Search Documents

By Christian B. Woods, Joe C. Drumheller

"Kenneth A. Huber, P.E., Langan Engineering & Environmental Services, New York, New York, USAThe dream to bring New Jersey Devils hockey to the largest city in New Jersey became a reality in the summer of 2005, when construction began for the Prudential Center in downtown Newark. The Prudential Center site encompasses an entire city block that had a varied history of uses ranging from a cemetery in the late 18th century, to a rail yard and train station for the now-defunct Central Jersey Rail Road in the 19th and early 20th centuries, to commercial development in the latter half of the 20th century. Each of these prior uses presented challenges to the design and construction of the Prudential Center that required innovative engineering solutions, including: archaeological investigation and exhumation of the former cemetery occupants, protection of historic buildings surrounding the site, and extensive demolition to remove old train bridge foundations.The design team was required to develop potential foundation systems for the arena. Several foundation concepts were evaluated for cost and constructability, including: driven piles, drilled shafts, and shallow foundations on improved subgrade. Following a detailed cost analysis and value engineering exercise, the decision was made to support the arena on spread footings following the completion of a multi-phased ground improvement program consisting of a combination of dynamic compaction and removal and replacement. To evaluate achievable allowable bearing pressure as part of the design, a dynamic compaction test section was performed within the building footprint prior to the start of production work; this resulted in an increase of the allowable design bearing pressure from 2 tons per square foot (tsf) to 3 tsf. This reduced the expected foundation costs by 30% and gained sufficient time in the schedule to allow for the completion of the arena in time for the New Jersey Devils 2007- 2008 hockey season.BACKGROUNDThe dream to bring New Jersey Devils hockey to the largest city in New Jersey became a reality in the summer of 2005, when construction began for the Prudential Center in downtown Newark. After several years of negotiating between the City of Newark, local landowners, area developers, and the Devils themselves, a deal was finally struck to erect Newark Arena, now known as the Prudential Center, right next to City Hall. This is not to say, however, that once the site location was finalized, that no further challenges were encountered in the construction of Newark’s new crown jewel."

Jan 1, 2015

By F. W. Liang

The geology of pearl River estuary belongs in strong weathered rock quaternary geological systen, so the conditions are complication. Since 80's we built the first deepwater wharf of Shenzhen chiwan port which has 3 berths of 10000 dwt, We have built 3 berths for vessels of 40000 dwt both in Shekou Port and Chiwan port. The berths for carriers of 10000 dwt in Yantian Port of Dapeng Bay are constructing now. In the five years, We built more than 20 deepwater berths of 5000 dwt to 40000 dwt. This paper will introduce how to solve the difficulties of the complex geological conditions and how to use the new fashion construction. We will reduce the period of engineering construction and get good quality and make a good beginning of rapid development of port construction in ShenZhen Special Economic Zone.

Jan 1, 1991

By Kane, M O&apos

The mineralised members of the Brockman Iron Formation mined at Mt Whaleback are overlain and underlain by shale horizons. To maximise resource recovery, waste movement within the life of mine plan will total approximately 3.3 billion tonnes. Approximately 15 per cent of waste materials contain zones with varying amounts of sulfides and carbon and are referred to as æreactive shaleÆ. Reactive shale has the potential to self-heat and can react with some explosives, resulting in spontaneous explosion. Sulfide rich zones also have the potential to generate acid rock drainage (ARD). Successful mining of reactive shale requires constant co-ordination between the geology, mine planning, mining and environment departments. Safe storage of reactive shale is the focus of ongoing research. Since the mid-1990s, a number of trials have been undertaken at Mt Whaleback in order to further the understanding of the physical and chemical properties of reactive shale. This paper summarises some of these trials, and discusses key learnings arising from interpretation of results. Ultimately, the learnings from this research will provide the guidelines for successful storage of reactive shale.

Jan 1, 2003

By Robert H. Scott

Developments during the past few years have brought coal-based composite fuels to commercial readiness. During the next few years, composite fuels will become available from a number of suppliers. Potential users must evaluate the combustion properties of these fuels to determine equipment and operating changes required for their use. Most work to date has been done with boiler applications. However, many potential non-boiler applications exist in the metals and minerals industry. These applications require specific evaluations appropriate for the processes involved.

Jan 1, 1982

By S. E. Younis

The mining industry is currently looking to better understand, anticipate, and be able to mitigate business and operational risks in order to deliver the rewards of risk taking, and to minimize the frequency and impact of risk on the downside. Assessing risk works from the premise that the identification and management of existing risks can be very challenging, especially when threats are not easy to detect, the likelihood of occurrence is difficult to gauge, and/or the consequences are uncertain. Some approach this as a ?check the box? task, even though fire and safety incidents continue to occur and investigations often find the hazard analyses did not properly identify the cause or consequence. You cannot engineer protective designs and safeguards for causes and consequences that have not been identified appropriately. For the mining industry, risk management is an important tool for making critical decisions and, in some cases, meeting regulatory requirements. Providing high-quality documentation that meets both regulatory and corporate requirements is critical for maintaining safe, uninterrupted mining operations. Risk management is a five-part process: 1. Identify the hazards and their causes, 2. Determine the hazard consequences, 3. Calculate the frequency of occurrence, 4. Quantify the risk associated with the system, process, or procedure, and 5. Provide feasible solutions for the risks

Jan 1, 2012

By A. G. Storey, J. B. W. Bailey

"The Noranda Process at the Horne Division ofNoranda Mines Limited now smelts approximately 350,000 short dry tons of concentrate a year, which is 40% of the total smelter throughput. Campaigns are averaging 200 days and refractory consumption is much lower than in the conventional smelter.In this paper, details ofrecent operation are given, together with updated projections for operation with higher levels of oxygen enrichment.IntroductionThe Noranda continuous smelting process has been in operation at Noranda, Quebec, for six years and in that time it has smelted a million and a half tons of concentrate. It is currently smelting 1,200 to 1,250 tons per day of concentrate on an instantaneous basis"" and it is handling approximately 40% of the Horne smelter throughput.This paper will describe the current operation of the process and the improvements that have been made since 1976, when the process was described by L.A. Mills et al.lSince early in 1975, a high-grade matte averaging 73% copper has been produced, which is then sent to the converter aisle for final treatment. All the information in this paper refers to the operation of the process in the matte mode .Early in 1978, Kennecott Copper Corporation started up their new smelter near Salt Lake City, Utah , which has three Noranda Process reactors operating with high oxygen enrichment of the tuyere air (2). These furnace s incorporate some design improvements, which will be described briefly."

Jan 1, 1980

By Hood M

Rock cutting excavation technologies and particularly continuous excavation technologies, can offer benefits in the areas of reduced costs, higher revenue and increased safety in a variety of mining situations. Non-explosive rock excavation technologies for example, can deliver significant benefits in the areas of dilution and improved ground support (no overbreak). This paper is an attempt to focus on the development and future of alternative rock breaking technologies and to provide some insights as to why and how we should proceed in this direction. The market size for underground hard rock excavation technologies is examined. A short review of the evolution of various rock excavation technologies in terms of cost and production rate is given and a summary of the state-of-the-art technology is presented. Mechanical excavation technologies (TBM) have very high production rates compared to D&B and the gap is widening, however, they have not been successfully applied to mining applications. Operating costs for mechanical and D&B systems have been dropping over time, however, D&B costs are the lowest. Given the current state of knowledge it appears that with regard to hard rock underground metalliferous mining that R&D efforts should be focussed in the following areas - disc cutter tool development (materials and design; operation; presentation to the rock surface), hybrid cutting systems (consisting of water jets and disc cutters) and development of pressurised hole breakage technologies. It is also possible that two techniques known as the pulsed laser and pulsed water jets may have some potential. The generally agreed specifications for a widely applicable underground hard rock excavating machine are - disc cutter based, a minimum production rate of 100 t/h, be flexible, manoeuvrable and deployable, weight of less than 100 tonnes and be economically competitive with D&B in rocks over 150 MPa UCS. Such a machine would seriously challenge the position of conventional D&B in a wide range applications and provide some of the benefits of mechanisation and automation that the mining industry is pushing so hard for. However, technology developments in the D&B area are not static and hence the target is moving and is increasingly difficult to overtake.

Jan 1, 1995

By R. R. Estill

THE rank of the Ruhr coal ranges from a high volatile bituminous coal to an anthracite, depending to some extent on the original depth of the seam. The average Ruhr coal corresponds to a soft bituminous American coal of a coking quality. The average thicknesses of individual coal seams being mined are also comparable (59 in. against 65 in. in the United States). However, consideration of seam conditions and mining conditions other than those just mentioned emphasizes differences rather than similarities with United States soft coal. In general, the Ruhr seams now being mined are much more folded and inclined than American seams. Dips of 20" and 30" are common in seams now being worked, and 30 pct of the coal reserves in the district are in seams dipping more than 35". Only on the tops and bottoms of folds do we find rather flat coal seams. In addition to the folding there is extensive displacement by cross faulting plus a certain amount of strike faulting of an overthrust nature, which results locally in doubling or omission of seams. Because of the long history of mining in the Ruhr, nearly all coal lying near the surface has long since been mined out, and we find that the average depth of mining is at present about 2300 ft below the surface. Deep mining, folding, and faulting result in seam conditions requiring a great deal more roof support than one finds in American soft coal mines. In fact only in the anthracite district and the Rocky Mountain and Pacific coal fields do we find somewhat similar conditions. It is easy to say, therefore, that the problem of mechanization of coal cutting and loading in the German mines is quite different from that which we have so effectively met in America with our mobile cutters and loaders, duck bill loaders, and a room and pillar system of mining our drift and slope mines.

Jan 12, 1950

By William A. Rhoades

INTRODUCTION Ever since miners were faced with the task of moving ore, some form of scraper has been in use. At first, men and beasts of burden supplied the power to move the scraper, and later, machines were developed for this purpose. In the early 1900s, a few mining properties used small pneumatic single-drum winches to pull loaded scrapers to a raise or ore pocket, and the empty scraper then was dragged back to the muck pile by a miner, as shown in Fig. 1. Just prior to 1920, an improvement was introduced, using two single-drum hoists. As illustrated by Fig. 2, the second hoist was used to return the empty scraper to the muck pile. However, this arrangement still re¬quired two men, one operating each hoist. The next developmental step was to eliminate the second man by locating the hoists side-by-side and using one man to control both hoists. As illustrated by Fig. 3, this involved the use of a tail rope over a sheave to pull the scraper back. The greatest progress in development and the great¬est increase in the use of slusher haulers occurred between 1920 and 1930. In 1921, the Sullivan Machinery Co. designed and built the first two-drum scraper oper¬ating on the principle illustrated by Fig. 4. It was powered by a 4.5-kW (6-hp) Turbinair(r) motor and would pull a 450-kg (1000-1b) load at 0.61 m/s (120 fpm). In 1922, this unit was shipped to the Verona Mining Co. of Caspian, MI, and it experienced immediate success in the Lake Superior iron ore district. Since the two-drum slusher was much less expensive and more efficient than hand mucking, the Lake Superior mines were saved from financial disaster when iron-ore prices fell 25% between 1923 and 1925. Immediately there¬after, a demand developed for slushers that would oper¬ate with electric power, which was considerably cheaper than compressed-air power. In 1923, the Sullivan Machinery Co. responded with the first electric-powered double-drum hoist. During subsequent years, design improvements in¬cluded separate tail-drum gearing to increase the tail¬drum speed, as welt as a number of safety features such as rope guides. One result of these improvements and their utilization by the Michigan iron mines was an in¬crease of 100% in the tons of ore per miner per day in those mines between 1924 and 1929. Since the two-drum slusher was capable only of straight-line mucking, it was not a practical machine for use in open stopes. In 1929, the Sullivan Machinery Co. introduced the first three-drum slusher. As illustrated by Fig. 5, two tail drums and one hauling drum were provided. A tail sheave could be placed at each side of the stope, and the ore then could be loaded and hauled to a central point from the entire width of the stope. During the 1930s, progressively larger slushers were demanded. By 1940, two- and three-drum units were available with motor power as high as 45 kW (60 hp), and slusher power continued to increase after 1940. Be¬tween 1951 and 1952, Joy Manufacturing Co. designed a 112-kW (150-hp) two-drum Blusher for the Climax Molydenum Co. Although there has been no demand for a slusher more powerful than this, 150- to 225-kW (200- to 300-hp) slushers are quite feasible at the pres¬ent time. During the last 30 years, many slusher improvements have been made to the operating life, operational safety, and ease of operation and maintenance. Increased tail-drum speeds have decreased overall scraping times. Rope guards, totally enclosed drums, and operator shields have reduced the hazards of injury due to wire¬rope breakage. Improvements in lubrication have made the slushers relatively maintenance-free, with long operating lives. The introduction of spring-actuated drag brakes prevented uncontrolled unreeling of dis¬engaged drums, allowing the development of practical remote-control slusher operation. Remote control now is available in a choice of all-air, all-electric, or air¬electric slushers. APPLICATIONS Quite simply, slushers are used to load and transport material (ore), generally over a short distance of from

Jan 1, 1982

By H. Biloni, R. Morando

The surface structure and substructure of Al-Cu alloys solidified as conventional ingots and under particular conditions such as those used by Bower and Flemings are studied. The influence of lampblack coating on the mold walls is especially considered and the results compared with those obtained in copper and graphite molds where no coatings exist. When high heat extraction conditions exist the observations show that mechanism of copious nucleation is responsible for most of the chill zone. When the heat extraction through the mold walls is low, a coarse grain structure with dendritic morphology arises, with a size that depends on the degree of convection present, analogous to that analyzed by Bower and Flemings. In both cases the effect of the convection on the macroscopic and microscopic appearance is discussed. The ingot macrostructure consists of one or more of three zones: "chill zone", "columnar zone", and central "equiaxed zone". The mechanism of the columnar-equiaxed transition has been subject of considerable interest and at present at least three theories exist about the formation of the equiaxed region: 1) the constitutional supercooling theory1 maintains that the equiaxed crystals nucleate after the columnar zone has formed, as a result of the constitutional supercooling of the remaining liquid; 2) chalmers2 pointed out, however, that there were several objections to this proposal, and that consideration should be given to the possibility that all the crystals, equiaxed as well as columnar, originated during the initial chilling of the liquid layer in contact with the mold; 3) Jackson et aL3 and O'Hara and ~iller~ suggested that a remelting mechanism of the dendrite arms is responsible for the formation of the equiaxed region. After the work of Cole and Bolling and other authors6 it became evident that convection (natural, reduced, or forced) plays a very important role in the transition from columnar to equiaxed and on the size of the resultant equiaxed structure. Until recently the accepted explanation of the chill zone was that it occurs as a result of copious nucleation in the liquid layer in contact with the mold walls.798 The columnar region is a subsequent result of the growth of favorably oriented grains and, as a result of a selection mechanism studied by Walton and Chalmers,9 elongated grains with marked texture are formed. Recently, however, Bower and Flemings" using an ingenious laboratory experiment introduced the idea that the "copious nucleation" mechanism is not responsible for the formation of the chill zone and that the presence of convection, introducing some form of "crystal multiplication", plays a decisive role in the formation of the chill zone. Unfortunately, it is important to consider that for their conclusions Bower and Flemings extrapolated the results obtained in their special experiments to the case of conventional ingots, and that these authors only analyzed the macrostructures of the specimens. Let us consider the work by Biloni and chalmers" concerning predendritic solidification. These authors were able to show that a study of the segregation substructure of A1-Cu gives information about the nucleation and growth of crystals formed in contact with a cold surface. A spherical predendritic region characterizes the first part of every grain nucleated in contact with the surface as a result of the chill effect. The aim of this paper is to elucidate through the observation of the segregation substructure the conditions under which (in the Bower and Flemings type of experiments and in conventional ingots) either the nucleation or the multiplication mechanism gives rise to the structure in contact with the mold walls. I) EXPERIMENTAL TECHNIQUES The experiments were performed on two alloys: Al-1 wt pct Cu and A1-5 wt pct Cu. The purity of the aluminum was 99.99 pct and the copper 99.999 pct. The results obtained with both alloys were similar. In the Bower and Flemings type of experiments the apparatus employed to obtain rapid solidification against a surface was similar to that used by those authors. The liquid was drawn by partial vacuum into the thin section mold cavity. Plate casts were 5 cm wide and usually 7.5 cm high. The thicknesses of the cast were 0.1 and 0.3 cm. Two different materials were used for the mold, copper and nuclear-grade graphite. The internal mold surfaces were polished and left uncoated for some experiments. In other experiments, the copper or graphite surface was coated with a thin film of lampblack material. In some of these particular experiments one of the mold walls was left with an uncoated region (usually in the form of a cross). The conventional ingots were cast in graphite or copper molds. In different experiments the mold walls were sometimes uncoated or coated with lampblack material. The results obtained in conventional and Bower and Flemings copper molds were compared with those obtained with copper molds coated with a very thin film of graphite; the results obtained were essentially similar. The size of the conventional ingots was 5 cm diam and 7 cm high in all cases. The cast surfaces produced by the Bower and Flemings type of experiments and conventional methods were observed macroscopically and microscopically without any metallographic preparation. As Biloni and Chalmers showed," the observation of the chill surface can give considerable information about the structure and segregation substructure.

Jan 1, 1969

By Joseph Hirschi, Behrooz Abbasi, Harrold Gurley, Yoginder P. Chugh

"The research goal was to assess if analytical tool/s can be developed to quantify displacements around a geological fault as longwall face moves toward it and past it. A company was faced with crossing a 2-3 m (6-10 ft.) normal up-thrown fault in the development entries and the face while mining a 375 m (1,200 ft.) wide longwall face. A field monitoring and numerical modeling study was performed to develop data. Field measurements consisted of roof-to-floor convergence and rectangular rosettes in the immediate roof. Numerical modeling consisted of constructing a 3-D structural model using the FLAC3D software with the fault plane incorporated as ubiquitous joint. Based on analyses and field observations data, the coal company was informed of impending movements along the fault plane and likely impacts on the development entries. Additional stiff supports were installed in head gate entries around the stage loader and equipment about 60 m (200 ft.) outby of the longwall face (solid). As the longwall face approached the fault, predicted displacements were documented and manifested by severe loading on the installed supports.BACKGROUND AND STUDY OVERVIEWThis paper summarizes results of a cooperative study aimed at improving longwall mining operations in Illinois. More specifically, the study focused on: 1) In-mine measurements in development entries while mining ahead of and behind a faulted zone, 2) Making observations on stability of pillars and entries while mining through the fault, and 3) Developing simplified analytical structural models using FLAC3D to assess if predictive techniques can be developed to plan mining operations through fault zone. Available data on geometry of the fault with estimates of the cohesion and frictional parameters were used for modeling."

Jan 1, 2015

By R. X. Li

The overall flow-sheet of producing chromium (III) sulfate is described in this paper. The suitable conditions of each process such as sintering, leaching, aluminum removal, reduction, and de-composition conditions were experimentally studied. The results show it is reasonable to produce chromium (III) sulfate with the flow-sheet pointed out in this research work. The final product is Cr2(SO4)3 solution contained 150~250g/L Cr.

Jan 1, 2014

By J. E. Gill, A. R. Byers

"The property of Sladen Malartic Mines, Limited, is in the northern half of Fourniere township, Abitibi county, Quebec. The group is large, but the part so far found to be of economic interest is a strip 3,200 feet long between the Canadian Malartic property to the west and the East Malartic and National Malartic properties to the east ( Fig. 1).The original claims were staked in 1923 and 1924 by St. B. Sladen and H. S. Kennedy because gold was known to occur on claims nearby. In 1928, detailed mapping of the Malartic Gold Mines property (now Canadian Malartic) showed the presence of an east-west gold-bearing zone traceable almost to the Sladen boundary. During the winter of 1929, a hand-driven drill was used to secure short sections of core through casing pipe sunk to bed-rock. This proved the existence of the main Sladen ore zone, but it was not until the price of gold was increased, in 1934, that serious work was attempted.Underground work was started in 1935 and milling in January, 1938. To the end of 1945, 168,882 oz. of gold were recovered from 1,641,974 tons of ore, an average of 0.103 oz. a ton.GEOLOGYThe bed-rock underlying' the Sladen Malartic property consists mainly of Precambrian greywacke and volcanics that appear to form a conformable series with a general northwest strike and vertical to steep northerly dip. Except where disturbed locally by drag folds or faults, tops face north. Intrusive rocks that range in composition from diorite to granite cut the sediments and volcanics. The basic types, generally quartz diorite and diorite, form dykes or sills in the volcanic rocks. The more acidic types, mainly quartz syenite and related porphyries, intrude the volcanics and the sediments in the form of dykes, sills, and larger, stock-like bodies.The orebodies are parts of slightly shattered or brecciated zones, mainly in greywacke, but partly in syenite, diorite, and volcanics, that have been more or less replaced by fine-grained quartz, pyrite, and minor amounts of sphalerite, galena, sylvanite, petzite, and gold."

Jan 1, 1954

By A. B. Fly

Borehole mining combines the principles of hydraulic mining, slurry mucking and rotary drilling. The borehole is drilled with conventional equipment and is cased down to the top of the mining zone. The borehole mining tool is comprised of the kelly-swivel assembly, multiple drill-pipe sections, and the jet-pump barrel assembly as shown in Fig. 1. The kelly swivel is fitted with a bail to support the mining tool. The kelly drive bushing engages the rotary table to allow the rotation of the mining tool while it is being operated. The jet-pump barrel assembly is comprised of the sidewall jet nozzles, the jet-pump assembly, the suction screen, and the tricone rock bit. Clean fluid is pumped at high pressure through the kelly hose to the high-pressure swivel on the mining tool. The high-pressure pipe conducts the fluid down to the sidewall jet nozzles, the pump jet nozzle, and the tricone rock bit. The sidewall jet streams cut the formation and wash the cuttings down to the rock bit. High-pressure fluid issues from the water courses to clean the bit and to agitate the cuttings. Rotation of the mining tool causes the rock bit to grind any oversize material enough to permit its passage through the suction screen. High- pressure fluid issues from the pump jet nozzle to provide the lift needed to pump the slurry to the surface. The slurry is discharged into the settling pits where the cuttings are deposited and the clean fluid is returned to the suction of the high-pressure pump.

Jan 3, 1969

By Daniel Ng

The U.S. Bureau of Mines-Michigan Technological University mine ventilation mainframe program was successfully adapted for execution in a personal computer (PC). The hardware requirement can be as modest as 256 kilobytes (33) of random access memory (RM) and two floppy disk drives. A version compiled for a PC possessing 512 Kb RAM has arrays dimensioned to accommodate 512 separate mine airways and junctions, and it contains all the features and capabilities of the original version. It has successfully analyzed all the ventilation networks tested, including a very large commercial mine (404 airways, 237 junctions, and 5 fans). In all cases the PC version produced practically identical results as obtained from the mainframe computer. In all respects, the PC version performed the same as the mainframe version with the exception of execution speed When a numerical coprocessor is employed, execution time can be reduced by more than 50%.

Jan 1, 1989

By P. Latostenmaa, T. Hailemariam, M. Lundström, P. Halli

Doré process is unique way to treat precious metals in the copper electrorefining plant, since it uses anode slime as a raw material. In this pyrometallurgical process, also slag is produced together with Doré metal. However, the process is never ideal, and a part of metal is always lost into the slag. By using Doré slag as raw material for simply mineral acid leaching, some of the lost elements can be extracted and recovered, thus, increasing the sustainability and keeping metals in the circular economy loop. The Doré process itself is developed to convert almost all precious metals and PGMs in the Doré metal, leaving other elements into the slag fraction. The Doré slag consist of slag formers, such as borax and silica based minerals, but contain also traces of sealing materials. In addition, the Doré slag is rich in metals present in the anode slime, such as Cu, Bi and Sb, which are not converted into the Doré metal. There are only few published applications at the precious metal plants, where conservative grinding and flotation circuits have been utilized for the enrichment of valuable metals present in the Doré slag fraction (Godbehere, P.W., 1983; Segawa, C. and Kusakabe, T., 1996). However, the present study shows an alternative approach for the recovery of metals present in the Doré slag by hydometallurgical approach. The study focus on direct mineral acid (aqua regia) leaching of metals present in the Doré slag. The initial dissolved concentrations of Cu, Bi and Sb from Doré slag in the temperature range of 30-50 °C under oxygen purging with addition of 1 vol-% of H2O2 are presented. Chemical and mineralogical analyses were performed for the raw material, leaching residue, and leaching solutions in order to ascertain the leaching behavior of the metals of Bi, Cu and Sb.

Jan 1, 2018

By Mei Song, Qingyu Deng, Xuewei Lv, Lu Liu, Chenguang Bai, Meilong Hu

"The carbochlorination of several silica materials was carried out in the temperature range from 900 °C to 1200 °C. In this study, silica oxides and gaseous chlorine with carbon as reductant were used. The optimal carbon silica mole ratio in different temperature was calculated by Factsage software and the results showed that the optimal values are 1.2, 1.4, 1.6, 1.8 at 900 °C, 1000 °C, 1100 °C, 1200 °C, respectively. According to the experiments, the chlorination ratios of several silica materials were increased with temperature increasing. In the same temperature, the chlorination ratio of diatomite is the maximum and the chlorination ratio reaches 79%% when C/SiO2 reaches 3 at 1100 °C.1, IntroductionPolycrystalline silicon is the main material to manufacture the silicon polished section, solar battery[1] and high purity silicon wafers[2], also which is the most basic function material of semi-conductor industry, electronic information industry and solar photovoltaic battery industry[3]. The conventional manufacturing process of polycrystalline silicon would be divided into three parts: the improved Siemens method, which was introduced and became the main process to produce the polysilicon products in China. Silane method and fluidized bed method. Silicon tetrachloride and chlorosilans have been employed as by-products in several fields like electronic, telecounications and metallurgy[4-6]• At present, the main applications of silicon tetrachloride include production of trichlorosilane by catalytic hydrogenation, synthesis of fumed silica and ethyl orthosilicate, production of optical fiber grade silicon tetrachloride.The conventional routes for the silicon tetrachloride production have been reported, including the direct chlorination and the chlorination process of ferrosilicon, abandon catalyst and silica[7]."

Jan 1, 2013

By Brad Murray

Evaluating the performance of a shielded tunnel boring machine (TBM) can be difficult because the ground cannot be observed directly and in relation to the TBM attitude within the excavation. It is difficult to determine whether performance problems are caused by ground loading, steering issues, fine muck packing against the shield, or migration of annular grout around the shield. The Arrowhead Tunnels Project in Southern California uses strain gauges on its shielded hard rock TBMs to detect shield strains early and correlate them with tunneling conditions, thereby increasing the chances that problems will be correctly diagnosed and addressed to optimize TBM performance. The frequent automatic measurement of shield strain has also been valuable by confirming whether remedial methods used to free the machine after stoppages are effective. This paper discusses the qualitative interpretation of characteristic strain patterns on the Arrowhead Tunnels TBM shields and discusses installation details and special considerations for setting up a strain measurement system.

Jan 1, 2008

By Geoffrey Fosbrook, Donald Phillips, Anil Parikh

The Second Avenue Subway is a $16.8 billion project planned by the Metropolitan Transportation Authority (MTA) in New York City. It will reduce overcrowding and delays on the Lexington Avenue Line, improving travel for both city and suburban commuters, and improving access to mass transit for residents of the East Side of Manhattan. The project is a new, two-track, 13.5 km (8.5 mile) subway extending from Lexington Avenue at 125th Street in Harlem on the north end of Manhattan, to Water Street at Hanover Square in Lower Manhattan. The first phase of construction includes rock tunnels from 92nd Street to 62nd Street and connection to the existing 63rd Street station, three new stations, and track and systems from 105th Street to 63rd Street, allowing service between 96th Street and Brooklyn via an existing Broadway Line. The following describes the Project in detail, discusses the construction challenges addressed in the design, and the initial design/build contract to be awarded in 2005. A discussion of the planned mined construction of two rock caverns and a cut-and-cover station construction are also included.

Jan 1, 2005

By A. B. Dyes

In the operation of a water-driven reservoir, a free gas saturation can he established by maintaining production rates fast enough to cause the reservoir pressure to decline below the bubble point. The benefit of such a procedure on the displacement efficiency of the oil by water is illustrated for two types of sandstone samples from one reservoir. Those rock samples showing the poorest recovery to water drive in the absence of a free gas saturation give the most improvement in the presence of a free gas saturation. Employing one type of reservoir fluid (low .shrinkage) the benefit of evolved gas on oil displacement is calculated at several reservoir pressures below the bubble point. This demonstrates the presence of air optimum pressure for water displace,rnent which is .several hundred pounds per .square inch below the bubble point. Displacement of oil at the optimum pressures results in the removal of 7 to I? per cent more oil than would be obtained by displacement at the bubble point pressure. In some instance. this magnitude of increase may be worthy of consideration in establishing the maximum efficient rate of production from many water-driven fields. INTRODUCTION For many years the belief that the use of gas could be combined with that of water to result in a better recovery operation than the use of either of these phases alone has been prevalent in the oil industry. This is evidenced by the several field trials which have employed the injection of gas and water in combination.1.2.v In most cases the small amount of any additional recovery, in combination with the limited knowledge available on the older reservoirs, has left uncertain the influence of gas on recovery in these earlier attempts to combine the use of gas with water. Research studies in recent years have demonstrated through laboratory. floods the magnitude of the benefit of the presence of gas on the displacement of oil from sandstones by water.5,6,7,8,9,10,11 In addition, studies of the distributions of the phases which are present during the displacement process have developed concepts concerning the mechanism by which this benefit is obtained."." It now remains for the engineer to incorporate these findings into the general technology of reservoir operations. It is the purpose of this paper to illustrate that the production of a water-driven reservoir at pressures below the bubble point is one such operation whereby improved oil displacement efficiency can be obtained as a result of gas evolution. The establishment of a gas saturation by evolution of dissolved gas was one of the techniques used by several investigators in the laboratory studies. The possibility of obtaining the benefit of gas evolution in water-driven reservoirs by producing at pressures less than the bubble point has 3150 been pointed out previously." The desirability of this operation has undoubtedly

Jan 1, 1955