Search Documents

By M. L. Klohn

The Felder ore deposit is a 5,000,000-pound uranium deposit in the South Texas Coastal Plain. It occurs in the basal sand of an Oakville Formation (Miocene) alluvial system. The host sand is a carbonate-rich arkose which contains virtually no carbonaceous debris and has been reduced by the local introduction of hydrogen sulfide. The ore lies well within the reduced zone and occurs as coffinite and uraninite that fill interstices and coat and replace grains. The overall geometric configuration of the ore is that of a winged, crescentic ore roll. Weak mineralization extends the wings of the ore roll and gives greater expression to the roll character. Departures from the shape are controlled by discontinuities in bed- ding and by proximity of the ore to the surface. Associated with the uranium is a broad halo of anomalous molybdenum. Subsidiary mineralized trends suggest a pre-existing up-dip position for the main roll. Oxidation from the surface largely destroyed this previous roll by solubilization of uranium. Uranium subsequently migrated into favorably reduced sand and reprecipitated at the present roll position.

Jan 1, 1970

By A. B. Cox, L. W. Wark

In an earlier paper1 measurements of contact angles due to the effect of xanthates on mineral surfaces were reported. The solutions in which these measurements were made differed widely from those of modern flotation circuits. It is intended, however, by introducing, one at a time, the other principal reagents of flotation, to approach gradually the solution composition of flotation liquors. The work now described is an attempt to determine the effect of one of the most important of these reagents—namely, sodium cyanide—on the establishment of air-mineral contact. The work has been carried out for the following companies: Broken Hill South, North Broken Hill, Zinc Corporation, Electrolytic Zinc of Australasia, Mount Lyell Mining and Railway, and Burma Corporation. Since the effect of cyanide is inseparably connected with the alkalinity, the results cited below deal with the mutual effects of alkalis and cyanide. Alkalis alone exert a significant effect on the air-mineral contact but comparatively large amounts are required. Since the addition of a small amount of cyanide greatly decreases the degree of alkalinity necessary for the suppression of contact at surfaces of any of the minerals experimented with (except galena) and since alkalis are rarely used alone in practice, little attention has been paid to cyanide-free solutions. It was shown in the previous paper that, excluding the dixanthogen effect, whenever contact was practicable at all in an ethyl xanthate solution the angle of contact was 60". There is, therefore, less necessity to measure equilibrium contact angles; in fact, the experiments herein described have generally been conducted with a view to determining whether contact is possible and not to measuring the actual value of the contact angle. The separations which have generally to be effected in dealing with complex sulfide ores are: (1) galena from sphalerite, pyrite, etc.; (2) sphalerite from pyrite and/or gangue minerals; (3) copper minerals from pyrite and gangue minerals; (4) pyrite from gangue minerals; (5) chal-

Jan 1, 1935

By J. N. Economopoulos

The mining industry is becoming increasingly aware of environmental issues and has made big forward steps in the field of environmental management. Legislation, social pressure and competition introduced changes in the industry?s policies and practices in order to conform to the new standards of environmental performance. The paper addresses the need for an integrated and systematic approach to the issues of environmental management within the mining industry.

Jan 1, 2002

By Edward L. McHugh, Jami M. Girard

While less than 1% of reported accidents are associated with slope stability problems, slope failures were responsible for about 15% of all U.S. surface mine fatalities between 1995 and 2001. Small rockfalls, which may involve hand-sized rocks weighing only a few kilograms, can cause fatal injuries to workers away from the protection of large machinery. Massive highwall failures containing a million cubic meters of material or more can be fatal even for heavy equipment operators. As part of an ongoing study at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health, several remote-sensing technologies are being evaluated as tools to monitor slopes for hazards and to assess slope stability. Field tests of a hyper spectral imager were conducted to assess its value for improving geologic maps of potentially unstable alteration zones on mine slopes. An interferometric radar device capable of detecting very small displacements on slopes awaits final assembly and field testing. Computerized monitoring methods using images from digital and video cameras are being assessed for application to mine slope surveillance. These and other techniques will eventually provide new tools to augment current methods for monitoring ground control hazards in mines.

The figures given here were received through the courtesy of the Bataafsche Petroleum Maatschappij and the Standard-Vacuum. There is an increase in production for the year of approximately 4½ million barrels. In November the average production indicated that during the year 1935 the total production would probably exceed 50 rnillion barrels. To maintain this production, only 106 wells were drilled during the year, mainly in South Sumatra.

Jan 1, 1935

By J. D. Livingston, Bruce Chalmers, R. L. Fleischer, R. S. Davis

INTERACTION of dislocations on intersecting slip planes has long been considered a primary cause of work hardening in metals. Easy glide and low work-hardening rates have been observed experimentally only when single-crystal specimens were oriented so that one slip plane was initially favored. When single-crystal specimens have been oriented so that initially two or more slip planes were equally favored, high initial work-hardening rates have been observed. In a polycrsstalline aggregate, glide on five systems is in general necessary for a crystal to deform in conformity with the change in the shape imposed by the other crystals.* Only a small fraction of the crystals of a polycrystal will be oriented so that two

Jan 1, 1958

By Sobczyk

The article will present a comparison of classifications of resources according to the JORC Code System with Polish classification, basing on system used in Eastern Europe. The differences between these classifications are significant. The information about mineral resources in Poland is not comparable to the main international system of reporting reserves like JORC, SAMREC, and PERC. Although comparisons between these systems are used, the transfer of particular categories of resources from the Polish system into a JORC category is not simple. Basing on the examples of privatization of Polish coal companies through initial public offering on the Warsaw Stock Exchange, the current practices providing guidelines how to convert resources from the Polish classification to the JORC system are described. Such independent assessment of resources is necessary for development of Mineral Expert?s Report (MER or CPR) which is an integral attachment to the prospectus.

Aug 1, 2013

By John Hall

THE recently announced run of three years, nine months and eleven days made by a. crucible steel melting furnace of the Columbia Tool Steel Co., which is claimed as a. world's record, brings forcibly to our attention the great improvements that have been made in the design, construction and operation of the Siemen's regenerative crucible- melting furnace since its introduction in this country. Credit for this advance should be given to the furnace designer, the manufacturer of refractories, and the operators of the furnaces, whose persistent efforts and intelligent co-operation in attacking the problem have resulted so satisfactorily. There are three factors that determine the life of a crucible furnace, or any other furnace for that matter : Design, nature of refractories and conditions of operation; (including the nature of steel melted) and to some extent these factors are interdependent. Thus, for instance, if a crucible furnace is to lie operated single turn and allowed to cool off considerably at night, in order to save fuel, the use of clay-brick melting holes may be advisable, since silica brick is not well adapted to endure rep eated heating and cooling. But the total life of a clay-brick melting hole is necessarily short. Again, if local conditions such as danger of flood make necessary the building of the furnace largely above ground, so that the radiation of beat is promoted, the cooling down of the furnace over the week ends, when no steel is melted, will be considerable-and the contraction of the furnace that results tends to wrack it to pieces. The character of the metal being melted affects the life of the furnace to a great extent. Low-carbon steels and steels made from iron and charcoal require higher temperatures and much longer melting tune than high-carbon steel or steel made largely from scrap; the life of the furnace will be shorter, and the number of heats melted will be much less, when such materials are melted.

Jan 9, 1913

By Arthur Notman

THE year 1937 started off most hopefully for the metal industry but the prices for nonferrous metals declined after reaching a peak in the first quarter. E. & M. J. average prices for March were: -electrolytic copper f.o.b. refinery for domestic delivery 15.775c., lead 7.19c., and zinc 7.38c. There was the usual talk of shortages and the accompanying peak in the market prices of securities of producing companies. In retrospect it now appears that this was the peak of general security prices as well and of most commodity prices. On Dec. 1 copper was back to 11c., lead to 5c., and zinc to 5.5c. At the same time metal security prices had fallen to less than 40 per cent of their March highs. This has not been a purely domestic phenomenon. Metal prices have followed a similar course in London, in spite of the fact that in all three metals a tariff wall separates the domestic market from the foreign. There is nothing in the record to suggest that planning has so far had any stabilizing effect on prices. It is doubtful whether anybody will he found to claim credit for the planning. Strong evidence supports the conclusion that domestic demand for these and the other metals has been dammed back by the uncertainties confronting those who are considering long term construction commitments. This is particularly true with the public utilities, who are the largest consumers of copper and lead. If the plans were designed to maintain employment rather than to maintain political control of the Government, it would appear that they should be discarded. The course of the steel industry has been followed so closely in the press that no comment is necessary to indicate its similarity.

Jan 1, 1938

By Gungor Tuncer, Erhan Bakirci, Ali Kahriman, Atilla Ozmen, O. Nuri Ucan, Savas Gorgun

There are several methods for demolition of structures but most of them depend mostly on conventional ways of using machines for breaking and crushing structural elements. However the need for lots of work force, expense and extreme amount of time for demolition, made most of these methods non-popular nowadays. Therefore, trials to accomplish a more economic and less time taking method lasted with the use of blasting. By applying controlled blasting on a suitable structure, the structure can collapse and break down to pieces in very short period of time, with no extra work force and cost. In spite of advantages of explosive demolition, the potential danger of explosives and the damage that the blasting may cause to surrondings, if not controlled properly, made people timid to the method especially in urban areas. Therefore, the pre-assumption by computational analysis has become an essential matter in the process.

Jan 1, 2002

By A. W. Henderson

Methods for converting WOCl4 to WCle were investigated in small-scale, laboratory apparatus to devise a method for preparing pure WCls suitable for conversion to tungsten metal. Chlorine, COCI2, and CCI4, alone and in combination with various forms of carbon, were tested as chlorinating agents at various temperatures. More than 95 percent conversion of WOCl4 to WCls was achieved with all reagents at 8000 C in the presence of activated carbon. Only CCl4 maintained its effectiveness in the absence of carbon at 800° C. The effectiveness of carbon was found to be related directly to its surface area.

Jan 1, 1968

By Lucy Villena

El presente trabajo se detalla los resultados más importantes de los estudios realizados de la mineralogía (mena y ganga) y microtermometría con el objetivo de caracterizar los flujos mineralizantes y la dirección de la migración de los fluidos mediante los paleoisotermas de la veta 1. La veta polimetálica es comprendida Pb-Zn-Ag compuestas por rocas volcánicas (andesita a basáltica), cuyo control estructural principal está dado por fallas tensionales de dirección NE-SO, causadas por el movimiento sinestral de fallas Chonta y Huachocolpa- Huancavelica. La composición de las menas reconocidas en la veta 1 corresponde a esfalerita, galena, tetraedrita, bournonita, acantita-argentita y calcopirita, en una ganga conformada por cuarzo, calcita, barita, adularia y yeso. En las muestras de la veta estudiada, los estudios microtermométricos fueron realizados en los cristales de baritina, calcita, cuarzo y esfalerita asociada a la mineralización. Se observan inclusiones fluidas bifásicas acuosas (LH2O + v H2O) las cuales poseen al menos tres eventos mineralizantes según temperaturas de homogeneización y salinidad % equivalente en peso, los fluidos mineralizantes son moderadamente salinos, sugeriendo un ambiente de tipo epitermal.

Sep 21, 2015

By James F. McDivitt

The mineral industry of today is faced with a number of dilemmas, not the least of which grows out of the series of related facts-world mineral consumption is growing, and is expected to continue to grow; maintaining adequate capacity to meet needs will require very great capital investment over the next decades, investment which must be measured in billions of dollars; much of the new production must come from remote and relatively underdeveloped countries; many of the areas in which such development must take place are not areas in which private capital enters without some trepidation. There are real problems in financing new mineral development-problems which have occupied the thoughts of many in the industry. One group which is currently providing part of the answer, and perhaps pointing the way to further progress in the future, is the World Bank. Loans from the World Bank are arranged usually for countries which are attempting to develop their economies through expanded industrial production. More often than not they are for the development of electric power projects or transportation facilities. Although we consider the mineral industries to be basic factors in industrial development and very important factors in the early stages of development of a country, few of these loans are for mineral development-no more than a half dozen out of a total of well over 300 loans which have been granted to date. Yet the World Bank has played a far more important part in world mineral development than these figures would indicate. The few loans for mineral development which it has made are important, but of considerably greater importance are the secondary effects of many of the non-mineral development loans and some of the special services which the Bank also offers.

Jan 5, 1963

By Yanfa Gao

Abstract In order to control and reduce ground subsidence due to coal mining, and to protect building, railway and other surface construction, a new subsidence control method is proposed. Ground subsidence is reduced by grouting bed separations in overlying strata with fine-coal ash. Engineering application tests have been performed for 5 years in Tangshan Coal Mine. Kailuan Group Corporation. China. The technology has been applied to 4 fully mechanized sublevel caving mining faces. Its effect in reducing subsidence has been significant. The technology including grouting engineering design method and ground subsidence prediction theory is introduced in detail. Keywords: overlying strata separation, multi-layer grouting, subsidence control

Jan 1, 2002

By C. Arson

We modeled mode I fracture in shale with an equivalent damage zone (CDM), a cohesive zone (CZM) and discontinuous enrichment functions (XFEM). In the Differential Stress Induced Damage model (DSID model) used in the continuum approach the total work input is equal to the sum of the energy released by crack debonding, the energy dissipated by crack opening, and the elastic strain energy stored in the bulk outside of the damage zone. In CZM and XFEM, the overall stiffness of the rock mass in the process zone drops as soon as the fracture starts propagating (unstable fracture propagation), whereas rock elastic properties in the CDM equivalent damage zone evolve smoothly with the displacement imposed at the boundary of the domain. In the CZM and XFEM, fracture propagation stabilizes after a turning point: this point coincides with damage initiation in the DSID model. As a result, the total energy of the rock mass calculated with CDM is about twice as large as in CZM and XFEM. The relative energy components of the rock mass are in the same order of magnitude and follow the same trends in the three models. This numerical study compares the evolution of dissipated energy potentials during mode I fracture propagation, and is expected to provide a basis to predict the amount of energy released by discrete fracture growth vs. damage propagation in the fracture process zone.

Jan 1, 2015

By Asok Kumar Das

"In steel making ferroalloys occupies a commanding role for production of varied quality of steel. Ferroalloys enable alloying elements such as chromium, silicon, manganese, vanadium etc to be safely and economically introduced into metallurgical processes thus giving certain desirable properties of the alloyed metal. Their importance grew with the progress of the steel metallurgy which implied more diversified alloying elements, in better controlled quantities, in purer steel. The ferroalloy industry became a key supplier to the steel industry. Production of ferroalloys generally involves the use of Electric Arc furnace(EAF) into which raw materials(e.g. various metal ores, quartz, coke, lime etc ) with relatively fluctuating physical compositions are loaded. Due to this, one of the major environmental impacts of producing ferroalloys is the emission of dust and fume from the smelting process. INTRODUCTIONFerro Alloys are essential ingredients used for refining, de-oxidation, desulphurization and alloying addition in the production of different types of steel and hence Ferro Alloy industry forms a back bone of iron and steel in the world. Indian ferro alloy industry is more than 45 years old. It produces most of the bulk ferro alloys and a large number of special ferro alloys. The present installed capacity of the Indian ferro alloy industry is sufficient to meet the requirement of existing level of indigenous steel production of about 46 million tonnes. Revised National Steel Policy – 2008 envisages production of more than 100 million tonnes of steel by the year 2011-12, at proportionate annual growth rate per annum. The focus of the policy is to achieve global competitiveness not only in terms of cost, quality and product-mix but also in terms of global benchmarks of efficiency and productivity. In order to achieve the objectives of National Steel Policy and also to meet the requirement of ferro alloys, the Indian Ferro Alloy Industry has to gear up in terms of enhancement in production capacity, sourcing of raw materials, up gradation of technology, improvement in productivity, automation / mechanization, customer satisfaction etc."

Jan 1, 2008

By C. W. Robinson

El presente texto describe el problema del nacionalismo de las realidades de la expropiación latinoamericana. Uno de los principales problemas radica en las relaciones de Estados Unidos con América Latina - en tanto el nacionalismo genera una sensibilidad emocional y política que contrapone la posición del país inversionista extranjero. Por ello, se debe eliminar el aspecto político o desnacionalizar las inversiones extranjerases necesario, de forma que el desarrollo de consorcios para inversiones de mayor envergadura formados por participantes de dos o más naciones, puede reducir el riesgo de ataque político basado en el argumento de 'invasión de soberanía".

Jul 1, 1972

By Ted C. Briggs

The Bureau of Mines is evaluating the thermodynamic properties of helium and helium-containing mixtures. Twenty-two compressibility runs were made with helium at 0° C and pressures to 800 atmospheres using a Burnett-type apparatus. Data from the 22 runs were treated simultaneously and as separate runs while different functional forms and weighting factors were used. A fourth-degree-polynomial equation in the pressure gives a statistically satisfactory representation of the compressibility factor when the data are treated simultaneously and a weighting factor of Pr-3/4 is used. The second virial coefficient of helium at 0° C from this investigation is 11.997±0.015 cm3 mole-1. The stated uncertainty is the random error standard deviation. Compressibility factors determined by this investigation are precise to better than 0.01 percent and are believed to be accurate to better than 0.02 percent.

Jan 1, 1969

By W. Rostoker, H. Nichols

The embrittlement by mercury of aluminum alloys in various states of anneal, cold work, and aging has been studied. It is shown that single phase and non-precipitation hardened structures irrespective of de,pee of prior cold work demonstrate some small measure of yielding before fracture occurs. Sub-yield-stress failure is confined to the aged state, and embrittlement is accentuated by small plastic prestrains. With large plastic pyestrains, embrittle~nent is progressively reduced. In previous work' it was shown that the propensity of commercial aluminum alloys for embrittlement when wetted with mercury seems to be related primarily to the intrinsic strength in the normal un-wetted condition. The data from a large number of commercial alloys in various states of anneal, cold work, and/or aging gave a generalized relationship. At low strength levels, the wetted fracture strength increases proportionately to the increase in tensile strength; but above 65,000 psi normal ultimate strength, the trend is abruptly reversed, and the wetted fracture stress decreases proportionately to the increase in tensile strength. This paper will demonstrate that the simple character of this relationship between normal tensile strength and wetted fracture strength is fortuitous. It will be shown that structure and thermal-mechanical history are clearly relevant factors. The term brittle fracture has been used to connote the geometry of the fracture surface (transverse vs shear plane) or the negligible extent of preceding plastic strain. At its maximum effectiveness, liquid metal embrittlement can satisfy both criteria—fracture transverse to the axis of tension and without observable plastic strain. In this paper, brittle fracture will signify failure at stresses below the engi-

Jan 1, 1962

About 1300 members and guests attended the Seventh Annual Mid-winter Convention of the American Institute of Electrical Engineers, which was held in the Engineering Societies' Building, New York, on Feb. 19 to 21. The opening session was a joint session with the American Institute of Mining Engineers, when welding was discussed. The various phases of standardization in engineering work were discussed by President Comfort A. Adams at the Thursday morning session. Thursday afternoon was spent in visiting. Some of the guests visited the Brooklyn Navy Yards, where they inspected the power plant, shops, dry, docks, etc. ; others visited the Bell System Laboratories of the Western Electric Co. The papers at the various technical sessions provoked considerable

Jan 4, 1919