Search Documents

By G. S. Dobby, N. J. Contini, S. W. Wilson

Scale-up and simulation of flotation columns requires construction of mathematical models which employ, as a minimum, rate constants for quantifying particle recovery in the collection zone as well as split factors for quantifying froth zone performance. To date, measurement of these rate parameters has proven to be difficult, due to the interdependent nature of the collection and froth zones. This paper describes a technique for making these measurements. The method requires recovery data from two modes of operation: countercurrent and cocurrent. In cocurrent flow slurry is fed at the bottom of the column and tailings are withdrawn a short distance below the froth interface. Countercurrent mode is conventional operation. The critical difference is that particles which are dropped out of the froth in cocurrent mode are immediately lost to tailings, while in countercurrent mode the particles are subjected to recollection. Fitting of the measured recoveries to the equations that describe flotation in the two modes yields rate constant or recovery values for both the collection and the froth zones.

Jan 1, 1988

By J. Qiu

By means of natural sedimentation, two different bentonite samples from Shandong province were purified, this paper studies the Hydro-properties of the two purified montmorillonite samples. Firstly, the layer charge of two purified montmorillonite samples were calculated by crystal structure formula reckon method and general hydro-properties were also measured. The research results showed that the layer charge of montmorillonite correlated well with its hydro-properties: mont-morillonite with lower layer charge had better hydro-properties, such as Mont-1, which had higher swelling volume and gelling value with lower CEC; while, montmorillonite with higher layer charge had worse hydro-properties, such as Mont-2, which had lower swell volume and gelling value with higher CEC; it proves that the hydro-properties of montmorillonite depends on its layer charge characteristics, layer charge characteristic is the inherent factors deciding the hydro-properties of montmorillonite, montmorillonite with lower layer charge has better hydro-properties than the one with higher layer charge. In this paper, the relation between the medium condition and colloid performance of Mont-1 are also studied. The results show that the hydro-properties of Mont-1 could be changed by changing slurry concentration (w/w) and shear rate or adding certain amounts of inorganic cation electrolytes, dispersants and surfactants. The viscosity of montmorillonite slurry could be enhanced by increasing slurry concentration,adding univalentcation electrolytes (less than 4% w/w) or proper amounts of dispersants and surfactants (less than critical micelle concentration); The slurry viscosity could be reduced by decreasing slurry concentration, increasing shear rate, adding proper bivalent (more than 4% w/w) cation electrolytes or proper quantities of dispersants and surfactants (more than critical micelle concentration).

Jan 1, 2014

By Frederic A. Verheyde

The CPT pile design method of the ‘Laboratoire des Ponts et Chaussées’ (LPC) uses the cone resistance (qc) for the design of axially loaded piles. It was originally proposed in 1982 and was revised in 1993 and 2012. It has been widely used in France for several decades and is included in the current French pile design code. The objective of this paper is to summarise the two first versions (1982 and 1993) of the method and to detail the most recent one as described in the current French pile design code (AFNOR 2012).

Nov 1, 2022

By Pramod C. Thakur

Coal is a major source of energy in the world today and will, undoubtedly, continue to be so for the next few centuries. Naturally, a great number of studies has been made of its physical and chemical properties. Unfortunately, the work on technical properties which influence the mining of coal and the consequent yield of inflammable gases and respirable dust particles has not progressed at a comparable pace. Coal is a brittle material. Irrespective of the mechanism of breaking coal, some dust is always produced. In mining parlance dust is defined as solid particle, smaller than 100 microns (micron = 10-6 meter), in size Coal dust, when raised into a cloud, creates two well known hazards in mines, namely, the coal dust explosion and Coal Workers' Pneumoconiosis (CMP). The latter is, perhaps, the greatest environmental hazard in U.S. coal mines today. In this context it is not only natural but also necessary to investigate the proneness of a coal seam to respirable dust production. It has been established that the amount of dust produced is a function of two groups of variables (1), (2), viz. (1) Material dependent variables, e.g., moisture content, compressive strength, hardness, etc. (ii) Breaking mechanism dependent variables, e.g., type of machine, depth of cut, etc.

Jan 1, 1973

In his account of the Thackaringa sulphide ore, Lawrence (p. 92) reports the presence of valleriite as a minor accessory in chalcopyrite. He says that it is readily identified by its intensive anisotrophy and reflection pleochroism. He also gives (p. 87) the chemical formula as Cu8Fe4S7 Recent work by Evans et al. (1964), Chamberlain and Delabio (1965), and Schidlowski and Otteman (1966) suggests that most material identified as valleriite is, in fact, mackinawite. Mackinawite and valleriite are both extremely anisotropic and strongly reflection pleochroic, and so with fine-grained material it would be hard to distinguish them optically.Mackinawite, according to Evans et al. (p. D66) is a copper-free iron sulphide (PeS) with small quantities of nickel, whereas valleriite is considered to be a dimorph of chalcopyrite (CuPeS2 ). They found that mackinawite is much more widespread than valleriite, and, unlike the latter mineral, is commonly included in other sulphides, particularly chalcopyrite.Lawrence (p. 92) states that the valleriite inclusions are up to 0·01 mm long, so that an electron probe microanalysis should be quite feasible and provide a ready answer to this query.L. J. Lawrence: I thank Dr Townend for his comments on the occurrence of a valleriite-like mineral embedded in chalcopyrite from Thackaringa. The problem of distinguishing valleriite from mackina...

Jan 1, 1967

By J. Gao, H. O. Gekonde, S. V. Subramanian

"The functional role of inclusions at low cutting speeds is to promote ductile fracture in chip formation process, whereas the role of inclusions at high cutting speeds is to prevent tool crater wear by suppressing the tribological phenomenon of seizure at the tool-chip interface. Glassy oxide inclusions are engineered into the workpiece to form a viscous layer in-situ at the tool-chip interface at high cutting speeds. The viscous layer lubricates the tool-chip interface to prevent the seizure. In comparison with the large volume fraction of inclusions needed for promoting ductile fracture at low cutting speeds, the amount of inclusions required for lubricating the toolchip interface at high cutting speeds is very small and is in the range that is typical of clean steels. The chip fracture process at high cutting speeds is aided by strain rate hardening of the matrix, which facilitates chip disposal of relatively clean steel.Inclusion engineering for high speed machining involves the control of the rheology and composition of inclusions to meet target viscosity at the tool-chip interface. The application of thermodynamic models in controlled production of inclusions in steels designed for high speed machining is discussed."

Jan 1, 1998

By F. R. Morral

HOT-DIPPED heat-treated zinc coatings on sheet steel were examined with X-rays. The phases identified were compared with those listed in the modern literature of the zinc-iron system. The zeta (FeZn13) phase is shown to correspond to the phase found by Schueler (1925) in heat-treated zinc coatings. An investigation was undertaken to determine the phases present in hot-dipped FIG. I.-SYSTEM IRON-ZINC ACCORDING TO J. SCHRAMM.11 heat-treated zinc coatings on steel sheets and wire. This kind of coating on wire was studied some years ago by Schueler1 by microscopic and chemical methods. He reported a new phase, FeZn10. Later, Clark and Stillwell,2 using X-ray crystal analysis, identified a new phase in ordinary galva-nized wire, which was assumed to be the FeZn10 phase.

Jan 1, 1940

Jan 1, 1961

By Guozhu Ye

"One of the most essential problems associated with the treatment of EAF dust is its high content of halogens. For most thermal processes for zinc recovery, such as the plasma processes with a zinc condenser, the halides in the gas stream will form a dross phase that results in a low zinc yield. For those with zinc oxide as main product, such as Waelz oxides, the high halogen content in the product implies a great degradation of the product quality and the product can only be sold at a low price. Further processing of zinc oxide with high halogen content either by pyrometallurgical or hydrometallurgical processes will also result in process problems.This paper will review the pre- and post-treatment alternatives for halogen removal based on the comprehensive characterization work that has been carried out at MEFOS and the preliminary experimental results.The experimental results show that chlorine and fluorine content could be reduced to 450 ppm and 50 ppm respectively by selective sulfation, and to about 200 ppm by soda leaching. Selective sulfation of zinc oxide in the EAF dust will also be discussed."

Jan 1, 2000

By R. W. Smith, D. L. Taylor, K. A. Altman

The importance of metallurgical information in reaching appropriate decisions during the development of mining projects is demonstrated. A financial analysis is calculated using a simulation that includes random number generators. The results are compared to the results of a traditional sensitivity analysis. The traditional analysis is shown to have the potential to overestimate the value of mining projects. The type of statistical distribution selected for the random number generator affects the results significantly. The statistical method of analysis provides insight into the amount of metallurgical testing to be completed and verification of how representative the samples are.

Jan 1, 2000

By M. I. Brittan

A technique has been developed that analyzes routine mill operating data to determine the key operating parameters responsible for gold losses to tails. These parameters represent the prime operating variables having a dominant effect on gold recovery. The technique quantifies these effects for the specific plant being analyzed, providing a tool to optimize recovery and costs and so enhance the mine?s cash flow. The quantitative relationships generated will be different for each ore and plant: every case is site-specific and has to be treated on its merits. Examples are provided to illustrate the considerable metallurgical and financial benefits which can be realized from optimization. The examples are taken from case studies of mills in four major gold mining districts of the world.

Jan 1, 2010

By A Melkumyan, F Ramos

This paper addresses the problem of prediction of grade variables over volumes (block estimation) for an autonomous mine. Resource estimation is usually concerned with the prediction of the quality of material over volumes (blocks in resource models). This problem is tackled by developing Bayesian block estimation with the Gaussian processes (GPs) framework. GPs are commonly used for nonparametric regression and classification and offer an elegant solution to deal with incomplete knowledge and information. A GP is defined by its mean and covariance function. The parameters of the covariance function can be learnt by maximising the marginal likelihood of the data. This offers a way of automating the covariance fitting process, while at the same time allowing for an assessment of how well the covariance function fits the data. Within the GP framework the calculation of the average grade over a volume can be performed using Bayesian quadrature, which treats an integral as a random variable. First, it is demonstrated that the block kriging equations in geostatistics are the same as Bayesian quadrature. Then, it is determined when closed form analytical solutions for the integrals are possible and quadrature approaches for approximations are briefly discussed.

Sep 26, 2011

By Rafael Padilla

The recovery of copper from chalcopyrite concentrates by leaching is difficult due to the slow dissolution kinetics of this mineral in most leaching media. However, recovery of copper from sulfidized chalcopyrite (a mixture of CuS and FeS2) by leaching is faster and could be selective depending on the leaching media. In this paper, the result of an investigation on the H2SO4-O2 pressure leaching of sulfidized chalcopyrite is presented. The variables considered in the study were stirring speed, concentration of sulfuric acid, temperature, and partial pressure of oxygen. The experimental data indicated that stirring speed over 500 rpm and sulfuric acid concentration over 0.1 M had very little effect on the leaching rate. An increase in temperature from 90 to 100 ºC increased both copper and iron dissolution; however, further increase to 120 ºC affected negatively the copper dissolution. Oxygen partial pressure was found to be the main variable that controls the copper/iron selectivity of the leaching. An increase in oxygen partial pressure increased significantly the rate of copper dissolution but deteriorated the copper/iron selectivity. The analysis for sulfur of the leaching solid residues indicated that most of the copper sulfide sulfur in the sulfidized concentrate oxidized to elemental sulfur.

Jan 1, 2006

By G. J. Borbely, E. A. Devuyst, V. A. Ettel

"A new method for oxidative destruction of cyanide in industrial waste waters and slurries, such as gold mill barren liquors, tailing slurries and flotation tailings has been developed at the Inca research laboratories. Rapid decomposition of cyanide and related species is attained by treating the waste waters with a mixture of S02 and air at controlled pH and in the presence of a small amount of copper which acts as a catalyst. The approach selectively oxidizes cyanide and metal cyanide complexes, and also removes iron cyano complexes which are not removed by alkaline chlorination.The new method is shown to be less reagent intensive and therefore more economical than alkaline chlorination for treating gold mill and flotation waste waters. INTRODUCTIONOver 90% of the gold mined in Canada is extracted from the ore by ""cyanidation"". Wastes from the process consist of tailings which contain free cyanide, cyanide combined with heavy metals, thiosalts and thiocyanates. Because of the concern over the effect of toxic cyanides on the environment, all cyanide containing effluents will have to be treated in the future to meet certain government set concentration limits."

Jan 1, 1982

By I. M. Bernstein

The steady-state creep behaviov of zirconium and zivcaloy-2 was examined in the temperature vatlge 520° to 620°C A1 low stresses the creep rates were cimracterized by a linear stress dependence; at highev stresses the stress dependence was much more pronounced. Temnperature-cycling tests yielded values for the aclivation enevgy for creep. Various tlzeories were examined in the ligltt of- the experimental re-sults and it mas concluded that the low-stress creep behavior is the result of the stress-direcled diffusion of vacancies along gain boundaries. It has been observed,"&apos; usually under conditions of high temperature and low stress, that creep deformation can occur for which the steady-state creep rate is linearly dependent on the applied stress. For magnesium and certain magnesium alloys, Harris and ones&apos; and ones&apos; have argued that this type of creep occurs by mass transfer as a result of the stress-induced generation and migration of vacancies, along a gradient defined by the stress direction. Jones&apos; demonstrated that the rate-controlling diffusion path is sensitive to grain size and temperature, and that by suitable control of these variables creep could occur by vacancy diffusion either predominately along grain boundaries or through the lattice. Recently, Jones3 suggested from an examination of limited high-stress data for zircaloy-2, composition in Table I, that significant diffusion creep could occur at low stresses, at least between 375" and 500°C, controlled by grain boundary vacancy diffusion. This process could have an important implication in assessing the role of zirconium alloys as a structural or cladding material in certain classes of nuclear reactors, since it predicts creep deformation far in excess of any estimates based on extrapolating slip creep data from higher stress levels. If the diffusion creep process occurs it should be possible to describe the total steady-state creep rate of zirconium and its alloys as the sum of two terms, Eq. [I]; the first term relates to a slip creep process important at high stresses and which is manifested by a much more pronounced dependence of creep rate on stress4 than diffusion creep and the second to a process controlled by mass transfer,5&apos;6 dominant at low stresses: where A and BI are parameters which can depend on structure, Ql and Q2 are the activation energies for the particular creep process occurring, and n describes the sensitivity of the creep rate on stress. It is the purpose of this paper to present some direct experimental evidence in support of this view. It is recognized that other analytical approaches have been proposed to explain data of this kind and these will also be discussed. 1) EXPERIMENTAL PROCEDURE Flat creep specimens (gage length 1 by 0.25 by 0.02 in. approx) were prepared from cold-rolled, argon-remelted, crystal bar zirconium and cold-rolled commercial-grade zircaloy-2, the analyses of which are given in Table I. The specimens were annealed at a pressure of < 10-5 Torr at temperatures from 625" to 675°C for 2 hr and slow-cooled. This treatment produced stable grains of average size (defined here by the average linear intercept) of for zirconium and -4xin. (-10 p) for zircaloy-2. The specimens were tested in a dead load tensile creep rig. The stress was maintained constant by adjusting the applied load after approximately each 1 pct of strain. The specimen temperature was controlled to better than +1°C. This system had a small thermal lag, so that rapid temperature changes were possible. To minimize corrosion, the specimens were tested in high-purity (99.95 pct) argon, further dried,

Jan 1, 1968

It is argued that the capture of par- ticles by bubbles is primarily caused by hydrophobic ("structural") attraction forces. Neither dispersion forces nor double-layer forces can account for hydro- phobicity, though the latter are known to influence the kinetics of capture. The recent experiments of Israelachvili and Pashley (Nature, 300: 341-342, 1982) with hydrophobic mica plates provide the first measurements of the range and magni- tude of hydrophobic interaction forces.

Jan 1, 1984

By Henning E. Soderberg

Yesterday, air pollution was somebody else&apos;s problem -- today, it is everybody&apos;s problem. The coal industry with thermal coal drying, is aware of their problem and the necessity of doing an acceptable job; however, there is much to be said as to how good a job is required and what performance limits should be set up. American Air Filter Company has been one of the pioneers in the solution of the thermal coal dryer dust problems, Because of high moisture content, products of combustion and occasional temperature surges, only wet collection has been considered as the practical approach. Our first installation goes back some 12 years with a total to date of 29 Individual wet collectors, each, fabricated of suitable corrosion-resistant material, at 14 operating plants. To eliminate a potential air pollution problem, a performance requirement of not more than approximately one-quarter (1/4) grains per cubic foot in the dust collector discharge was used. In nearly all installations, operating performance surpassed requirements, but discharge stacks were not entirely free of discoloration. However, plant nuisance and air pollution complaints were eliminated. This satisfactory performance was accomplished by medium priced wet dust collectors operating at a 4-6" W.G. pressure drop with cater drain requirements of about 1 gallon of drain water per 1000 cubic feet of air exhausted.

Jan 1, 1962

By Turner W. G, Trundle R. S, Medland D. G

Contracting has evolved from basically a tradesman providing a service for an `employer&apos; to a multi disciplined organisation providing an all compassing service for a client.Having commenced its activities as Thiess Bros Pty Ltd, providing simple earthmoving services in rural Queensland, Thiess Contractors Pty Ltd which provides a wide range of services for Governments and Industry is used as an example of an experienced multi-disciplined Contractor.

Jan 1, 1992

By Abdelhak Bentriou

The choice of tool for the first well of an oilfield or gasfield is an important factor, given that we will be drilling with the same type of tool for the entire phase and explains why we need to have another type for comparison based on the efficiency of the tool and its ability to crush the rock, and the wear of different types of tools. Development of theoretical and practical tests to determine the optimal regime for drilling is required to take into account the characteristics of rock layers crossed. Classification of boring tools is based on the geometry of the teeth and depends on the hardness, the abrasiveness of rocks as well as their hydraulic system, but it is better to classify them according to the working conditions with a coefficient designating a discriminant. This is called physical characteristic of the drilling tool. The goal is to designate each element of the tool by a coefficient. Results were obtained from laboratory tests. Modeling the initial rate of progress by different types of tools allowed us to determine an adequate mathematical model of the speed initial progress in clean conditions. Using experimental data and statistics we have established the mathematical model of the average speed of progress as a function of time. With these equations we can determine the wear evaluation and analysis of these factors as an approach to classification according to their characteristics. The main equations for the selection of drilling tools will be based on the optimization of drilling parameters for each type of tool. After analysis, we choose the tool that gives a better forward speed with an optimal load and axial rotation.

Aug 1, 2013

By Marcie A. Greenberg, John C. Patton, R. Tim Thompson

The Fence Lake Project is located in the Salt Lake coal field, an extension of the San Juan Basin. Geologic formations exposed in the Project area range in age from late Cretaceous to Quaternary. Coal is encountered in the Moreno Hill Formation (upper Cretaceous). Salt River Project (SRP) followed the basic textbook approach for the exploration, regional appraisal, detailed reconnaissance, detailed surface detailed and three dimensional sampling (physical exploration). SRP is exploring this property as a potential fuel source for the Coronado Generating Station. Therefore, for the physical exploration stage, the quality sampling program was designed from a utility company viewpoint to determine possible impacts to the Station. Exploration drilling was completed in spring, 1982; September, 1982, and summer, 1984. Engineering, environmental, and land acquisition studies - in the Summer, 1984 Program to more closely evaluate the potential Fence Lake Project coal supply option for the Coronado Generating Station. Studies, including drilling, are ongoing at this time.

Jan 1, 1985