Search Documents

By E. H. Timmerman, A. F. van Everdingen, J. J. McMahon

The prevent paper contains a method which combines the material balance equation' with the water influx equation' to obtain reliable values for the active oil originally in place and a quantitative evaluation of the cumulative water influx. The method is illustrated by an application to a reservoir without original gas cap. In the absence of an original gas cap. results may be obtained using only field production and pressure data, PVT analyses. and a minimum of subsurface information. CHARACTERISTICS OF RESERVOIR AND RESERVOIR FLUIDS Production in the field under review is obtained from the top of the Wilcox formation of Eocene age, at a depth of approximately 8,100 ft subsea. The structural map, Fig. 1, shows that the accumulation, half elliptical in shape with the long axis in east-west direction, is trapped to the north and on the upthrown side of a normal fault. A number of east-west faults with additional minor faulting in random directions are found in the general area, and seismic information and production performance indicate in this particular case the existence of a second fault a short distance downdip, with a strike more or less parallel to the fault controlling the accumulation. It is estimated that 1,830 acres were originally underlain by oil and that the maximum thickness of the original oil column, about 37 ft, was only slightly greater than the maximum thickness of the oil-bearing sand. Maximum net sand thickness was estimated at approximately 26 ft. From logging and subsurface information the gross sand volume has been placed at 37.400 acre-ft. which reduces to about 27,500 acre-ft after probable non-productive intervals have been deducted. The following table presents laboratory analyse; data for the Wilcox sand cores. Average Average Samples Considered Permeability Porosity All Samples 236 md ..19.9percent Samples with k>l md 256 md 20.5 per cent Samples with k>8 md 275 md 20.9 per cent Interstitial water was estimated at 15 per cent. The initial gas-oil ratio was approximately 900 cu ft/bbl. and the initial shrinkage factor was determined by the laboratory to

Jan 1, 1953

"Health standards in the U.S. are among the highest in the world. Achieving these standards have often had an impact on productivity, slowing output, and raising prices to levels that make it difficult to compete with many foreign industries. The answer to many of these problems lies in the development of new and advanced control techniques. This overview has identified some of the major respirable dust technological hurdles that have been overcome, and provided some insight into current and future approaches underway to remove these obstacles and to provide the United States with the most advanced state-of-the-art mining industry in the world from a respirable dust standpoint. The necessary developmental research is costly and time-consuming. The long-term, high-risk aspects of this effort are being addressed by the Bureau and the Generic Center on Respirable Dust, with support by industry. This should be recognized as one of the principal agents through which the great mineral potential of this Nation can be realized, and our international status as a mining power be assured without compromising the health and welfare of those who ensure it.The problem of more stringent dust standards will continue to grow. To date, approximately 40 pct of the coal mining industry has been placed on more stringent dust standards due to quartz. Control techniques must be improved if mandated levels are to be met. As longwall production increases, dust levels will also increase. In light of the industry trend toward longwall mining, if no new control technology is available, the Federal dust standard will act as a constraint on future output per hour. The Bureau has recently completed a survey of 18 coal preparation plants; 50 pct of these operate at dust levels which exceed 2.0 mg/m3; future work will be directed toward solutions in this area. The 2.0 mg standard for respirable dust is for dust particles which are below 10 pm in diameter. Recent studies have shown that dust in the range between 10 and 25 pm can cause obstructive airway disease. The Bureau is currently determining the extent of exposure to dust in this size range from various mining operations."

Nov 1, 1988

By M. Laframboise, M. Buarzaiga

High-pressure acid leaching (HPAL) of nickel laterites has received considerable attention in recent years. High paymetals extraction, good selectivity, and advances in pressure hydrometallurgical technology are some of the reasons for this interest. Falconbridge Limited (Sudbury. Ontario) investigated the HPAL process using both fresh water and seawater for ore processing. The use of seawater resulted in a chloride concentration of 7.8 g/L in the autoclave feed. A test program was developed to study the effect of process water and leach temperature on the leaching behaviour of different ore compositions from the Koniambo deposit in New Caledonia. The work showed that salinity has a major effect on autoclave chemistry. This paper explores the results.

Jan 1, 2004

By Xinyang Yu

The flotation of diaspore, kaolinite, pyrophyllite, illite and the diaspore-kaolinite mixture were studied with a new cationic organosilicon quaternary ammonium collector entitled QAS222. The acting mechanism of the collector with the four minerals was analyzed by Zeta potential measurement and FT-IR spectrum analysis. The results indicate that the QAS222 was effective in the reverse flotation of the diaspore-bauxite mixture of different Al2O3 -to-SiO2 mass ratios (A/S ratio) at an optimum pulp pH of 11. The potentials of the four minerals increased when they were conditioned in the QAS222 solution; however, the potentials of the three aluminosilicate minerals increased faster than that of the diaspore, especially at pH>9. Furthermore, they were positive in a wide pH range, indicating that QAS222 has a strong adsorption on the surface of the aluminosilicate minerals and thus that these minerals can be floated. The FT-IR spectra analysis further indicates that, besides electrostatic adsorp-tions, formation of the hydrogen bond and ammonium absorptions, chemical adsorptions occur between QAS222 and the aluminosilicate minerals, which allow for the QAS222 to be strongly adsorbed on the aluminosilicate minerals. However, these reactions between QAS222 and diaspore at pulp pH=11 are weaker than those of the aluminosilicate minerals. Thus, surface adsorptions cannot be formed effectively, resulting in reduced floatability.

Jan 1, 2010

By Wolf-R. Under

For improvement of urban traffic infrastructure, the City of Amsterdam is cur­rently constructing the 9.5 km long North-South Metro line passing through the central districts of Amsterdam. Focal section of the project is the Central Station linking the NS Line with the Central Railway Station, the East Metro line, new bus and tramway terminals, ferries and individual traffic. Construction works required for the project are of high complexity and technical standards. They are executed under severe restrictions concerning programming, space, logistics, and impact on the integrity of existing buildings and structures as all existing installations and facilities have to maintain fully operational during the construction period. The paper deals with the main geotechnical features of the project and in particular with the diaphragm wall and bored pile construction at the Voor-plein and the De Ruijterkade sections of the Central Station.

Jan 1, 2006

By R. J. Colony

DEPOSITS of iron are widely scattered in the folded Cretaceous rocks and the associated igneous intrusives of Puerto Rico. Most of them are too small for commercial development, but a few have aroused some scientific and economic interest, among them the large body of residua] limonite at the west end of the island near Mayaguez1-6 (Fig. 1) and the mixed hematite and magnetite deposit on the southern slopes of the Sierra de Cayey, about four miles north of Arroyo.7-9 Neither of these orebodies has been developed, nor have investigations of the widely distributed deposits of magnetite, which include all the remaining occurrences of iron deserving of economic consideration, proceeded beyond the exploratory stage. With the possible exception of the mixed deposit near Arroyo, the magnetite is directly associated with andesitic and dioritic intrusives, which invade the Cretaceous rock section, and the bulk of it, occurring in calcareous sediments, is clearly of contact-replacement origin. The small deposit on Rio Portugues, north of Ponce, is found in a limestone band near its contact with an andesite dike.10,11 Two deposits of unde-

Jan 1, 1935

By P. H. Davenport

"The ore-element patterns in regional lake sediment geochemical survey data from four areas of Newfoundland containing granite-related mineralization reveal characteristics which can be used to identify mineralized granitoids. The St. Lawrence Granite with its fluorite deposits, the Ackley Granite with molybdenite mineralization, the Grey River tungsten lodes and the newly discovered Mo- W mineralization at Granite Lake, Central Newfoundland, have all been included in the regional lake sediment geochemical surveys, which now cover about 90,000 km2 of the Island of Newfoundland. The lake sediments over these mineralized granites show diagnostically high values of Mo, F, Pb, Zn and, in three of the four cases, U, together with locally high Ag and Cu values. Furthermore, these ore-metals display a distinctive zoning pattern about the intrusives, which can be related to the classical ore-metal zoning patterns developed about many types of mineralized granitoids.IntroductionGranitoids in Eastern Canada are receiving renewed interest as potential hosts of tin, tungsten, uranium and related mineralization. Although a number of mineral deposits and showings have been known from a few granites (sensu lato) in the region for many years, granites had generally received little attention as potential hosts of metallic mineralization until the recent resurgence in interest in the mineral potential of these rocks. In Newfoundland, where granitoid rocks underlie about 30070 of the land area, petrologic data are available from some granites, particularly those in eastern Newfoundland (Strong et al., 1974; Strong, 1980), but in southern and southwestern Newfoundland the data base is sparse, and indeed in many cases individual plutons are not delineated on the geological maps of the area . Most of the available data on Newfoundland graniotolds have been summarized by Strong (1980), who gives a general assessment of their mineral potential by comparing their physical, mineralogical and petrochemical attributes with mineralized granites elsewhere in the world."

Jan 1, 1982

By S. Arthur Krom

(Wilkes-Barre meeting, June, 1911.) RECENT experiments indicate that the usual type of concentrating-table is not only poorly adapted to produce the desired results, but also is based upon an incorrect principle, namely, the use of riffles to perform the work of stratifying the various minerals. We have heard a good deal about riffles for concentrating-tables; exhaustive experiments have been made to discover the proper form of riffle, or to prove the superiority this or that form; disputes and patent-litigation have arisen over the matter of riffles, and thus many have been led to believe that the riffle is the saving-device upon which the process of concentration depends. In the present paper it is proposed to show that the riffle is greatly overrated as to the part it performs in the concentration of minerals, and that, in the near future, it may possibly be eliminated entirely from that process. The experiments in question have shown that the troublesome riffle can be considered of secondary importance at the most, and should be so classed in the construction of a concentrating-table built upon the right lines. The action of any form of riffle on a concentrating-table is such as to upset and retard the process of settling and stratifying the various minerals on the table-deck. From the deck of a riffled table no concentrates can be delivered until the deck is "bedded," that is, until a sufficient amount of metallic values have been fed to the table to spread over a large portion of the deck, forming a substratum of the heavier minerals. This substratum must be maintained by the feed within quite narrow limits, and directly proportional to the rate of discharge from the table, in order that the bed shall not be lost. On the other hand, the riffles having a very lim-

Jul 1, 1911

By A. C. Richardson

The mine of the Porter Coal Co. is located at the town of Porter in the northwestern part of Jefferson, County, Ala., about 20 miles west of Birmingham. The operations in this mine are confined to the middle and bottom benches of the Mary Lee bed. The coal from the Porter mine is handpicked and washed before being placed on the market. The handpicked lump coal and the washed egg and nut, coal are sold chiefly as domestic and steam-raising fuel. The coal finer than 1 inch is washed in 2-compartment jigs and utilized in the manufacture of metallurgical coke. The coal company has found that, when coal ranging in size from 1 to 0 inch is washed in jigs, a considerable amount of high-ash material finer than 3/16 inch remains in the washed coal. This paper gives the results of an investigation which was conducted for the purpose of determining the washing characteristics of the through 316-inch raw coal and the extent to which the ash might be reduced by means of coal-washing tables. This investigation has been made in connection with an. extensive study of the coal-washing problems now being conducted by the United States Bureau of Mines and the University of Alabama, with the cooperation of the coal-mining companies of the State.

Jan 1, 1933

By V. T. McLemore

In-situ leaching (ISL) operations have been proposed to recover uranium from sandstone-uranium deposits in NM. ISL (also known as in-situ recovery, solution mining, solution-leach mining, leach mining) consists of injecting a leaching solution into the mineralized zone through injection wells. The leach solution migrates through the formation, dissolves uranium and is recovered through production wells. The uranium is then precipitated through a conventional uranium recovery system. Several criteria must be met in order for in-situ leaching to be successful, most important is that the ore body must be amenable to chemical leaching. A number of ISL operations have been conducted in NM in the past (Mobil, Crownpoint; UNC-Teton, Section 23; Grace Nuclear, Hook?s Ranch, Seboyeta, Church Rock; Anaconda, Windwhip). Kerr-McGee (later Quivera Mining Co., Rio Algum) successfully produced uranium from mine-water recovery (recirculated mine water) from the Ambrosia Lake mines (mid-1960s to 2002). Despite some difficulties, ISL is a viable alternative to recovering uranium and could be utilized in the Grants district with proper aquifer characterization and monitoring.

Jan 1, 2009

By Homor N. McDonald, G. Dale Coe, Will H. Coghill

"INTRODUCTION Sporadic beneficiation tests have been made on the Birmingham (Ala.) red iron ores for the last 55 years. Now, gravity-concentration plants are in operation, of tables are in use. A major problem, as seen by the present writers, is to obtain a coarser concentrate and add to the recovery without increasing the quantity of slime. The oily practicable solution found so far is to recover, by means of concentration (hydraulic) classifiers, the coarse concentrate normally lost in the table middling and, by a similar method, to recover middling particles from the table tailings The size and shape of the coarse concentrate Particles combine to cause them to report in the table middling rather than in the table concentrate. Similarly, mineral is lost in the tailing. Because of this, the nature of the ore, the deportment jerking table, plant tests on classifiers and tables, and the suitability of small concentration classifiers to treat table zonal middlings are discussed herein.The work was done by the Southern Experiment Station, Bureau of Mines, in cooperation with the University of Alabama, Tuscaloosa, Ala."

Jan 1, 1935

By Piotr Kozlowski, Stanley L. Worst, Matthew J. Niermann

The Waterman Hospital in Tavares, Florida was undergoing an expansion and required a below-grade excavation immediately adjacent to the Emergency Department. This wing of the hospital was under high traffic and required uninterrupted access for ambulances as well as helicopter landings. The below-grade expansion was also next to a part of the hospital which did not have a basement. Tiedback soldier beams and wood lagging were used as the earth retention system where the shoring line was not immediately adjacent to the existing structure. Structural jet grout underpinning was used to support the existing building and to serve as the earth retention system in the more sensitive area. Jet grout underpinning was chosen to minimize movements, loss of ground and settlement of the structure which was bearing on clean sand deposits. This paper will discuss the design, quality control and construction of jet grouting and its application to this project. INTRODUCTION Project Background The expansion of the Waterman Hospital included an addition to the Emergency Department. This addition was located adjacent to the existing hospital building in a congested area with limited access. The north side of the addition was bordered by the ambulance drop-off area. The south side of the addition was bordered by the helipad landing area. Both areas had to remain open and fully accessible 24 hours a day, 7 days a week.

Jan 1, 2019

By T. Salman

Most authorities agree that the dissolution of gold from an ore takes place according to the Elsner equation first stated in 1846. The main requirements for the dissolution reaction to proceed are:(1) that the gold be clean.(2) that the gold be exposed to the solution.(3) that the cyanide solution be active, i.e., not over loaded with impurities which could retard or inhibit the reaction.(4) that an adequate supply of oxygen be available (from air).When the above conditions are met, cyanidation becomes basically a mechanical operation.Minerals such as quartz, calcium carbonate are relatively inert to cyanide though they may give rise to mechanical troubles. Most ores present an assortment of chemical problems, depending upon the constituent present, which react to the solution to varying degrees. It should be borne in mind that minerals which are disturbing to the operation, though present in small amounts, usually exceed the weight of the gold by several hundred times. In addition, the application of flotation and other forms of concentration to gold ores, previous to cyanidation, concentrates not only the gold, but also the other heavy minerals and these complicate the chemistry of the process.

Jan 1, 1975

By B. G. Stone

"INTRODUCTION “Sampling is the process of taking a small portion of an article such that the consistency of the portion shall be representative of the whole” (Baxter and Parks, 1939) “An orebody is a mixture of minerals in proportions that vary in different parts of the mass. As a consequence the proportion of contained metals also varies from place to place. Therefore, a single sample taken in any particular place would not contain the same proportion of metals as does the orebody as a whole except by a highly improbable coincidence. The probable error, which would be very large if only one sample were taken, decreases with the number of samples, but it never disappears completely unless the samples are so numerous and so large that their aggregate is equal to the orebody itself, in which case the orebody would be completely used up in the process of sampling. Since carrying sampling to such an extreme would defeat its own purpose, some probable error is always present in actual cases and the practical objective is to reduce this probable error to allowable limits. This means balancing the number of samples against the desired accuracy; if there are not enough samples the result is unreliable; if there are too many, the time and expense of taking them is excessive.” (McKinstry, et al., 1948). In an actual orebody, the accuracy of sampling depends not alone on the number of samples but also on proper distribution of them throughout the orebody, for it would obviously be incorrect to take all of the samples either in a rich part or a lean part. Therefore it is important to select the places in such a way that all parts of the orebody will be represented. “For those who cultivate land which is alike arid, heavy , and barren, and in which they sow seeds, do not make so great a harvest as those who cultivate a fertile and mellow soil and sow their grain in that. And since by far the greater number of miners are unskilled rather than skilled in the art, it follows that mining is a profitable occupation to very few men, and a source of loss to many more.” (Georgius Agricola page 5 Book 1 as translated by H.C. Hoover and Lou Henry Hoover, 1950)“It is evident that mining is very profitable to those who give it care and attention”"

Jan 1, 2015

By Hillis R

As part of BHP Iron Ore's policy and goal of achieving a high standard of environmental management within its operations, a protocol for mine closure has evolved. The need to demonstrate sound environmental management with respect to site decommissioning meant that a comprehensive, environmentally sensitive closure protocol was required. Within this framework, a four-phase protocol was developed, the first phase was the determination of objectives in relation to site rehabilitation and end land use. The second phase was the determination of the process required to achieve these objectives. The third phase was the application of this process in a site specific manner. The fourth and final phase was monitoring of the site with regard to the achievement of determined objectives. The protocol was originally developed to direct the closure and decommissioning of the Goldsworthy site in 1992. This being the first total site decommissioning for BHP Iron Ore. Since that time the protocol has been successfully utilised for the closure of the Yampi (Koolan Island) operations (in 1993/94) and the Shay Gap/Nimingarra Operations (in 1994/95).

Jan 1, 1996

By D. J. Briggs

The use of backfill for regional and local support is receiving increasing attention in the South African mining industry. To ensure that fill materials meet the purposes for which they are intended, a test procedure to characterize the load-deformation characteristics for a particular fill was developed. The major variables identified as influencing the load-bearing proper- ties of backfill include particle size distribution, porosity, width-to-height ratio, strain rate, confinement, water content, and additives. The influence of these variables on the performance of backfill is described in relation to crushed waste, dewatered tailings and deslimed tailings. These investigations confirmed that no single test could be used to define the overall stress-strain behaviour of a selected fill. Nevertheless, resulting from this work, a preliminary standard test procedure for uncemented backfill materials, com- prising a suite of tests in unconfined and confined compression, has been formulated. This test procedure is a significant advance towards a more meaningful evaluation of fill materials. Test results will also provide numerical information for input use in computer programs for the design of mine layouts incorporating backfill.

Jan 1, 1988

By William H. Mount

INTRODUCTION The requirements of mine ventilation demand the constant attention of the mine operator. Just as the physical mine structure changes with time, the ventilation requirements of a particular mine change considerably from season to season and even from day to day. No ventilation system can remain adequate indefinitely; and all systems require monitoring and adjustments to achieve proper ventilation. Instead of being given fore- thought and planning, mine-ventilation systems too of- ten are erected hastily, merely to correct an already un- healthy situation. The usual result is an inefficient and costly system that, in some instances, may prove in- effective in providing fresh air to the point of need. The ventilation of mines is a combination of both art and science. The fluid that must be moved is in- visible; its properties change drastically with temperature, barometric pressure, and humidity; and the methods of measurement are not precise. In part, ventilation engineering must rely upon the art of good industrial ventilation experience and sometimes even the trial-and- error method. However, the properties of air can be determined with relatively inexpensive equipment; with some care, measurement accuracies within 5% of the actual values can be obtained. Thus the art of ventilation gradually is being supplanted by improved engineering practices. Although the direction of flow and the volume may not be predicted correctly by airflow equations in every situation, it is better to try to predict the behavior of a given ventilation before installation than to proceed blindly with a system design. When used with the discretion that comes from education and experience, the basic laws of ventilation can provide sub-stantial insight into the design of an air-handling system; and they can prevent wasteful or even dangerous designs from being installed. Since the mine operators who read this text will have varying amounts of exposure to ventilation theory, the basic laws of airflow and of mechanical ventilation are presented in the first section. The emphasis has been placed on the interpretation and use of fan characteristic curves that are supplied by fan manufacturers. Considerable information can be obtained from these fan curves, particularly when they are used with a graphic model of the mine, drift, or duct in which the fan or fans are to be installed. A few minutes spent comparing the various characteristic curves can help the designer obtain the correct fan for the job. However, the under- standing of a few fundamentals is necessary; and this text has been prepared to provide ample and understandable information in a "how-to" style. In subsequent sections of this text, more down-to- earth subjects will be covered, including the problems of air recirculation, relative merits of installing fans in series or in parallel, expected maintenance requirements (vibration, lubrication intervals, etc.), fan noise and some remedies, effect of an inlet bell on the fan per- formance, basic air-measurement techniques and equipment, and similar miscellaneous items. Although this text is not intended to be a comprehensive bible of mine ventilation, it has been prepared as a guide that provides some useful information to individuals responsible for the quality of the underground environment. Every person working underground is en- titled to the safest environment that can be provided within the limitations of existing technology and at a reasonable cost. Adequate ventilation is well within both limits, provided that the system is designed intelligently, in conjunction with the mining plan, and not as an after-

Jan 1, 1982

By A Romanel, M S. Kato, M P. Piermatei, P Artioli

"Brazil is the sixth worldwide producer of aluminum and Votorantim (Metals) has been operating three bauxite open pit mines in a particular way of working. In those the deposits occur on the top of hills, under forest, coffee, eucalyptus plantation or pasture area.The deposits are not large and normally mining takes an average of two months to be completed before starting the rehabilitation process, which demands a good strategy in mining planning to achieve the production goals.The benefit function developed to select feasible areas uses, beyond production costs, fees from the owner by using their area and rehabilitation cost. Both are based on land use and occupation field survey data. In this process each area with different land use receives a specific rehabilitation cost as input into a block model.Once the selection is made the mining schedule begins, taking into consideration the following premise: the orebody needs to be mined in a short period of time because during this time, the surface owners receive from Votorantim a compensation based on the expected profits from their plantation or pasture, plus royalties related to the ore amount existing in their area.Not all operations have waste dumps. Waste is pushed down by bulldozers to the lower part of the ore border. After loading and transporting ore, the waste is handled back to the mined area to fit the topography. With this step concluded, the mined area is directed to the environmental team who, alongside university partners, develop land reclamation to return them to their owners, eg in 2011, 110 ha were rehabilitated of which 29 per cent is native forest.Votorantim closes many mined areas a year and currently the entire mine planning considers this particular way of operation, making profit with minimum interference with the community and the environment.CITATION:Artioli, P, Kato, M S, Romanel, A and Piermatei, M P, 2012. Environmental variables at bauxite mine, in Proceedings Life-of-Mine 2012 , pp 171-178 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jul 10, 2012

By E. R. Maize

This report is the third of a series on convergence of roof and floor in coal mines and subsidence of surface that accompanies it. The first papery dealt with extraction in a mechanized mine (Montour 10) having relatively short rib lines that retreat rapidly. The second 6/ dealt with extraction in a mine (Crucible) in which coal was loaded by hand and in which the rib lines were long and slow-moving. The present report deals with a mine (Gibson) in which conditions approximated those in the Crucible mine, except that the distance between room centers was considerably less and the pillars were narrower in consequence. Moreover, the average cover was less and the studies were made under the steep hillside of a stream valley compared with a gently rolling surface over the portions of the second mine studied. Gibson mine lies in the east-central part of Washington County, Pa., approximately midway between the Montour 10 and Crucible mines on a north-south line. A cooperative agreement covering the work was made with the Hillman Coal & Coke Co. through W. L. Affelder, vice president. This paper describes the methods used in the investigation, gives excerpts from the data obtained, and offers such generalisations as appear to be justified.

Jan 1, 1940

By H. R. Coles

Test work conducted in the 6.4 and 10.52 m Aerofall Mills at the Iron Ore Company of Canada Carol Project showed that the conventionally used ?deflector?-type liners which form the basic principle of Aerofall Mill grinding did not necessarily provide the best grinding performance. A new design, using low profile liners incorporating radial ribs of a proper height, actually improved the mill throughput in the order of 9 to 20% without sacrificing grinding efficiency. In addition, the new design reduced liner weight and scrap losses, which resulted in a reduction of liner consumption by 25%. It provided better protection to the mill shell and reduced the overall maintenance cost for the mill

Jan 1, 1980