1941 to 1947. Ores tested included three from Jackson County, Oreg., one from Valley County, Idaho, one from Storey County, Nev., and one from Sonoma County, Calif. In general, the ores from Oregon were not amenable to concentration by flotation because of intimate association of cinnabar with other minerals or because of extremely low grade. One Oregon ore was amenable to direct distillation provided lime was added to reduce corrosion of the retort.

Jan 1, 1950

By D Kay, M Lovitt

Mass Blasts are generally required at the completion of longhole stoping cycles to maximise the recovery of ore from a specific orebody. During the course of mining, the practice is to leave pillars of ore to support the opening left by extracted ore and to mitigate stresses from working areas of the stope. These pillars usually contain ore that has been included in the resource evaluation and is highly valuable to the mining operation. Due to their stressed nature, the removal of pillars by conventional blasting techniques, through small blasts, can result in pillars being reduced beyond their critical size and ultimately failing, rendering the ore unrecoverable. The AurionGold Kanowna Belle Gold Mine operates a Mine to Mill philosophy. This philosopy requires the fine tuning of blasting to provide the best possibe ore feed at the highest grade for mill productivity. This means that ore to the mill must be well fragmented from blasting that provides high extraction rates from draw points, with minimal dilution from overbreak or fall off, and sized to maximise SAG mill throughput. The AT04 Mass Blast contained significant ore reserves which were required to meet gold production targets. KBGB needed the AT04 Mass Blast to perform as well as if not better than conventional stope blasts to maintain mill production. This paper describes the circumstances, planning philosophy, techniques, including the use of Electronic Initiation Systems and Bulk Emulsion Explosives, and results that provided a highly successful outcome.

Jan 1, 2002

By M. Turek

Cost management in the conditions of increasing competition and unforeseen market turbulence constitutes one of the key areas of the enterprise?s activity. In the last two years the demand for hard coal on the domestic and global market of non-renewable resources has increased significantly. Polish hard coal mining industry, as an industry in the stage of decline, received a chance for rejuvenation. However, one of the most significant conditions of seizing this opportunity is the rationalization of mining costs and improvement of production effectiveness. Due to the significance of this issue, the main objective of the paper is to identify the possibilities of improving the production effectiveness in the hard coal mining industry. In order to meet such an objective, in the first part of the paper we measured effectiveness in the Polish hard coal mines in years 2006- 2011. The research encompassed three out of five mining enterprises operating in the country. Then based on the received results, guidelines concerning the improvement of effectiveness of production were created, taking into consideration infrastructural, technical, economic and organizational determinants. Furthermore, opportunities and threats for improving the production effectiveness, stemming from the external conditions have also been indicated.

Aug 1, 2013

By Gary P. Sames

The Bureau of Mines recently initiated a study of geologic features that contribute to roof instability in western U.S. underground coal mines. The purpose of the study is to provide information for use in ground control planning and safety hazard reduction in that region, where mining activity has been increasing. Hazardous geologic conditions were surveyed in selected underground coal mines in Utah and Colorado, and both depositional and structural features were identified as potential ground hazards. Although the conditions found do not differ in kind from hazardous geologic conditions in the Eastern United States, they do differ in intensity of occurrence and relative importance. Three depositional features dominate where unstable roof occurs in western underground coal mines: paleochannel deposits, crevasse splay deposits, and flood basin deposits. Three structural features identified as hazardous, but not so widespread or common as the depositional hazards, are faulting, jointing, and igneous intrusions. This survey establishes a foundation for future studies aimed at reducing and preventing ground control accidents in western coal mines.

Jan 1, 1988

By C. Flores

The most common experimental approach of studying one variable at a time while holding all others constant is extremely inefficient. Use of statistical methods enables engineers and scientists to obtain meaningful information with the fewest experiments, reducing cost and wasted effort. In particular, the Taguchi method can be more efficient than traditional full factorial experiment designs, as it can study more variables with fewer nuts, and it is more robust against process "noise." Taguchi designs are also simple to formulate and the results can be analyzed by simple PC spreadsheets. The role and benefits of using the Taguchi method in experiments to develop and optimize processes is discussed.

Jan 1, 1998

By AMIT SHARMA, BIBHUTI BHUSAN MANDAL

Operators of mining vehicles are exposed to high levels of whole-body vibration (WBV) and are therefore at risk of developing vibration-related health disorders. For implementing an effective control strategy, it is imperative to locate the source(s) of vibration, and the specific changes that might occur to the vibration signals during its transmission through the seats to the recipient human body. With this objective, Seat Effective Amplitude Transmissibility (SEAT) values of seat modules used in dumpers (n = 10) and other heavy earth-moving machines (n = 11) were evaluated in an iron ore mine. Vibration was measured simultaneously on the seat and on the cabin floor beneath the seat using tri-axial and uni-axial accelerometers. The study aims at determining the quality of seat modules of the transport and non-transport vehicles from the perspective of their natural resonance frequencies and capability of any such seat in reducing harmful vibration. The highest acceleration values were observed in the z-axis for all the dumpers. SEATrms values ranged from 78 to 133% and SEATvdv values ranged from 72 to 130% for the dumpers. For other HEMMs, SEATrms values ranged from 55 to 125% and SEATvdv values ranged from 56 to 123%. Mechanical vibration contains multiple frequency components. To understand the changes taking place to the different signals at these frequencies, 1/3 octave band analysis was carried out for the signals recorded both on the seat and the floor. There was significant attenuation (38 to 57%) at 4 Hz for three Dumper seats, whereas they resonated in the range of 1.6–2.5 Hz. The transmissibility(%) in the resonating frequencies ranged from 108 to 156%. Resonance frequencies for the remaining seven dumpers ranged from 3 to 8 Hz. The spine has been reported to resonate at 4 Hz, whereas resonance at 1.6 Hz has little significance to human beings in regard to WBV of a seated person. Hence, the characteristic resonant frequency of 4 Hz of seats as observed in the present study has the potential of causing adverse impacts on spinal health. Evaluation of SEAT factors and resonance characteristics of seats are therefore recommended to be examined while selecting a mining vehicle for regular deployment in mines.

Mar 12, 2021

By Thomas A. Gray

The Dolph Mine fire site is located in Lackawanna County, PA, approximately three miles northeast of the city of Scranton. The fire was burning in both coal refuse (culm) and underground anthracite mine workings. It was reportedly begun by rubbish burning on top of a culm bank. A site investigation was completed in 2006 to define the extent of the fire and to recommend fire control measures. A cut off trench was selected as the principal control method. Plans and specifications were prepared in late 2006. The project was bid and a contractor selected in early 2007. The trench construction was completed in 2007. This paper describes the investigation and selection of the fire control method and discusses the trench construction.

Jan 1, 2009

By Henry M. Harris, Hal J. Kelly

Electrical dewatering tests are described in which the laboratory cells were designed for continuous operation using an endless metal belt as the anode . The test slurries were dilute , containing from 2.5 to 14.4 percent solids (specific gravity of 1.02 to 1.10 ) that were all minus 8 microns in size . Recovery of the solids of low water content was the practical objective of the investigation . Process variables evaluated and reported are : The effect of feed rate , amount of electrolyte , samples from different sources , and the use of two cells in series . These variables are evaluated on the basis of yield of clay per kilowatt - hour , recovery , and the amount of solids in the deposited clay . Recovery , yield , and solid content of the belt anode product are interdependent , and changes that will improve one of these characteristics often are accomplished at the expense of the others . Tests in which recoveries range from 50 to 60 percent usually result in yields of 8 to 9 kilograms (kg ) of dry clay per kilowatt- hour (kwhr ) . Under these conditions , the solid content of the deposited clay approximates 50 percent . One test sample , composed of kaolinite , showed very high yield , 13 to 16 kg per kwhr ; high recovery , 53 to 58 percent ; and 52 to 54 percent solids in the cake .

Jan 1, 1964

By M. N. Pons, E. Benizri, B. Laubie, A. Bani, Université de Lorraine LRGP, P. Kidd, A. J. M. Baker

"Serpentine (i.e. ultramafic) outcrops in Europe cover more than 10,000 km2 and have a low-fertility and low-productivity, making them unattractive for traditional agriculture. In general, these areas are slowly abandoned by local farmers, affected by strong rural exodus and landscapes undergo a process of closure. However, ultramafic landscapes have the potential to provide multiple ecosystem services that can contribute to Europe’s goals towards insuring food security, production of renewable raw materials and renewable energy. Phytomining (agromining) aims at cultivating metal hyperaccumulator plants that are able to accumulate Ni and other strategic elements from metal-rich soils and transport them to the shoots (>1%), which can then be harvested as a bio-ore. Such metal-rich biomass can be used to recover highly valuable metals, e.g. nickel (Ni) and also to produce energy (heat, electricity). Nickel agromining can thus offer an eco-efficient alternative to classical pyro- or hydrometallurgical processes without disturbing the soil cover and the geology from soils and rocks that would be considered as low grade ores or sterile material for conventional mining methods.Phytomining agroecosystems can lead to better soil resource efficiency and can offer a fully integrated, new agromining agriculture that could cover thousands of km2 in Europe, benefit local communities with a sustainable rural development and provide a wide array of ecosystem services which will need to be optimised under a life cycle assessment methodology:1. Production of bio-sourced metal products2. Production of energy biomass3. Restoration of soil fertility for conventional agriculture (Ni stress)4. Limiting Ni intake by local populations and farmers5. Use and conservation of local biodiversity (plant and soil fauna and microflora) as cultivated ecosystems6. Store carbon in cultivated soils7. Enhance pollination activity at landscape level.Nickel agromining could therefore change the economical balance in historically-disadvantaged ultramaficregions of Europe"

Jan 1, 2016

By T. R. Ellis

Many appraisers/valuers believe that the only valuation method available within the cost approach category for real property appraisal is the depreciated replacement cost method. Some valuation and financial reporting standards setters also believe the same. This paper introduces the minerals appraiser to a number of useful methods for mineral property appraisal that are based primarily on the principle of contribution to value, the predominant economic principle in the cost approach. Most of these cost approach methods discussed are primarily for use in valuation of exploration tracts and resource properties that have no defined reserves. However, the powerful rural cost method can be used to calculate the contribution of categories of resources, reserves and other property components to the value of a mineral property. This method can be applied to mineral properties at all stages of development, including producing properties. The author reasons that standards and regulations pertaining to real property valuation should be modified, and underlying principles should be expanded, so as not to inhibit appropriate application of these cost approach methods.

Jan 1, 2011

By W. J. Bennett

WHEN Dr. Horace Fraser, your President, invited me to speak to you today I advised him in confidence that I was leaving my present positions on April 30th. In the circumstances it seemed to me that this audience might prefer to have as its speaker one who wo.uld J1ave a continuing association with the atomic energy programme. Dr. Fraser was kind enough to suggest that my re-marks might he of special interest to you, since I would be able to sum up my views on the atomic energy programme. I hope that I will not disappoint him or you on that score. I am particularly pleased that my last public appearance in my present positions should be at the Annual Convention of the C.I.M. since, as all of you know, a very important part of my work has been in the mining field. As it happens, my first public address on the subject of atomic energy and its raw material -uranium -was made at your Annual Convention in Montreal in April, 1949. It seems fitting that my final address should also be made at this convention -nine years later.

Jan 1, 1958

By R. W. Ruddle

The present state of knowledge on this subject may briefly be summarized as follows: (1) The copper content of the slag increases with the grade of the matte in contact with it; on the other hand, the proportion of copper lost decreases as the matte grade increases, because as a general rule a smaller volume of slag is produced when a high-grade matte is made. (2) The presence of CaO and MgO in the slag decreases the copper content of the slag, and the presence of ZnO increases it; the presence of A1203 seems to have little effect. The influence of the silicate degree is not yet clarified, but on theoretical grounds it seems likely that the copper content increases with the silicate degree of the slag. (3) High slag viscosity, high magnetite contents and low density difference between matte and slag all tend to increase the copper loss. The volume of slag is also an important factor. (4) The effect of bath temperature on the copper loss is not clear and further investigation of this point is needed. (5) It appears possible to recover a large part of the copper in the slag by adding FeS, CaS and other sulphides

Jan 1, 1953

Table A. Conversion of English to SI Units Table B. Strength Properties of Rocks Table C. Engineering Properties of Rock Table D. Properties of Common Minerals Table E. Material Properties and Characteristics Table F. Heat Value of Various Fuels Table G. Geometrical Relationships and Mensuration Formulas Table H. Standard Sizing and Meshes Table I. Ship Measures Table J. International Atomic Weights Table K. Time Value of Money Factorsfor Discrete Compounding

Jan 1, 2008

By H. C. Weed

THE Inspiration Consolidated Copper Co., located in the Globe-Miami district at Inspiration, Ariz., became a producer of copper in 1915. From 1915 until 1948, 116,278,000 tons of ore were produced from underground workings by the block-caving system of mining. In April 1948, open-pit ore production from portions of the ore body was started and earlier plans for block-caving in these areas were abandoned. The change was due to economic conditions.

Jan 8, 1950

By P M. Ashley, M T. Costelloe

The Mary Kathleen tailings storage facility (TSF) contains 7.1 Mt of uranium mill tailings. This waste repository was rehabilitated in the mid-1980s using a multibarrier dry cover. At the time of mine closure, it was predicted that acid mine drainage (AMD) generation would not eventuate and that uranium, heavy metals and radionuclides would be adsorbed within the tailings and not seep from the TSF into the environment. This study reports on the environmental status of the TSF. Gamma-ray measurements indicate an intact dry cover of the waste repository. However, seepage (~0.5 L s-1) of acid (pH 5.71), saline (0.31 per cent), high conductivity (8.8 mS cm-1), slightly oxygenated (DO 2.6 mg L-1), radioactive waters occurs from the toe of the tailings dam into the former evaporation ponds and local drainage system. Seepage waters are calcium-magnesium-sulfate rich with elevated Fe, Mn, Ni, U and Zn values. Oxygenation of tailings seepages causes the precipitation of Fe and coprecipitation and adsorption of other metals (Pb, U, Y), metalloids (As), rare earth elements (Ce, La) and radionuclides (U-235, U-238, Th-227). In contrast, Ba, Ni, Sr, Mn, P, S, Ca, Mg, Na and K as well as Ra nuclides (Ra-226 and Ra-228) remain in solution until pH neutralisation and evaporation lead to their precipitation in efflorescences and sulfate-rich evaporative sediments further downstream. Dry capping of Mary Kathleen uranium mill tailings has resulted in physical containment of the wastes. The dry cover shows no signs of erosion and radiation levels are within acceptable limits. However, the flow rate of surface seepage from the TSF occurs at a much higher rate than predicted. Also, the neutralising potential and adsorption capacity of the tailings and underlying aquifer were overestimated at the time of mine closure. AMD has developed mobilising metals, metalloids, rare earth elements, alkalis, radionuclides and sulfate from the waste repository into surface water seepages.

Jan 1, 2003

By A Winchester, D Grant

The massive 1100 Orebody in Mount IsaÆs X41 Copper Mine has been extracted over the last 40 years form north to south utilising sublevel open stoping methods.De velopment has continually stepped ahead of production to provide access to new primary stoping blocks. The remaining secondary pillars contain stopes with one, two or three fill mass exposures and were constrained by access requirements and stope extraction turnaround time.The remaining southern mining areas consist of large 40 m wide by 300 to 400 m long east-west transverse pillars that have been left to provide access for ventilation and service requirements. Three large transverse cross-cuts or transverse pillars û 4180 x/c, 4010 x/c and the Panel pillar now remain. The 4180 x/c was the last major transverse pillar to be successfully broken.This transverse pillar is being extracted in a retreating sequence, creating 3SLOS stopes due to the surrounding backfilled stopes.In recent years the extraction of the first, and most critical, stopes in the transverse pillars have resulted in large changes to the induced stress field. This paper describes the extraction of the 1.1 million tonne stope P418 in the 4180 x/c pillar.T echnical challenges that were faced and how they were overcome to allow for the successful extraction of the stope are described.Critical to the success of the P418 stope extraction were the rehabilitation methodology used; extraction strategy modifications to address deteriorating ground; mass firings with multiple directional changes; managing the exposure of backfill of variable strengths; and geotechnical monitoring prior to, during and after extraction.

Jan 1, 2005

By Richard L. Jenkins

Systematic sampling, in reconnaissance fashion, of the continental shelves of the United States to define favorable areas of offshore mineral deposits, is one of the long-range marine mineral; programs of the U.S. Department of the Interior. In mid-1966 the Department of the Interior launched its Heavy Metals Program to stimulate domestic output of gold which is in serious short supply. The program is jointly conducted by the Geological Survey and the Bureau of Mines.

Jan 1, 1968

By D. Tahija

"Carbonic acid prepared on-site from carbon dioxide gas is widely used in water treatment and increasingly in some industrial applications. It has not seen extensive use in mineral processing but is an attractive alternative to sulphuric acid for pH control, with the need to counteract high pH levels caused by cemented backfill of particular interest. The fundamental chemistry of carbonate solutions as applied to flotation and flocculation circuits is described as well as plant-scale application. A project to introduce use of carbon dioxide for pH control at the Hecla Greens Creek lead-zinc-silver-gold operation is planned to begin operation in the first half of 2015. INTRODUCTION Flotation pH Control and Backfill Most sulphide flotation circuits are run at pH values ranging from slightly acid to strongly basic, with slightly basic pH the most common. Lead sulphide circuits are typically run at values from 7.5 to 9, with zinc circuits running at higher values of 9.5 to 10.5. This has been the case with ores that produce a natural pH in the circumneutral range, so that the pH needs to be raised. Although lime [Ca(OH)2] is the cheapest reagent in use to raise pH, soda ash (Na2CO3) or caustic soda (NaOH) are also employed where sodium ions in solution are preferred to dissolved calcium, or, in the case of soda ash, the presence of carbonate is desired. The use of soda ash for pH control in lead circuits has been widely recommended for many decades (1). The situation is necessarily different at operations where cemented backfill is used in underground mines (2). Backfill, whether emplaced as rammed paste or pumped slurry, is composed of mill tailings mixed with around 10% Portland or similar cement. When later mining occurs near or adjacent to previously backfilled areas, a considerable amount of old backfill is inevitably mixed with new ore and shipped to the mill. Depending on orebody geometry, mining methods etc., the amount of backfill in mill feed can easily approach 20%, with periods of higher content not unheard of. The presence of so much backfill, with its high cement content, produces results largely indistinguishable from adding a large amount of lime to run-of-mine feed: mill pH in the grinding circuits can range above 11 and high concentrations of calcium ions are present. The need to raise pH disappears; the problem becomes to lower it."

Jan 1, 2015