Search Documents

By E. R. Buchanan, R. E. Reed-Hill

A transmission electron microscope study was made of magnesium single crystals deformed in torsion using the basal pole as the forsional axis. While this type of deformation is predicted to result in the formation of hexagonal networks of screw dislocations, these networks were not observed. The basic dislocation arrangement consisted of arrays of nearly parallel and approximately equally spaced dislocations. The average dislocation density was over an order of magnitude higher than that required to account for the torsional deformation. The observed high rate of work hardening in these crystals is consistent with both their high dislocation densities and the arrangement of dislocations in pile-ups. The experimental observations are also in agreement with the assumption that dislocation sources are activated not only at the surface but at interior locations as well. In considering torsional deformation, Amelinckx and Dekeyser1 postulated that when a torque is applied to a crystal oriented with a glide plane normal to the specimen axis, deformation occurs by the following steps: 1) Nucleation of dislocation sources at or near the specimen surface in areas where the shear stress, resolved along a slip Burgers vector, is a maximum; 2) the screw orientations of the dislocations accommodating the twist move inwards towards the specimen center. If two glide directions lie on the glide plane, the geometry shown in Fig. 1 should result; 3) the screw dislocations that pile up in the central part of the specimen cross-slip to form a grid. At the same time, screws of opposite sign and most edges leave the specimen. Tinder,2 using zinc crystals twisted about the basal pole, independently reached essentially the same conclusions. He suggested a mechanism involving nucleation of ?(1120) screw dislocations at the six points of highest resolved shear stress that lie on the cross-section near the surface. Under the applied shear stress these dislocations were assumed to move inward and interact so as to form a hexagonal network of screw dislocations. Today it is often accepted that rotational slip occurs by a mechanism of the above type, but to our understanding this has never been experimentally proved. This paper reports an experimental study of rotational slip, using magnesium single crystals, that indicates that in this metal rotational slip does not conform well to this mechanism. EXPERIMENTAL PROCEDURES Mechanical Testing. Specimens with a (0002) axis were prepared from magnesium crystals of 99.95 pct purity grown by Jillson's3 modified Bridgman technique. The crystals were acid machined into cylindri-

Jan 1, 1970

By H. Y. Yancey, B. M. Bird

One of the problems studied by the U. S. Bureau of Mines in cooperation with the University of Washington has been the re-treatment of table middlings. Hydraulic classification has given the best results. Instead of using the classifier to prepare the feed to the tables, as has been the practice for many years in ore dressing, it is used to separate part of a middling product that cannot be re-treated successfully on the table. Middlings are desirable in a table plant because the separation according to specific gravity is incomplete; that is, in the products of the table there is always an overlapping of free particles of coal and refuse that can be distinguished with heavy liquids such as are used in the float-and-sink test. The causes of this overlapping may be divided into two groups, those outside the table separation itself and those inherent in the table separation. The first of these groups includes, among other causes, the following: (1) poor adjustments of the table, (2) overloading or underloading the table, (3) irregularities in the quantity and quality of the feed, (4) irregularities in the power and water supply, and (5) a vertical dancing motion of the table deck due to weak foundations. These causes of overlapping are largely unnecessary in a properly designed and constructed plant; but whenever they are present they materially affect the character of the middling product, and hence the problem of re-treatment. The other group includes three additional causes: (6) small differences in specific gravity between coal and impurities, (7) a size-specific-gravity relationship of the coal and refuse particles in the table feed such that the sizing action of the table opposes the separation according to the specific gravity, and (8) shapes of particles that prevent a separation. The sixth, small differences in specific gravity, may be a very important reason for an incomplete separation. The change in specific gravity from coal to shale is always gradual and the designation of one part as coal and another part as refuse is arbitrary. If some specific gravity, such as 1.45, is chosen as the dividing point between washed coal and refuse,

Jan 1, 1930

By [Miroslaw] M. Hajdasinski

The Payback Period (PBP) is one of the most widely applied project evaluation criteria 'in the mineral industry. As much as this criterion is liked by practitioners, it is also criticized by academicians who seriously question its validity. Inspired by this criticism, the author of this paper examines the classical definition of the PBP criterion, and formulates a new one designed for both investment and borrowing projects. It is demonstrated that the PBP, in its revised version, is free from all the shortcommings of the old one, and is fully compatible with the Net Present Value (NPV) criterion, as well as with all the other NPV compatible project evaluation criteria. Since the traditional approach to the comparison of mutually exclusive projects (MEP1s) by means of the PBP criterion has been incorrect, the paper also outlines the correct approach to this problem. Finally, owing to the fact that the PBP depends on the assumed interest rate, and using a specially developed computer program, the PBP is graphically presented, in six numerical examples, as a function of the interest rate.

Jan 1, 1989

By E. A. Holbrook

IN my thirty years of educational work in the mineral industries and other engineering fields, this past year has been the most unusual and difficult one. Contact with educators from other schools leads to the conclusion that the same situation is countrywide. The first of our difficulties came from the shortsighted policy of the Selective Service in taking out of the colleges, continuously, all engineering students as soon as they had reached their eighteenth birthday. England, Canada, and Russia, too, even in the midst of their critical war situations, had the good sense to keep their young engineering brains in college, for they realized the vital necessity of a steady flow of engineering graduates into the war industries and into the postwar peace industries. As a result of the policy of our Government, our engineering schools were left with only a handful of students who had been rejected for military service. Our colleges, faced with the prospect of several years without students and without income, hastened to give leave of absence to many of their competent teachers who quickly were taken into industry and in many instances are now being retained there at higher salaries than colleges are accustomed or able to pay their teaching personnel. We are finding it most difficult to induce these men to return to their former engineering teaching work. In my judgment, it will take us three or four years to restore our engineering departments to their former level in quality of instruction.

Jan 1, 1946

By Thomas V. Falkie, R. Venkataramani

The purpose of this work was to Investigate the rate at which coal is delivered from the underground working face by gathering arm type loaders as employed on continuous mining machines, to identify the factors - geometrical , geological, mechanical, or procedural - which affect the delivery rate, and to develop quantitative rate-descriptive equations for the loading function. The mathematical techniques employed were factor analysis and multiple linear regression. It was determined that the coal-cutting function of the continuous mining machine is the factor that primarily Influences the loading function The geometrical factors -the dimensions of the work area In relation to the dimensions of the mining machine -were the factors of secondary influence. Fifty-five percent of the experimental variation in the loading function was explained in terms of the six most prominent Independent variables. It is expected that this work will be useful In operations-research studies as applied to underground coal mining, and with refinement will enable mine planners to select equipment based on the operating characteristics of the equipment and the mining conditions.

Sep 1, 1972

THE CHAIRMAN (J. W. MALCOLMSON, Kansas City, Mo.).-Gentlemen, Dr. P. J. O'Gara, Director of the Department of Agricultural and Smelter By-Products Investigations, of the American Smelting & Refining Co., Salt Lake City, Utah, is here; he has given attention to this very important problem and I will call on him for a few remarks. P. J. O'GARA, Salt Lake City, Utah.-I have had charge of the investigations of the smoke problem for the American Smelting and Refining Co. during the past four years. One of the worst burns we ever experienced occurred shortly after we began putting all our gases through the baghouse. This occurred in 1914 after the roaster gases had been put through the baghouse; previous to that time, the greater portion of the roaster gases was not put through the baghouse. Everyone knows why a hot-air balloon goes up. The hotter the air in the balloon, the higher it will go. In other words, hot gases will rise higher than cold gases. When gases are handled in any way that will tend to lower their temperatures, these gases are going to travel less high in the atmosphere and will therefore tend to reach the ground sooner than if they are turned out very hot. So far as injury to vegetable life is concerned, sulphur dioxide is the only element in smelter smoke that need be considered. The solution of the problem will be either to take out the excess of sulphur dioxide or to diffuse it high enough, up in the atmosphere so that the concentra-

Jan 1, 1918

By G. W. Leney

Iron ores occur in such a wide variety of forms that nearly every kind of prospecting, geological knowledge, and geophysical technique has some application in the search for them. The type of orebody that is considered desirable depends on political and economic considerations, on transportation and markets, on the characteristics of the orebody, on the metallurgy of the ore, and on its comparison with other available ores. In North America, materials that can be efficiently processed into high grade concentrates and pellets are now the object of most exploration work. These are usually shallow, relatively unoxidized, metamorphosed iron formations that are particularly suitable for geophysical methods of exploration. Magnetic surveys are used for the direct discovery of new orebodies, for mapping stratigraphy and structure, and at times to locate oxidized zones in magnetic iron formation. Gravity mapping provides supplementary information, indicates gross tonnages, is useful in regional studies, and can discover non-magnetic orebodies. Electrical methods have not been fully exploited but self-potential, resistivity, applied potential, electromagnetic and perhaps induced polarization surveys all have restricted but highly useful applications. The use of all geophysical techniques promises to increase as the number of exposed easily discoverable orebodies decreases. A high consumption of steel, and consequently of iron ore is the chief characteristic of an industrial society and this consumption has been increasing at an average rate of about 35% every ten years for the past century. To supply this demand, iron ores and iron bearing materials in a wide variety of forms have been exploited on every inhabited continent and in nearly every country. Nearly every kind of prospecting, geological knowledge and geophysical technique has some application in the search for them. The type of orebody that is con-

Jan 1, 1964

By B R, R Brooks, R Simcock, R Stewart

As environmental costs incurred by the mining industry become increasingly subject to critical analysis, new technology is necessary to ensure the further development of good relationships between the industry and community. Phytoremediation and phytomining are technologies that have the potential to capture the imagination and approval of the public. Phytoremediation , the in situ use of plants to extract heavy metals from a contaminated substrate, could offer an environmentally and cost-friendly alternative to traditional remediation techniques. Phytomining is the in situ removal of metals from a contaminated site or subeconomic orebody with the additional aim of recovering from the plant an economic amount of metal. Plants used in such operations, hyperaccumulators, accumulate large quantities of one or more target metals in their above-ground herbage. Upon harvesting and incineration, this plant material yields a low-volume, sulphide-free æbio-oreÆ, which can either be safely disposed of, or if the metal is of sufficient value, smelted. Investigations into the economics of phytomining nickel from ultramafic (serpentine) soils, showed that Alyssum bertolonii and Berkheya coddii could remove over 100 kg of nickel per hectare per annum from land with nickel concentrations well below the cut-off grade for conventional mining. It also appears possible to æinduceÆ the hyperaccumulation of gold into plants growing on gold tailings, or on stockpiled, low-grade gold ore. The plants used for phytoremediation and phytomining are useful colonisers as they are necessarily hardy and withstand extremes of salinity, metal toxicity and water stress that hinder the success of current revegetation procedures. As part of a rehabilitation operation, these plants may alter the geochemistry of a substrate making it more amenable to the growth of native species that should be used to restore a mining site to pre-operating conditions.

Jan 1, 1999

By Hugh Steele, Brower Dellinger

U. S. mining trends for 1956 continued steadily U+ S. uphill, technique and equipment advanced with the pull, and exploration and development of once mined districts attracted more attention than new areas. Expansion of the Ambrosia Lake district in New Mexico more than doubled known uranium ore reserves, and production began from several of the large new ore discoveries. In Canada the up trend was more spectacular, especially in exploration and development. To combat increasing problems arising from high labor costs, taxes, low grade orebodies, and dwindling discoveries, manufacturers and mining companies have continued to introduce new techniques and new products-reamer bits for enlarging small holes drilled by jacklegs, whup d'whups for drift mucking, Cryderman machines and over-the-head small crawler-type machines for shaft mucking, the 20-ton TL 220 four-wheeled tractor trailer unit for underground haulage, inertia-type dust collectors, roof bolting in conjunction with chain link fencing for wall support, wooden roof bolting using compression support of ground for wall support, and new one-use carbide bits.

Jan 2, 1957

The relative contents of Au in a series of groundwaters from water bores and exploration drillholes, located near Au mineralisation at Stawell, Ararat, Clunes and Ballarat in central Victoria, were found to be clear indicators of relative proximity to mineralisation in each region. In the same series, waters with anomalous concentrations of As distinguished Au mineralisation in bedrock from secondary palaeochannel or deep lead Au. In some groundwaters, acid pH values, high sulphate relative to other anions and detectable concentrations of reduced Fe reflected sulphide minerals associated with bedrock Au deposits. Close to some ore zones, locally anomalous groundwater concentrations of Mn reflected the Fe carbonates that accompany Au in these zones. In addition, elevated concentrations of other elements provided geochemical signatures for the aquifer lithologies associated with Au mineralisation. Of the lithological indicators Co and Ni, U and F, Rb and Cs, Mo and Li respectively reflected the mafic, felsic, potassic rich and quartz zones, principally in the Stawell mine area and to a lesser extent those at Clunes and Ballarat. Mineral stability diagrams, based on groundwater activities of K', Mgt and H`, demonstrated that a series of ore-zone groundwaters follow a trend that conforms with a biotite to sericite to kaolinite alteration sequence in aquifer mineralogy. This is a good illustration of how present day groundwaters under surface conditions can reflect the underlying mineral sequences that accompany these Au deposits. These observations around mine areas suggested that groundwater chemistry could provide a rapid and cost effective method of assessing prospectivity for An of extensive areas in central Victoria. To test this, regional sampling and analysis of 355 bore waters was carried out in a region where potential An bearing rocks are covered by Mesozoic and Cainozoic sediments and volcanics. Contoured elemental abundances and distribution from this program indicated five zones in which groundwaters had elevated Au and despite the cover, appeared to reflect variations in the underlying Palaeozoic rocks. Three of the Au zones could be in terrain affected by extensions or intersections of faults, a feature in common with the established Au deposits in central Victoria. Reflections of concealed Palaeozoic rocks included a possible zone of concealed Cambrian greenstones that coincides with three of the Au zones. It was concluded that each of the An zones represents a groundwater Au focus that warrants follow-up exploration.

Jan 1, 1997

By R. H. Seraphim

"The Phoenix Camp, in the Boundary Creek district of southern British Columbia, produced before 1920 about 15 million tons of ore averaging more than l ·5 per cent copper, about 0.03 ounces per ton in gold, and 0·5 ounces per ton in silver. Attwood Copper Mines Ltd. conducted an exploration program in the Phoenix area from 1951to1953.Publications on the camp are listed in the bibliography. Brock's work was not sufficiently detailed to unravel the structural and stratigraphic pro bl.ems. The work of LeRoy and McNaughton is referred to later.The stratigraphic column is as follows:Tertiary.Midway Formation: Volcanics and hypabyssals; dacitic to basaltic flows, with associated dykes and sills of syenite (pulaskite in part) and augite porphyry.Jura-Cretaceous.Intrusives of quartz diorite and diorite (nearest outcrop two miles from Phoenix).Late Palaeozoic or Triassic (Attwood Series).Brooklyn Formation: Sharps tone conglomerate, limestone, grey-wacke and/ or andesitic tuff, with minor shale and basalt. Rawhide Formation: shale with minor conglomerate.Early Palaeozoic.Knob Hill Formation: Chert and andesite, with minor limestone, shale, and serpentine.This column differs from that of LeRoy in two important respects: (I) Attwood's work indicates that the Rawhide shale is basal to, rather than stratigraphically above, the Brooklyn formation. The shale contains conglomerate lenses, which become more abundant and thicker toward the top, and grades upward into Brooklyn conglomerate. Ripple marks indicate that the shale is right side up."

Jan 1, 1949

By G. Barbery

In Mineral Processing, the objective of most processes is the separation of mixtures of minerals, which are originally associated in composite particles. Feed preparation processes grinding for instance, which take place before beneficiation or separation processes do not usually break particles at the boundary between mineral phases. They produce composite ("middlings") as well as liberated particle. It is therefore necessary, in a particulate system, to determine the proportion of particles which are liberated as well as, ideally, the size distribution of minerals which remain associated in composite particles. Up to now, there has been a lack of experimental techniques to characterize completely composite particulate systems. Heavy liquid separation which is commonly used to obtain information of this type can only be applied to simple binary cases for which one mineral has a low density (lower than e.g 2.8 ). The technique which is proposed in this paper involves the measurement of parameters on polished sections of particles mounted in a matrix, and the use of mathematical transformations to reconstruct in three-dimensions the information obtained from these measurements .

Jan 1, 1977

By Lawrence M. Gochioco

One of the best kept technology secrets in U.S coalmining history involved a robust coal geophysics program used by a local coal company to detect and map various geologic anomalies and man-made structures ahead of mining for nearly 15 years. Several original mine plans were changed as a result of findings from two-dimensional (2D) and three-dimensional (3D) seismic data. They indicated the presence of geologic anomalies in reserve areas that could adversely impact future mine development and longwall production. By combining the surface seismic and exploratory drilling methods, the coal company learned how to properly leverage its risk by gathering a lot of useful subsurface information before making major commitments.

Jan 1, 2005

The curbing of expansion in tertiary level education in Australia and the question- ing of its objectives which are now occurring are likely to have important effects on mining and metallurgical education. Student enrol- ments are low but the serious shortage of specialised minerals industry graduates pre- dicted during the boom of the late 60's has not eventuated. Other manning problems of a less quantitative but possibly equally import- ant kind have been identified. They point to a need for a full and deep review of the education and training programmes available to Australian graduates planning to enter product- ion areas of the minerals industry. An alter- native educational structure providing greater flexibility is suggested.

Jan 1, 1977

By K. S. Barros, D. C. R. Espinosa, J. A. S. Tenório

Over the past several decades, electrodialysis membranes have been employed for the removal of metals from galvanizing industry effluents. However, for its technical viability, it is useful to know some properties of the system to avoid, for example, precipitation of inorganic salts, destruction of the membrane and an increase in the energy consumption. The scope of the present study is to use chronopotentiometry to determine limiting current densities, transition times and resistances of the cationic membrane HDX 100 using a synthesized solution of the galvanizing industry effluent prepared with copper sulfate and sulfuric acid in different concentrations: 0.1, 0.5 and 1.0 g/L of Cu +2. The current-voltage and chronopotentiometric curves obtained have clearly defined regions and it was verified that the Cu+2 concentration causes a significant increase in the limiting current densities and in transition times. However, a high decrease in resistance occurred because at the highest concentrations, it is more difficult to reach the zero concentration value at the membrane surface. Besides, the pH increase causes a significant decrease in the limiting current density and in the transport number, but a slight increase in the resistance due to the presence of hydrogen. The results obtained confirm that the chronopotentiometry method is a valuable tool to determine membrane properties.

Mar 1, 2017

By Morrison R

Optimisation has two distinct applications in the concentrator ò the first is in the area of the flowsheet and the operating parameters of the various unit operations ò the second is associated with the higher levels of process control. The Plant Metallurgist is faced with a library of complex theories relating to optimisation. The practical reality of optimisation lies in a combination of steady state simulation to ensure that the process route will permit maximum productivity and an appropriate process control system which will permit achievement of the production and quality objectives.

Jan 1, 1991

By Russell G. Slayback

Feasibility investigations for prospective gold mines too often neglect to consider ground water. Simple observations and tests during drilling exploration can provide useful data on probable water conditions. As the prospect becomes more serious, more detailed investigation of ground water and dewatering needs may be warranted. Ignoring ground-water conditions can lead to costly mistakes.

Jan 1, 1987

THERE are few industrial and metallurgieal processes which do not require the application of heat energy, and the modern demand for increased working efficiency has resulted in attention being paid to temperature control as a means of ensuring fuel economy and more efficient plant operation. In general, mill accuracy required is not very contant in laboratory work, and few industrial operations are controlled to within less than 5° while in many cases greater limits are allowable. Almost every thermal property of matter has been suggested as a basis for the construction of pyrometers, but the thermo-electric type finds by far the widest application, and hence this paper will deal only with the principles, construction, and uses of this type of instrument. THERMOELECTRIC PYROMETRY.In the year 1821 Seebeek discovered that if the ends of two dissimilar metal wires were joined and one junction heated, a current flowed in the circuit, and the KMF (electro-motion force) set up could be measured by inserting a galvanometer at the cold junction. The phenomenon was not thoroughly investigated for many years, but, as the demand for high-temperature thermometers increased, several investigators, of whom Le Chatelier was one of the pioneers, successfully endeavoured to utilize the principle in pnometric construction. The couples which gave the most satisfactory results were discovered, improvements were made in material and design and the present-day type of instrument gradually evolved. The apparatus consists of three main parts, viz. (1) The thermo-couple itself of two dissimilar metal or alloy wires together at one end. (2) The leads which connect the terminal of the thermo-couple with the measuring instrument.

Jan 1, 1923

By Masami Nakamoto

Controlled thermolysis of gold(I) thiolate complex, [C14H29(CH3)3N][Au(SC12H25)2], at 180 °C for 5 h under an N2 atmosphere produces novel gold nanoparticles passivated by alkyl groups derived from the precursor complex, the TEM photograph of which shows spherical particles with average diameter 26 nm. Since Brust et al. reported the two-phase reduction of AuCl4 - by NaBH4 to afford monodispersed gold nanoparticles passivated by alkanethiolate ligands (1), plenty of preparative investigations on gold nanoparticles (2,3) and its surface modification (3,4) have appeared, because of their potential applications in microelectronics (5). However, those preparative methods generally involve the reduction of AuCl4 - by reducing agent NaBH4 in the presence of suitable organic stabilizers such as alkanethiol (1-4), phosphane (5), quarternary ammonium salts (6), surfactants (7) or polymers (8). On the other hand, O?Brien et al. recently reported the preparation of organically capped gold nanoparticles at 190 °C, where tri-n-octylphosphine oxide and/or n-octadecylamine are used both as a reaction medium and as a passivating ligand (6), but this procedure also needs NaBH4 as reducing agent. Our strategy of novel preparative method of gold nanoparticles is the combination of reductive elimination of thiolate ligands and simultaneous attachment of organic moiety on the growing nuclei. Gold(I) thiolate complexes with ammonium cations were useful for our preparative method. We now report the controlled thermolysis of gold(I) thiolate complexes, [R(CH3)3N][Au(SC12H25)2] and [R(CH3)3N][Au(SC6H4-p-R?)2] (R= C14H29, C12H25; R?= C8H17, CH3), under an N2 atmosphere, where the powder of gold(I) thiolate complexes completely melts to afford the precursor liquid and then the liquid gradually decomposes. In spite of no use of reducing agent and solvent, reduction reaction is thermochemically induced to afford novel gold nanoparticles passivated by alkyl groups rather than by alkanethiolate ligands. Figure 1a shows a typical transmission electron microscopy (TEM) image of gold nanoparticles prepared by thermolysis of [C14H29(CH3)3N][Au(SC12H25)2] at 180 °C for 5 h, indicating a controlled growth of spherical gold nanoparticles. As shown in Fig. 1b, these spherical gold nanoparticles display the size distribution ranging from 5 to 50 nm. Although the particle size is larger than that of thiol-derivatized gold nanoparticles (less than 5 nm) prepared by NaBH4 reduction (1-3), the aggregation of gold nuclei is smoothly regulated and the growth of core gold is limited to be 26 nm in average diameter in spite of thermal procedure.

Oct 1, 2003

By G. H. F. Gardner

The velocity and attenuation of elastic waves in sandstones were measured as a function of both pressure and fluid saturation. A large change occurs in these quantities if water is added and the rock is not compressed, but the change is small if the rock is subjected to a large overburden pressure. Measurements were made by vibrating cylindrical samples in both the extensional and torsional modes at frequencies up to 30,000 cycles/sec. Formulas were derived which enable the attenuation of dilatational waves in dry rocks to be deduced from the data. Similar experimental methods were used to investigate the properties of unconsolidated sands. Velocities were found to vary with the 1/4 power of the overburden pressure and attenuations to decrease with the 1/6 power. The effects of grain size, amplitude and fluid saturation were studied. Formulas by which the effects produced by a jacket around the sample may be calculated were derived. The practical application of these results to formation valuation is discussed. INTRODUCTION The attenuation of elastic waves in the earth has been of interest to the seismologist and geophysicist for many years, but only recently to the petroleum engineer. Engineering interest has been brought about by the success of velocity logging devices, for it is possible by modification of these instruments to measure the attenuation of sound waves in addition to their velocity and, hence, deduce the mobility of formation fluids as well as the porosities of the rocks which contain them. The main problem is to decide whether field measurements can be made with sufficient accuracy to be of practical use. This problem can only be solved after we know the magnitude of the attenuations which are typical of the earth at various depths. The logarithmic decrement of a fluid-saturated rock is the sum of a "sloshing" decrement and a "jostling" decrement, the former caused by the mobility of the fluid contained within the rock and the latter by the granular framework of the rock. Sloshing decrements can be calculated' using Biot's theory, but the jostling losses are less well understood. The present paper reports an experimental investigation of jostling losses in consolidated and uncon- solidated sands, particularly with respect to the effect of overburden pressure and fluid saturation. Born' showed that the decrement of a sandstone may increase dramatically when only a few per cent by weight of distilled water is added, and that the additional loss is proportional to the frequency of vibration. His measurements were made with no compressive stress on the framework of the rock. M. Gondouin3 investigated similar phenomena for fluid-saturated plasters but also did not compress the samples. In the present paper it is shown that compression of the framework reduces this effect, so that at depth the jostling decrement of a sandstone may be expected to be almost independent of fluid saturation and frequency. Decrements for many sedimentary rocks have been given by Volarovich,4 but all for the state of zero overburden pressure. Anomalously low velocities have been logged in shallow unconsolidated gas sands. Results of the present investigation confirm that these velocities are not caused by correspondingly high attenuations, because the jostling decrement in a packing of sand grains is small and much less than in a consolidated sandstone at the same depth. Velocities in sands have been measured by Tsareva5 and by Hardin6 as a function of pressure, but the corresponding decrements do not appear to have been measured previously. The widely used "resonant bar method" of measuring velocities and decrements was employed. Comments on variations of this technique have recently been published by McSkimmin.7 The main novelty of the present technique was the application of pressure to the samples. It was found possible to do this by placing the apparatus inside a pressure vessel, provided the conditions leading to large additional losses were avoided. These conditions are discussed below. EXPERIMENTAL TECHNIQUE Cylindrical samples were caused to vibrate in both the extensional and torsional mode of vibration and the amplitude of vibration was measured as a function of frequency in the neighborhood of a resonant frequency. The resonant frequency, fr, is related to the corresponding elastic modulus by the formulas where E and N are Young's modulus and the modulus of rigidity, p is the density of the sample, and A the wavelength of the vibration.

Jan 1, 1965