Search Documents

By R. Matikainen

Since the Brundtland Commission in 1987, the use of natural resources has been an issue of global concern. Minerals are among the most important Earth resources and will definitely be essential for the development of societies also in future. Increasing scientific effort is needed not only to discover new deposits, but also to promote resource management in ecologically and socially sound way. Sustainable resource management is essentially a multidisciplinary challenge of developing life-cycle analysis and recycling of non-renewable resources from local to global scale. It offers great opportunities for geological surveys not only in EU, but all over the world to contribute positively to the welfare and sustainability of societies.

Jan 1, 2003

Economic mathematical methods have been developed and applied in the design, planning, development and managing stages in the mining industry. Economic and technological efficiency is achieved with the aid of a large range of probability models, which are used to enable decisions to be made progressively during the different stages. The entire operation is considered as a total system made up of sub- systems and the models representing these are consecutively interrelated with each other. Algorithms and programmes representing the economic mathematical models for all the stages involved were tested and were found to be applicable to the various important mines in the Donetsk basin. Currently, these models are accepted and widely used.

Jan 1, 1977

By J. M. Skeaff

"The main solution, ore and residue pulp streams in the Rio Algom Quirke I uranium mill at Elliot Lake have been sampled and analyzed for radium-226. Analysis of the ore and leached residues indicates that Ra-226 dissolves and precipitates within the first pachuca tank. A maximum of approximately 0.2% of the Ra-226 in the ore remains in solution during leaching.IntroductionConcern over the acid drainage and radionuclide dissolution problems associated with uranium tailings disposal sites in Canada has prompted investigation into methods for improving current uranium processing practice.Present commercial practice usually involves leaching of the uranium ore with sulphuric acid, ion-exchange separation of the uranyl sulphate complex from the leach liquor and"" precipitation of the uranium as yellowcake. Daughter products of U-238, such as Th-230, Pb-21O and Ra-226 remain with the tailings and undergo long-term dissolution.Table I summarizes the probable behaviour of the radionuclides during milling. The concern here is with Ra-226, because it will deposit in the bones if ingested and is ""thus considered a serious health hazard(1), Similarly, Po-218 and Bi-214, which are daughter products of Rn-222, can be retained in the lungs and are considered to be the principal sources of radiation dosage(2) arising from the inhalation of Rn-222. Previous investigations(3-9l indicate or imply that Ra-226 undergoes redistribution during milling. However, detailed published information on the behaviour of Ra-226 in the uranium milling process appears to be lacking. A knowledge of the behaviour of Ra-226 in uranium mills, particularly during leaching, could lead to improved methods for its control.This paper reports the occurrence of Ra-226 in the Rio Algom mill. The main objectives of the study were to determine (1) the distribution of Ra-226 within the solids, (2) at what point, and how rapidly, redistribution occurs and (3) whether there are high concentrations of Ra-226 in solution."

Jan 1, 1981

By W. P. Sykes

In an earlier paper1 the composition-temperature limits of the gamma iron phase in the iron-tungsten system were reported as approximated by thermal analyses. At that time no attempt was made to develop metallographic evidence of the coexistence of two phases in the iron-rich solid solution at temperatures between 900" C. and 1400" C.

Jan 1, 1931

By Yoshitaka Hosoi

The survey of the cobalt-rich crust of the Republic of the Marshall Islands was carried out in 1996 and 1998, as the cooperative study project between Japan and SOPAC member countries, and at the thirteen seamounts, seafloor topographic maps and acoustic reflection intensity distribution images by MBES were obtained, and the collection of samples by dredging was conducted. On the basis of the previous results, three seamounts, MS01, MS11 and MS12 were selected for the 2002 year survey, and drilling by BMS (deep sea boring system) was conducted there, to understand the occurrence of cobalt-rich crust. At the same time, environmental survey was carried out to make clear the environmental characteristics of the area. The summary of the survey will be reported.

Jan 1, 2003

By Jônatas Targino Araujo

As fibras de bambu são ricas em celulose, hemicelulose e lignina. Devido ás suas ótimas propriedades mecânicas conforme solicitação percebeu a abundância de celulose e sua respectiva orientação nas regiões dos entrenós, indicando elevado teor de celulose. Nosso trabalho tem o objetivo de extrair nanocelulose dessa região do bambu, desenvolvendo uma metodologia eficiente na sua produção. As nanopartículas foram obtidas por hidrólise ácida a 64% após lavagem com NaOH e branqueamento com H2O2 e NaOH. As caracterizações das amostras foram feitas com TG, DTG, IFTR e tamanho de partícula por Potencial Zeta. Foram observados dois eventos na análise DTG: um em 54°C correspondente a perca de água e em 330 °C correspondente a degradação da celulose. Os tamanhos das partículas em Potencial Zeta obtiveram picos em 257,1 nm (79,6%) e 67,9 nm (15,6%).

Oct 30, 2017

By Victor Bridi Telles

Este trabalho teve por objetivo estudar a redução por hidrogênio de sínteres produzidos com coque e carvão vegetal. Para isso, foram realizados 6 ensaios de sinterização substituindo o coque por carvão vegetal como combustível do processo. As substituições foram de 0%, 8%, 16%, 25%, 50% e 100%. As amostras com substituições de 0%, 50% e 100% foram reduzidas em termobalança, durante 6 horas, em temperatura de 1000°C, utilizando uma mistura de gases contendo Argônio – 10% Hidrogênio. Os resultados mostraram que, para as misturas produzidas, o sínter fabricado com carvão vegetal diminuiu os índices de produção da sinterização e de resistência do sínter. Contudo, o sínter produzido utilizando somente carvão vegetal como combustível, apresentou maior redutibilidade.

Oct 30, 2017

By Donald N. H. Chi

This Bureau of Mines report is concerned with a theoretical study of the aerodynamic response of a single mine entry to flame-induced disturbance. The unsteady, one/dimensional, compressible flow equations were solved using the method of characteristics. This study was primarily undertaken to determine the feasibility of extending the method of characteristics to study the aero-dynamic response of complex mine networks. It was demonstrated that although the technique has merit in studying the complex wave interaction in single entries, it appears to be too unwieldly and too expensive for network analysis. Effort was also directed at a further study of the dispersion and filtering characteristic of aerodynamic disturbances in mine passageways.

Jan 1, 1975

By M. Menegaki

Restoration of abandoned mine sites is still one of the weak points of mining practice. The latter stands especially for the case of the surface coal and lignite exploitations, where the extended size of the disturbed land and the drastic changes to the geomorphologic features do not facilitate the implementation of a cost effective and environmentally sound reclamation plan. The paper examines the parameters involved towards the legal requirements for the reclamation of the first lignite exploitation in Greece, namely the ?Plakes? mine, located at Euboea, due to the particularities of the site. Then an integrated redesign procedure is presented, aiming at minimizing aesthetic degradation, confronting technical difficulties and preparing the site to accept new uses.

Jan 1, 2005

By Walter H. Bruckner, George B. Clark

Since the end of World War 11 interest has been increasing in the use of shaped charges in the mining industry and in other industries using explosives for blasting purposes. Shaped charges employ the principle known as the "Munroe effect," which was discovered by Charles E. Munroe more than 50 years ago (in 1888). Details of their design have been explained elsewhere.1,2,3 Fig I shows the essential features of design of two types of shaped charges (with conical and hemispherical cavities) and a schematic sketch of their action upon detonation. The following discussion deals with the behavior of the metal in the cavity liners when they are subjected to intense Pressures exerted when the explosive charge is detonated. Among the conclusions reached in research on shaped explosive charges, the following have been established conceming cavity liners:1'2 I. The optimum wall thickness of a conical cavity liner is dependent upon the apex angle of the cone as well as On the base diameter of the charge. Acute apex angles require thinner walls for optimum perfonnance and more obtuse angles require thicker walls for the same base diameter. '. Cones were more effective in forming a penetrating jet when the walls were tapered; that is, the thickness of the wall of the cone increased from the apex down. 3. The physical and mechanical properties of metals have a marked effect upon their performance as cavity-liner material. Boiling point, ductility, malleability, ten-sile strength, and hardness are among the properties that influence the effectiveness of a metal used as a cavity liner. Lead, for example, makes a wide, flat crater in steel plates. Aluminum makes a deeper crater than lead, and an aluminum alloy having a high tensile strength makes a deeper hole, but slightly smaller in diameter. Cast iron makes a deep, narrow hole. These findings, together with the following analysis under Metallographic Survey of slug, offer solutions to many of the problems involved in solving the mechanism of the formation of Munroe jets. It has been fairly well established that cavity liners collapse in a manner similar to that indicated in Fig 2, Conical liners are known to collapse upon themselves while hemispherical liners are believed to turn inside out in the process of jet formation. The first has been definitely proved by recovery of collapsed portions of cones, while liners from partly detonated charges show that hemispheres may turn inside out. Fig 3 shows a sketch of a recovered slug from a 6-in. shaped charge using a 45" cone made of cast iron. (This size of charge drilled holes up to 3 ft in depth in solid granodiorite.)

Jan 1, 1949

By Evelyn Dayrell Lopes Júnior

A capacidade de alimentação de sistemas de fundição é uma das características tecnológicas que está correlacionada a resultados qualitativos negativos, como porosidades e deformações geométricas dos produtos fundidos. As ligas com suas características são parte fundamental do processo de alimentação. A metodologia de caracterização da capacidade de alimentação por meio da coquilha Tatur foi utilizada nesse trabalho, para a qual foram desenvolvidos novos processos de dosagem da liga líquida, com o objetivo de prover maior repetitividade, e consequentemente, maior coerência morfológica das amostras produzidas. Para isso, foram desenvolvidos dois novos métodos de dosagem, chamados “método de dosagem dinâmica” e “método de pré-dosagem”. Esses foram testados e analisados, sendo suas amostras avaliadas comparativamente com o padrão morfológico teórico. O objetivo da obtenção de amostras coerentes foi atingido, sendo evidenciadas a grande influência das variáveis presentes na etapa de vazamento sobre os resultados das amostras obtidas.

Aug 17, 2017

By William J. Millard

The Island of Trinidad has much the same geological history as the continent of South America. There are present in this area Cretaceous, Tertiary and Quaternary rocks, which were deposited in a basin covering eastern Venezuela and Trinidad, very much as rocks of the same age were deposited in the Maracaibo Basin in western Venezuela. Along the north coast there are metamorphosed and semimetamorphosed Cretaceous rocks which are found as semicrystalline limestone, schists and quartzites, etc. Both the Cretaceous and Tertiary rocks are petroliferous and are responsible for the production of oil in Trinidad and eastern Venezuela. The geological column in the oil-bearing region of Trinidad is shown below.

Jan 1, 1931

By J. B. Hiskey, V. P. Atluri

Resin-in-leach (RIL) cyanidation experiments were performed on a refractory carbonaceous gold ore. The objective of this investigation was to determine if strong-base ion exchange resins could adsorb the soluble aurocyanide complex in preference to natural "preg robbing" organic constituents. Direct cyanidation of the carbonaceous gold ore used in this study resulted in less than 2% gold extraction in 24 hr. RIL cyanidation resulted in about 70% gold recovery onto the resin. Kinetic experiments indicated that 50% of the gold is extracted after 1 hr of leaching. Resin breakage was investigated for as-received and preattrited resins. Similar results were obtained with three different strong base resins.

Jan 1, 1990

By Karl H. Gehring

According to the increasing importance of boom type roadheaders in tunnelling essential problems occuring in the application of these machines are dealt with. Based on a chart including the various stages for decicion finding the excavation method of underground cavities, both the technical limits and economic criteria are discussed in order to determine the range of applicability of roadheaders. Giving examples-the numerous developments in the fields of pick and cutting technology, performance data of boom type roadheaders in hard rock, safety technology and increase in the machines' degree of utilization, research and development of VA is illustrated. Two topic operation examples show partial aspects of the various tendencies of development.

Jan 1, 1981

By Lawrence W. Teufel

A method to determine in situ stress directions and magnitudes from anelastic strain recovery measurements of oriented core has been used to determine the principal horizontal in situ stresses in the Rollins Sandstone in a deep well near Rifle, Colorado. The principal horizontal stress directions were determined directly from the principal horizontal strain recovery directions. The principal horizontal stress magnitudes were calculated from the principal strain recovery magnitudes, overburden stress, and Poison's ratio of the rock using a viscoelastic model. The accuracy of the in situ stress directions and magnitudes determined from anelastic strain recovery measurements was substantiated by a direct comparison with open-hole hydraulic fracture stress measurements. The anelastic strain recovery method predicted the magnitudes of the maximum and minimum horizontal principal stresses to be 54.5 MPa and 51.9 MPa, respectively; with an azimuth of N63ºW ± 8º for the maximum horizontal stress. The hydraulic fracture stress measurements yielded maximum and minimum horizontal principal stress magnitudes of 49.6 MPa and 46.8 MPa, respectively. The azimuth of the maximum horizontal stress ranged from N50ºW to N70°W.

Jan 1, 1984

By Arthur B. Arnold, Curtis T. Scott

The Blue Mountain Tunnel is a part of the Sultan River Hydroelectric Project. The Sultan Project is in the Cascade Mountain Range, approximately 56 km (35 mi) northeast of Seattle, Washington. The geology is structurally complex, consisting of graywacke and argillite, with lesser amounts of metaigneous rocks. The tunnel, excavated with a tunnel boring machine (TBM), is 4.32 m (14 it) in diameter and 6.3 km (3.9 mi) long. The average 24 hour advance was 41 m (134 it) with a maximum of 71 m (234 it). The tunnel is essentially unlined except for 383 m (1,257 it) in a low cover area and in the rocktrap. Inspection of the tunnel after one year of operation showed it to be in good condition with only a minor amount of rock debris in the rocktrap.

Jan 1, 1987

By Linkson PB

The presence of residual cyanide in mine tailings and fill sands may, under specific circumstances, lead to acute and/or chronic cyanide poisoning of the environment and individuals. In this paper, the nature of cyanide contained in mine tailings is discussed, along with the circumstances under which such cyanide would become a hazard. A number of methods for cyanide degradation are reviewed in the paper, with special emphasis being placed on biological degradation (due to its low costs and the non toxic nature of the degradation process itself). Recommendations are made as to the best methods of setting up a biological degradation system, for use in mining Situations.

Jan 1, 1987

By Donald C. Trueblood

Since the Surface Mining Control and Reclamation Act (SMCRA) was passed in 1977, coal mine reclamation has been restricted from utilizing bluff-1ike features in permanent reclamation. This restriction is based on those provisions of SMCRA which require the elimination of all highwalls. In 1987, the Wyoming Mi ni ng Association began an effort to acquire the ability for coal mines to utilize bluffs in permanent reclamation for the purpose of enhancing the post-mining land use. The regulatory reform approach being uti1ized includes formation of a work group with members from industry, government, agriculture, and environmental organizations to prepare a proposal. Advantages of this approach are discussed.

Jan 1, 1989

By K. G. Sutterer, R. J. Sweigard, U. Graham, T. C. Hopkins

The prevalent use of coal combustion byproducts in engineering applications has been with Class C and Class F fly ash as admixtures in structural concrete. But, the use of fly ash and bottom ash byproducts from modern desulfurization processes is receiving increased attention. The University of Kentucky has been conducting research into civil- and mining-engineering applications of these products. The studies have included extensive investigation of the geomechanical behavior of the materials and the effect of mineralogy on this behavior. These studies indicate important mineralogical considerations in the selection of materials for a specific application and highlight the importance of quality control before and during usage on specific projects.

Jan 1, 1998

By M. J. Scoble, W. J. P. Leigh

This paper aims to characterise the forms of slope instability incident in surface coal mines in Britain. These are related to observed controlling factors, with particular reference being given to slope geometry and structure. The work is based on specific data collection programmes considering actual stable and unstable mine slopes. Reference is made to field examples.

Jan 1, 1982