Search Documents

By Xue Wang, Callie Babbitt, Chelsea Bailey, Matt Ganter, Gabrielle Gaustad, Brian Landi

"Current trends, motivated by fossil fuel dependence and unprecedented greenhouse gas (GHG) emissions, show lithium-ion batteries (LIBs) emerging as a competitive energy storage technology due to higher power and energy densities compared to Pb-acid and Ni-metal hydride chemistries. These trends may be of concern, however, as environmental impacts are not well understood for either the LIB itself, or for the nanoparticles consumed or released during the battery's production, use, or end-of-life. This study combines economic modeling, dynamic material flow analysis, and fundamental material characterization methods in order to quantify some of the economic and environmental trade-offs for LIBs at their end-of-life. As expected, results show that as chemistries transition from Li-Co based cathodes to Li based Fe, Mn, and S cathodes, LIB recovery value correlates to the value of the raw materials used. These initial results aim to inform collection policies being proposed currently as well as enable future deployment of novel recycling techniques.IntroductionGlobal fossil fuel dependence and unprecedented GHG emissions have led to increasing attention on energy alternatives, for both electricity production and personal transportation. However, development of renewable energy systems is contingent on concurrent technological development of energy storage systems, primarily batteries used for power grid load-leveling, renewable energy storage, and hybrid and battery electric vehicles. In this sector, lithium-ion batteries (LIBs) are emerging as a competitive technology due to higher power and energy densities compared to lead-acid and nickelmetal hydride chemistries[!]. LIBs represent close to 20% of the total rechargeable battery market and 75% of the portable rechargeable battery market, which is the fastest growing segment of the rechargeable battery market, with a 20% global growth in 2008 [2].This surge in production ofLIBs indicates a looming waste problem; total waste from Li-ion batteries has likely grown substantially from the 500 metric tons estimated in 2003 [3]. Figure IA shows the substantial increase in world-wide lithium production that has occurred in the last several decades with batteries making up the largest share of applications (Figure lB). California and New York state legislators have attempted to proactively address this looming waste by issuing diposal bans on rechargeable batteries in their states[4, 5]. However, quantification of the costs involved in collection, transportation, and processing of these materials has not been examined in depth."

Jan 1, 2012

By M. Polat, S. Chander

Many models have been suggested in the past to obtain a satisfactory fit to flotation data. Of these, first-order kinetics models with a distribution of flotation rate constants are most common. A serious limitation of these models is that type of the distribution must be pre-supposed. Methods to overcome this limitation are discussed and a procedure is suggested for estimating the 'actual' distribution of flotation rate constants. It is demonstrated that the classical first-order model fits the data well when applied to coal flotation in narrow size-specific gravity intervals. When applied to material which is fractionated on the basis of size alone, the use of three parameter models, which were modified from their two parameter analogs such as rectangular, sinusoidal, and triangular, gave most reliable results.

Jan 1, 1995

By D. B. Dow

This paper on the physical chemistry of oil-field emulsions is the last of a series of three prepared as a result of a study of oil-field emulsions. The first paper3 deals with the factors responsible for the formation of emulsions, find the second4 with methods now utilized for dehydrating oil-field emulsions. A more complete report of the whole investigation is in preparation. The laws governing the formation and resolution of oil-field emulsions fall in that branch of physical chemistry doling with colloids. Much work has been done by the physical chemist on colloids And emulsions, and, although most of this work was on commercial and pharmaceutical emulsions, yet the principles developed apply in a general gray to oil-field emulsions.

Jan 1, 1925

By J. J. Arps

This paper reviews the methods currently in use for estimating primary oil reserves and discusses the principles on which these methods are based. Particular emphasis is placed on how these methods change with the type of information available during the life cycle of an oil property. This paper contains various novel estimating methods and shortcuts heretofore unpublished. INTRODUCTION Estimating oil reserves is one of the most important phases of the work of a petroleum engineer since the solutions to the problems he deals with usually depend on a comparison of the estimated cost in terms of dollars, with the anticipated result in terms of barrels of oil. His recommendations to management regarding the best course of action are therefore normally based on the most favorable balance between these two. Specific engineering problems which require such a knowledge of recoverable oil reserves and a projection of future rates are: [a.] the exploitation and development of an oil reservoir; [b.] the construction of gasoline plants, pipelines and refineries; [c.] the division of ownership in unitized projects; [d.] the price to be paid in case of a sale or purchase of an oil property, and the magnitude of the loan which it will support; [e.] the proper depreciation rate for the investment in oil properties; and [f.] evaluation of the results of an exploration program. This discussion will be confined to the various methods and tools which are currently in use for estimating oil reserves to be obtained during the primary phase of an oil-producing reservoir and for a projection of the future production rates. Reserves which may be obtained by secondary recovery methods or fluid injection programs and gas and gas condensate reserves will not be discussed in this paper. Unfortunately, reliable oil reserve figures are most urgently needed during the early stages when only a minimum amount of information is available. Management's interest in the oil recovery from a property—aside from its use for accounting purposes—usually declines when the property approaches its economic limit, just at the time when the reliability of the estimates is at its best. To illustrate this general idea a chart is presented (Fig. 1) showing the three periods in the life of an imaginary oil property. Time is shown on the horizontal axis, while the cumulative production and estimated ultimate recovery are plotted vertically. No particular units are used and this schematical chart is not to scale. During the first period, before any wells are drilled on a property, any estimates will of necessity be of a very general nature, based on experience from similar pools or wells in the same area, and usually expressed in barrels per acre. This will

Jan 1, 1957

By Arthur Phillips, E. N. Skinner

DURING the course of an experimental program concerned with the hydrogen embrittlement of copper containing oxygen in concentrations within the solubility limits it became necessary to make a critical appraisal of the literature dealing with the solubility relationships of oxygen and solid copper. The latest determinations, and perhaps the only data obtained on "spectroscopically" pure copper, are those of Rhines and Mathewson1 who reported that the solid solubility increases from 0.007 per cent oxygen at 600°C. to about 0.015 per cent at 1050°C. Hanson, Marryat and Ford2 had previously placed the solubility limit at less than 0.009 per cent oxygen at 1000°C. and Allen and Street3 had suggested, on the basis of an unpublished research by T. Hewitt, not over 0.005 per cent oxygen at 500°C. In the introductory stages of the investigation indirect evidence accumulated to suggest that the solubility limits were significantly lower than those previously reported. For this reason it was deemed essential to clarify this point before proceeding with a program intended to establish a quantitative relationship between hydrogen embrittlement and oxygen concentrations positively known to be within the solid solution range. Furthermore, the increasing production and the highly selective applications of the commercial "oxygen-free" coppers inevitably direct attention to the practical necessity for exact knowledge regarding the effects of minute concentrations of the elements ordinarily found in the high-purity coppers now available. Of these elements oxygen occupies a unique position, not only by virtue of its specific effects on copper but more particularly in view of its important reactive tendencies toward the other impurities with which it is associated. Rhines and Mathewson considered several methods for measuring the solubility of oxygen and finally adopted the simple plan of saturating the specimens, obtained from redeposited cathode copper, by heating at the desired temperature in air. After the removal of surface oxide by mechanical and chemical means, the oxygen content was determined in the underlying metal. In general, this process of saturation, with a few modifications, was followed by the present writers. Although the procedure is direct and has obvious advantages, its effectiveness, unfortunately, is reduced by an excessive scaling of the copper, particularly at the higher temperatures. After saturation treatments above 900°C. the writers found that the specimens, necessarily rather thin in the original condition, consisted largely of scale and yielded too little metal for a satisfactory analytical sample. Furthermore, great difficulty was experienced in effecting complete removal of the scale. Needless to say, it is necessary to exercise extraordinary care in the preparation of the surface of the analytical sample in order to eliminate submicroscopic fragments of cuprous oxide which ordinarily are lodged in the crevasses and

Jan 1, 1941

By John Lindsay

"Although diamond mining is a relative newcomer to the Canadian mining industry, with the first diamond mine coming on stream in 1998, Canada is already a significant producer of high quality diamonds. This paper will review diamond production trends and highlight some of the projects currently under development, which have the potential to enhance Canada’s role as a significant diamond producer.Diamond recovery plants generally incorporate well-established mineral processing and recovery techniques, with issues such as product security, cut-off sizes, and diamond preservation becoming important considerations when developing process flowsheets. A diamond processing plant must achieve three key objectives, namely:• Liberation of the diamonds from the host rock;• Separation of the heavy minerals, which include the diamonds, from the host rock;• Recovery of the diamonds from the heavy mineral concentrates.Processing technologies and equipment commonly utilized in diamond processing plants will be reviewed and some of the significant issues associated with each option briefly discussed.Typical process flowsheets will be presented.Finally, an overview of De Beers’ Victor diamond project, located in northern Ontario, will be provided. This potentially significant diamond producer is currently at a pre-feasibility stage of development.DIAMONDS IN CANADAWorld Diamond ProductionCommercial diamond mining commenced in earnest with the discovery of the Kimberley diamondfields in South Africa in the late 1800s, and this resulted in a dramatic increase in the supply of diamonds. As can be seen from figure 1, world diamond production, mainly from South Africa, Angola, Congo, and Namibia, remained relatively constant through the early 1900s until the development of the large Russian kimberlite pipes in the 1950s. Production increased again in the 1960s and 70s with the development of the Botswana mines, but the most significant increase in global production came from the Argyle mine in Australia, which came on stream in 1983 and produced a peak of almost 43 million carats in 1994, representing approximately 40% of the world market. Production from Argyle has since fallen-off as grades have declined and the strip ratio has increased with the deepening of the open pit."

Jan 1, 2003

By Alexander Filotti, Richard Kalson

"In the last decade, the construction industry has witnessed significant changes in the project delivery systems and contractual relationships between the general contractors (GC) and Deep Foundation Specialty Contractors. The Deep Foundation industry, especially including industry specialty subcontractors, have experienced a significant increase in requests that project risks be transferred through contract documents to subcontractors and suppliers with a decrease in margins for the industry. GCs regularly revise their form subcontracts to take into account recent experiences/contractual trends and newly issued judicial precedent, an exercise that is less frequently undertaken by subcontractors and suppliers. These contradictory trends are at the base of the ethical analysis of subcontracts that comprises the subject matter of this paper. Using contracts as a risk management tool in order to mitigate the general contractor’s risks in the context of dynamic changes in the legislative environment will also be addressed. Furthermore, another possibility for risk mitigation for the industry is to actively promote the introduction of the latest technical developments into the contract documents.CONTRACTS’ ETHICSFor thousands of years, ethics have been a constant presence in our lives and have been debated by different branches of philosophy. In modern times, ethics in business started to be an imperative for the success of a globalized economy.“Ethics are standards by which one should act based on values. Values are code beliefs such as duty, honor, and integrity that motivate attitudes and actions.” (Rumbaugh 2004). Some of these values and actions have been carved in legislation in general and in business legislation in particular. More and more, unethical business practices (e.g., corruption) are identified as the root cause of poverty, underdevelopment, and war around the world. In the context of contract ethics, three aspects are of interest:•,Ethics of contract construction•,Ethics of contracting processes•,Ethics of risk allocation in contracts"

Jan 1, 2016

By J. M. Ortiz, J. Haas, W. Kracht, G. Pamparana

This work explores the effect of ore hardness variability on the design of a solar photovoltaic system with battery storage and grid backup, to operate a semi-autogenous grinding mill (SAG). First, a case of two synthetic ore populations was studied, without any consideration of spatial distribution. The mean and variance of the ore hardness (measured in specific energy consumption, SEC) of both populations were subjected to a sensitivity analysis. The operation was evaluated with one and two stockpiles. The latter allows classifying according to ore hardness as a way to adapt the SAG energy consumption to the solar cycle. The results show that using two stockpiles allows achieving a larger autonomy (i.e. less energy imports) at lower total costs, especially when the difference of mean hardness between the two populations is large. The difference in variance (between the two populations) has a smaller impact on the design recommendations. Second, a case study was performed considering the spatial distribution of geometallurgical units. Two cases were considered: (a) brownfield, when there is historical information of the actual variability of the ore hardness; and (b) greenfield, when the system design relies mainly on geometallurgical modeling. Brownfield and greenfield planning result in similar sizing recommendations of the solar power plant, if precise drill cores are available. In this case, geometallurgical modeling is an effective tool for forecasting the energy demand necessary for designing the power plant.

Jan 1, 2018

By ALFREDO INTZAUGARAT, MIGUEL BERRO

During the years 1943 through 1945, there was a decrease in the total oil production in Argentina. In the fields of Comodoro Rivadavia (Chubut Territory) and Mendoza and Salta Provinces, the production obtained was as shown in Table I. The only place where there was a small increase was Plaza Huincul, in the Neuquen Territory and Lunlunta, in the Mendoza Province.

Jan 1, 1946

By P. P. Gregory

The rate of drilling operations in the West Texas district during 1940 was approximately equal to that of 1939. The total number of wells dillled in the area during the year was 1834, of which 1716 were completed as oil producers, 12 were gas wells and 106 were dry holes. The number of wildcat wells drilled during the year was comparatively small. The drilling of inside locations in proven areas and the drilling of wells for the purpose of extending the productive limits in producing fields constituted the bulk of development during 1940. Gaines County led all other counties in the district in the total number of oil-well completions. The oil production totaled 83,345,381 bbl., the highest figure for any year since proration was begun. The 1940 oil production exceeded the 1939 production by approximately four million barrels. Discoveries While comparatively few new oil-producing areas were discovered during 1940, it appears that the oil production found in simpson lime in the Abell field, pecos County, was an outstanding discovery for the year. This was the second Ordovician discovery in Pecos County. Taubert, McKee & Siemoneit located its discovery well, V. W. Crockett No. 1, set. 4 1/2 H. & T. C. R.R, co, survey in the Imperial area of northwestern Pecos County. The top of pay was encountered at 5270 ft., and the well was bottomed at 5357 ft. in simpson lime, on act. 17, I940. The initial production was 928 bbl. of 43" gravity sweet oil in 11 hr. 23 min., flowing naturally through 2-in. tubing with gas-oil ratio of 783 cu. ft. per barrel. Following the completion of the discovery well, large blocks of land were leased in the area, and several locations were made toward the close of the year. There is every indication that the Abell field will become a major producing field in the West Texas district. There was no pipe-line outlet for the field at the end of the year. Shipley-Silurian field, discovered by the Gulf Oil Corporation, appears to be another major addition to the oil reserves in 1940. The discovery well, Wristen Brothers No. 5, is in sec. 18, block 5, H. & T. C. R.R. Co. survey in Ward County. The well was drilled to a total depth of 9187 ft. and was plugged back to 7075 ft. The Silurian lime section was acidized with 3000 gal., from 6993 to 7075 ft., and on Dec. 5, 1940, the well was completed for initial production of 3040 bbl- of 32.2" gravity oil in 24 hr., flowing through tubing. Todd Deep field, Crockett County, was discovered by the Continental Oil Co. et al. The discovery well, J. S. Todd No. 2, set. 29, block WX1 G.C. & S.F. R.R. Co. survey, was completed on April 3, 1940. The top of pay was encountered at 5623 ft., and the well was bottomed at 5691 ft. for initial production of 1613 bbl. of 40.6' gravity oil flowing naturally through 2-in. tubing. The pay section was found in Strawn lime of Pennsylvanian age. There were six producing wells in the field at the end of the year. This appears to be another major discovery in 1940. There was no pipe-line outlet in the field at the end of the

Jan 1, 1941

By P. P. Gregory

The rate of drilling operations in the West Texas district during 1940 was approximately equal to that of 1939. The total number of wells dillled in the area during the year was 1834, of which 1716 were completed as oil producers, 12 were gas wells and 106 were dry holes. The number of wildcat wells drilled during the year was comparatively small. The drilling of inside locations in proven areas and the drilling of wells for the purpose of extending the productive limits in producing fields constituted the bulk of development during 1940. Gaines County led all other counties in the district in the total number of oil-well completions. The oil production totaled 83,345,381 bbl., the highest figure for any year since proration was begun. The 1940 oil production exceeded the 1939 production by approximately four million barrels. Discoveries While comparatively few new oil-producing areas were discovered during 1940, it appears that the oil production found in simpson lime in the Abell field, pecos County, was an outstanding discovery for the year. This was the second Ordovician discovery in Pecos County. Taubert, McKee & Siemoneit located its discovery well, V. W. Crockett No. 1, set. 4 1/2 H. & T. C. R.R, co, survey in the Imperial area of northwestern Pecos County. The top of pay was encountered at 5270 ft., and the well was bottomed at 5357 ft. in simpson lime, on act. 17, I940. The initial production was 928 bbl. of 43" gravity sweet oil in 11 hr. 23 min., flowing naturally through 2-in. tubing with gas-oil ratio of 783 cu. ft. per barrel. Following the completion of the discovery well, large blocks of land were leased in the area, and several locations were made toward the close of the year. There is every indication that the Abell field will become a major producing field in the West Texas district. There was no pipe-line outlet for the field at the end of the year. Shipley-Silurian field, discovered by the Gulf Oil Corporation, appears to be another major addition to the oil reserves in 1940. The discovery well, Wristen Brothers No. 5, is in sec. 18, block 5, H. & T. C. R.R. Co. survey in Ward County. The well was drilled to a total depth of 9187 ft. and was plugged back to 7075 ft. The Silurian lime section was acidized with 3000 gal., from 6993 to 7075 ft., and on Dec. 5, 1940, the well was completed for initial production of 3040 bbl- of 32.2" gravity oil in 24 hr., flowing through tubing. Todd Deep field, Crockett County, was discovered by the Continental Oil Co. et al. The discovery well, J. S. Todd No. 2, set. 29, block WX1 G.C. & S.F. R.R. Co. survey, was completed on April 3, 1940. The top of pay was encountered at 5623 ft., and the well was bottomed at 5691 ft. for initial production of 1613 bbl. of 40.6' gravity oil flowing naturally through 2-in. tubing. The pay section was found in Strawn lime of Pennsylvanian age. There were six producing wells in the field at the end of the year. This appears to be another major discovery in 1940. There was no pipe-line outlet in the field at the end of the

Jan 1, 1941

By Norm Kirk, Robert Bittner

"The addition of a new powerhouse at the existing Tulloch Hydroelectric site on the Stanislaus River in the western foothills of the Sierras Nevada Mountains of central California required a deep excavation in rock on the downstream face of the dam. A cofferdam (water exclusion device) was necessary to isolate the powerhouse construction site excavation from the existing Goodwin Reservoir and the turbulent discharge from the existing powerhouse. The cofferdam was positioned on a steeply sloping fractured rock surface exceeding 50 degrees.This paper describes the challenges encountered during design and construction of the cofferdam and describes the unique design features used to address these challenges including:•,The use of flat-sheet-piles to form cellular walls on the steeply sloping rock surface.•,The use of 5-ft deep tremie concrete plugs in the bottom of the sheet pocket cells to create the bottom seal of the cellular cofferdam walls against the sloping rock surface.•,The use of vertical post-tensioned rock anchors to provide shear resistance at the contact point between the base of the cellular-wall and the sloping rocksurface.INTRODUCTIONModification or expansion of existing hydroelectric power plants often require downstream cofferdams or water exclusion devices to temporarily separate new construction from turbulent downstream discharge of the existing dam. Most dams are positioned on solid rock in the narrowest and therefore the steepest section of the river. This combination of steeply slopingrock and the need for an exclusion barrier creates a challenge for the design engineer trying to maintain a safe dewatered construction site. Typical cofferdam solutions for hydroelectric dams usually use large granular filled circular sheet pile cells that perform as gravity structures. However, this type of structures is not well suited to steeply-sloping highly irregular rock surfaces in a confined area."

Jan 1, 2017

By W. E. Threlkeld, J. A. Treacy, L. J. Stewart, J. C. Ruckmick

The Mustang Draw sulfur deposit is developed in a dolomite reef complex in the Permian San Andres Formation on the eastern margin of the Midland basin in Glasscock County, Texas. Interpretation of the genesis is dependent upon coincidence of a NE-trending fault system with the NW- trending reef complex. The reefs, reef talus, and oolites contained up to 30% interstitial anhydrite. It is indicated that artesian ground waters, hydrocarbons, and bacteria circulated into the reef complex along the fault zone. Bacterial consumption of hydrocarbons and anhydrite created extensive porosity, permeability, and deposition of sulfur in vugs and cavities, and along fractures in the dolomite.

Jan 1, 1992

By J. J. Sammarco

Illumination is essential for mine safety because miners depend most heavily on visual cues to detect hazards associated with slips/trips/falls and powered haulage. The National Institute for Occupational Safety and Health (NIOSH) is conducting mine illumination research to improve miner safety by enhancing a miner?s ability to see mine hazards. Thus far, 16 papers have been published covering diverse topics such as cap lamps, machine-mounted lighting, glare, lighting maintenance, and light-emitting diode (LED) technology issues. NIOSH has also developed an LED cap lamp, LED area lighting, and a Visual Warning System (VWS). This paper provides an overview of the improvements from NIOSH-developed lighting that include: 94% faster trip hazard detection with the NIOSH LED cap lamp; 79% faster peripheral motion detection to detect pinning/striking hazards; no increase in glare; 71% faster machine movement hazard detection with the VWS. Current research is described concerning an LED cap lamp for metal/nonmetal miners, illumination for refuge alternative deployment and inspection, and whether lighting could be used to improve miner escape and rescue in smoke. Lastly, future possibilities of using lighting to improve miner safety are described.

Feb 27, 2013

By Larry A. Haas

A major problem encountered in dump leaching operations is the plugging of both the dump and the piping by precipitated iron compounds. Bureau of Mines research to obtain basic data on agitation leaching and dump leaching methods has shown that the addition of organic chelating reagents can significantly enhance the lixiviant permeability through the ore and the concentration of the metal values in the liquor. For example, the addition of 5 giL citric acid (CA) to a conventional sulfuric acid lixiviant almost doubled the fluid flow rate through 5-cm-diameter laboratory columns containing copper ore. After 185 h of per-colation leaching, the metal concentrations with (and without, in parentheses) CA were 1.7 (1.5) giL Cu, 200 (70) ppm Mn, 160 (40) ppm AI, and 6 (3) ppm Co. The enhancement of metal concentrations with chelating reagents such as CA was confirmed by determining the solubil-ity of several metal ions as functions of pH and chelating reagent con-centration. When ferric ions became insoluble at pH values above 3, the concentrations of other ions also decreased. The addition of che-lating reagents kept iron, as well as the other dissolved metals, in solution even at pH values as high as 5. Citric acid was a more effective chelating reagent than gluconic acid, oxalic acid, or sodium lignin sulfonate.

Jan 1, 1985

By R. Erpelding

High Pressure Grinding Rolls (HPGR) are said to be a good option in new grinding circuits. Due to their low energy consumption compared to other grinding systems such as SAG milling, there is a strong incentive to check their behaviour for certain ore types. With rising energy prices the operation will become even more beneficial in future. As published in the past, the HPGR is claimed to increase the liberation of the valuable mineral component within an ore. An investigation at the research centre of Polysius was conducted to substantiate the liberation behaviour in finish grinding operations. A pilot scale HPGR test unit (POLYCOM MAGRO) with a roll diameter of 950 mm and processing capacity of 80 t/h was used. Grinding tests were completed with a screen and a two stage drying air separation process (SEPOL). Analysis included standard screen analysis, fractional XRF and modern MLA technology. A technique was developed to oppose the amount of produced slimes (resuming bad flotation) against the positive effect of producing high mass fraction at flotation-easy sizes. The paper shows how effective the use of a dry grinding separation could be in terms of production of mass of liberated metal.

Jan 1, 2012

Roof falls in coal mines typically occur in or around intersections and this has not changed in the last two decades. This research develops an improved scientific understanding of stress distribution and associated failure behavior around 4-way and 3-way coal mine intersections. Three-dimensional numerical analyses were performed to determine factors that influence intersection stability. The analyses used Hoek-Brown failure criterion. Failure zones around 3-way and 4-way intersections were developed. Intersection span and horizontal stress have a major influence on intersection stability. For the 4-way intersection, pillar corners across the intersection fail first and lead to progressive failure of immediate roof and floor layers. The mechanism of failure is similar for the 3-way entry but the shape and extension of failed zones differ. Coal ribs mostly fail due to tensile stress, while roof and floor strata fail due to shear stresses. Rib corners fail due to a combination of shear and tensile stresses. In addition to stress distribution; safety factor contours analysis was performed to assess stability of intersections.

Feb 27, 2013

By David Minson

On many occasions, operators have seen that high density and paste thickener performance does not meet the initial design expectations, and the installed equipment produces lower than expected thickener underflow solids content. This lower-density tailings slurry leads to more water and lower beaching angles being seen at the tailings storage facility (TSF). This not only reduces storage capacity, but also increases the risks of non-compliance with environmental permit constraints. Reasons for the shortfall in performance can be many, but perhaps the main problem is inadequate understanding of the critical components of thickener design and operation, with too much reliance placed on standardised design terminology; such as tph/m2. This paper discusses additional factors that influence high-density thickener operation and presents test work that defines “Dynamic Slurry Fluidity”, “Bed Compaction Rates”, and “Natural Slump Angles” for these high yield stress/viscosity slurries. Finally, the paper uses this data to define thickener geometry, drive torque, floor slope(s), rake blade configuration and how this can be used to provide engineers with more tools for in depth evaluation of a High-Density thickener design. INTRODUCTION Generally copper mines are high tonnage operations, with copper flotation concentrators producing high volumes of tailings slurries of milled solids and water. As a result, Tailings Storage Facilities (TSF) become very large and this, along with potential scarcity of water, favours a design that maximises storage space. In theory, the use of filtration equipment that achieves immediate water recovery, high TSF in-situ densities and high stacking angles are preferred for this duty. However, large tailings filter units are uncommon, and have high operating and capital costs that favour the use of thickeners. The use of high-density thickeners to produce a thick or near-paste like slurry with high un- sheared yield stress values above 100 Pascals, is becoming more common. The higher thickener underflow is required to not only maximise water recirculation within the mill, but to also increase beaching angles, maximise tailings storage capacity and minimise evaporation losses arising from large areas of superficial water. However, the reliability of this equipment is also under scrutiny and there is perhaps a need to better define these designs.

Jan 1, 2019

By D Baas, J Le, R Braun, R Chandramohan, K Hollis, G Lane

The Phu Kham Copper-Gold Operation (Phu Kham) is located in northern Laos, approximately 140 kilometres from the capital, Vientiane. The operation is a producing asset for Australian-based copper and gold producer, PanAust Limited (PanAust) and is operated by Lao-registered company, Phu Bia Mining Limited (Phu Bia Mining). PanAust holds a 90 % interest in Phu Bia Mining. The Government of Laos owns the remaining 10 %.The Phu Kham Operation has recently undergone a series of process improvements to treat the anticipated competent ores scheduled for 2017 and 2018. The operation’s comminution circuit, which comprises a semi-autogenous (SAG) mill and two ball mills, each with 13 megawatts (MW) of installed power, was expected to be SAG mill limited when treating competent basement rock. Ausenco Services Pty Ltd (Ausenco), was engaged to help optimise and enhance the productivity of the Phu Kham comminution circuit over an eight-month period. The work involved participating in and overseeing the redesign of the SAG mill liner systems and developing operational strategies for maximising throughput through to the end of mine life. Ausenco’s comminution optimisation tool, Ausgrind, was used to benchmark and analyse plant data with empirical models, predict circuit performance for varying ore characteristics and evaluate liner wear and predict the life for varying operating parameters. Variances between the actual and the predicted values were assessed in detail to identify missed opportunities, and guiding operating parameters were redefined to maximise throughput and productivity. In combination with the redesigned liner system, optimised process controls for varying ore competencies, and improved operational practices and troubleshooting strategies, increased Phu Kham overall production, exceeding the milling capacity when treating competent ores. CITATION:Chandramohan, R, Braun, R, Lane, G, Hollis, K, Le, J and Baas, D, 2018. SAG mill optimisation and increasing throughput at the Phu Kham Copper-Gold Operation – a success story, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 113–128 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By Amy Anderson

The Silica (SME) Technology has been utilized on three separate projects focusing upon the stabilization of mercury-contaminated materials: at the Mother Lode Mine in Oregon, the Sulfur Bank Mercury Mine in California and at a former chloralkali plant in British Columbia. Each of the projects relied primarily on the results collected via EPA Method 1311 TCLP, with additional tests such as SPLP, humidity cell tests and other supporting tests employed as well. Both technical and economic performance of the silica-based technology was evaluated as well as that of competing technologies in some cases. Results established that in each of the three projects an SME chemical dosage rate of 3% chemical by weight of soil/sludge was the optimal ratio required to achieve project treatment objectives, TCLP test results exhibited a reduction in the leachable mercury from the treated materials ranging between 75% and 99% as compared to untreated material, satisfying the technical objectives for each project, Project costs ranged from $l5.00 - $18.26 per metric ton.

Jan 1, 2003