Search Documents

By F. E. Harris

IT has been said that carbon is "ubiquitous" with reference to iron alloys. Certainly at temperatures where carbon and iron form the solid solution, austenite, it may be readily added to, or removed from, steel surfaces. Differences in concentration potential are the sole requirements for carbon flow. To measure the rate of carbon flow, a proportionality factor, D, is arbitrarily expressed in units of (length)2 X (time)-1. If the term used for carbon concentration is weight pct C, as is customary, then a factor must be found, changing this term to one of weight per unit volume when the diffusion coefficient, D, is used in flow formulae. The determination of D values for carbon is complicated since D varies with the concentration itself. The Matano method has often been employed for systems involving a variant D. This method expreses an evaluation of unsteady flow whereby .0 is given a relationship with the numerical value of C-X slopes. The author contends that this solution is incorrect, except when D is invariant. The primary purpose of this paper is to support this contention. Here diffusion is controlled under two conditions of flow. The first part deals with the steady state; the second part considers unsteady flow under definite restrictions. Beginning with the fundamental concept, the development is continued until equations for C-X curves are obtained. The solution is then subjected to experimental data. It is realized that a great amount of reliable data is required for a rigorous proof. No such research is claimed. Instead an attempt is made to set forth the physical significance of the diffusion mechanism, and particularly to express the factors which influence the flow of carbon in austenite. Of equal significance is the implication that gaseous media may be employed with reasonable accuracy in making these determinations. THE STEADY STATE DIFFUSION OF CARBON IN AUSTENITE The fundamental experiment defining diffusion in solid metals may be readily performed for carbon in gamma iron.1 For this experiment a thin plate of medium carbon steel is chosen. The surfaces of this plate may be taken as two parallel planes which may be considered infinite for points well in the center of the planes. These two planes are held at different concentrations of carbon at a constant temperature. This temperature, 1700°F for example, is one where the single phase, carbon in solution with gamma iron, exists. When these conditions are held for a sufficient time the concentration of carbon of the different points of the solid settles down towards its steady state value. At points well removed from the ends, the concentration will remain the same along planes parallel to the surfaces of the plate.

Jan 1, 1947

In-situ leaching of gold deposits has not become an option largely as a result the lack of suitability of cyanide as a lixiviant due to sluggish kinetics and high dependence on the availability of oxygen. A second problem area is the excessive cost of drilling the required number of injection and production wells needed to service a wellfield capable of maintaining any significant throughput or providing and acceptable level of gold production. Well spacing in in-situ leaching operations is limited by solution life, dissolution rate, and the need for solution control. With cyanide the life of an active solution capable of dissolving significant gold is severely limited by the availability of oxygen which cannot be readily replaced while the solution remains underground. The extremely slow gold dissolution rate also necessitates excessive contact periods in order to dissolve coarse gold.

Jan 1, 1991

By S Hapugoda, Y Tang, L Lu

The steel industry is one of the global leading CO2 emitters, accounting for approximately 7 per cent of global anthropogenic CO2 emissions. In 2022, the world produced 1878.5 Mt of crude steel. About 70.8 per cent of the world’s crude steel was produced by integrated steel mills through the blast furnace and basic oxygen furnace (BF-BOF) process, while the remainder was produced largely by mini mills using electrical arc furnaces (EAF). Compared with gas-based DRI and scrap-based EAF processes, the direct CO2 emissions from the BF-BOF process and the coal based DRI and EAF process are significantly more, as both the processes rely heavily on fossil fuels, such as coke and pulverised coal, to provide energy and reduce iron oxides. Hydrogen is very reactive and reduces iron oxides to metallic iron without generating CO2. Therefore, substitution of hydrogen for fossil fuels in these processes presents a good opportunity to significantly decarbonise the steel industry. This paper will first discuss the thermodynamic and kinetic characteristics of hydrogen and carbothermic reductions of iron oxides and then examine the behaviours of different ore types present in Australia iron ores during hydrogen reduction.

Sep 18, 2023

By Kan Aketa

The Japanese iron and steel industry has been developed remarkably, supported by the increase of steel demand. In particular, progress in various technical aspects of the ironmaking process, including burden materials, equipment, and operation has greatly contributed to the increase in productivity and the reduction of the fuel rate in blast furnaces. With the recent rise in the price of petroleum, the conversion of the energy source from oil to coke has resulted in a temporary increase in the fuel rate of blast furnaces.

Jan 1, 1982

By William S. Hannan, H. Rush Spedden

Flotation may be defined as a process whereby mineral particles are concentrated by selective adhesion to air-liquid interfaces. The process involves attachment of desired mineral particles to air bubbles, and removal of the mineralized air bubbles from the surface of the pulp as a mineral concentrate. Problem Although great strides have been made in understanding the principles of flotation, one part of the process which has not been adequately explained is the mechanism by which selected mineral particles become attached to air bubbles. A glance at the froth of an operating flotation cell demonstrates adequately that use of proper reagents and conditions mill result in such attachments; but how such attachment takes place is not definitely known. A better knowledge of this factor might lead to improved flotation practice either through altered machine design or the application of scientific innovations. Direct observation of the behavior of mineral particles and bubbles in an operating cell does not appear promising because of the complexity of the system. For this reason, conclusions concerning the problem must be deduced from theoretical considerations or from observation of simplified systems designed to reproduce conditions thought to exist in an operating cell. Present Theories Two mechanisms have been recognized as fundamental in particle-bubble attachment: gas precipitation and direct encounter. It is a simple matter to demonstrate in the laboratory that attachment can be brought about by either mechanism. As to the relative importance of the two in a particular flotation system, however, there is a divergence of views. Taggart1 states, Under exceptional circumstances sufficient force and time to effect attachment may conjoin in an ore pulp undergoing agitation, and a preformed bubble adhere to a collector-coated mineral particle, but the occurrence is rare. . . . Pulp-body froth flotation effects selection in the body of a conditioned pulp by causing gas bubbles to precipitate from solution in the liquid phase preferentially at the surfaces of collector-coated particles, and to cling to these particles, Gaudin2 states that, within the pulp body of an agitation machine, attachment of mineral particles to air bubbles occurs as a consequence of contact between the two. This theory has been supported by theoretical reasoning and much circumstantial evidence. Perhaps the most interesting bit of evidence in favor Of this theory js the difficulty in the flotation of fines. If attach-

Jan 1, 1949

Experimental petrology may be used to accurately constrain PTX conditions in order to calibrate and understand geologic processes. This method may be used to answer postulated questions, by recreating known geologic conditions and observing changes in the experimental charges. The purpose of this project was to determine the eutectic composition and temperature in the ternary system PbS-FeS-ZnS ¦ (Ag2S), at ambient and elevated pressures and elucidate if the sulfides of the Broken Hill orebody may have been partially molten during highgrade (granulite facies) metamorphism. The study determined the eutectic temperature and composition in the system PbS-FeS-ZnS to be 800¦2¦C and 62.5% PbS, 30.5%FeS, 7% ZnS respectively, at one atmosphere, and the eutectic temperature at 27 kbars was found to be 960¦C¦10¦C, with a eutectic composition enriched in ZnS relative to the one atmosphere eutectic. the addition of lwt.% Ag2S to the system depresses the eutectic temperature to 772¦2¦C at 1 atmosphere and below 810¦5¦C at 5 kbars. The conditions of peak metamotphism for the cental and southern areas of the Broken Hill Block, New South Wales, Australia , lie above the solidus of the PbS-FeS-ZnS-Ag2S system, strongly suggesting that partial melting occurred in the orebody.

Jan 1, 1998

The effect of the chemical composition of pulverized bituminous coal particles on their physical transformation during the initial stages of combustion has been investigated. The results suggested that cenosphere formation does not require extensive thermal decomposition of the coal particles. The vitrinites in the bituminous coal softened earlier and developed larger cenospheres than the othe macerals. The coal particles swell to a higher extent during combustion than in pyrolysis; however, the cenospheres formed in the former process experienced a higher extent of fragmentation. The development of microporosity occurred predominantly after the resolidification of the swelled char particles. The type of macerals originally in the coal did not significantly affect the microporosity of the chars. Conversely, the morphology and anisotropy of the chars were strongly dependent on the maceral composition of the coal.

Jan 1, 1986

By Vishal Shukla, Prateek Singh, D. P. Chakraborty

"Continuous thickening by an operation called sedimentation is the separation of suspended solid particles from a liquid stream by gravity settling. The primary purpose of thickening is to increase the solids concentration of the feed stream. High rate thickeners are designed specifically to maximise the flocculation efficiency. A detailed investigation has been carried out to understand the influence of ore type and operating parameters such as bed level, bed mass, rake arm torque and flocculent concentration on thickening operation. Tata steel’s Noamundi plant data shows that variation in ore type, and operating parameters are major contributors to fluctuation in thickener performance. A lot of research has been done earlier on thickening operation but effect of ore type and operating variables by using plant data was never touched before.In this context, the performance of thickener was evaluated by daily data to study the influence of ore type and operating variables on thickener operation. Investigation shows that friable ore % in feed mix is proportional to slime density because friable ore is porous & brittle in nature. As a result, friable ore generates more fines/ultrafine during communition process in wash plant. Increase in flocculant concentration and bed mass is showing a positive change on high rate thickener performance Investigation shows that optimum bed mass and flocculant concentration is required to achieve desired pulp density in thickener underflow at different feed pulp density (g/cc).INTRODUCTIONOver the years, Iron Ore Beneficiation at Tata Steel, Noamundi has seen varied changes. Depletion of high grade iron and with increasing iron ore throughputs coupled with lowering of the hard ore a subsequent increase in slime generation, slime management and clear water requirement for wet Plant has thrown up myriad challenges. To overcome these challenges, many improvements initiatives were taken by Tata Steel in last decade. One of the major changes is the recent High Rate Thickener commissioning at Tata Steel Noamundi to cater the high iron ore throughput requirement. Slime reporting to Thickener has increased from 1.4 MTPA 2.5 MTPA over the last few decades. The above changes further aggravate the poor settling and dewatering characteristics of the slurry which is being feed to HRT. Considering the above mentioned constraints and stringent environmental implication proper water management has become a major challenge to reckon with. The thickener is used to increase the concentration of the suspension by sedimentation, accompanied by the formation of a clear liquid. In most cases the concentration of the suspension is high and hindered settling takes place."

Jan 1, 2016

By Harlow D. Phelps

"INTRODUCTION The Copper Butte mine was examined, surveyed and mapped (fig. 1) by a Bureau of Mines engineer in January 1944. As a result, it was decided to diamond-drill the deposit, using Bureau of Mines equipment, and drilling was started October 14, 1944, under the supervision of two Bureau engineers, and stopped April 5, 1945. Nine holes were drilled for a total of 1,274 feet, not including 48 feet on a lost hole. Figures 2 and 3 are sections at AA' and BB' of figures 1, and show the adjusted average assays of drill-hole samples. Figures 4 and 5 are separate maps of holes 4 and 6, respectively.ACKNOWLEDGEMENTSIn its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources, to the end that they make the greatest possible contribution to the national security and economy. It is the policy of the Bureau to publish the facts developed by each exploitation project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch, R. G. Knickerbocker, chief, analyzes samples and performs beneficiation tests. Both these branches are under the supervision of R. S. Dean, Assistant Director."

Aug 1, 1946

By J. S. DeLury

Introduction The problems of metallogenesis are largely related to those concerning the origin of igneous rocks, which, in turn, are involved with the question of crustal mechanics. Many ore-bodies are genetically related to associated intrusive and there is an equally close association apparent between igneous intrusion and crustal deformation. The problem of ore-deposition is concerned, therefore, with the fundamental problems of geology. For a long time speculations regarding crustal movements rested largely on the contraction theory and its associated conceptions. Vertical movements were considered to be all important and horizontal movements secondary to them. Magmas were pictured as rising more or less vertically in the crust and were believed to form in vertically disposed magma-chambers or reservoirs. The principle of magmatic differentiation seemed to offer the best explanation of the origin and association of diverse rock types and it seemed also to require the existence of quiescent magma-chambers for the admittedly slow process of differentiation. Accumulating evidence of the importance of horizontal movement in the crust, has, along with other considerations, discredited the contraction hypothesis and many of the inferences that go with it. The same evidence may require some change in the prevailing conception of the origin of the various types of igneous rock and of the mechanics of intrusion. Geologists are now at sea concerning some of the vital and fundamental problems of the crust, and the field is open for speculation. The writer is developing a hypothesis which seems to permit an explanation and? a correlation of earth structures and phenomena. If it rests on a firm foundation, the hypothesis, because it is fundamental, is certain to have a profound bearing on the problems of economic geology. It is for this reason that an outline of the hypothesis is offered at this time. Only a few of its economic bearings are foreseen at this time and these will be indicated.

Jan 1, 1932

By C. R. Watts

The feasibility of producing composites containing nickel or molybdenum fibers in a beryllium matrix was inrestigated. The composties studied were jabricaled by powder mallurgical techniques. The 1-mil-diarr nickel fibers reacled completely below 900°C, converling the fibers .from nickel to Ni5Be2,. As the /LO/-pressing temperalure as raised above 1110oC, tlie nickel diffused outward from the beryllide fibers. The solid solubility of nickel in beryllium was clboul 20 wt pet at the 1100°C pressing temperature a1 the zone-fiber interface. The 1.5-mil-diam molybdenum fibers slzolred no evidence of reaction and little evidence of diffitsion after pressing at 900°C. Between 1000° and 1050°C pressing conditions, the fibers began lo react , producing 1ayers of MoBe2 and MoBe12, respectively surrounding the molybdenurn core. The struture remained the same at 1100°C with no evidenre of solid solubility of the molybdenum in the berylium or vice versa. In recent years a considerable amount of attention has been devoted to the determination of methods for improving the mechanical properties of materials through the use of fiber or whisker reinforcement. Previous work with metal matrix composites indicates that the study of the chemical compatibility of the fiber and matrix is an area requiring greater understanding. The metal-metal or ceramic-metal interface is frequently subject to chemical reactions that may result in the formation of hard brittle intermetal-lic compounds and/or low melting point eutectic compositions. The reaction products may reduce both the low-temperature and elevated-temperature strength of the composite by weakening the fiber-matrix bond, producing premature failure at the interface. It is well-known that most metal-metal systems and many metal-ceramic systems of interest for structural composites are thermodynamically unstable,'-" particularly at elevated temperatures. If, however, the rate of reaction under the conditions of fabrication is sufficiently low. composites can be fabricated that can be used efficiently for indefinite periods at low temperatures and for short periods at elevated temperatures. This paper presents the results of a series of tests to determine the compatibility of nickel and molybdenum fibers with beryllium at various hot-pressing temperatures. Nickel was selected as a candidate fiber material primarily because the relatively ductile fibers might be useful as crack arresters in applications such as ballistic impact where crack growth can result in catastrophic failure. The high density and the reactivity of nickel were primary factors detracting from its selection as a possible reinforcement. Molybdenum with a modulus of elasticity of 52 Xlo6 psi is one of the few metallic materials having a modulus higher than beryllium (42 X lo6). Its high modulus, coupled with its refractory characteristics, made molybdenum an attractive candidate for a relatively stable fiber reinforcement for beryllium. Its density, being higher than that of nickel and over five times that of beryllium: detracted from its other characteristics. EXPERIMENTAL PROCEDURE The specimens were prepared from beryllium powder with a dispersed phase of fibers by powder metallurgical techniques. P-20 grade powder, Table I, from Berylco was used as the matrix material. Short lengths of 0.001-in.-nominal-diam nickel fibers supplied by the Sigmund Cohn Corp. and 0.0015-in.-nominal-diam molvbdenum fibers obtained from the General Electric Co. were used as the dispersed phase. The composite constituents were combined under an argon atmosphere by mechanically mixing the powders and fibers. The compositions used were nominally 1 vol pct fibers. After mixing. the composites were hot-pressed into a-in.-diam pellets under an argon atmosphere at 900°, 1000". 1050". and 1100°C at a pressure of 6000 psi with no hold time at these temperatures so that a comparison could be made between the resultant microstructure and hot-pressing temperature. The billet was heated at a rate on the order of 30°C per min to the desired temperature and then cooled at a somewhat slower rate. The microstructure obtained should be considered as characteristic of the integrated time-temperature history of the sample, as well as the maximum temperature attained. Upon removal from the hot-pressing dies. the specimens were cut. mounted. and polished by standard procedures. No etchant was used in specimen preparation. Photomicrographs, electron microprobe scans, and electron back-scatter pictures were made. X-ray dif-fractometer patterns were made of several of the specimens. but only the lines for beryllium could be resolved. Specimens for optical and electron microprobe examination were selected partially for the roundness of the cross section. A round cross section was taken to indicate that the body of the fiber was approximately normal to the surface and that therefore effects due to fiber material immediately below the surface could be neglected. RESULTS AND DISCUSSION The microprobe scans indicated that nickel reacted as low as 900°C, converting the entire fiber cross section to NisBe21. Fig. l(a). There was no evidence of further reaction from the optical or the back-scatter pictures, Figs. 2(n) and 3(a).

Jan 1, 1970

By S. M. S. Azghdi, K. Barani

The effect of microwave treatment on the surface roughness and wettability of chalcopyrite (CuFeS2 ) and on the chemical composition of its surface was studied. The microwave source was a conventional multimodal oven with frequency of 2.45 GHz and maximum power of 900 W. Pure chalcopyrite specimens and purified chalcopyrite concentrate were used in this study. Analysis using atomic force microscopy showed a decrease in the surface roughness of the chalcopyrite after microwave radiation. This decrease may be due to oxidation of the surface and formation of iron oxide. Moreover, the surface wettability of the chalcopyrite mineral increased with increasing duration of microwave radiation, which was in good agreement with the micro-flotation mass recovery results. The increased wettability of the surface may be attributed to the decreased surface roughness by microwave radiation. Analysis using scanning electron microscope/energy-dispersive X-ray spectroscopy indicate that after microwave radiation, the contents of sulfur and iron increased whereas that of copper decreased on the surface of the chalcopyrite, significantly changing the average atomic number of the chalcopyrite surface.

By M. J. Zdunczyk

Located approximately 50 miles northeast of Knoxville, Tennessee, Short Mountain Silica mines the Clinch Formation, an orthoquarzite, for silica sand. In 1980, a Knoxville resident and area contractor visualized mining Short Mountain for silica sand. Because APG Industries, the main market for the glass sand product, was only 48 kilometers from the site, many silica sand companies became interested in the property. In 1986, J.D. Nicewonder began to develop the site, and in May of 1988, APG Industries received the first sand shipment.

Jan 1, 1992

By D. Harrington

The record of fatalities from mine explosions in the United States during the past 44 years has been the best in the history of the mining industry, despite the fact that the number of fatalities from this cause during the past fiscal year now is nearly double that of the previous year. During there 4 fiscal years, mine explosions have resulted in an average of 45.5 deaths per year, compared with an average of 153 deaths per year for the preceding 5 years; an average of 542 deaths per year for the 3 years 1907-1909, inclusive, and a yearly average of 265 deaths per year for the 20 years prior to 1929. Other types of mine accidents also have been reduced during this period, but not to the same degree or by as large a percentage as mine explosions. The fact that in this fiscal year ended June 30, 1937, electricity was responsible for 60 percent of the explosions and 85.5 percent of the fatalities resulting therefrom (see tables 3 and 4) is evidence that either mine operators are lax in providing proper electrical equipment or there is laxity in the upkeep and use of electricity in our mines and more particularly in our coal mines. Several large coal-producing States that in the Fast have had numerous disastrous explosions have been free from such disasters for continuous periods of as long as 8 years. The bituminous mines of Pennsylvania, one of the largest coal-producing States, give a good example of what can be done to prevent explosions. 'his State, with its large number of operating mines, many with very definite hazards from gas or dust or both, has had only two major explosions (resulting in 16 fatalities) during the past 7 years; this is a decidedly good record compared with any similar period in the past and when it is considered that during this period about 750,000,000 tons of coal have been produced. Other good records are: Tennessee, without a single fatality from explosions during the past 9 years; Alabama, with 6 fatalities during the past 7 years; Illinois, with no explosions during the past 4 years; and

Jan 1, 1938

By Hans von Michaelis

"INTRODUCTIONThe renaissance in gold and silver recovery technology has continued to unfold and it is appropriate to review some of the useful new technologies as well as try to identify some of the industry's future needs and frontiers.The remarkable strengthening in the US dollar has resulted in a relatively low gold price in US Dollars of around $310/oz at the time of writing and silver at $6.25/oz. This general softening in the dollar prices and the recent confusion as to environmental compatibility of cyanidation tailings and effluents, has led to a slowdown in announcements of new operations. Another reason for the slackening off in the USA is that in the past few years a large part of the capital has come from oi I and gas companies that now seem to be losing interest in mineral ventures, and foreign investors for whom the dollar is becoming out of reach. In the author's opinion this represents an unprecedented window of opportunity.Elsewhere in the world where local currencies have weakened, the price of gold is at or close to its all time high.For example, in South African Rands, the gold price was R571.00/oz when the rand was US$1.47 and the gold price reached US$800. Now at US $309/oz and with the Rand at US$0.51 = Rl .00, the local gold price is R600. The price of si Iver in Mexican pesos is not much less than it was when silver reached US$50/oz. Gold, and silver prices in local currencies outside North America are still buovant and at levels where additional investment in new projects is more encouraging.Even in Canada where the dollar is worth about US$0. 75, this provides a smaller but significant cushion compared with US operations. Considering the present strength of the US dollar and even the Canadian dollar relative to many other gold producing countries, there should be significant investment opportunities at today's prices. Mining companies have started to descend on Brazil, for example, where in a matter of just a few years annual gold production has increased from 10 to 70 tons. In South Africa, a Canadian company backed by Swiss financing has been able to take over a Witwatersrand gold mining operation and is installing a huge new tailin9s retreatment plant to process about 1 million tons per month of tailings."

Jan 1, 1985

By C. A. Rawlins

INTRODUCTION Radcont is a program designed by the author of this paper for the industry to use as an instrument for radiation contamination evaluation and ventilation planning system. Radiation in mines are associated with the mining of gold and gold bearing minerals, as uranium and thorium is incorporated in the mining of these minerals. Radiation contamination in South African mines is not a new concept as it was investigated by the Chamber of Mines in the early 1960's and found not to be hazardous at the time. Since some of our mines export scrap metal to customers abroad, it came to light (1991) that some of the scrap metal was radioactive. The authority that oversees the nuclear aspects in South Africa is the Council for Nuclear Safety (CNS). They investigated these matters and found that the mines needed further information regarding radioactive material and the handling of these contaminated materials. As the various mines were licensed (with various conditions incorporated) thereafter, the mines had to do their own investigations as to what extent their properties (Surface and underground) were radioactively contaminated. Some mines were found to be highly contaminated over the years of operation and controlling conditions were installed and measures installed to reduce the contamination levels. One of the conditions when issuing a licence by the Council for Nuclear Safety (CNS), is that a screening survey be carried out to determine the radiation exposure levels and corrective action to be taken if necessary. These surveys must be done by a person trained in the required procedures for such a survey. The person must also measure the risk correctly and assess the results properly. In such a survey, the internal and external exposure levels must be determined to assess the total exposure of persons working in those conditions and take appropriate action if necessary. When doing such a survey, hundreds and more likely, thou- sands of data points are recorded. In order to assess the data recorded, various integrated and difficult calculations need to be made, and takes up enormous amounts of time. (This excludes the interpretation of the results ) The following explanation of the program shows the different parts of such a survey assessment calculations to be done. The paper details the program layout and the different sub- sections within the primary program. It must be stated that the program, as with any other program, is as accurate as the data inserted into the data base. The program and details thereof are given under the following headings: 1. TOTAL EFFECTIVE DOSAGE WITH REGARDS TO: • GME required gravimetric results obtained (mg/m3) • Thick layer or total contamination measured (Bq/m2) • Dry condition surveys with dust loads taken as a Standard l0mg/m3 • Wet conditions survey with dust loads taken as l mg/m3 • Airborne long lived alpha and beta activities as determined by analysis in Bg/m3 • LTD (Thermoluminescent Dosimeter). Results as obtained from the SABS (South African Buro of Standards) are recorded in this section for each month of the year for each individual worker. An average dose is then determined at the end of the year. • Bucket measurements as recorded. • Smear samples (Loose contamination). As determined by Electra or by analysis • Occupational factors for Metallurgical and Engineering occupations in and around the Metallurgical facilities of your mine. • All underground dosage determination and calculations. (Radon and Thoron) 2. INFORMATION REQUIRED WHEN PROGRAM IS INITIALISED: As the program is started, it opens up on the contents page. Here there are various options to choose from, but one is cautioned as a beginner in operating the program, not to perform any tasks before carefully reading these instructions. Firstly, one must go to the 'Information required" pushbutton. Press this button. The information required page is shown where the cursor can be moved to the block where one can enter the specific mines name. To enter a mines name, put the cursor in the block provided and just insert the mines name with the normal keyboard keys and press the enter button on the computer keyboard. To enter the other information required such as Alpha and Beta instrument efficiency, ALI (Annual limit of intake) and probe area, one can either press the 'Data required" button for a dialog box information or enter it manually by just putting the cursor in the block provided and entering as did above. In order to insert all the required information for the pro- gram to calculate the information required, one must proceed further by entering the area names surveyed in the spaces provided. There are 20 spaces to enter 20 different areas surveyed. One must further also provide the amount of days worked in each area (i.8. 250) in the block provided. The de- fault is 250 days. There are also standard information given in the information data page such as breathing rate (1,2 m31h), 8 hours worked per day, 5 days per week and 50 weeks per

Jan 1, 1997

By J. Desroches, J. Burghardt, B. Lecampion, A. P. Bunger

"We present detailed comparisons between theoretical predictions and experiments for the initiation of radial hydraulic fractures transverse to a wellbore. Most of these experiments provide a measure of the time evolution of pressure, length, opening and flux entering the fracture during the test. We compare all these measurements simultaneously to our theoretical predictions, thoroughly testing hydraulic fracture initiation theory, which is shown to be predictive. These comparisons notably emphasize the difference between the initiation pressure (the wellbore pressure for which the fracture initiates) and the breakdown pressure (a misnomer which simply corresponds to the maximum pressure recorded during the test). INTRODUCTION In this paper, we will compare hydraulic fracturing laboratory experiments performed in different tight materials (PMMA, cement, shale) with the predictions from a numerical solution of the governing equations of hydraulic fracture mechanics (e.g. Geerstma & de Klerk, 1969; Detournay & Peirce, 2014). We focus on transverse radial hydraulic fractures initiating from a radial notch at the wellbore wall (see Figure 1). In particular, we will clarify the difference between the initiation pressure (the wellbore pressure at which the fracture initiates) and the breakdown pressure (a misnomer which simply corresponds to the maximum pressure recorded during a test, usually carried out at constant pump rate). This difference stems from the strong viscous effects at play during wellbore pressurization, fracture initiation and early propagation (i.e. fluid entrance in the newly created fracture). It has been observed on a number of experiments (e.g. Weijers, 1995; Zhao et al., 1996) and has a strong practical application, first because the maximum pressure is the most obvious value to report and second because that maximum value is necessary to specify injection systems."

Jan 1, 2015

By J. P. Van Kleunen

9.3-1. Introduction. The demands of industry for handling materials at higher rates and at reduced costs have had a very significant effect on belt conveyor technology. Although the general appearance of the belt conveyor today is essentially the same as it has been for the past several decades, the similarity ends there. Each component comprising the conveyor system has been continuously improved through design and materials technology to enable present conveyor systems to operate at ever-increasing rates and reliability. For example, twenty years ago the strongest commercially available, fabric-reinforced conveyor belting had a tension rating of 50 lb per ply-in. Currently, fabric-reinforced belts are available with ratings of 350 lb per ply-in. and steel cable reinforced belting is available with tension ratings of 3000 lb per in. of belt width (3). These technological advances have therefore enabled the belt conveyor to not only attain acceptance as a preferred method for in-plant movement of bulk materials, but also to be used for long distance transportation of bulk materials, particularly in areas of adverse terrain. The information contained in this chapter is intended to assist the reader to make basic decisions regarding the use and application of a conveyor system. The design of an overland conveyor transportation system or an in-plant process conveyor is accordingly beyond the scope of this article. Many comprehensive technical works covering the design of a belt conveyor are currently available from the manufacturers of materials handling equipment (6, 7, 9, 11). The design handbook published by the Conveyor Equipment Manufacturers Association is particularly recommended (2). 9.3-2. Conveyor Capacities. One of the most important factors in determining the proper size of a conveyor system is the rate at which material must be handled. Although tables and charts are available to the conveyor designer to assist him in his selection of conveyor components, only the

Jan 1, 1968

By A. Kapito

The ferrite-pearlite microstructure is the most popular microstructure for alloys used in structural applications, including railway wagon wheels. These alloys have been designed through alloying and thermo-mechanical processing to have a refined microstructure. Ferrite-pearlite alloys are low cost, weldable, have good fabricability, and are reliable under extreme conditions. Given these performance attributes, it seems unlikely then that their dominant position as structural steels would ever be challenged by alternative microstructures. One major achievement in the development of ferrite-pearlite steels has been in the refinement of their interlamellar spacing to very fine distances of the order of < 0.3 um. A refined microstructure increases the hardness of the alloy, thus increasing its life under wear conditions. The interlamellar spacing in pearlitic steels has, however, been refined almost to its theoretical limit. The increasing demand for speed and increased axle loading on railway wagons requires the use of stronger, tougher, and more durable materials. This has opened the window for the development of novel bainitic steels. Bainitic alloys have a higher level of microstructural refinement than pearlitic ones. They have shown to have good wear resistance and rolling-contact fatigue resistance, and high toughness. This paper will discuss the progress to date on the development of bainitic railway wheel alloys. Four alloy chemistries have been chosen for possible further development.

Jan 1, 2012

By Charles W. Huggins

Knoop hardness indentations were studied and measured with the electron microscope on TiB2, HfC, and A1B12 crystals. A detailed description of replicating the indentations using collodion and Faxfilm is made. A John Hopkins grating having 28,800 lines per inch was used to accurately determine the magnification used on the electron microscope. The primary objectives were to prepare carbon replicas of hardness indentations, to measure the indenations accurately, and to compare the results with those obtained with the light microscope. The resulting data showed excellent agreement between the measurements made on the replicas with the electron microscope and those made with the optical microscope. The replicas made from collodion showed slightly better agreement with the light optical values than did the replicas made from Faxfilm.

Jan 1, 1963