Search Documents

By Simon E. Rodriguez

This paper presents sulfur isotope data obtained for the deposits and country rocks of the Bailadores and Aroa Mining District, Venezuela. The study is a part of an extensive geochemical investigation of the mineralized belts that has as their aim the elucidation of the genesis of ores. The Bailadores deposits are located at about 600 Km. west-southwest of Caracas, or about 10 Km. southeast of the Town of Bailadores, Merida State (Fig. 1). The mine concession is held by the Ministry of Mines and Hydrocarbons (De Lima I, De Lima II and La Cascade areas). In a straight distance the mine is about 90 Km. southwest of Merida, the capital of Mérida State. From Mérida to Bailadores, through La Victoria and Tovar, it takes 3 hour by car. From Bailadores to the mine site it is about 40 minutes by jeep. The Aroa deposits are located at 4 Km. east of Aroa Village, Yaracuy State, about 220 Km. west of Caracas. It is 83 Km. from San Felipe, the capital of Yaracuy State to the mine (Fig.2). The mine is about 600 m above sea level, situated on the northern foot of the E-W trending Andes. The topography of the mine are shows a mature stage and is somewhat rugged. As the climate is warm and humid, the area is thicky covered with jungle.

Jan 1, 1974

By D. G. Westlake, D. T. Peterson

The saturation solubility of thorium dihydride in thorium was studied by saturation of samples and subsequent analysis. The solubility increased from about 1 at. pct at 300°C to above 20 at. pct at 800 °C. Over this temperature range the log of the solubility was a linear function of the reciprocal absolute temperature for thorium of good purity. The heat of solution of thorium dihydride was found to be 7.9 kcal per atom of hydrogen in crystal bar thorium and 6.6 kcal per atom of hydrogen in Ames thorium, The important effect of hydrogen on the physical and mechanical properties of many metals is receiving increasing recognition. The basic physical and chemical data necessary to help explain the observed effects of hydrogen on the mechanical proper ties of metals are all too often not available. The solubility of hydrogen in thorium metal was determined to provide a portion of this basic data for the thorium-hydrogen system. The absorption of hydrogen by thorium metal and the formation of thorium hydrides was studied by several investigators, beginning in 1891, and their work is summarized in Gmelin's Handbuch.1 No effort was made to determine the extent of solid solubility in the metal in these early investigations and the impure metal available made interpretation of the results uncertain. Nottorf2 reported the results of a careful study of pressure-composition isotherms for the thorium-hydrogen system. The principal interest in this work was in the composition and dissociation pressures of the thorium hydrides. Mallett and campbel13 reported the pressure-composition isotherms for the thorium-hydrogen system up to the composition of thorium dihydride. The saturation solubility of thorium dihydride in thorium was reported to be 13 at. pct at 650°C and 23 at. pct at about 900° C. Mallett and Campbell used thorium metal which had been prepared by the calcium reduction of thorium tetra-fluoride or thorium oxide. The results obtained with thorium of these two types agreed within the experimental error. PROCEDURE AND MATERIALS Procedure—The method used to determine the solubility was to saturate a sample of thorium with hydrogen and analyze a portion of the saturated sample. This method was chosen rather than a determination of pressure-composition isotherms since it was much less time consuming and could be applied at temperatures at which the equilibrium hydrogen pressure was too low to measure. The

Jan 1, 1960

By G. H. Gilman

The campaign now being waged to improve the quality of the rock-drill bit is the natural outcome of the scientific development of the drilling machine during the past twenty years. In this development there has been a great increase of power output per unit of weight of machine. But the development of the rock drilling engine has been seriously hampered by the need of a drill bit that would withstand, without undue wear or breakage, the heavy rapid blows of the improved pneumatic hammer. This problem was difficult to solve because an increase in the weight or section of the drill-steel bar resulted in decreased cutting speed and higher operating costs of both the bit and its actuating engine. The solution, therefore, is to make the bit of steel that, for a given weight or section, will be more shock and wear resisting. In the attempt to meet these requirements, many of the drill-steel manufacturers alloyed the steel with vanadium, chromium, nickel, etc. on the assumption that such elements would improve the rock-drill bit but due to the sensitiveness of such steel to forging and heat treatment, higher cost, and lack of continuity of effort on the part of the steel manufacturer to perfect this product, but little progress has been made in the adoption of these steels and the so-called straight carbon steel is today recognized as the standard material for all rock-drill bits. The first step in improving drill-bit efficiency is the determination of the cause of breakage and wear. For this reason, in 1917, certain rock-drill manufacturers, in conjunction with some of the larger mining interests, conducted exhaustive tests in both the field and the laboratory. It was then found that, in the main, the cause of drill-steel troubles is not attributable to the duty imposed upon it by the normal operation of the drilling engine, but to improper forging and heat treating of the bit and to the subjecting of the bit to improper use. The fact that it is possible to minimize the troubles attributable to improper heat treatment of the drill steel has been demonstrated and it is recommended that such knowledge be made available by teaching those interested in the production, use, and up-keep of drill bits the principles on which success in this direction may be achieved. Unfortunately, but little attention has been given to the education of the drill smith. But a few years ago, the instructions given the man

Jan 1, 1922

By J. J. Lander, L. H. Germer

MOLYBDENUM and tungsten have desirable corrosion and temperature resistant properties, but the metals in bulk are expensive and their fabrication is difficult. Such considerations led to a search for a method of plating them upon base metals. This search was successful and led furthermore to a number of developments which could not have been foreseen. Neither pure tungsten nor pure molybdenum has been electroplated successfully, although the literature of electroplating is liberally sprinkled with the description of unsuccessful attempts. The process of plating these metals by thermal reduction of their halides has achieved only limited usefulness because of technical limitations and because of limited range of product quality. Plating by thermal decomposition of the carbonyls does not suffer from limitations of the same sort and the properties of the plate are readily controllable. This paper describes the plating of molybdenum and tungsten, and of compounds and alloys of these metals, by pyrolysis of their carbonyl vapors. Chromium also has been plated in this manner, but the experiments upon chromium have been less extensive and the results much less satisfactory. Probably the most important of the products which we have obtained are the alloys with carbon, and the carbides of the metals. Either molybdenum or tungsten can be deposited upon a base metal as a coherent and adherent coating. By adjusting the plating condition the carbon content of the coating can be made to have any value from substantially zero to about 35 atomic pct. The hardness is dependent primarily upon the amount of carbon in the plate and can be regulated over a very wide range, some coatings containing considerable carbon being harder than sapphire. In addition to products already known this method of plating has yielded new carbides of molybdenum and tungsten and alloys supersaturated with carbon. These new products are possible because, in the process of plating, carbonyl can be decomposed at temperatures as low as about 150'C, and thus in the presence of other substances reactions occur which could perhaps not be produced in any other way. In addition to carbides and alloys with carbon, sulphides and oxides of molybdenum and tungsten have been produced and studied. There are certain other advantages of the carbonyl method of plating. It is not required that the base have good electrical conductivity as in electrochemical processes, and the base need not have the temperature stability required in plating from a halide. Thus low melting glasses, as well as other ceramics, can be plated almost as readily as metals. In particular, the plating of glass with

Jan 1, 1947

By J. Luo

A major design problem for upper seam longwall gate roads that are to be constructed in a multi-seam environment is to predict the effects of stress field changes created by interaction. To quantify these effects, case study data were analyzed to develop empirical stress transfer relationships between seams for both longwall and room and pillar mining. Data analysis showed vertical movement and roof characterization in the upper seam to be controlling factors in damage prediction and, therefore, gate road planning and design. CMRR (Coal Mine Roof Rating) was correlated with the multi-seam roof characterization systems previously used. A WINDOWS-based software package named UGLY (Upperseam Gateroad Longwall Stability) was developed. Results from selected case studies were correlated with upper seam stress predictions.

Jan 1, 1997

By Ben L. Seegmiller

INTRODUCTION Site characterization using oriented borehole core is the subject of this paper. Borehole core is a standard source of data for rock mechanics investigations. Oriented borehole core provides data whereby the geometric orientation of various geologic discontinuities (faults, joints, bedding, etc.) may be determined. The orientation and strength characteristics of discontinuities are important in many engineering investigations and in particular, in slope stability analyses. In heavily vegetated or soil covered situations, oriented borehole core may provide the only means of assessing the subsurface planes of weakness which characterize the site. The purpose of this paper is to briefly describe various methods or orienting core, core characteristics which may be logged and the methods of processing and using the data for site characterization.

Jan 1, 1977

By P. H. Brace, N. A. Ziegler

THE study of the relations between gases and metals is one of perennial interest to all who are connected with the production of high-grade metallurgical products. The data reported here are the outcome of work of which the object is to determine the effects of dissolved gases upon the properties of metals and to gain a more detailed knowledge of the reactions between gases and molten metals, particularly iron, under definitely controlled conditions. We have attempted to reduce our margin of error by dealing with relatively large quantities of metal, from 4 to 13 lb. (2 to 6 kg.), and keeping the ratio of refractories to metal as small as practicable. The ingots produced are large enough to provide adequate material for making determinations of magnetic and other physical properties. In choosing the bell-jar type of furnace we were influenced by the results of considerable experimentation along the same general line which indicated that, for the scale on which we were to work, it was important to have the furnace structure independent of the vacuum enclosure. The use of a bell-jar surrounding the entire furnace accomplishes this and also gives great freedom of observation during operation and ready accessibility for the replacements which are necessary after each run. Our choice of analytical method was made in the light of the results secured by H. M. Ryder, who used a method similar in principle for the analysis of very small quantities of gas extracted from strips of metal heated electrically in high vacuum. We have presented some selected preliminary experimental data as being illustrative of the quantity and nature of the gases which occur in iron of different origins, but do not urge any hypothesis at this time. THE FURNACE Our furnace may be described as "a high-frequency induction furnace of the bell-jar type." It is similar in a general way to that described by Cain and Peterson' though we have introduced certain refinements of

Jan 1, 1928

By J. E. Burke, C. W. Mason

IN attempting to study precipitation from a tetragonal lattice using solid solutions of bismuth in tin, it was found that although a Widnmanstatten pattern is observed 1 only a qualitative analysis of the orientation relationships is possible, because of the unusual structural changes that accompany the precipitation process MICROSCOPICAL STUDIES Alloys were made from Chempur tin (Standard samples 42b and 42c, National Bureau of Standards), and bismuth (Kahlbaum C P ) by melting neighed quantities together under palm oil, stirring well, and casting in a heated graphite mold The polishing and etching techniques employed largely govern the visibility of the structural changes The preliminary surfacing operations were similar to those recommended by Villela and Bergekoff,5 through BehrManning 3/o abrasive papers, lubricated by a solution of paraffin in kerosene A rough metallographic polish was next given, using a thin cotton cloth charged with relevigated alumina (maximum particle size of about 4µ) and soap solution, repeated etching and polishing served to remove disturbed metal For high-power examination better preparation was necessary It was found that on such soft metals the threads of the fabric, rather than the abrasive, cause most of the scratching Cotton outing flannel, which had been brushed so that the nap lay down, was fairly satisfactory, but a Heavy grade of silk velvet (not the noncrushable kind) was found to be better, especially after some use A better procedure was as follows The metal lap was warmed slightly, and a 4-in circle of woolen broadcloth was cemented to its center by a thin film of melted paraffin The broadcloth was then moistened with water, and a 30 to 40 per cent solution of sodium hydroxide heated to about 50°C was poured over it, allowed to stand for 1 to 2 min and then washed off It was neither necessary nor desirable to remove all the sodium hydroxide from the cloth, since its etching action aided in the removal of the flowed layer from the sample The cloth was then charged with a paste of the relevigated alumina in water Since this lap did not remove deep scratches, it was necessary previously to polish the specimen on some material such as the silk velvet The sodium hydroxide softens and partly gelatinizes the woolen lap covering, permitting a scratch-free polish, but its action continues, and the cloth deteriorates after about 24 hr This is not serious, because a new lap can be prepared in about 5 min, and only small pieces of cloth are used Etching with a strongly acid solution of ferric chloride was found satisfactory for removing the flowed layer For the final etching, the most satisfactory reagent was that of Taffs,7 the formula for which is FeC13 6H20, 2 grams, HC1, 5 c c , H2O, 30 c c , C2H5OH (95 per cent), 60 c c This etchant reveals differences in com-

Jan 1, 1941

By George W. King

The yield strength of a dispersion-hardened W-3.8 vol pct Tho,alloy, in both the recovered and recrys-tallized condition, was investigated and cornpared with that ofrecrystallized pure tungsten over the temperature range of 325" to 2400°C. It is deduced that the Orowan mechanism is obeyed in the recrystallized alloy. In the recovered alloy, a further enhancement of the yield strength results from the retained substructure which is stable up to temperatures in excess of 2700°C. Temperature and strain rate cycling tests were also performed, and the apparent activation energy for the deformation process was derived. This activation energy, - 3 ev, for the recovered and also the recrystallized alloy was about the same as that for re crystallized pure tungsten. However, the activation volume of the recovered alloy, -10-2 cu cm, was about an order of magnitude lower than that of the recrystallized alloy or pure tungsten. This fact accounts for an enhancement oj- the temperature dependence of the yield stress of the recovered alloy. A dislocation velocity exponent of about 4 to 13 was deduced frorn the strain rate cycling tests , which is in good agreement with values reported for tungsten single crystals. VARIOUS theories have been developed to explain the enhanced yield strength of a metal containing a dispersed second phase of small hard particles. These theories are thoroughly reviewed by Kelly and Nicholson.' The theoretical models can be separated into two types. The first type assumes direct interactions between moving dislocations and dispersoids. One of the most widely investigated models for this mechanism is the bowing out of dislocations between the dis-persoids and their subsequent pinching off in order to bypass the obstacles. This is the well-known Orowan mechanism.' The second type is an indirect effect of the dispersion because of its ability to stabilize to high temperatures the substructure introduced by cold working. In this instance, the increment in the yield strength is expected to be inversely proportional to the square root of the subgrain diameter. In the present work, a quantitative study was made of the strengthening effect caused by a thoria dispersion in a recrystallized W-3.8 vol pct Thoz alloy over the temperature range 325" to 2400°C. The results are compared with the increment predicted for the Orowan mechanism based on the calculations by ~shb~.~ In addition, the alloy was tested in the recovered state so that any additional strengthening resulting from the substructure produced during fabrication could be measured. The respective contributions can be separated in this manner, provided that the particle size distribution of the dispersion remains the same in both the work-hardened and the recrystallized state. Particle size distribution measurements showed that this condition was met in the present work. I) EXPERIMENTAL PROCEDURES A) Material Production and Fabrication. The alloy investigated is essentially the same as that reported much earlier by ~effries,~ who also found the strength of tungsten to be improved by the thoria dispersion. The procedure for producing the alloy consisted of mechanically blending a thorium nitrate solution in proper concentration with tungsten oxide (WO3) powder, followed by hydrogen reduction to metal powder. After reduction, the dispersed second phase is present as thoria (Thoz). The pure tungsten powder used for comparison was produced in the same manner except that the thoria doping step was omitted. The powders were consolidated by cold pressing and self-resistance sintering in hydrogen. The resulting ingot had a cross section about 0.6 sq in. and a density about 93 pct of theoretical. The ingot was swaged to 0.174-in.-diam rod at temperatures varying from 1650°C initially to -1200°C near final rod sizes. Two intermediate recrystallization anneals were employed during fabrication. Analysis of the swaged rods is reported in Table I. B) Electron Microscopy Techniques. Carbon extraction rrPxcas prepared by a technique reported by ~00' were used to quantitatively evaluate the thoria particle size and distribution. Electron nlicrographs of extraction replicas were taken at 20,000 times but were then enlarged two to three times in printing. The areas photographed were randomly selected. A Zeiss Particle Size Analyzer (Model TGZ3) was used to count and measure the sizes of all particles present on the print. About three thousand particles were counted in determining a distribution curve. Electron transmission microscopy was used to determine the effect of annealing on the substructures of the materials. Thin foils were produced by a two-stage thinning process. The rods were first ground on emery paper to ribbons about 10 mils thick and then a jet of 5 pct KOH was used to electrolytically reduce a portion of the cross section of the ribbon. Final perforation was achieved by immersing the specimen in a 5 pct KOH solution and electrolytically polishing at a current density of about 0.3 amp cm-'. The foils were examined with a Hitachi HU-11A electron microscope. C) Tensile Testing. Tensile testing was performed in an Instron Testing Machine equipped with a radiation-type vacuum furnace which operates at about 1O"S torr at temperatures as high as 2400 °C. The same furnace was used for annealing the tensile specimens.

Jan 1, 1970

A review of historic mining information and geological literature pertaining to the Alpine Mine, Lyell Goldfield has been completed. As a result of this work the Alpine reef is inferred to be associated with an upright anticline with a sub-horizontal axis. Structural profiles prepared from limited underground data indicate that the reef is subparallel to the eastern limb of the anticline and cuts across the western limb. Reassessment of structural mapping completed by the New Zealand Geological Survey indicates that Greenland Group metasediments within the Lyell Goldfield are folded into a series of opposed assymetic folds with sub-horizontal axes. It is suggested that the anticline which harbours the Alpine Reef is located on the axis of a synclinorium. Along the western limb of the synclinorium the subsidiary folds have steep west dipping limbs and shallow east dipping limbs (western sense of assymmetry) whereas shallow west dips and steep east dips are typical of the eastern limb. The notion of quartz mineralisation occupying the axis of a synclinorium is contrary to the situation in the Reefton Goldfield where quartz mineralisation is affiliated with folds associated with an anticlinorium. Historic mine data reveals that below No.4 Level the quartz-gold mineralisation, in the Alpine Mine, occupied a steeply dipping ore channel. The strike of the channel was to the northwest and within this structure the are shoots plunged to the north at approximately 40¦. Archival mine plans show that two quartz bodies, the North and South Blocks, were present at No. 4 Level. Although the North Block was followed down to No 14 Level (530 m vertically below the surface outcrop) the South Block was only mined as far as No 7 Level. Sampling on No 7 Level together with the results of trial mining suggest that the grade of quartz underfoot in South Block is low. Information from the Mines Statements and mapping undertaken by the Gold Prospecting Scheme reveals that faulting had a profound influence on the intregity and extent of the Alpine Reef. The reef occupies a Inajor shear zone but little is known about it. It is also apparent that below No 7 Level the reef was progressively shattered by faulting and this may be the chief reason for the decrease in grade in the lower levels of the mine. No substantive facts are available about wall rock alteration effects adjacent to the Alpine Reef Still this is not surprising considering that comments on the mineralised pug envelope and breccias adjacent to the mined quartz shoots at the Globe - Progress Prospect were omitted from contemporary publications. In spite of this the existance of sulphide bearing reef casing lithologies cannot be completely dismissed since 9.15 m of 'reef track' has been reported in Reids No 2 Level.

Jan 1, 1996

By Qingshou Chen, Gongbo Li, Hengqian Ran

A method for safe fracture of rock, concrete and other brittle solid material using dynamic water pressure by explosion is provided. The propagation of the pressure is studied with Allievi water hammer theory. Wave equation and velocity formulas of the pressure propagation are shown. The dynamic water pressure is tested in the lab. The propagation of the pressure is simulated by MMIC-2D. The results of fracturing rock in the lab and on a quarry are presented.

Jan 1, 2000

By Nath S. Parate

With the extension of mining beneath residential and industrial areas, it is becoming increasingly necessary to extract coal and minerals in such a way that subsidence damage due to groundmovement is reduced to a minimum. Understanding clearly of the mechanism of subsidence development is a must in view of the environmental problems and the energy crisis today. This paper gives a simple analysis of various components resulting from subsidence and the influence of other factors on their development. An up-to-date review of the subsidence and strain profiles is presented, with particular references to the coal mining operations. The importance of this topic from mining damage to structures, buildings properties and environment in mining areas is undeniable. Field results are discussed.

Jan 1, 1982

By Gilbert P. Moore

Production in the Argentine in 1930 amounted to 1,415,099.7 metric tons, which converted into barrels of 42 gal., using the factor of 6.29, amounts to 8,909,773 bbl. This is a decrease of 481,613 bbl. from the 1929 production, which was 9,391,386 bbl. The production for 1930 was divided among three fields, as shown in Table 1. Table 2 covers Table 1.—Argentine Oil Production, 1930, by Fields Barrels Comodoro Rivadauia District Government........................................... 4,547,670 Railways Co........................................... 1,314,358 Astra-Eastern......................................... 1,016,024 Anglo-Persian......................................... 365,021 Solano Co............................................. 24,613 Dutch Shell........................................... 6,963 7,274,649 Neuquen District Government........................................... 569,245 Standard Oil-Argentina................................. 659,551 Astra-Eastern......................................... 8,234 Challaco Co. (Sol)...................................... 121,598 1,358,628 Salta District Government........................................... 90,576 Standard Oil-Argentina.................................. 185,920 276,496 8,909,773

Jan 1, 1931

Of the world's total production of gold the largest proportion comes from the more regularly consistent ore bodies, but in the aggregate an important part comes from those which are often irregular, uncertain and small. These smaller ore bodies are often high in grade and, as the capital required to work them is not large, they appeal to people seeking a quick and profitable return for a small outlay.These small mining concerns cannot afford detailed geological and petrological investigations and mapping, so they are very often dependent on local knowledge and experience which admittedly may be of really great value.Nevertheless the absence of skilled guidance may not only cause good opportunities for intelligent exploration to be lost, but discourage the seach for other ore bodies.lVIining engineers in the course of their travels in the examination of mines often come across such cases and also others where problems of finding lost ore bodies have been solved by the man on the spot. As records of cases are valuable and useful additions to the knowledge of ore occurrences, the writer now proposes to describe one such case coming under his observation in recent years.It is that of a small mine, known as the Idaho, at the southern end of the famous "Golden Mile" at Kalgoorlie (see Fig. 1). This mine has been a small and very erratic producer ever since it was abandoned by an English company which owned it forty years ago. Except for one period of four years it has always been owned and worked by parties of co-operative miners and during its time has gone through a tortuous career. Although it has often...

Jan 1, 1938

By A. Quilodran, B. Jakovljevic, T. McCallum, P. Wong

"Rare earth separation by solvent extraction (SX) requires multiple separation plants each consisting of many extract, scrub, and strip stages to separate the individual metals. SX modeling advances have brought benefits to circuit design and process optimization by quickly narrowing test conditions without the need for exhaustive laboratory studies. Modeling can be used to optimize circuit configuration, O/A ratios, and acidities, which allows for CAPEX and OPEX savings. A comparison between pilot plant data and the results expected from modeling is presented for rare earth separations with CYANEX® 572.INTRODUCTIONRare earth separations can be difficult due to limited separation between the elements (Xie, Zhang, Dreisinger, & Doyle, 2014). This requires relatively complex solvent extraction circuits utilizing multiple extract, scrub, and strip stages as well as multiple SX configurations to achieve the desired metal purities. Designing rare earth circuits can be complex, and significant time and testing may be necessary to determine the required staging and optimal conditions.Circuit modeling for rare earth separations has been introduced to the industry using CYANEX® 572 extractant (Soderstrom, McCallum, Jakovljevic, & Quilodran, 2014). CYANEX® 572 is an acidic organophosphorus extractant formulation which has a weaker ligand-metal complex strength than that of the traditionally used phosphonic acid extractants. This allows efficient extraction while requiring a significantly lower acid concentration for stripping (Wang, Li, Zhao, Dong, & Sun, 2015). The reduced acid requirement in strip is expected to provide OPEX savings.The modeling can be utilized to quickly determine the required acidity and organic/aqueous (O/A) ratio for a given separation. It is also expected to reduce CAPEX requirements as optimal staging can be determined, and implemented.CYANEX® 572, combined with modeling, was utilized to produce a purified dysprosium (Dy) stream. To achieve this separation, multiple SX circuits were designed and operational conditions specified to separate Dy from the mixed rare earth chloride feed."

Jan 1, 2016

By P. S. Capper

"Generally speaking, the most intensive efforts at dust control in the mining industry have, in the past, been concerned with underground operations and where uranium ore or high silica material is processed. In the past several years, Stoop Rock has made Intensive efforts to reduce dust levels in it's Iron ore pelletizing complex. There have been no great engineering break-throughs with regard to dust control in such plants, and certainly no new engineering techniques have had to be applied at Steep Rock. This paper deals with how significant improvements in dust levels have been achieved through minor modification to dust collectors and ventilation units, improvements in operating practices, and education of supervisors and hourly personnel.PROCESS DESCRIPTIONSteep Rock Iron Mines is located 120 miles west of Thunder Bay near Atikokan. (fig. 1) Run-of-mine ore is pelletized along with some -1"" concentrate that has been processed in the concentrator (a summer operation only), which utilizes gravity separation to upgrade a mechanical mixture of ore and waste."

Jan 1, 1976

By John R. Shattuck

As a part of the general chromite investigation in California designed to aid In the production of chromite during the recent war emergency, the Bureau of Mines explored the Coggins property in Siskiyou County, Work by the Bureau in cooperation with the Federal Geological Survey began in October 1942 and was concluded in March 1943. This report presents a brief history of the mine, outlines the physical features of the district, describes the deposits) and explains the work completed by the Bureau of Mines, Table 1 shows the analysis of diamond drill-hole samples. The logs of drill holes are in the appendix.

Jan 1, 1949

By J. F. Childs

Montana consists of an Archean crystalline basement overlain by Proterozoic through Cenozoic sedimentary rocks. Igneous rocks range in age from Archean to Pleistocene; the most voluminous magmatism and volcanism occurred during the Late Cretaceous and early Tertiary. The state can be divided into three tectonic provinces whose deformational styles are a function of different bedrock responses to Late Cretaceous-early Eocene compressional tectonism. Several long-lived structural zones have been periodically reactivated since the Precambrian, and were the sites of recurrent magmatism. Regional gold distributions are strongly influenced by the tectonic provinces and structural zones. Lode gold systems in Montana occur in diverse geologic settings resulting from a complex interaction between structure, magmatism, and sedimentary depositional processes. Reserves or resources are known for 19 significant lode gold systems, and additional unannounced discoveries have been made recently. Mineralization ranges in age from Archean to Tertiary. The influence of long-lived structures is apparent at both the regional and deposit scale, and in some cases multiple mineralizing events have been superimposed upon one another. Most Montana gold systems have a direct spatial and genetic association with Late Cretaceous through Oligocene igneous rocks. However, the importance of sedimentary rocks and associated depositional processes should not be underestimated.

Jan 1, 1993

By Franklin D. Slagle

Porosity and bulk-and sand-grain-density values were determined for 2,040 core samples of 30 formations from 47 wells in New York, Ohio, Pennsylvania, and West Virginia, and are compiled for petroleum industry use in well-log evaluation and geologic studies.

Jan 1, 1967

With the inauguration of Petroleum Technology this year, and approval by the Board to add an Assistant Secretary to the New York staff to serve the Petroleum and Coal Divisions, the Petroleum Division looks forward to greater opportunities and responsibilities. An improved medium of publication offers further incentive to engineers and investigators in the oil industry to make contributions. The authorization by the Board of Directors of a new Assistant Secretary is an appreciation of the splendid contributions made to the industry by the open forum of the Petroleum Division. It is also a recognition of the possibilities of greater service to the membership along the lines established ten to fifteen years ago by DeGolyer, Fohs, Ambrose and Lovejoy, to mention a few leaders. It isexpected that the new officer will spend a substantial part of his time in the field, visiting the student sections, the respective Divisions, helping in the arrangement of papers and Section meetings and intensifying interest in the Institute. The Petroleum Division will hold three meetings this year. The Fall Meetings will be held on Oct. 6 and 7 in San Antonio and on Oct. 20 and 21 in Los Angeles. The programs for these meetings will deal chiefly with engineering research and production engineering problems. Papers on production statistics and general economics of the industry are reserved for the Annual Meeting in New York. The annual production symposium and statistics are accepted as standard for the industry. With continuously deeper penetration into the earth in search for and exploitation of petroleum, it is necessary to have a better understanding of reservoir conditions and to place more phases of the operation under engineering control. Among the subjects relating to reservoir conditions tha thave been proposed for the fall meeting programs are phase equilibria at high pressures, interfacial tension between oil and water, the flow of oil and water through sands, the chemistry of films and underground temperatures. Investigations relating to control of operations include methods of continuously logging while drilling both visually and electrically, methods of studying drilling samples, properties of drilling fluids, improved cementing practices for isolating thin sands under high-temperature conditions and gas conservation, particularly production from high-pressure reservoirs. Additional suggestions of general themes or individual subjects will be welcomed, since it is desirable to build a backlog of material for Petroleum Technology. 9

Jan 1, 1938