Search Documents

By Bruce H. Van Brunt, Danny L. Taylor

Estimation of local recovered tonnage and its grade above a cutoff is of paramount importance during the exploration and development stages of any mineral deposit. The spatial dis- tribution of grades as well as the cumulative distribution must be defined. In this paper, Probability Kriging, an estimator based upon rank order statistics and the estimation of the distribution of point grades within a panel, is applied to the Manhattan gold deposit. Mapping the conditional probabilities that estimated panel grades exceed a cutoff is useful to the understanding of the distribution of mineralization in a structurally controlled gold deposit.

Jan 1, 1989

By George W. Mitchell

THE property of Eureka Corp. Ltd. is located in the approximate geographic center of Nevada, 2 miles from Eureka, the county seat. The great sources of power, the Colorado, Snake, and Salmon Rivers and the rivers of northern California, are 300 to 500 miles distant, and no lines serve areas closer than 150 miles. Fuel for diesel and steam generation is available in Utah, 300 to 400 miles to the east. Eureka's railhead is 80 miles north where two trunk lines cross the county. A spur line serves Ely, 77 miles east. Good highways connect Eureka to the railheads.

Jan 8, 1953

By M. Cross

The main results from a programme of theoretical work on various aspects of the pelletizing operation are presented. This paper is primarily concerned with the modelling of: (i) The balling drum operation. A model is outlined which clearly demonstrates the characteristic surging behaviour of the balling circuit. It is used first in a control analysis and, subsequently, in the design and testing of various control schemes. (ii)The grate-kiln-cooler induration process. Models describing each of the constituent processes are outlined and a composite model of the whole induration process presented. The main results from each of these models are discussed.

Jan 1, 1977

By Alfred Weiss

The business world of tomorrow will experience a major change in its data communication systems, with the mineral industry being among those to feel the greatest impact of this change. This development can be expected to occur over the next two decades at a steadily increasing tempo. One major factor prompting this transformation is the fact that technological knowledge is doubling approximately every five years. Moreover, industry is becoming more and more dependent upon the flow and processing of information in its long-range planning, while government requirements and regulations demand increasingly detailed and precise information on plant operations.

Jan 1, 1971

The economic significance of a fundamental understanding of the mineral pyrrhotite is dis- cussed. Particular emphasis is placed on the relationship of other sulphide minerals to the pyrrhotite when it is the major sulphide mineral present in an ore body. Studies of the Kambalda nickel deposit are used to give a better under- standing of (a) the genesis and other character- istics of a particular ore body (b) the textural relationships between pyrrhotite and other sul- phide minerals (c) magnetic properties of natural pyrrhotite, and (e) the oxidation and supergene processes that take place in a sulphide ore body.

Jan 1, 1972

By W. E. Hall

The Darwin mining district of California, 160 miles north of Los Angeles, has yielded an estimated $45 million in lead, silver, zinc, and copper since 1875. The deposits are in silicated limestone of Penn-sylvanian and Permian age close to a stock of horn-blende-biotite-quartz monzonite. Steep left-lateral strike-slip faults that strike N 50o 70o E served as feeder channels for the ore solutions, and minor folds, favorable beds, and faults close to the feeder channels localized the orebodies. The orebodies are irregular, steep, pipe-like replacements that cut across bedding, bedding replacements, and fissure fillings in a calc-silicate country rock consisting mainly of wollastonite, grossularite-andradite garnet, idocrase, and diop-side. Near surface the ore consists of a soft, crumbly mass of cerussite, hemimorphite, jarosite, limonite, and some secondary copper minerals. The primary ore consists of galena, sphalerite, pyrite, pyrrhotite, and chalcopyrite with smaller amounts of andorite, matildite, scheelite, tetrahedrite, and a high silver-lead-bismuth-selenium-bearing galena. Preliminary X-ray fluorescence study of the primary ore has indicated unusually high concentrations of bismuth, selenium, and silver in galena from certain parts of the mine. One phase of this study concerns the distribution of these elements. Twenty-two samples of galena and thirty of sphal- erite have been purified and analyzed or are being analyzed. The selenium in 21 samples of galena ranges from 0.0045 to 2.11 pct; four contain more than 1 pct. These four samples were collected from the Essex orebody, where most of the selenium is concentrated. Three are from high-grade, near-surface ore, and one is from the 700 level. Four of the seven analyzed galena samples from the Thompson workings immediately north of the Essex orebody contain 0.29 to 0.74 pct Se; the others show less than 0.05 pct. Galena from the Defiance workings about 2000 ft south of the Essex has less than 0.03 pct Se. The selenium-bearing galena also contains concentrations of bismuth and silver. Preliminary spectographic analyses indicate as much as 3 pct Bi and more than 1 pct Ag in galena with high selenium content. Antimony is the only other minor element present in galena in amounts greater than 0.02 pct; most galena contains between 0.1 and 0.2 pct and the maximum is 0.72 pct. A second phase of the study is an attempt to determine the temperature range of the formation of the ore. The iron content of sphalerite deposited in equilibrium with pyrrhotite is being used as a geologic thermometer as it is a function of the temperature of deposition of the ore.' Preliminary results indicate temperature range from 430°C in replacement orebodies in the Defiance workings to 180°C in shallow fissure fillings.

Jan 1, 1960

AS I told you before in the treatise on ores, once these are found (whether they are ores of metals or semiminerals) it is necessary to assay them in order to know what is in them, since the judgment of the sight is not sufficient for recognizing the quantity or even what substance they contain. For this reason, it is necessary to come to assaying and, with the knowledge of experience, to weigh their virtues and to proceed with the work or withdraw from it and its expense; and also through knowledge to make provision for their defects if some evilness harms the ores. For if you should have need of a thing that would help them and should not find it, all that you have done would be lost; and, on the other hand, if you should find that the ores are abundant and rich and easy to smelt, you take courage to continue without respect for anything. Therefore, in the following book I shall tell you first in general how the assay of all the metals should be made. I shall enlarge in particular on silver more than on any of the others since it is more important. Then I shall tell you how the ores should be prepared for smelting and also how blast furnaces and other furnaces for smelting such ores should be constructed, and finally how all elemental mixtures of metals are to be separated one from the other with the ability and power of art, and how they are reduced to their final perfection and fineness according to their species.

Jan 1, 1942

By Jack Fox

It is some time since these columns have contained a report to the members on just what is doing in the Society of Mining Engineers. Accordingly, even though it is now a month and a half after the Annual Meeting in Denver, it seems that a report on what transpired at the SME Board Meeting there is in order. First off, I'd like to say that the Members of the Society of Mining Engineers can be justly proud of their representatives on the SME Board of Directors. Of 21 members and officers on the "Old" Board of Directors, 19 were present. President Brower Dellinger chaired the "Old" Board Meeting. Of the 21 members on the "New" Board of Directors, every single one was present. James Boyd, the outgoing AIME President, attended and expressed his appreciation of the support that the Society of Mining Engineers had given him during his year as President of AIME. Members Multiply Robert S. Shoemaker, Chairman of the SME Membership Committee, pointed out that based on figures available, the Society of Mining Engineers had a net gain of 523 members during 1969 while SPE had a 490 net gain and The Metallurgical Society a net loss of 159. This is probably the first time in the last 20 years that anyone has exceeded the SPE net gain in membership. While SME still has a way to go to surpass the Society of Petroleum Engineers in number of members, we did have, on December 1, 1969, 16,369 members. However, 419 were dropped at the end of that month leaving us with a net for the year of 15,950.

Jan 1, 1970

By Ruilin Lang

This paper presents an application of 3-D plots and non-linear regressions to define a sitespecific form of the charge weight scaled distance. The PPV (PPA) of single hole blasts is normally considered as a function of two independent variables - the charge weight and the distance. It is of great importance to obtain the relationship of the function accurately for a concerned site in terms of blast vibration analysis and modeling. However, in pre-computer time it was difficult to plot 3-D graphs. Consequently, a charge weight scaled distance was used to plot the PPV (or PPA) against the scaled distance as 2-D graphs. Blast vibration investigators use several forms of the charge weight scaled distances to plot data. We can exemplify them with the cube root of charge weight scaled distance, the square root of charge weight scaled distance, and other forms (Hossaini and Sen, 2004). Each of these scaled distances assumes relative contributions of the charge weight and the distance to the vibration attenuation. For example, the charge weight is assumed to have a less contribution to vibration in the cube root scaled distance than it is assumed in the square-root scaled distance. In reality, for different sites the relative contribution of the charge weight and the distance may be different and site-specific. This may explain that in some cases, the blast vibration data plots using these charge weight scaled distances are scattered. This could be largely due to the fact that the definition of the form of the charge weight scaled distance is not adequate for the particular site condition.

Jan 1, 2006

By P. Banerjee, P. Dash, S. Sriramoju, A. Suresh, R. Lingam, T. Ray

"One single property that influences the quality and market value of coal to the maximum extent is the ash content. The lower the coal ash higher is the energy utilization and potential for different applications. Even though Indian coal washeries aspire to produce coal with low ash, the intimate distribution pattern of ash bearing minerals in the coal matrix becomes the real bottleneck, as it brings down the clean coal yield to the impractical value. Because of this fact, most of the Indian washeries are operated to produce coal with 14-15% ash content at the yield of around 40%. In this context, with an objective to produce low ash coal at higher yield, a novel chemical beneficiation route has been explored to demineralize the high ash containing Indian coals. In this present work, the production of low ash clean coal from high ash Indian coals using chemical leaching process has been studied at pilot plant level. The leaching process parameters such as reaction temperature, reagent concentration, reaction time, coal-liquid ratio and agitator speed have been optimized for the flotation tailings sample from a captive washery of Tata Steel. The results obtained show that 67% demineralization could be achieved in a single stage of leaching process with a product yield of more than 65%. For further demineralization, multistage leaching was carried out and the results showed that 75-85% demineralization could be achieved with significant reduction in alumina to silica ratio. Additionally, the phosphorus content is also significantly reduced from 0.20 % to 0.022 %. Further, it is interesting to note that there is no increment of sodium content in the product coal after chemical treatment."

Jan 1, 2014

By W. L. Zeigler

THE Galena mill of the Callahan Zinc-Lead Co. is of 150 tons daily [ ] capacity and is situated at Lake Gulch, 2 miles west of Wallace, Idaho. (Fig. 1. It was constructed during the summer of 1926, work having been started late in June and the plant placed in operation Oct. 15, following.

Jan 1, 1928

By W. L. Zeigler

The Galena mill of the Callahan Zinc-Lead Co. is of 150 tons daily capacity and is situated at Lake Gulch, 2 miles west of Wallace, Idaho. (Fig. 1. It was constructed during the summer of 1926, work having been started late in June and the plant placed in operation Oct. 15, following.

Jan 1, 1928

By L. Sun

Recently, micro-tubular solid oxide fuel cells (SOFCs) have attracted the attention of many researchers because of their numerous advantages over larger tubular and planar SOFCs. These include excellent thermal shock properties giving rapid startup/shutdown capability, a high volumetric power density compared to larger tubular SOFCs, and reduced sealing problem compared to planar SOFCs. In order to screen cathode materials for micro-tubular SOFCs, the perovskite cathodes were deposited, using a variety of methods, on 10.5 mol % yttria-stabilized zirconia (YSZ) tubes. Their electrochemical properties were then evaluated by using electrochemical impedance spectroscopy and steady-state polarization methods, based on a three electrode configuration, and with the reference electrode position carefully optimized. The oxygen reduction reaction kinetics at the cathode/electrolyte half cell were then investigated in detail.

Jan 1, 2005

By Pierre R. Hines

The first progress in American ore dressing practice was made in the mills of the Mother Lode in Calif., the Comstock Lode in Nev., and Gilpin County in Colo., during the years 1861 to 1870, when the ancient wooden stamp battery, with square wooden stems, was converted into the 'California' stamp made of wrought and cast iron, with round stems which rotated. Eli Whitney Blake invented the jaw crusher in 1858 for stone crushing, and it was soon used for crushing ore. F. W. Gates' gyratory crusher followed twenty years later. S. R. Krom, Thomas A. Edison, and others improved the Cornish rolls by increasing their size and spring pressures; the Symons Brothers made horizontal and vertical disc crushers; W. Ball and E. T. Leavitt designed powerful steam stamps for Lake Superior native copper ores; and jigs were mechanized. William B. Frue, a mill superintendent in the Lake Superior copper district, invented the vanner in 1874. Arthur F. Wilfley built his riffled concentrating table in 1895, just after Dr. Robert H. Richards commenced his Ore Dressing. The Wilfley table so changed concentrator flow sheets that Dr. Richards was compelled to revise his text, and its publication was delayed until 1903. The value of sizing or classifying before concentration was recognized. Dr. Richards had persuaded the Anaconda Copper Mining Co. to install round tables with special surfaces to catch the 'extremely fine free mineral.'l Gravity concentration had achieved almost every refinement for recovering or separating minerals by the difference in their specific gravities. However, one serious problem remained unsolved, i.e., how to retrieve the enormous loss of the extremely fine mineral in the slime portion of the ore. Slime, then, as now, was not a precise term due to the variation in the mineral composition of the ores and the different requirements in crushing, grinding, sizing, and classifying. At that time, slime was considered to be fine sand and colloidal material passing 100 mesh.2 Most sulfide ore minerals are more friable than their associated gangue minerals, so that crushing and grinding increased the proportion of the extremely fine ore minerals in the slime. Sparkling specks of galena, chalcopyrite, argentite, or ruby silvers, according to the ore, floating away on the tailing stream from vanners and slime tables, were familiar sights in the old gravity concentrators. Gravity concentration practice was aimed at recovering the ore minerals at the coarsest possible size because the recovery was higher and unnecessary

Jan 1, 1962

By K. Hanumantha Rao, K. S. E. Forssberg

The separation of feldspars from quartz has been the subject of numerous studies since 1930 and the flotation process so far proved to be the most suitable method. In the conventional process, feldspars are separated from quartz using a cationic collector and hydrofluoric acid as an activator of feldspars. There is no general agreement on the mechanism of fluoride activation of feldspar surfaces and the role of fluoride ions is briefly discussed. The use of HF is no longer acceptable due to environmental and health problems, and a few new reagents schemes have been reported. The available evidence shows that the success of these new reagent schemes is very limited. A new reagent scheme which is environmentally safe and cost effective for the separation of feldspars from quartz is yet to be resolved.

Jan 1, 1994

By G. H. Walrod, J. M. Mutmansky, Y. J. Wang

The selection of a shaft size for ventilation purposes is a classic problem of concern to mining engineers. This presentation is concerned with the sizing of conventionally-sunk circular shafts with concrete or shotcrete linings. Costs of sinking shafts of three different depths, from 150 m to 300 m (500 ft to 1000 ft), and six different diameters, from 4.27 m to 7.32 m (14 ft to 24 ft), were obtained through questionnaires to shaft contractors. The primary objective of the economic model presented is the balancing of detailed annual capital and operating costs to achieve the minimum overall cost of the shaft installation over its life. The economic model is similar to previous analyses but treats several of the individual cost categories in an updated fashion. Included in the paper is a detailed analysis of the effects of varying power costs on optimal shaft size. Also included are a statistical analysis of current shaft costs and comments on the choice between shotcrete and concrete linings.

Jan 1, 1979

By Jan M. Mutmansky, Gordon H. Walrod, Y. J. Wang

The selection of a shaft size for ventilation purposes is a classic problem of concern to mining engineers. This presentation is concerned with the sizing of conventionally-sunk circular shafts with concrete or shotcrete linings. Costs of sinking shafts of three different depths, from 150 m to 300 m (500 ft to l000ft), and six different diameters, from 4.27 m to 7.32 m (14 ft to 24 ft), were obtained through questionnaires to shaft contractors. The primary objective of the economic model presented is the balancing of detailed annual capital and operating costs to achieve the minimum overall cost of the shaft installation over its life. The economic model is similar to previous analyses but treats several of the individual cost categories in an updated fashion. Included in the paper is a detailed analysis of the effects of varying power costs on optimal shaft size. Also included are a statistical analysis of current shaft costs and comments on the choice between shotcrete and concrete linings.

Jan 1, 1980

By Julián Ortiz C., Clayton V. Deutsch

Indicator simulation allows specification of different continuity of high and low values through the use of grade thresholds. The sequential implementation of indicator simulation has been widely used, but the problem of order relation deviations remains a significant drawback. A new procedure for "Hierarchical Indicator Simulation" is introduced that avoids order relations and offers greater flexibility than the conventional sequential approach. The new implementation simulates all locations at the largest threshold and then considers decreasing thresholds in turn. All nodes with grades that are above the previous threshold are excluded from the domain of the current threshold and therefore, they are not used as conditioning data. The probability of being above or below the threshold is calculated using simple indicator kriging using all conditioning data in the domain, thus the covariance structure is preserved. The theoretical framework of this new approach is fully developed. Practical implementation details are discussed. Application to a copper deposit shows the advantages and drawbacks of the method. Finally, the possibility of incorporating multiple-point statistics is discussed.

Jan 1, 2002

By Fernanda de Melo Fernandes

A deposição de filmes finos por plasma melhora várias propriedades físicas, químicas e biológicas de superfícies que contribuem para o enobrecimento dos materiais. O objetivo desse trabalho é estudar a cinética de deposição de filmes finos de cobre, utilizando a técnica da gaiola catódica, alterando a espessura da tampa da gaiola, e sua relação com a variação da potência do tratamento. Filmes de cobre caracteriza-se como bom condutor elétrico e térmico, o que justifica seu uso em microeletrônica, segundo a U.S. Environmental Agency (EPA) existem 282 tipos de ligas de cobre bactericidas, habilitando sua utilização em ambientes estéril. Assim, realizou-se deposições de filmes finos de cobre sobre substrato de vidro, variando a corrente do processo e a espessura da tampa da gaiola. Avaliou-se a variação de peso da amostra depositada, definindo o peso resultante das deposições. Realizou-se também a caracterização por difração de raio-X, microscopia eletrônica de varredura e análise tribológica (calotest). Os resultados mostraram que, o tratamento com espessura de tampa de 12 mm promoveu o filme mais espesso e mais contínuo dentre todos os tratamentos, com uma grande quantidade de cobre depositado, o que induz que a razão ideal diâmetro de furo/espessura da tampa é 0,67.

Oct 30, 2017

By P. Zamora

El yacimiento epitermal de alta sulfuración Au-Ag de Tantahuatay se encuentra en un campo volcánico situado en el sector nor-oeste del Distrito de Hualgayoc, región Cajamarca, norte del Perú. Desde Agosto del 2011, el yacimiento viene siendo explotado a cielo abierto por Cía. Minera Coimolache S.A constituída desde 1995 por Southern Peru como accionista del 44%, Cía. de Minas Buenaventura S.A.A del 40% y Espro SAC. del 16%. Dentro de 23,000 Has. de concesión se tiene al 31/12/2016, 1.0 Moz Au en reservas de mineral en óxidos, distribuidos en cinco depósitos, de los cuales dos son actuales tajos en operación. El LOM (Life-of-Mine) se ha trazado hasta el 2021 con una proyección hasta el 2024, si se integra 690 Koz Au de recursos y potencial actuales, como futuras reservas.

May 1, 2008