Search Documents

By Bradford C. Wesstrom

The extraction of metals from Copper Refinery Slimes may involve many different processes. This paper describes the use of pressure leaching for decopperizing of copper refinery slimes at the El Paso Refinery. Process equipment will be described, along with the process chemistry, unit operations and unit processes associated with the decopperizing process. Copper contained in the raw slimes ranges from 15-35%. After autoclaving less than 1 % copper remains.

Jan 1, 2000

By Albert Tasias, Daisy Jiménez

La gestión de riesgos mediante barreras, conocida como metodología Bow Tie, permite acompañar el día a día de las operaciones y está adquiriendo mayor relevancia debido a su forma sencilla de describir los peligros a través de un diagrama, en donde se pueden ver las causas y las consecuencias. Asimismo, lo interesante de la metodología son las barreras, que evitan que el peligro o las consecuencias se materialicen, para lo que cuentan con un responsable que debe gestionar y reportar su desempeño. Este trabajo realiza un análisis de la metodología Bow Tie, a través de un glosario de términos, la descripción del proceso, su aplicación actual y las ventajas y desventajas asociadas.

Sep 20, 2019

By J. C. Trantham, J. W. Marx

From 1955 to 1958 the Phillips Petroleum Co. conducted a series of small scale counterflow combustion field tests in a tar sand about 60-ft deep and 6 to 12-ft thick near Bellamy, Mo. A total of seven different well patterns, including conventional five-spots and seven-spots plus a 15-well line drive pattern and a 10-well radial pattern, were employed. Electric heaters, gas burners and wellbore fuel packs were tested as counterflow ignition devices. Direct drive ignition followed by reversal to counterflow operation was not possible in this case because of formation plugging by the semi-solid tar during the direct drive phase. Sustained counterflow burning was achieved with wellbore fuel packs under conirolled conditions which permitted close correlation of fire front velocity, air velocity, air-oil ratios and yields for a wide variation in process parameters. The tar in place was about 10' APl with a reservoir viscosity greater than 500,000 cp. The composite oil prodlcct was 26' API with a viscosity in the range of 5 to 15 cp. Vertical sweep efficiency in the line drive pattern was essentially 100 per cent, with no evidence of gravity segregation. Original tar in place ranged between 800 and 1,000 bbllacre-ft, specific rock permeability averaged about 800 md before burning and effective air pemeability with residual oil and water in place (at the time of ignition) averaged 250 md. The volume of oil recovered during stabilized line drive counterflow burning represented about 67 per cent of the volume of tar originally in place in the burned out zones. A minimum was found when air-oil ratios were plotted against formation air velocities, and a limiting air velocity existed below which the counterflow fire front reversed and burned back over its own trajectory, using the residual coke left behind. INTRODUCTION Early in 1955 the Phillips Petroleum Co. began preparations to field test counterflow underground combustion as a method for producing oil from high viscosity hydrocarbon deposits, such as bituminous (tar) sands. At that time all published information on the use of underground burning io increase oil recovery was based on the direct drive process, in which the fire front moved through the formatim in the same direction as the injected air stream. Such direct burning is not applicable to many heavy oil sands or to most tar sands because the heat-thinned native hydrocarbon congeals in the cold rock ahead of the fire front forming a gas permeability block which smothers the combustion. Laboratory experiments first demonstrated that this permeability blocking would not occur if the fire front and the air stream moved in opposite directions. In this counterflow (reverse) burning process the heated heavy oil or tar is driven back through the combustion zone. Here thermal cracking produces relatively light hydrocarbon products which pass through the heated rock behind the fire front (largely in the vapor phase) and are incapable of causing a gas permeability block.' Exploratory wring revealed that consolidated bituminous sandstones with a combination of tar saturation, permeability, thickness and depth favorable for experimental field testing existed at several points in western Missouri. By the fall of 1955, a test site for determining technical feasibility of the counterflow process under field conditions had been selected near Bellamy, Vernon County, Mo. — about fifty miles north of Joplin. The pay zone was too thin and too shallow to constitute a commercial prospect, but these same factors permitted controlled experimental operation with a small compressor installation and with a large number of monitor wells. These were needed for adequate observation of the underground phenomena at reasonable cost. RESERVOIR CHARACTERISTICS The reservoir chosen for the experimental field tests was a 124 thick section of tar sand extending from 49 to 61 ft subsurface, with shale and siltstone laminations sealing the top and bottom. This section was part of a larger 30-ft thick tar sand deposit which extended both above and below the test zone. Core analyses showed that the 12-ft sand was effectively subdivided into two approximately equal sections, with the lower zone being consistently more permeable than the upper zone. The most significant laboratory core data are summarized in Table 1. The line drive test which is the principal subject of this report utilized only the lower 6-ft thick zone, with the upper zone regarded as part of the 55-ft overburden. WELL PATTERNS The over-all field test program involved a total of seven different well patterns, including conventional five-spots and seven-spots plus a 15-well line drive pattern and a 10-well radial pattern. In some of the tests the full 12-ft zone was employed; in other cases only the more perme-

Jan 1, 1967

By Harry H. Power

INDUSTRY has the right to expect the petroleum engineering schools to supply more than the minimum technical qualifications necessary to obtain or discharge the responsibilities of a particular job. The basic training, social and economic orientation, should go far beyond these minimum requirements. Petroleum engineering students should also be well grounded in the history of the oil business so that they may understand the industry's progress since the advent of the Drake well. Furthermore, according to P. H. Bohart, the schools "have a definite duty to help the students form a workable philosophy of life, which includes an appreciation of the service of science to mankind, and a belief in the obligation of the individual who enters a profession to exalt himself by continuing his studies and growth so that he may never cease making contributions to the advancement of science and industry."

Jan 1, 1948

By Frank Mucciardi, Hujun Zhao, Pietro Navarra

"A heat pipe is a device having a very high effective thermal conductivity in which two-phase flow and heat transfer takes place. Recent research at McGill University has led to a new type of heat pipe that contains a flow modifier. This improvement has enabled the device to operate at the high heat fluxes encountered in the metallurgical industry.This paper summarizes the progress made to describe the fluid flow in the evaporator section of a McGill heat pipe with the goal of understanding how the flow modifier configuration is linked to the film boiling and dry-out limitations. A separated flow model, an instability analysis, a lift-off model and an energy balance model are used to calculate the theoretical CHF with varying flow modifier configurations and operation conditions. A summary of the current work to relate the flow modifier to the dry-out limitation is also given.Determining how the flow modifier affects both the film boiling and dry-out limitation will give insight into improving the flow modifier design so as to extend the operational range of McGill heat pipes in terms of maximum heat flux and heat load capabilities.IntroductionThe McGill heat pipe is a specialized two-phase heat exchanger developed for several metallurgical applications where temperatures and heat fluxes are typically close to or beyond the maximum safe range of conventional cooling technology.Over the last few years, several breakthroughs have brought this device beyond the proof-of concept stage and a series of industrial trials have been performed with success. These trials include two oxygen injection applications for the ferrous and non-ferrous industry [l], and two light metals permanent-mould casting applications [2,3]. Current projects include a blast furnace copper taphole cooling application [4], a copper smelting application and a thermal analysis probe application."

Jan 1, 2004

By E Nye and T Schroeter, B Muir, M Kitson, M Gonzalez, D Mares

The single track North Strathfield Rail Underpass (NSRU) consists of a dive structure either end of a 148 m long driven tunnel skewed under three live railway tracks. The tunnel is 8 m high, 9 m wide, with a horseshoe profile, excavated by full face using a road header. Ground cover varied between 2.5 m to 3.5 m. Settlements were 5 mm to 15 mm (the latter due to a dyke). A one pass synthetic fibre reinforced shotcrete lining was installed (no lattice girders or steel sets were used). A system of automated robotic total stations was used to provide real time monitoring of the rail track and associated ground formation. No disruption to train services occurred.CITATION:Gonzalez, M, Kitson, M, Mares, D, Muir, B, Nye, E and Schroeter, T, 2014. The North Strathfield Rail Underpass – driven tunnel design and construction, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 369–374 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By Alireza Kamrani, Yashar Pourrahimian, Hooman Askari-Nasab

In-pit crushing and conveying (IPCC) is an option to decrease the enormous operating costs that a truck shovel can introduce in an open-pit mine. Finding the best locations for the IPCC over the mine life will impose a new set of requirements for the mine planning. Through a two-step mathematical programming model alongside the road network, this method finds the optimal in-pit crusher locations and relocation times first and then optimizes the long-term mine schedule. The model is verified by a real mine. The results show that the truck travel time could be reduced by 500% and the discounted cash flow increased by 8% with an optimized schedule considering the crusher placement.

Jun 25, 2023

By G. W. Josephson

VIRTUALLY every year inventors find one or more startling new uses for one of the varied products of the nonmetallic mineral industries. For example, in November a major step toward positive control of rainfall was made when an experimenter converted a cloud to snow by dropping a few pounds of solid carbon dioxide into it. Other examples of ingenuity in the development of markets and production methods are noted in the following pages. For most of the industrial mineral products one of the outstanding features of 1946 has been the high level of production. There are exceptions, such as quartz crystal and lithium, whose production capacity during the war outgrew current peacetime needs, but they are few. Some technical men point out that this prosperity is not an unmixed blessing to technologic progress, because so much effort must go into day-to-day production problems that relatively little opportunity is left for the pursuit of new developments.

Jan 1, 1947

By S. J. van Wyk, A. S. H. Haagner

Land rehabilitation transcends the mere establishment of vegetation across disturbed landscapes; it should be conceptualised as a specialised ecological reconstruction process. This process necessitates a long-term perspective on the success of land repurposing. It requires a continuum of inputs specified and managed by a dedicated and qualified custodian to ensure the sustained economic viability and ecological sustainability of the land. Based on the authors’ combined experience and field observations over more than five decades, they advocate for an urgent shift away from traditional land rehabilitation practices toward a paradigm centred on land capability reconstruction and active stewardship. The prevailing rehabilitation culture has overly simplified the process to a mere revegetation exercise, which is fundamentally incompatible with the comprehensive requirements for sustainable land capability. While the regulatory framework provides valuable guidance for obtaining a mine’s social license to operate, a paradigm reset is essential. Mining companies must prioritise rehabilitation quality, set achievable sustainability goals, and establish clear pathways and milestones to meet relinquishment criteria. Currently, the status quo view—a model reliant on outsourced contracting and agricultural approaches—is that mine rehabilitation is a one-time intervention rather than a complex, systemic, and long-term process. This perspective presents significant challenges, as the success of ecological interventions can only be accurately assessed over extended timeframes, often spanning decades. Shortsighted rehabilitation specifications, coupled with practitioners operating within agricultural decision frameworks, frequently overlook the necessity for integrated rehabilitation expertise and the scientific foundation essential for designing and implementing effective ecological outcomes. A lack of long-term monitoring information impedes the required adaptive management of rehabilitated systems and, therefore, delays the transition towards final land use. This short approach costs the mining industry millions annually, often without recognising the inadequacies in long-term liability mitigation and the substandard ecological success achieved. The disconnect between procurement processes, the qualifications of service providers, and the unclear pathways to relinquishment can impede successful rehabilitation outcomes, frequently undermining progress toward sustainability milestones. Unless there is a fundamental reset of the land rehabilitation culture, pursuing sustainability will remain an elusive and perhaps impossible objective. Consequently, mining companies may hesitate to fully commit to sustainable land rehabilitation practices, as the prospects for relinquishment and final closure remain uncertain at best.

Apr 25, 2025

By Waldemar Dyrssen

BEFORE discussing the relation between air pre-heaters and waste-heat boilers in conjunction with the open-hearth furnace, it is necessary to have a clear idea about what a preheater can accomplish and what effect it has on the open-hearth furnace, especially from a thermal point of view. It is generally recognized now that the heating of the combustion air in the checker chambers of the open-hearth furnaces is not as efficient as it is-desirable to make it. It is also generally recognized that heating of the air in checker chambers of ordinary construction has its limitations. These limitations are mostly the .space occupied and the cost that would be involved if checker chambers were made larger than according to present practice. There are, however, other. reasons why checker chambers cannot give the highest possible air temperatures. Checker chambers are capable of heating air to very 'high temperatures by using waste gases of extremely high temperatures and, in fact, higher temperatures can be reached with checker chambers than with any other means available. The temperature to which we can heat, air, however, is limited very materially by -the temperature at which the air enters the checkers, be-cause of the fact that checker chambers, as at present constructed, are not efficient in heating air through a wide range of temperatures. In other words, if air in-stead of entering the checker chambers at atmospheric temperatures could enter at about 1000 to 1200 deg. F., the resultant air temperature at the top of the checker chambers would be materially increased. There are now on the market metallic air preheaters which are ex-tremely efficient for preheating air to about 1200 deg. F. Such heaters occupy very little space and can usually be installed at a relatively low cost.

Jan 1, 1928

By Gilmar Zacca Batista

The present work is a part of a comprehensive program that aims to evaluate the girth welding procedures for heavy wall API 5L X65 pipes produced for sour service applications. This article describes the results of toughness, strength and sour resistance of girth welds produced with different welding consumables. The methodology applied included girth welds production with GTAW process for root pass using ER70S-6 consumable and FCAW process for filling passes using E71T- 1CJ and E91T1-GM-H4 consumables. Mechanical tests of Charpy, CTOD, tensile, hardness and stress corrosion cracking were also performed. The E71T-1CJ resulted in a girth weld with tensile and yield strength around 7% lower than the pipe. However, according to the papers analyzed at this study, a value up to 10% of undermatching could be acceptable. The CTOD and Charpy tests showed good toughness and weld metal embrittlement was not observed. The hardness and the stress corrosion cracking tests demonstrated that the consumable ER70S-6 is suitable for sour service. All properties evaluated met the requirements specified by the onshore pipeline standards, showing that the consumables ER70S-6, E71T-1CJ and E91T1-GM-H4 are suitable for the welding of heavy wall X65 pipe with sour service and toughness requirements. If an overmatching is required, the E91T1-GMH4 shall be used to assure a strength overmatching and prevent plastic strain concentration at the weld metal. The results provided by this paper can be used for consumable selection and for welding procedure qualification of pipelines construction when heavy wall API 5L X65 are used for sour gas transportation.

Aug 16, 2017

By F. Shahbazian

attempt to systematize the knowledge on slag viscosities, the present work was carried out. The Among the physical properties of slags, viscosity is very important in understanding the mass out in the temperature range 1438-1762 Q The rotating cylinder method was used in the viscosity measurements. Crucibles and spindles made out of pure iron were employed. The transfer phenomena in metallurgical processes. The viscosities of fayalitic slags are of great interest in the non-ferrous metal industry, with special reference to copper production. In an slags were prefused before the measurements. In order to take into account the vaporization reactions involving CaF2, pre- and post measurement samples of the slags were chemically analysed and the compositions were ascertained. The results show that in the case of the CaO-SiO2 system, CaF2 additions tend to decrease the viscosity, in accordance with the expectations. In the case of the "FeO"-SiO2 system, at higher "FeO" / SiO2 ratios in the slags, a reverse trend was observed. The results are discussed on the basis of a viscosity model for silicate melts developed in the present laboratory as well as the structural considerations of silicates.

Jan 1, 2000

Underground mining has the potential to be one of the more dangerous industries in the United States and the world. Following recent disasters in Sago, WV; Darby, KY, and Crandall Canyon, UT, the mining industry was reminded of the need for a system to allow trapped miners awaiting rescue to survive following a disaster. To address this need, Battelle has developed a Mine Barrier Survival System (MBSS) that surpasses all current technologies and sets a new standard for keeping miners alive in the event of a fire, flood, explosion or collapse. The MBSS creates a temporary refuge for miners who cannot escape by using inflatable barriers and a post-fire atmosphere scrubbing system to define the ?safe haven? and remove CO2 and CO while replacing oxygen and providing heat. Current personal-protective systems in use are designed to provide breathing air for only a few hours when, realistically, it may take days for rescue teams to reach trapped miners. Battelle?s MBSS is designed to aid up to 15 miners for four days.

Jan 1, 2008

By A. R. House, G. W. Shepherd

Newmont USA Limited owns and operates the Phoenix Mine near Battle Mountain, Nevada, USA. The existing milling facility has operated since 2006 (House, 2010). Following the startup of the milling operation, and coupled with the upswing in the copper market, Newmont realized that Phoenix had no process option to treat transition and oxide copper ores. This meant that potentially revenue generating ore would be mined as waste. With no system in place to treat the transition and oxide copper, work began to determine the most feasible approach. After evaluating multiple options, the flow sheet was set for a runof- mine (ROM) heap leach pad and solvent extraction/ electrowinning plant (L-SX/EW). This paper will discuss the eight years of successes and challenges with developing the copper L-SX/EW plant and achieving commercial production of copper cathode.

Jan 1, 2014

By G Hancock, J Lowry, T Coulthard, W Erskine, M Saynor

An important part of planning for the rehabilitation of uranium mine sites is the ability to assess the geomorphic stability of the final landform, over time frames ranging from decades to millenia. Depending on the environmental conditions, erosion features such as gullies may incise into containment structures, potentially leading to the exposure and transport of encapsulated radioactive material. Further, erosion may lead to increased sediment loads and the transport of other mine-related contaminants off-site and into downstream waterways. While erosion may be monitored and assessed over the short term (years to decades), the longer-term behaviour (centuries to millennia) of such landscapes is not within any meaningful human management time frame. Landscape evolution models (LEMs) can provide information on soil erosion rates at decadal or centennial scales over large spatial scales, and evaluate the sensitivity of these processes to environmental changes. However, an important issue associated with the use of models is the ability to assess the reliability and accuracy of the model. In this paper, the CAESAR-Lisflood LEM is tested for its ability to predict soil erosion from a series of 30 m × 30 m experimental plots specifically constructed for this purpose on a trial rehabilitated landform at the Ranger Uranium Mine in the Northern Territory, Australia. Model predictions of bedload and suspended sediment loads from the erosion plots were compared with field measured observations collected over four wet seasons from the trial landform. Once calibrated for the specific site hydrological conditions, the predicted sediment yield – specifically, bedload – demonstrated an excellent correspondence with the field data. However, longer-term simulations of ten years identified an exhaustion effect in sediment yield from the landform. These latter results indicate that a weathering function needs to be incorporated into CAESAR-Lisflood to ensure confidence that the CAESAR-Lisflood LEM will be able to correctly predict the long-term evolution of a rehabilitated landform once it has been?constructed.CITATION:Lowry, J,?Saynor, M,?Erskine, W, Coulthard, T and Hancock, G, 2014. A multi-year assessment of landform evolution model predictions for a trial rehabilitated landform, in Proceedings Life-of-Mine 2014 , pp 67–80 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

By D. Vanin

"Conventional single heading track drifting in the hard rock mining industry has not shown any significant improvements in advance rates, despite the advent of modern track jumbos and igh speed muck handling systems .This paper presents Kiena 's experience in using a 7 ft 2 in. diameter larva Mark 6 Tunnel-Boring Machine (TBM) for driving 6000ft of drift.IntroductionKiena Gold Mines is located about 5 miles west of the town of Val d'Or, Quebec, approximately 300 miles north of Montreal. The mine commenced production in October 1981 and has gone through various expansions of ore production with 287 916 metric tonnes in 1982 to reach 453 800 metric tonnes in 1986.Due to the majority of claims being covered by a lake, a grassroots exploration drive of remote areas of the property was required to allow diamond drilling on a yearly basis. High speed sequential excavation methods (SEM) of single heading drifting in the mining industry has not progressed much in the past 20 years despite the advent of electric-hydraulic jumbos, Haggloader and Hagglund type cars. Certain examples of record SEM drifting advances have been performed in the past but only under very specific ground and cost conditions."

Jan 1, 1987

By W. Dresler

Design details of a 100 kVA DC electric-arc reduction furnace are described. The furnace is equipped with a 610 mm (24 inch) diameter graphite crucible hearth. A 76 mm (3 inch) diameter top graphite electrode is used as a cathode. The current passes through the bottom of the crucible and is carried to a bottom plate (the anode) by conductive magnesia carbon bricks. The furnace can be operated up to a maximum of 120 V, 1800 A, and presently 100 kW. The start-up operating experiences and metallurgical results of one reduction test with a Montana chromite containing 38% Cr2O3 are discussed.

Jan 1, 1994

By D. M. Muir

Many plants produce iron(II)/(III) waste liquors which must be treated by neutralisation and precipitation to remove the iron. Iron can be precipitated as crystalline goethite or jarosite by controlled oxidation at low pH and as magnetite by controlled oxidation at high pH, but only at elevated temperatures (>70°C). This study focuses on the characterisation and settling properties of the iron oxides produced at ambient temperatures using various neutralising agents in order to improve the performance of thickeners. It was found that two-stage addition of caustic to FeC12 solutions produced a fast settling material characterised by Mossbauer spectroscopy and XRD as maghemite and magnetite. However, lime and magnesia additions resulted in more ferrihydrite formation and much lower settling rates because of the enhanced oxidation of Fe(II) by air. Settling rates decreased significantly as the proportion of Fe(III) to Fe(II) in the liquor increased. The mechanism of iron oxide precipitation is discussed together with some reasons for the different behaviour of the neutralising agents.

Jan 1, 2006

By T. Nyakudarika

The Unki Platinum Mines concentrator, employing an MF2 circuit configuration which includes fully-autogenous primary milling of run-of-mine (ROM) ore, was commissioned in November 2010. The project was Anglo American Platinum?s first PGM concentrator in Zimbabwe and would form a significant contribution to the group?s platinum production. The project financials demonstrated that the project was operating-cost sensitive. After reviewing the metallurgical testwork, mineralogical examinations, and the history of similar operations, it became apparent that the Unki ore characteristics rendered it amenable to autogenous milling. The primary ball mill, structurally designed for 30 per cent steel load, could be operated at the required initial phase throughput with fully-autogenous primary milling, realizing savings in both power requirements and grinding media consumption. The original mill sizing had been done with fully-autogenous milling in mind, but allowing for flexibility and mitigation in case of varied mining fragmentation. Since attaining steady state, target grinds have been achieved. This paper looks at the Unki ore characterization programme, design considerations, and the operational and control philosophy for a successful comminution circuit, and discusses the design to produce a flexible, low opex, mitigated comminution and overall MF2 flowsheet that is easily expanded in line with the potential for optimum exploitation of the orebody.

Jan 1, 2012

By R. W. Diamond

Introduction THE Sullivan mine and the milling, smelting, and refining operations of the Consolidated Mining and Smelting Company are sufficiently well known to make unnecessary anything more than a very brief account of the events which led up to this Company's branching out into the chemical industry. This development is the result of the 26 per cent sulphur content of the Sullivan ore. Seventy-five to eighty per cent of this sulphur enters the mill tailing, which is stocked at Kimberley. The remainder, contained in the lead and zinc concentrate, is burned off in the first treatments at Trail. Prior to this new development, the sulphur gas was wasted to the atmosphere. In spire of its great dilution with air and discharge from stacks at high elevations above the plant, some damage to vegetation close to the plant was experienced. It had always been apparent that this sulphur should be recovered and utilized if possible, at the same rime relieving, or curing, the smoke nuisance, and constant studies with this in view had, therefore, been maintained. One of the early conclusions reached was that the Canadian prairies would ultimately require large quantities of phosphate fertilizers, as had been the experience of older countries, and that these fertilizers would constitute a large outlet for sulphuric acid which could be made from smelter gases. This conclusion prompted a widespread search for phosphate rock, particularly in British Columbia and western Alberta, with the result that low-grade beds were discovered in the Crowsnest district and to the north therefrom through extensive areas (1). Following these discoveries, an experimental plant was built at Trail for the production of triple superphosphate in order to facilitate field-tests in fertilizing prairie lands.

Jan 1, 1934