Search Documents

By Leland E. Paulson

The Grand Forks Energy Research Center and Commonwealth Edison of Chicago jointly conducted tests in which 400 tons each of subbituminous coal and lignite were dried in a commercial scale dryer, oil sprayed and cooled, then shipped in open-top rail cars from Pekin, IL to Grand Forks, ND and stockpiled. Cars containing raw coal and dried coal that had not been oil sprayed were also transported for comparative purposes. The tests were conducted in August and November of 1974. The subbituminous coal was dried from 26 to 16 pct moisture and the heating value was upgraded from 8,420 to 9,650 Btu/lb. The lignite was dried from 39 to 22 pct moisture and its heating value was increased from 6,420 to 8,300 Btu/lb. Before loading subbituminous coal was cooled to 115° F and sprayed with oil at a rate of from 2 to 6 gal/ton. Similarly, lignite was cooled to 85° F and oil sprayed at rates of from 1 to 2 gal/ton. Both shipments arrived in Grand Forks with a minimum of difficulty. The subbituminous coal was subjected to 2 inches of rain during transit with no change in average moisture content. The cars containing dried and oil treated coal had less material lost to wind than either cars containing raw or untreated dried coal. With both dried lignite and subbitnminous shipments, a moderate increase in temperature was measured during transit. With the subbituminous shipments, ignition occurred near poorly fitted bottom dump doors, but was limited to a very small area. The dried lignite was shipped when ambient temperatures were below freezing, and frozen coal was noted around the edge of the car. At Grand Forks, the coal was stockpiled using proven techniques and has remained stable to this date.

Jan 1, 1975

By Takayuki Watanabe, Yoshiki Shimizu, Yusuke Moriyoshi

"B-C-N nanotubes prepared by a flush evaporation method using a de arc plasma were mainly characterized by transmission electron microscopy (TEM) and electron energy· loss spectroscopy (EELS). The nanotubes obtained· were divided into three types such as carbon boron nitride and carbon or carbon nanotubes surrounded with boron nitride nanotubes. These types of nanotubes were obtained at higher temperatures than about 3000 K, however, these were not formed at lower temperatures than about 3000K. On the other hand, 11anocapsules were· formed at all the experimental temperatures and nanocapsules with a homogeneous phase were obtained at lower temperatures than about 3000 K. The effect of additives on the formation of B-C-N nanotubes was not clear. Based on these experimental data depending on temperatures and corresponding microstructures, the formation mechanisms of both nanotubes and nanocapsules were briefly .discussed 1 Introduction As reported previously, nano tubes have unique electrical properties1, 3) The preparations of nallotupes have been usually carried out by flush evaporation methods using either a de arc plasma or a laser4 -5) By these methods the reaction rate is so rarid that we have no data of intermediate products between initial raw materials and. final products of nanotubes 6-9). So, the formation mechanisms of nanotubes have been mainly speculated only from the microstructures of resultant nanoiubes. In order to have more reliable formation mechanisms, it is particularly important to have the information of intermediate products at the corresponding temperatures. From the viewpoints, we have studied about the effects of temperatures on the preparation of nanolubes. Here we report mi firstly some problems on the preparation of B-C-N nanotubes 10), secondly the effects of temperatures on the preparation of B-C-N nanotubes, and finally the formation mechanisms of nanotubes."

Jan 1, 2000

By Isabela Costa Mendes Peres

As soldas dissimilares de liga de níquel 182 são utilizadas em usinas nucleares para conectar tubulações de aço inoxidável com componentes fabricados em aço de baixa liga. O procedimento envolvido na soldagem dissimilar pode modificar as propriedades do material, o que afeta diretamente a junta soldada no sentido de aumento da probabilidade de incidência do processo de corrosão. Neste trabalho foi realizado a soldagem dissimilar de corpos de prova dos aços de baixa liga e aço inoxidável austenítico AISI 316L com as ligas de níquel 82 e 182. Estudou-se o comportamento frente à corrosão da junta de solda de liga 182 em ambientes ácidos contendo NaCl e Na2S2O3 empregando-se técnicas eletroquímicas. Ensaios de polarização anódica potenciodinâmica foram utilizados para caracterizar o comportamento de corrosão localizada do material. Os resultados mostraram que o comportamento eletroquímico da junta de solda está relacionado com o aporte térmico e a presença ou não de oxigênio no meio.

Aug 8, 2018

By Frank L. Hess

In 1876 cassiterite was identified in the placer gold from the northern Black Hills, and such a mixture could have come only from Nigger Hill or one of the streams draining the hill, because in no other hart of the northern hills have cassiterite anti gold been found together. Nigger Hill is in western Lawrence County, South Dakota, and on it is the little camp of Tinton. The Wyoming line runs along the west side of the hill and crosses the ridge which is the hill's continuation about miles north-northwest of Tinton.

Jan 1, 1938

By Douglas B. Silver

"Editor’s note: Douglas B. Silver, Portfolio Manager, Orion Resource Partners, was the keynote speaker at the 2017 SME Annual Conference & Expo in Denver, CO on Feb. 19, 2017. He also gave the keynote address to the SME Annual Conference in 2008. The following is his 2017 keynote address with a few of the slides that were presented. The full speech is available on YouTube https://www.youtube. com/watch?v=uF0qwGJIX3UIn 2008, I had the privilege of giving SME’s keynote address. At that time the financial markets were on the verge of collapse and my presentation described the issues. Unfortunately I was correct, and global markets went into a steep nosedive, creating the largest economic downturn since the Great Depression.In hindsight, there were plenty of signs that this was coming. The Supercycle had created massive new wealth. This wealth was largely invested in the United States due to the country’s political stability and credit worthiness. In 2004, the large investment banks convinced the U.S. Securities Exchange Commission (SEC) to allow them to triple their borrowing leverage ratios. This made the banks more vulnerable to market volatility. The banks then lent money to NINJAS - people with no income, no job and no assets. Even worse was the fact that these unqualified home owners used adjusted-rate mortgages (ARMs) which they, of course, intended to refinance prior to interest rates rising. These mortgages were then bundled up by the banks and sold to investors as “safe” investment products. The money flowed into these products because the rating agencies gave these instruments high marks. These same agencies earned their fees from the very same banks seeking high ratings. (No conflict there). Private debt exploded and peaked out in 2008.These mortgage products were sold in an unregulated shadow banking system and the ARMs came due. Toxic mortgage default rates skyrocketed and the mortgage-backed securities collapsed in value. This house of cards had a negative feedback loop that accelerated the market crash and resulted in more than $1.5 trillion being lost in the securitization sector, a 47 percent decline in the Dow Jones Industrial Average, foreclosure rates skyrocketing and housing prices collapsing. The financial markets were in a nosedive."

Jan 8, 2017

By T Sparks

The Collie River catchment, located approximately 200 km south of Perth, covers an area of around 2830 km2 and is the source of run-off to the Wellington Dam, an important irrigation water resource for the Collie Irrigation District. The salinity of the Wellington Dam has increased due to historical clearing and irrigators currently use water with salinity levels approximately twice that of the Murray River in South Australia (Water and Rivers Commission, 2001). The Collie River Salinity Situation Statement (2001), released by the Water and Rivers Commission (now the Department of Water), identified realistic actions that could achieve the salinity reduction target. Subsequent benefit-cost analyses and prefeasibility studies recommended the diversion of the most saline flows in the Collie River away from the dam as an immediate intervention (URS, 2003). The East Branch of the Collie River above the locality of Buckingham (20 km east of Collie) contributes around half of the salt that flows into the Wellington Dam and the diversion and storage of the saltiest flows from the East Branch at Buckingham was identified as a viable option for reducing salinity in Wellington Dam. The proposal had one problem û the water could not be disposed of as quickly as it was diverted. However, in the vicinity of the diversion site were a number of coal mine voids and after preliminary discussions, the Government/Griffin Coal alliance was formed and from this the opportunities have continued. Diverted water would be stored temporarily in an adjacent mine void (Chicken Creek 4 void) and then disposed of to the sea. The disposal options included Western Power CorporationÆs saline discharge pipeline from Collie Power Station, or a new pipeline. The diverted water was also identified as a potential raw source for treatment and use in industry. This has opened up opportunities including desalination, water efficiencies in the power stations, increased reliability of water supply for the power stations, water for new industries, wastewater disposal options and extra water for PerthÆs water supply. In the process of solving the water storage problems the project introduced a range of mine water quality problems û heavy metals and pH û and the Department of Water (DoW) is now working with the mining industry and the Centre for Sustainable Mine Lakes (CSML) to develop treatment and management technologies. The project has received support and funding through the National Action Plan for Salinity and Water Quality (NAP) and it has been possible to accelerate and enhance this project as a result of NAP. The DoW has developed the proposal to an advanced stage and gained approvals for the capital diversion program to go ahead. The partnerships have expanded to include the second mining company, Premier Coal, the Water Corporation, Western Power and the Harvey Irrigation Cooperative. The proposal could feasibly result in a $90 million integrated water management initiative for Collie using the latest technology, mining operations and providing water for value adding industries in the local area. The DoW is not a mining company; however, our experience in managing water in times of shortage, environmental water quality criteria, competition for water and managing community expectations will have the same success factors:consultation and knowing your community and stakeholders, sharing issues and working in partnership can provide results far greater than the initial issue, even brackish water has value, every sector is in competition with each other and has to have a share of the water, an integrated approach can provide opportunities for development in areas of water shortage, and never think of water as wastewater.

Jan 1, 2006

By W. M. Myers

MINERAL Economics is the most recent profession to be recognized as a separate division of the mineral industries. It has originated from the increasing awareness of the importance of the economic aspects of industries concerned with discovery, extraction, and utilization of minerals. It is concerned with the interrelated fields of economics and technology. The individual trained in economics alone cannot qualify. The curriculum in the School of Mineral Industries at The Pennsylvania State College was approved in May 1946, and enrollment begun in September of that year. Due to the transfer of advanced students from other courses, particularly metallurgy and electrical engineering, it was possible to graduate the first seniors in June 1947. The next class was graduated in February 1948. From experience derived from placing these graduates in industry, and from information supplied by prospective employers, valuable data have been obtained in the organization and operation of the course of study.

Jan 1, 1948

By S Lockie, G Ivanova, J Rolfe

One of the consequences of mining expansion in the Bowen Basin region of Central Queensland in Australia has been a substantial increase in demand for housing, with subsequent impacts on housing and rental markets. Those pressures are reduced to some extent by a proportion of the workforce choosing to live in other centres and commuting to workplace for block periods. The main factors influencing location choice are: housing availability and affordability, basic urban services and lifestyle of the town and the town physical attractiveness such as coastal town. Low costs housing provided by the mining company acts as an attracting factor for some miners to live in the mining town. Recommendations for three short-term and two long-term strategic policy guidelines to address housing situation and location issues are provided.

Jan 1, 2009

By B. Simser, T. Butler, A. Hall

The longterm future of Glencores’ mining operations in the Sudbury basin area of Ontario, Canada likely depends on mining deposits at depths below two kilometres. To gain a better insight into the rockmass response to mining, a geological scouthole program has been implemented at Glencores’ Nickel Rim Deep and Onaping Depth Project to gain insight into rockmass conditions ahead of the devel-opment face. The scouthole program involves drilling long (up to 600 m) subhorizontal boreholes drilled ahead of the development end and collecting data about the rockmass conditions from various geophysi-cal and mechanical tools (in addition to conventional core logging). Once all data has been collected and the borehole is available, seismic sensors are installed up to 450 m down the hole as part of the micro-seismic monitoring program with the leading sensor always located ahead of the development end. The recorded seismic data is used to provide realtime insight into the rockmass response to mining. On May 20, 2017 a flurry of seismicity with a maximum moment magnitude (Mw) of 0.7 occurred causing damage to the ramp heading. Data from the microseismic monitoring system had indicated that conditions at the development end were changing prior to the rockburst. A back analysis of the scouthole data indicated a clear anomaly in the rockmass at the location of the rockburst. The scouthole data also provided sufficient information to suggest that once this anomalous zone was exited, mining conditions would improve. With the microseismic monitoring system providing realtime information from the rockmass, the area was re-habilitated and ramp development continued successfully. Details of the rehabilitation and adjustments to the ramp development are discussed. Some correlations between the scouthole data and recorded micro-seismicity are also presented.

Apr 26, 2022

By J. F. Colinet, W. R. Reed, J. D. Potts

Dust surveys were conducted at six underground coal mines to determine if deep-cutting practices expose face workers to higher levels of respirable dust. The surveyed mines were able to successfully mine deep cuts without significantly increasing the dust exposures of face workers. In general, all of the selected mines exercised good dust control practices by maintaining water sprays, scrubber airflows, proper curtain setback distances and providing sufficient airflow to the active faces. For exhausting face ventilation, field data indicate that scrubber airflow is the most important factor for controlling dust. Data collected for this study indicate that 20-mesh screens should be cleaned for every 12.2 m (40 ft) of advance, because 22% of the deep cuts surveyed for this study experienced a 20% to 35% decrease in scrubber airflow over the course of the cut. For blowing face ventilation, field data and past research indicate that dust control is aided by maintaining a proper curtain-to-scrubber airflow ratio of 1.0 (measured before scrubber activation), as well as a curtain setback distance that allows the miner operator to stand at the mouth of the curtain for the entire cut. Dust levels on the bolting faces did not appear to be affected by the longer cycles associated with deep-cut mining when good ventilation practices were used.

Jan 1, 2011

By John Furness Park

This paper, which describes the mining methods and practices at the Jarbidge mines of the Elkoro Mines Co., is one of a series of papers being issued by the United States Bureau of Mines on mining methods and costs in various districts throughout the United States. LOCATION AND HISTORY The Elkoro Mines Co.'s property is located at Jarbidge in the northeast corner of the State of Nevada (fig. 1). The camp is 9 miles south of the Idaho line; the nearest railroad point is 70 miles to the northeast at Rogerson, Idaho. A road leading to the south and connecting with Deeth, Nev., is passable during the summer months; the heavy snowfall which generally takes place early in the winter usually closes the road until the first of July.

Jan 1, 1931

By Marc Piard

In a cool mine, tapping high-pressure lines through reducing valves lowers the temperature beyond remedy. It is the writer's suggestion that, for low-pressure work, law-pressure air ,should be generated in a compressor installed underground adjacent to the work, and that the jacket-water of the compressor should be utilised for re-heating purposes. Such a system of compressed air distribution, designed especially for service in cool mines, is described in the following notes. The suggested system includes a three-wire pole line from the sub-station to the opening nearest to the working face, with a cable connection extending to the latter from the openings; an electrical centrifugal unit; a reservoir excavated in the ground; and a distribution line, re-heated by jacket-water. As regards the reservoir, it may be pointed out that in many mines there are blind or abandoned tunnels that could be used for the purpose. The centrifugal type of compressed air machine is a comparatively new departure, and it was formerly considered that such a machine, operating at less than 1,000 kilowatts per unit, would be commercially impracticable. At the present time, however, these machines are being built in Europe for as little as 400 kilowatts per unit, and as much as 110 lb. per sq. inch pressure. One advantage which these centrifugal machines have over other types is that they may be driven by plain induction motors, without the help of special starters-a consideration of the first importance where the electrical regulations are severe.

Jan 1, 1926

By J. M. GLEDHILL

IT would doubtless have been felt by many but a few years back that there was little left to be said on the subject of crucible tool-steel, and that something akin to finality had been arrived at in its manufacture and general treatment. Probably such feeling was justifiable when it is remembered that the making of steel in crucibles is by far the oldest method known, dating back from time immemorial, it being indeed impossible to accurately trace its origin and earliest development; but it seems certain that carbon-steel was made and used thousands of years ago for cutting-tools. Proof of this may be seen by the marvelous carvings and workings on the intensely hard stone-work of the ancients, for it would be difficult to conceive by what means, other than with steel tools, such work could have been executed; and it is wonderful to contemplate that steel cutting-tools should have been used so long ago, whilst the principle of manufacturing them-that is, by fusion of iron and charcoal in crucibles-was then in a measure on the sane lines as we work on at the present day. Archaeologists have discovered that the Chinese made steel in crucibles long before the Christian era. " Wootz " steel fabricated in India centuries ago was crucible steel, as was also the celebrated Damascus steel, produced at the forges of Toledo, and, curiously, this latter steel furnishes' yet another proof that "There is nothing new under the Sun," for it is recorded that Damascus steel contained certain percentages of tungsten, nickel, manganese, etc., some of the very elements, in fact, contained in the present modern high-speed steel, so that a latent high-speed steel may be said to have existed

Mar 1, 1905

By L. E. Mylting

Modern ash handling systems exist in considerable numbers and a great deal of design and operating experience has been accumulated, It is the endeavor of this paper to point to a number of frequently recurring problems, A general appreciation of these problems will be helpful in both design and operation of systems. The light fly ash and the heavy bottom ash present different problems, and each will therefore be treated separately. Fly ash is collected in the ducting from the furnace to the stack and beneath the mechanical and electrostatic dust collectors. The greatest amount of dust is collected beneath the mechanicals and electrostatics. Hoppers are generally provided as integral parts of the collector. Suitable valves and piping are connected to these hoppers for removal of the dust. The size and shape of these hoppers are important factors in determining frequency of handling and the capacity of the system.

Jan 1, 1958

By Schwartz M.

Madagascar's democratic election has led to a return to its position as a preferred trade partner with the USA and a priority market with Canada. Michael Schwartz takes a look at two key mining projects in this recently reinvigorated country

Feb 1, 2015

By D. J. McCulla

Mineral development and utilization affect the health of the economy and the pattern of long-term development throughout Canada. There are many diverse opinions on the contribution of minerals to the economy, but there is a dearth of adequate quantitative information. This paper discusses some recent research and provides some new information.

Jan 1, 1977

By Wilford S. Wright, Harold E. Heide, Robert L. Thorne, Neal M. Muir, Aner W. Erickson, Bruce I. Thomas

A program of investigation of strategic and critical minerals began in 1940 to examine and develop tungsten occurrences in the western United States and Alaska. During the years in which the nation was at war, this work was given special impetus to stimulate domestic production. This report is a compilation of results of the tungsten investigations in Alaska supplemented by certain data made available by the Territorial Department of Mines and is designed to include in its scope descriptions of all known tungsten occurrences in the Territory. Two areas in Alaska warranted special investigation - one at Gilmore Dome, 16 miles northeast of Fairbanks, and the other in the Hyder District, at the head of Portland Canal. Three tungsten properties - the Stepovich, Colbert, and Yellow Pup - are at Gilmore Dome. The Stepovich property, referred to sometimes as the Cleary Hill tungsten deposit, was worked by the Cleary Hill Mines Co. from April 1942 until May 1944 and was first examined by Robert S. Sanford and Norman Ebbley, Jr., engineers of the Bureau of Mines, in September 1942. The Cleary Hill Mines Co. by that time had explored an 800-foot strike length of the ore zone with 10 bulldozer trenches and was sinking an inclined shaft on ore in the central portion of the explored zone. In January 1943, the senior author, in company with Ebbley and Harry C. Doheny, supervising engineer of R.F.C., examined the property. Preliminary work by the Bureau of Mines began in May 1945, but actual exploration did not commence until late in June and continued until the end of October 1943. The deposit was examined by John B. Mortie, Jr., and William C. Overstreet, of the Federal Geological Survey, in 1942, and this study was continued in 1943 by Frank Byors, who also assisted the Bureau’s engineers on geologic problems. A magnetometer survey of this area was undertaken in 1942 by Henry Joosting and Eskil Anderson, engineers of the Territorial Department of Mines, and was completed with Bureau of Mines assistance in 1943. During 1943 the Bureau completed exploratory projects on the Cleary Hill mine and adjacent Colbert prospect. The field work on the Colbert property was begun early in July 1945 and continued intermittently until the end of October 1943, when it was recessed because of subzero weather. During September 1944, the Bureau of Mines established (by means of a few surface trenches) continuity between the Colbert mineralized zone, high on the dome, and the Yellow Pup vein, the lowest known tungsten mineralization in the area. It is generally recognized that any extensive program to develop the area as a whole logically would be carried out from the lower horizon.

Jun 1, 1948

By Toby Forney, Joshua Schoonover

In typical surface quarry operations, productivity and efficiency related to pit development begin with drilling and blasting efforts. By embedding technology within drilling and blasting operations, blast results can be tailored to benefit the quarry by driving continuous improvement of production. This technical paper will focus on the continuous improvement efforts at a cement limestone quarry in Maryland and how those efforts have impacted mining production, safety, and efficiency with the application of specific blasting technologies.

Feb 6, 2023

By Clyde E. Williams

IN planning a postwar program for manufactured products, it is essential that the bases for the plans be wisely chosen. First we must make certain assumptions as to the war's ending. Let us assume: (1) complete victory by the United Nations, (2) peace terms that will ensure the direction of the economy of all nations of the world toward peaceful pursuits, and (3) an early ending of the war, that is, before the nations of the world, excluding the enemy, are near the point of physical and spiritual exhaustion. Thus, our manufacturing plants and transportation facilities will still be in good shape. The plants and transportation facilities, as well as the cities of a large part of Europe, however, will be badly crippled. The rich mineral and other raw material resources of the world, little of which was under control. of the Axis powers before the war or will be after the war, will not be used up. Control of these raw materials, or at least an important part of them, will remain in the hands of the strong peaceful nations.

Jan 1, 1943

By T. M. Garland

A nomographical approach is proposed as a fast, easy-to-use, and reason- ably accurate method for estimating expected discounted cash flow (DCF) rate of return and payout time for onshore development drilling and oil production. All costs pertaining to drilling, completing, and equipping development wells, annual expenses of operation, maintenance, and taxes incurred in producing properties, and crude oil prices were considered in developing the nomographs. This report briefly outlines the origin, derivation, and use of the nomographs.

Jan 1, 1973