Search Documents

By J. Donald Rimstidt, Jeanette K. Jerz

Acid mine drainage is a major environmental problem worldwide. A key to remediating this problem is understanding the rate and mechanisms of the complex, multistep pyrite oxidation reaction under geologically relevant conditions. Because many waste piles are not submerged, a large amount of pyrite oxidation actually occurs in air. We have designed a Barcroft-manometer reactor to measure the rate of pyrite oxidation in air as a function of relative humidity and oxygen partial pressure. The reactor consists of two chambers joined by a manometer. Each experiment occurs at constant temperature, initial oxygen partial pressure, and relative humidity, although these variable can be changed between runs. Oxygen consumption was measured and pyrite oxidation rates were calculated from those data. Initial data indicate that rate of pyrite oxidation by oxygen in humid air is much faster than the rate of oxidation by oxygen in solution. The rates determined by this study can be used to develop better remediation techniques for acidic mine waters.

Jan 1, 2000

By D. E. Parson, W. A. Morgan

This paper offers a brief review of current literature pertaining to vacuum degassing or vacuum casting of steel as practiced in the U.S.A., Germany and the U.S.S.R. The advantages of vacuum degassing of large forging ingots, heavy section casting, for the conversion of rimming bessemer steels to killed steel and for the production of transformer steels are discussed. Operating pressures, reduction in gas contents and improvements in hydrogen segregation, steel cleanliness and mechanical properties, obtained with the various techniques, are described. The paper includes a description of an experimental vacuum stream-droplet degassing unit and some preliminary results obtained at the Physical Metallurgy Division Research Laboratories Department of Mines and Technical Surveys, Ottawa on laboratory steel melts. Experimental 500 lb direct arc, basic melts have been spray cast into either ingot moulds or dry sand moulds, held inside a vacuum tank. Also 500 lb melts have been

Jan 1, 1961

By J Mercuri, S Dunford, P Rothman, E Bartsch, J Snyder, D Newton, R Maron, D Cirulis

The purpose of a mineral comminution circuit with a ball mill running in closed-loop with a hydrocyclone classification cluster is to feed the downstream process with the target particle size. Maintaining the optimal particle size in the flotation feed can significantly improve plant cash flow. In particular, reducing the amount of coarse material is often a major challenge. Existing instrumentation to provide particle size measurement is considered standard equipment in most modern concentrator plants. However, availability is often very low, mainly owing to high maintenance requirements of the analyser and associated sampling system.CiDRA Minerals Processing has developed two novel and robust technologies that address this challenge by providing high reliability and very low maintenance systems for on-line measurement of coarse material in the overflow of individual hydrocyclones. The first system is non-invasive and measures pebbles and rocks greater than 6 mm. This paper focuses on the second system, which is a ruggedized wetted sensor design with no moving parts and provides a real-time trend of the desired target grind size parameter, such as percentage above 150 micron.Both systems have simple robust designs and measure in the primary overflow stream of the individual hydrocyclone. Individual hydrocyclone measurement enables identification of poor performing hydrocyclones in addition to providing a representative measurement of the whole hydrocyclone cluster. The systems do not require sampling and associated sample transfer piping circuits that are prone to plugging, thus avoiding high maintenance requirements.The wetted sensor will be described in detail along with its implementation in a robust control scheme in a major copper concentrator in North America. Plant data shows very high availability, achieved with very low maintenance, has enabled improved process control, thereby maintaining throughput and ball mill target power while reducing grind size.CITATION:Cirulis, D, Dunford, S, Snyder, J, Bartsch, E, Rothman, P, Maron, R, Newton, D, O’Keefe, C and Mercuri, J, 2015. Process optimisation using real-time tracking of coarse material in individual cyclone overflow streams, in Proceedings MetPlant 2015, pp 93–109 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 7, 2015

By R. M. Lauer

OVER THE YEARS concentration of the Sullivan ore has become progressively more difficult as the ore has become increasingly refractory. The introduction of new reagents and changes in the flow of the concentrator have been and continue to be necessary in order to maintain and improve the efficiency of metal extraction. Prior to the completion of the pilot mill in 1957 ail new ideas were developed in laboratory equipment. If these were found to be promising, there was no alternative but to introduce them directly to the main mill flow in one step. When a major change was involved there was always the possibility of serious losses while the mill was being adjusted to the changed conditions. It proved difficult to determine whether these losses were the result of the changed procedure or of failure to adjust the flow to a change in the condition of the ore during the test. The pilot mill has provided a valuable intermediate step between the laboratory and the mill. It avoids the losses which occurred when unsuccessful full-scale tests were attempted, and conversely it provides assurance that full-scale flow changes can be made without serious hazard.

Jan 1, 1960

The mechanism of thiosulfate decomposition and the products formed were investigated in the presence of pyrite or pyrrhotite in copper-ammonia solutions used for leaching gold. The presence of the sulfides significantly increased the decomposition of thiosulfate. The sulfide-surface-catalyzed oxidation of thiosulfate to tetrathionate by dissolved oxygen or the cupric tetra-ammine complex was proposed to be the dominant thiosulfate decomposition mechanism. The catalysis of the sulfides in this reaction could originate from their strong affinity for aqueous sulfur species and their semiconducting properties. Oxygen was found to be the initial driving force for thiosulfate decomposition in the absence of cupric ions and the driving force for the continuous decomposition of thiosulfate in the presence of cupric ions. Under an oxygen free atmosphere, the decomposition of thiosulfate was limited to reduce the cupric ions and the catalytic effect of the sulfides was also marginal. The dominant oxidative product of thiosulfate was trithionate in alkaline solutions especially in an oxygen rich or cupric ion rich environment. Tetrathionate was found in relatively smaller amounts in an oxygen and cupric ion deficient environment. Tetrathionate was not stable and would further decompose after extended periods. Trithionate concentrations increased almost linearly with time.

Jan 1, 2005

By F. L. Bosqui

A. L. BlomFIeld, Denver, Col. (communication to the Secretary.*) — Mr. Caldecott says on p. 67: "The Dorr thickener shown, while a useful device when crushing with cyanide solution for removing surplus solution from slime pulp prior to air-lift agitation or vacuum filtration, is not adapted to effect as complete a separation of water from settled slime as the ordinary intermittent settlement and decantation." This statement might have passed muster in this country several years ago when. the Dorr thickener was a new device, but its use in hundreds of mills in the United States has demonstrated that as thick a product is being discharged from it as was obtained from the intermittent settling which it has supplanted. • It is interesting to note that recent investigation, especially the work of 11. 6. Coe and G. H. Cleveilger,' in the March Bulletin of the Institute, under the title: Laboratory Method for Determining the Capacities of Slime Settling Tanks, has developed the general theory of settlement and explains the results obtained in practice. Just as free settlement is a function of surface area, so thickening after the zone of free settlement is passed is a function of time. The time required is obtained by the capacity or volume provided in the settler for this thickening zone. Each pulp is a problem in itself, both in regard to free settlement and to time required to reach a commercially finished thickness. Some pulps require 48 hr. and more to reach a density of 40 per cent. solids; others no coarser to the screen test reach a density of 65 per cent.' solids in a fraction of that time. In thickening any pulp a point is reached where the increase in density is so slow as to be commercially unprofitable. When any part of the pulp has reached this point it should pass on for treatment—its place in the thickener should be occupied by pulp which has not yet reached the commercial limit. By doing this the whole volume of the settling tank is kept in active use. Thus the continuous thickener keeps the whole tank at work to its commercial limit, while the intermittent settler has much of its volume occupied at times by pulp which is either quite finished thickening or at least thickened past the commercial point. The mechanical efficiency of the continuous thickener can be the only argument for limiting this statement. In my own experience I have never

Jan 1, 1916

By A. U. Miller

"Ventilation is one of the meet important factors in mining, although until recent years less thought has probably been given to effective ventilation than to any other one phase of mining. In the past, very little, if any, attention was given air courses until they became so constricted by falls that the volume of air was greatly reduced; and, in addition, the stoppings and doors were so poorly constructed that only a very small percentage of air reached the face workings.As a matter of fact, mines have been visited where the volume of air being circulated in certain sections was much larger than in others, and where the management was striving to increase the flow of air in those sections with the least air current, believing the ventilation to be deficient. After sampling and analyzing the return air from the various sections in such mines it has been found that the quality of the air in certain places with the largest flow was more impure than in some of those with the least flow.In past years, practically all mine fans were operated by steam-driven engines supplied with steam from the mire boiler plant. No check was made on the steam consumption or the power cost of operating the fan, therefore the management had very little if any definite information as to cost of ventilating the mine.With the increased use of electrically-driven equipment in mines electricity is being used more and more to drive mine ventilating fans, and since in many instances the current is purchased from central power plants operators have come to realize that in many cases the cost of operating the fans is very high. Some engineers estimate that it ranges from 20 to 50 per cent of the total power cost of the mine. This information, together with the fact that mines are now being developed on a larger scale, requiring larger quantities of air for the men to dilute the gases liberated, has caused the large progressive companies to make, a more comprehensive study of mine ventilation, resulting in a decided improvement in the quality and quantity of air at the face workings, as well as reducing materially the ventilating costs."

Oct 1, 1930

By J. Bostjancic

As wastewater discharge regulations become more stringent, power plants, manufacturing plants and other industrial sites are looking for ways to reduce makeup water requirements and to recycle and reuse as much wastewater as possible. In some cases, environmental regulations require zero liquid discharge, meaning all wastewater must either be retained on site or reduced to solids for disposal off site. Zero liquid discharge or "closed-loop" wastewater treatment systems using evaporators and other process equipment have been well-accepted in recent years. Often overlooked is the fact that zero discharge is not just the latest fashion--many commercial zero liquid discharge systems have been in operation since the mid-70's. This paper will give specific examples of zero liquid discharge operations from 1974 to the present, showing how evaporation equipment and processes have changed to meet the requirements of industry and environmental regulations.

Jan 1, 1996

By Denis Tepavac, Mark Trim

Structural performance of fiber reinforced concrete (FRC) depends on its ability to carry tensile forces after cracking. Australian Standards AS5100-2017 and AS3600-2018 are the only available design standards that establish a test procedure to determine strength and toughness of an FRC in direct tension. Direct tensile testing of fiber reinforced shotcrete samples was performed to determine if the model and guidelines in AS5100/3600 were applicable to shotcrete; all previous testing was from cast samples. In addition to direct testing, micro CT-scanning was also performed. The paper presents tests performed, results, and how the tests could be used on future projects. In addition, a brief summary is provided of the guiding structural mechanics used for estimating residual tensile strength and test methods utilized to verify those estimates.

Jun 13, 2023

By T. Kerr, C. Mattich, J. Wilson

"In refractory gold concentrates, gold is occluded in sulphide minerals preventing efficient cyanide leaching. Hence, roasting is used to oxidize sulphur and organic carbon, the latter being necessary to minimize recovery loss through the preg-robbing effect. In 2009, Outotec commissioned the circulating fluidized bed roaster at Syama gold mine in Mali. Since 2013 Resolute and Outotec have been implementing improvements to the roaster performance with the capacity increasing from 8000 t/month in 2013 to above 13,000 t/month in 2016, while achieving a residual sulphide sulphur and organic carbon contents of below 0.1 wt.% and 0.4 wt.%, respectively. Thus a gold recovery in the CIL of above 90% is attained. In 2016, Outotec audited the Syama roaster. The analysis resulted in the Low Carbon Roaster (LCR) upgrade concept which (i) allows re-processing of calcine dust from the spray cooler and ESP after pelletization and (ii) allows the roasting of a further fine-organic carbon rich feed, i.e. de-slime circuit tailings. The LCR upgrade aims to reduce organic carbon to <0.2 wt.% and increase roaster-leaching gold recovery by >3%. Project development included extensive testwork. The LCR process is expected to become operational during FY 2019.INTRODUCTION Double refractory sulphide ores exhibit the characteristics of gold locked within pyrite grains, in the presence of preg-robbing natural (organic) carbon. Hence, to achieve high recovery during subsequent processing steps, i.e. cyanide leaching, oxidation of sulphide sulphur is required, producing a porous calcine by way of a roasting step. This allows for the gold contained within the pyrite grains to be accessible during cyanide leaching. Furthermore, it is necessary to oxidize the organic carbon. Oxidizing the organic carbon is essential as gold recovery loss occurs as a result of gold-cyanide complexes being adsorbed on organic carbon, this phenomenon is termed as preg-robbing (Miller et al., 2016). The gold absorbed on the organic carbon is lost, reporting to the tailings stream. Hence, the aforementioned oxidation of sulphide sulphur and organic carbon is the process goal. Nonetheless, the latter must occur at a controlled temperature which is concentrate/ ore specific, since the pores of the produced calcine should not sinter, as this makes the gold contained in the calcine less accessible during leaching, leading to gold recovery loss. The tight temperature control requirement is a decisive factor in the choice of a Circulating Fluidized Bed (CFB) as the roasting reactor, due to the excellent mixing characteristics of the CFB which results in temperature homogeneity of (+/-10°C). Roasting of double refractory ores, as described above, can be included in the flowsheet after comminution and grinding, a process termed as whole ore roasting, or by including a flotation circuit termed as concentrate roasting. Roasting the flotation concentrate results in less solid flow, increased sulphide sulphur grade and organic carbon content resulting in a higher heating value and higher gold content. A typical composition of the Syama ore and concentrate is given in Table 1. Ore average values presented correspond to the period 2015, while concentrate values are typical for the flotation performance throughout the period 2012–2015."

Jan 1, 2017

By B. W. Steele

"Dofasco began operations in 1912 as a steel foundry located in Hamilton, Ontario. Today, Dofasco is a fully integrated mill that manufactures hot rolled, cold rolled, galvanized and tinplate steels. Customers include the automotive, construction, tubular, manufacturing, appliance, packaging and steel ser-vice centre industries. Raw steel production and purchased semi-finished steel processed in1994 was 3.5 million net tonnes. Dofasco employs 7300 people at its Hamilton facility.Environmental management at Dofasco is guided by its environment policy and associated commitments. This paper discusses Dofasco’s responsibility for its products as it relates to these commitments. Dofasco is com-mitted to:n the principles of sustainable development that require that activities be conducted in a manner that provides for the present without compromising the ability of future generations to meet their needs. These principles will be integrated into product design, manufacturing and business planning;n managing renewable and non-renewable resources through the responsible application of reduce, reuse, and recycle principles;n minimizing any potential impact of its operations and products on the environment, employees, customers and the community;n continuous improvement of the effectiveness and integrity of our environmental management systems;n developing understanding among all employees about their responsibilities, and assigning the necessary authority; andn meeting the standards set by relevant legislation and international agreements through participation with governments and the diligent application of economically feasible and scientifically sound methods and technologies."

Jan 1, 1996

By John J. Henn

An evaluation is presented of the Bureau of Mines process for the recovery of metal and mineral values from municipal incinerator residues. This process employs standard mineral beneficiation techniques and is operating on a pilot-plant scale of 1,000 pounds of incinerator residue feed per hour. Products from this separation process include ferrous, aluminum, and copper-zinc scrap, and colorless and colored glass. Cost estimates were prepared for four plant sizes. The estimated capital and operating costs For the four plants follow: [ ] It is assumed that the separation plant is located adjacent to a municipal incinerator. Provision is made, however, for part of the residue feed to be delivered by truck so that one large separation plant can be used for residue from more than one incinerator.

Jan 1, 1971

By G. Upadhya

Considerable success has been achieved recently in modeling microstructural evolution during solidification of castings bthrough the coupling of macroscopic heat transfer with microscopic solidification kinetics models. However, a complete model for simulation of solidification in complex shaped castings involves: (i) the description of fluid flow, during and after mold filling, coupled with (ii) heat transfer to the mold and surroundings by use of a macro model, followed by (iii) a description of subsequent solidification of liquid metal by use of a micro model for solidification of the alloy under consideration. This paper describes the coupling of solidification kinetics model to a 3D, transient, fully coupled fluid flow and heat transfer model. Coupling between the macremicro models is achieved by using the latent heat method. Micro models for the eutectics of gray, white and ductile iron are discussed. This coupled code has been used for predicting the thermal history and microstructural data for shaped castings. Various applications of the model, including prediction of shrinkage defects, grain density contours, and graylwhite transition region in the casting, are presented for a relatively complex casting geometry.

Jan 1, 1992

By J. E. De Waele, J. J. Lee, M. J. Mulheron, Luke R. Deamer

There is increasing demand for geotechnical contractors to commit to carbon reduction, net zero or science based targets. A lot of focus has therefore been placed on using low carbon materials and low emission rigs. However, whilst these are ways to help reduce carbon, there is a need to look beyond just substituting materials and fuels to meet net zero. Using the IEMA carbon hierarchy, there is a need to first look at eliminating and reducing emissions, before considering substitute materials. For example, in geotechnical designs, this may mean considering using ground improvement or reducing the number of piles, before considering using low carbon cements. Equally, for remaining emissions, this hierarchy means considering carbon negative products to offset emissions, such as ground source heat pumps. This hierarchy can also be applied throughout geotechnical contractor organisations. For example, considering video conferencing for meetings, before considering public transport or using an electric vehicle. This article explores the carbon hierarchy and how it can be applied to all areas of a geotechnical contractor’s business. Only through embedding this hierarchy across the business can geotechnical contractors achieve the step change required to meet net zero.

May 1, 2022

By Wei Sun, Jaewon Choung, Zhenghe Xu, Zhangming Cui

"High intensity conditioning has been demonstrated in a number of cases to enhance fine particle flotation. The improvement could be attributed to the enhanced formation of particle aggregates. However, the understanding of aggregation mechanisms remains rather limited. Recently, an enhanced particle aggregation was observed by the formation of small air bubbles resulting from high intensity agitations (HIA). In this study, a novel visualization system is designed and constructed for characterizing the fine bubbles formed in an HIA cell. The new design allows determination of gas evolution and bubble size distribution. With this system, the effect of dissolved air on fine bubble generation by HIA is investigated. The results show that HIA creates a favorable environment for the formation of gas nuclei and small size bubbles due to hydrodynamic cavitation.INTRODUCTIONFlotation is a dominant separation technique employed by mineral industry to recover the valuable mineral particles. However, in general, particles finer than approximately 10 µm are not effectively recovered by conventional froth flotation technique due to their low inertia and high specific surface area (Fuerstenau, 1988). Therefore, the fine particle flotation has been considered as the central challenge of flotation research. Substantial advances have been made for fine particle flotation from both a theoretical and technological point of view (Fuerstenau et al., 1979; Song and Lu, 1990; Subrahmanyam and Forssberg, 1990; Sivamohan, 1990; Sedat and Barry, 1991; Matis, 1995). High intensity agitation (HIA), for example, has found some success to improve fine particle flotation kinetics in laboratory tests (Chen et al., 1999a and 1999b; Valderrama and Rubio, 1998; Rubio and De Brum, 1994).The effect of mechanical agitation on flotation kinetics has been recognized for many years. In mid-1970s, Warren (1975) reported that increasing the shear rate of the pulp could improve the efficiency of ultra fine particle flotation. He attributed this improvement in flotation to the formation of aggregates. This concept of aggregation has been extended by Rubio (1978), and Bulatovic and Salter (1989), who employed high intensity agitation (HIA) method to promote aggregation. They found that HIA with the addition of collectors, frothers and suitable modifiers significantly improved both the flotation recovery and selectivity of ultra fine sulphide minerals. The improvement was explained by warren’s shear flocculation theory. Till now, many studies (Chen et al., 1999a and 1999b; Valderrama and Rubio, 1998) have been undertaken to improve fine particle flotation by HIA. However, most of these studies were focused on the relation between energy input and flotation efficiency. Less information was available for describing how the aggregate formed during HIA process."

Jan 1, 2006

By Nadia C. Miller

In situ stope leaching is an innovative mining system that reduces the surface impacts of conventional underground mining. As in any leaching operation, stope leaching requires hydrologic site characterization and control of leaching solutions. Several tracer tests, using sodium chloride (NaCl) in various concentrations, were conducted by the U.S. Bureau of Mines (USBM) in an underground experimental stope to simulate a leaching environment. The tests were conducted in fractured crystalline rock that was partially water-saturated. As tests progressed, the surrounding fractures became more saturated. A predominant flow direction away from the stope was found during testing. Testing procedures, results, and a remediation plan for in situ leaching based on field observations are presented in this report.

Jan 1, 2010

By Harry R. Nicholls

As part of the pre- and post - shot mine examination at Project GNOME , acceleration data were recorded underground from a series of chemical explosive shots . The cube root of the charge weight was used to scale acceleration and distance because charge weight was not constant . Regression analysis of particle acceleration - distance data gave the following propagation equation : A W1 /3 = 5.10 x 105 ( R / W¹ / 3 ) −2 .43 The quantity A W1 /3 is scaled particle acceleration expressed in g's - lbs¹ / 3 , and R/W1 /3 is scaled distance expressed in ft / lbs¹ /3 Data obtained from the nuclear explosion were scaled and fall within one standard deviation of the calculated propagation law for the smaller shots . Cube root scaling laws were adequate to group acceleration data from explosive charges varying by a factor of more than 1 x 10 in charge weight and over shot - to - gage distances varying from 100 to 46,000 feet . Data obtained from a series of small tests provided sufficient data from which reliable predictions of acceleration could be made for the large nuclear explosion .

Jan 1, 1964

By R. R. Sayers

Carbon monoxide poisoning is one of the most widely distributed and most frequent causes of industrial accidents . Carbon monoxide gas is a product of incomplete combustion , and since it is without color , odor , or taste , its presence is frequently unsuspected in many places where it exists . It is an ever present danger about blast and coke furnaces , smelters , and foundries . It may be found in buildings having a leaky furnace or chimney , and in buildings where a gas stove is used without a proper flue connection , such as is often found in tenements , tailor shops , and boarding houses . Hospitals receive annually a great number of victims of poisoning , either by accident or in an attempt at suicide , from artificial illuminating gas . People may be affected by leaks wherever water gas is formed or used . The exhaust gases from gasoline motors under average running conditions usually contain 5 to 7 per cent carbon monoxide , and sometimes as much as 13 per cent ; deaths from running an automobile engine in a closed garage are not infrequent . A similar danger may arise in operating gasoline engines in launches without sufficient ventilation . The gas is formed also in stoker rooms , in gun turrets on battleships , in petroleum refineries , and by the Lablanc soda process in cement and brick plants . In underground mines carbon monoxide may appear as the result of shot firing , mine explosions , or mine fires , and in tunnels where automobiles , coal or oil - burning locomotives are operated . In spite of the common occurrence of carbon monoxide poisoning there appears to be no uniformly recognized treatment for a person overcome by carbon monoxide . In the rescue work of the United States Bureau of Mines , however , a method has been developed which has been supported by laboratory investigation , and has proved successful in practical experience , over a period of years . As outlined in this article , the method is useful in the hands of first -aid men as well as physicians .

Dec 1, 1921

By Alejandro Yañez, Martta Nousiainen, Rodrigo Grau

"Gas dispersion plays a fundamental role in froth flotation. Gas dispersion in flotation is quantified by using four properties: gas velocity, bubble size, gas hold-up and bubble surface area flux. Gas dispersion measurements were conducted in three flotation cells: TankCell 1, TankCell e300 and TankCell e500. The measurements reported in this paper were carried out exclusively in two-phase systems using only water and air at frother dosages exceeding the Critical Coalescence Concentration (CCC) in order to prevent bubbles from coalescing. The measurements conducted in TankCell 1 and TankCell e500 were conducted by Outotec specialists, whereas the characterization of TankCell e300 had been conducted earlier in 2008 by a team from McGill University. When working in two-phase systems and under non-coalescing conditions, gas dispersion characteristics measured in different scales can be compared directly. The measurements conducted in TankCell e300 are taken as a base line in order to compare the performance of TankCell e500, whereas TankCell 1 is a pilot-scale flotation cell which is used in rotor testing. The gas dispersion properties in TankCells were found to be affected by the air flow rate and rotor tip speed. Bubble sizes (d32) measured on the three-size scale seem to be within the same range of 0.6 mm to 1.6 mm. It was noted that the bubble size was influenced by rotor tip speed and gas velocity. In general, as the rotor tip speed increased, the bubble size decreased and as the gas velocity increased, so did the bubble size. The rotor tip speed also has an impact on the hold-up; in general, as the rotor tip speed increased the gas hold-up also increased but the influence of air flow rate on gas hold-up was greater. Bubble surface area flux was found to vary between 40 and 85 1/s. As the gas velocity increased, the bubble surface area flux also increased."

Jan 1, 2014

By Seth C. Schaefer

The Bureau of Mines investigated the standard Gibbs energies of forma-tion AGfo, for NiCr204 (nickel chromite) and CoCr204 (cobalt chromite). High temperature galvanic cells employing stabilized ZrOz (zirconia) as the solid electrolyte were used to measure the open-circuit potentials for the cell reactions ?

Jan 1, 1986