Search Documents

By Márcia Maria da Silva Monteiro Pereira

Durante o lingotamento contínuo de aço, partículas de ZrO2 adicionadas na escória de molde facilitam a nucleação heterogênea de cristais devido à sua limitada solubilidade. A adição de ZrO2 promove a cristalização da fase cuspidina, o que auxilia na redução da transferência horizontal de calor no molde, amenizando desta forma o problema das trincas longitudinais. Outro benefício da adição de ZrO2 em pós fluxantes é reduzir a taxa de desgaste da válvula submersa (SEN) na interface metal/escória; a erosão da SEN é um problema sério. Através de testes de laboratório e de testes industriais concluiu-se que a adição de ZrO2 em pós fluxantes reduz a taxa de transferência de calor horizontal no molde durante o lingotamento contínuo de aço, considerando os dois tipos de pós fluxantes que foram analisados no presente trabalho. Além disso, observou-se que a adição de ZrO2 reduz a taxa de desgaste da válvula submersa na interface metal/escória.

Aug 16, 2017

By Robert Hopler

THE work that is being done by the Government to reduce the dangers of mining was brought out strikingly in the First National Mine-Safety Demonstration which occurred at Pittsburgh, Pa., on October 30th and 31st, under the auspices of the United States Bureau of Mines with the assistance of the American National Red Cross Society and the Pittsburgh Coal Operators’ Association.

Jan 1, 2012

Mr. Tays (communication to the Secretary): Mr. Wynne's criticism of my paper* brings forward a few points which are really important, and might properly have been considered in the original paper. By calling attention to them he has rendered me a service. It is quite true, as Mr. Wynne says, that, in the tests reported by me, the Bryan mill was always working at a relative disadvantage, and my comparison of the work of this mill with that of the stamp-battery should be interpreted, therefore, so much the more favorably to the mill. Of course, wire screens can be used to advantage on the Bryan mill, if they are not of smaller size than 30-mesh; but

Jan 1, 1902

By Qingguo Xue, Jingsong Wang, Yingli Liu, Guang Wang

In the dropping zone of blast furnace (BF), primary slag absorbing ash of pulverized coal and coke become to be intermediate slag. Due to viscosity and surface tension of slag and the pore between cokes, some slag remained in coke layer and affected the permeability of blast furnace. The flow behavior of slag with different basicity (0.55–1.10) and Al/Si (0.35–0.50) were studied. Meanwhile, the viscosity and surface tension of slag were calculated. The results showed that, with the increasing basicity of slag, surface tension increased and viscosity decreased. With the Al/Si increase, surface tension and viscosity increased. The smallest pore that all slag can pass through was 4.5 mm. However, the height between slag droplets and the bottom of crucible indicated that the ability of slag to pass through pore were weakened with the increasing basicity and Al/Si. Thus, slag which absorbed ash from fuel become difficult to pass through coke layer.

Mar 1, 2017

By Monica C. Pinto, Gustavo H. Nalon, José C. L. Ribeiro, Rita de C. S. S. Alvarenga, Leonardo G. Pedroti, Lucas A. F. Fioresi

This study aims to evaluate the influence of mortar’s mechanical properties on the behavior of clay masonry. Experimental studies were performed using prisms of clay blocks under axial compression. The clay units were produced with a clay from Tres Rios, Rio de Janeiro, Brazil and had compressive strength of 4.9 MPa. Two mortar compositions were used, which had compressive strength of 94.7 and 50.4% of the clay blocks’ net area compressive strength. It was noticed a slight increase on the prism’s compressive strength with the increase of the mortars’ compressive strength and stiffness. Prisms made with flexible mortars had a ductile failure and collapsed under lower compressive stresses, while prisms made with stiff mortars resisted higher compressive stresses, but had a brittle failure ,crushing the blocks. A very strong mortar is not recommended. Using more flexibl mortars does not compromise the strength and stiffness of the masonry and prevents an excessively brittle failure of the structure.

Mar 1, 2017

By U. Lauwers

The influence of different waste materials in sinter blends on the quality and mineralogical composition of a sinter is described. As a result of partial preservation of the original textures of waste materials in the final product the degree of assimilation of the original material in the sinter product can be ascertained. Recycling of waste materials such as dolo char , arc-furnace slag, scrap fmes, mill scale and BOF-mud via the sintering process a saving on costs of raw materials such as flux and fuels, and a reduction on pollution can be achieved. A comparison of a typical sinter with a sinter produced through the utilization of waste materials showed a distinct correlation between certain types of waste material and some metallurgical properties. Dolochar in a sinter blend acts as part of the fuel and flux that are normally added to a sinter mix. Generally dolochar improves the quality of the sinter and decreases the consumption of coke. Other waste materials adversely influence the quality of the sinter. The glass and calcium ferrite content of a sinter when dolochar is used in the blend is similar to that of a sinter produced with only coke as a fuel in the sinter mix. The glass content is lower and the calcium ferrite content is higher, in a sinter produced from dolo char in the blend compared to a sinter produced with additions of other waste materials. Changes in the mineralogical composition are related directly to the metallurgical properties of the sinter product.

Jan 1, 1991

By R. Marandi

The effective removal of heavy metals from aqueous wastes is among the most important issues for many industrialized countries, How ever biosorption, i.e. the uptake of heavy metals by non- living biomass, has gained increased credibility during recent years. Biosorption of Cr(VI) from aqueous solution, on pretreated and immobilized Aspergillus niger was investigated in a batch and countinuous reactors. A.niger biomass pretreated by boiling in 0.5 N NaOH solution for 15 min, exhibited higher Cr(VI) removal capacity than autoclaved biomass. The optimum adsorption pH value observed for Cr(VI) ions was 2. The Cr(VI)removal rate increased with a decrease in pH. The influence of contact time, pH, Cr(VI) concentration, biomass concentration and temperature on Cr(VI) removal were also evaluated. Biosorption of Cr(VI) on pretreated biomass followed the Freundlich and Langmuir adsorption models.In this study A.niger biomass was immobilized in Na-alginate matrix. The biomass beads packed in a column were able to remove metal ions.In this study we used two different flow rate in a column, 1.5 mL/min and 3 mL/min.The breakthrough data obtained for Cr(VI) was adequately by the Thomas and Yan models and the adsorption capacity of the biomass was found to less than the adsorption capacity obtaind in the batch study. When the beads containing biomass become saturated with metal ions, the adsorbed metals were eluted using 0.5 N NaOH solution. Therefor nearly 90% of Cr(VI) was desorbed by NaOH solution.

Jan 1, 2014

In this paper, the recovery of copper minerals and molybdenite in the rougher/scavenger banks of two separate mineral processing plants is compared with recovery in laboratory (batch) cells. A number of metallurgical surveys were conducted in two plants treating porphyry copper and molyb-denum ore. Batch flotation tests were performed on plant conditioned flotation feed slurry, in parallel with the plant metallurgical surveys. The effect of flotation feed density on recovery of copper minerals and molybdenite in the plant and batch laboratory cells was investigated. Changes in flotation pulp density had little effect on copper mineral recovery, in both plant and laboratory cells. The ultimate recovery for molybdenite, on the contrary, increased considerably when the pulp density was reduced, both at plant and laboratory scale. Recovery of copper minerals in the plant and laboratory cells was comparable, while molybdenite recovery in laboratory flotation cells was 3%~13% higher than in plant. It is hypothesised that the flotation rate of molybdenite is sensitive to cell hydrodynamic conditions (i.e. local turbulent energy dissipation) more than the flotation rate of copper. The flotation behaviour of molybdenite particles is likely to be predominantly controlled by bubble-particle collision frequency, which is enhanced in high local turbulent energy dissipation environment. For chalcopyrite, the flotation recovery is mostly determined by attachment and stability efficiencies. An increase in local turbulent energy dissipation, while increasing collision efficiency, may negatively impact on attachment and stability efficiencies. The outcomes may have a considerable impact on increasing molybdenite recovery from porphyry ores.

Jan 1, 2014

By Shigeru Sarata

A wheel loader is one of the main loading machines in open pit mines. The authors have been conducting research and development on autonomous operation of loading by a wheel loader. The most common loading method by a wheel loader is the ?V shape? path method. The loading operation consists of cycles of scooping from the pile, traveling to the dump truck, loading on the dump truck and return traveling to the scooping point for the next cycle. The traveling path includes a switchback in the middle of the path. The moving direction of the loader is changed at the switchback point. From observation of V shape path loading operations by experienced human operators, it seems that they control the bucket position between the scooping point and loading point on a shorter path for higher productivity. A new path planning method is proposed this paper, whereby a point on the center of the tip of the bucket is controlled moving from the initial point and the final point. The motion of the controlled point is generated by the wheel steering the wheel loader. The controlled point is moved along the direction to the final point; however, the motion and mechanism of wheel loader have restrictions, such as the velocity of the loader, the steering angle, and the steering angular velocity. Because of these restrictions, the path of the controlled point is not a straight line between the initial and final points. When this control method is applied between the scooping and the dumping points directly, the planned path is not stable in the leaving wing of V shape path. Therefore, the initial position of the wheel loader is set at the switchback point, then two approach wings to the scooping and the dumping points are made. The whole planned path is obtained by connecting the two paths. The shape of the planned path is strongly affected by the position of the switchback point, as well as the scooping and the dumping points. By simulation of path planning at different switchback points with the combination of the scooping and the dumping points, the paths for more effective loading are determined. The results of the simulation are presented in the paper.

Aug 1, 2013

By G. R. Giuliani

Hanna Mining Company's Groveland Mine is located in the Upper Peninsula of Michigan. The low grade iron ore deposit consists of a mixture of magnetite and hematite with chert, jasper, quartz and various iron silicates (1). The ore is beneficiated by magnetic separation and anionic flotation of the iron minerals with chemical depression of the silica. The magnetic concentrate makes up about 75% of the concentrate. The concentrate is pelletized at the rate of 2.0 million LTPY of pellet production. The concentrator facilities were started up in 1959 and the concentrate was marketed as sinter feed until 1963 when the concentrator was expanded and the pelletizing plant was added. The pellet plant now consists of regrinding, elutriation, filtering, balling and induration. The pellet machine is a straight grate which employs updraft drying and cooling and downdraft drying, preheat and firing. It is necessary to regrind the concentrate before pelletizing. The con-centrate is 60% passing 325 mesh, with a surface area of ±lOOO cm2/Gm, and must be ground to about 83% passing 325 mesh, 1600 cm2/Gm blaine surface area, for pelletizing. The energy for regrind has been reduced from 12.5 KW per LT to 8.80 KW ate of 2.0 million per LT. This was the result of changes made in the concentrator where originally a coarse spiral concentrate, instead of the magnetic concentrate which is screened on fine screens to reduce the coarse fraction and prevent overgrinding before flotation, was produced. Also in 1968 an additional concentrating line was added to the concentrator which employs more grinding power than the other three lines. The demand for a high iron grade and lower silica pellet resulted in the investigation of different schemes of upgrading the reground concentrate which had more iron values liberated during grinding for surface area. The reagentized material presented many problems, mainly in selectivity trying to flot the iron and with high reagent consumption having to dereagentize the concentrate for amine silica flotation, in the various flotation systems tried. Tests were then conducted with elutriation (2) which proved satisfactory by removing the lower specific gravity, fine gangue material from the heavier material with the

Jan 1, 1977

By T. H. Ueng, S. D. Thompson, Y. J. Wang

"INTRODUCTION There is considerable interest among mining companies and government agencies in finding new ways to better control the generation and dispersion of respirable coal dust. Mine face ventilation generally has been considered the most effective tool for lowering the concentrations of respirable dust. Unfortunately, only a limited amount of research has been undertaken to determine the relationships between the various face ventilation parameters and the dust dispersion patterns. If these relationships are better understood, more efficient ways of controlling dust generation and dispersion may be evident. A practical and economical way to gain more in-depth understanding of these relationships is through scale model studies. Past research (1, 2, 3) has substantiated that scale models can be successfully used in studying ventilation parameters provided that geometric, kinematic, and dynamic similitues are maintained.To better understand face ventilation and dust dispersion, a 1/5 scale model of a room and pillar mine face was constructed. This model was then used to conduct experimental investigation on two ventilation parameters. The parameters which were examined included the line brattice distance from the face and the air quantity. The values of these parameters were varied in numerous experiments so that their effects on dust dispersion could be measured.The experiments of this study were unique in two ways. First, two different substances were used to simulate the respirable coal dust. Experiments were conducted with a tracer gas (methane) serving as the dust simulation substance. They were then repeated with an actual dust (Arizona Road Dust) replacing methane as the dust simulating substance. In previous scale model studies, the dust simulation substance has been limited to a tracer gas such as methane. The validity of using a tracer gas to simulate dust is not clearly known yet. The other unique thing about these experiments was the number of points measured for methane (or dust) concentration. Twenty five points in a grid arrangement were measured during each experiment of this study. The number of points measured for concentration in other studies has generally been very small (often 2 to 4). It is difficult to obtain an accurate assessment of how the ventilation parameters are effecting dust dispersion when only 2 to 4 points are measured."

Mar 1, 1989

By R McDonough

DTL2 contract C916 was awarded in March 2009 for S$340 M. This contract includes two mass rapid transit (MRT) 1100?m long bored tunnels using two slurry tunnel boring machines (TBMs), with an internal diameter of 5.8?m, two cross passages and 135?m of cut-and-cover tunnels The contract also includes the design and construction of a new underground station including station entrances, subway links, architectural finishes and external landscaping. The station, located at Upper Bukit Timah Road near Jalan Jurong Kechil will also double as a civil defence shelter.The works included significant traffic management in a dense urban area in order to create the working areas whilst keeping the requisite number of traffic lanes. This involved numerous utility diversions and included the removal of a 33-year-old pedestrian overhead bridge (POB) over busy Bukit Timah Road. The station and tunnelling works were completed on time, including a ‘dock and dismantle’ TBM retrieval and subsequent breakthrough of the separating wall.This paper will detail the methods and solutions used to construct the tunnels and stations, with a focus on the requirements for construction of the station to be a civil defence shelter if required. This involved solutions to tying reinforcement and placing concrete to high standards in a restricted space, as well as the incorporation of heavy blast doors and other associated protective measures. The efforts of the management team resulted in the project being awarded first prize in the 2011 Land Transport Authority’s Annual Safety Award Convention and being named winner of the Safety and Health Award Recognition for Projects (SHARP) award at the 2011 Workplace Safety and Health (WSH) Awards. As well, McConnell Dowell won a Green and Gracious Builder Award (Excellent Category) from the Building and Construction Authority (BCA).CITATION:McDonough, R, 2014. Design and construction contract C916 Beauty World Station and Tunnels, Singapore, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 411–418 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By Oliver Bowles

The use of fire as a source of heat was the first step from primitive existence toward modern civilization, and heat has performed functions of inestimable importance throughout the ensuing ages. The first commercial steam engine invented in 1698 demonstrated that heat was an important source of power, and heat has since become the motivating force for railroad trains and steamboats as well as for machines in multitudes of factories. Aside from its function of supplying power, heat is an agent of vast importance in chemical reactions and engineering processes. Because of the high temperature of steam under pressure, losses by radiation from boilers and pipes become excessive unless the radiating surfaces are covered with insulating materials. Insulation is important also for hot-water pipes and many other types of equipment from which heat may radiate. Radiation losses from heated surfaces increase rapidly

Jan 1, 1943

LOCAL COMMITTEE OF ARRANGEMENTS. Major J. W. Powell, Chairman; F. P. Dewey. Secretary; S. F. Emmons, A. S. Hewitt, J. P- Hilgard, Charles Knap, and F. W. Taylor. THE opening session was held in the hall of the new National Museum, on Tuesday evening, February 21st. President Metcalf introduced General W. T. Sherman, one of the Regents of the Smithsonian Institution, who read the following address: ADDRESS OF GENERAL SHERMAN. MR. PRESIDENT AND GENTLEMEN : I have been invited to meet you here this evening to extend to you the cordial greeting of the regents of the Smithsonian Institution, and to assure you that they are most happy to have it in their power to place at your disposal this beautiful hall, dedicated to science and art. This National Museum is the property of the United States, of which the regents of the Smithsonian are simply the custodians, and the board has delegated to its secretary, Professor Baird, the right to extend its use to the National Academy of Sciences and like kindred societies, among which we are glad to class the Institute of Mining Engineers. It is eminently fit that you should meet here at this, the nation's capital, under a roof partly your own, devoted to natural sciences, and in the shadow of the Smithsonian, founded for the exclusive purpose of collecting and diffusing knowledge among men. Of all the workers employed on earth no single class seem to me more worthy the respect of their fellows than those who seek beneath the surface for the useful minerals and metals which contribute so largely to the wealth and comfort of mankind. In no branch of human industry does intelligence come so immediately in contact with labor. To the mining engineer chemistry, mineralogy, and geology are as reading, writing, and arithmetic to the merchant;

Jan 1, 1882

By G. W. Birge

Carbonizing properties of the principal coal beds of Perry County, Ky., are described in this Bureau of Mines report. Seven samples, representing the Hindman, Flag, Haddix, and Fire Clay beds, were carbonized by the Bureau of Mines-American Gas Association (BM-AGA) method, and yields of products and physical properties of cokes were determined. Carbonizing properties of blends of Flag and Fire Clay coals, with 20 and 30 percent Pocahontas No. 3 low-volatile coal from McDowell County, W. Va., also were determined. Expanding properties of the Flag and Fire Clay coals and their blends were determined in the Bureau of Mines sole-heated oven. The Perry County coals tested are high-volatile A bituminous in rank and, with the exception of the Hindman-bed sample, which contained excessive sulfur, were chemically suitable for metallurgical use. The three coals tested in the sole-heated oven contracted less than normal for Appalachian coals of similar rank, Blending the Fire Clay and Flag coals with 20 or 30 percent low-volatile coal increased coke strength appreciably but increased the expansion beyond normal limits for industrial blends.

Jan 1, 1962

By A. E. J. Gallagher

This report summarizes the results of flotation studies conducted by the Federal Bureau of Mines on samples of extremely fine-grained lead-zinc sulfide ores. Samples from five ore deposits in the Pine Creek area, Coeur d'Alene district, Idaho, and one deposit in the Metaline district, Washington, were studied at the Albany Metallurgy Research Center to determine the recovery of sulfide lead and zinc by flotation. During the investigation it was found that flotation could be effectively applied to the selective recovery of exceedingly fine-grained lead and zinc sulfide minerals. Separation of galena and sphalerite was obtained on pulps ground through 1,600-mesh, in which most of the particles were smaller than 5 microns. Selectivity and recovery of minerals in this fine size range were enhanced by use of a chemical dye, diphenylthiocarbazone, as a galena promoter. Although unsuccessful on one ore, application of the dye in treatment of two other very fine-grained ores yielded lead concentrates containing over 62 percent Pb at recoveries in excess of 85 percent. More than 55 percent of the lead in these concentrates occurred as particles smaller than 2 microns.

Jan 1, 1961

By D. G. Skinner, J. H. Griffiths, F. T. Williams, A. G. Withers

"The absence of homogeneity, in dust-clouds underground indicates the use of a method in which the volume of air sampled is an appreciable proportion of the total volume under consideration. Of the available methods, only the impinger and gravimetric techniques seem to comply with this requirement. In practice, greater efficiency of collection of the smaller particles is possible by the use of a gravimetric filter than with the impinger. For this reason if, as seems desirable, a standard method of sampling be sought, the adoption of a gravimetric technique is to be recommended.Provided that the amount of dust collected is reasonably large, the paper filter would seem to be preferable to the solid crystal type of filter on account of its greater convenience in use.Alternative methods of sampling are desirable to cover the wide range of practical conditions."

Jan 1, 1947

By D. C. Sharpstone

THE Polaris-Taku mine is a new gold property, situated in the far north-west corner of British Columbia. Production was started in November, 1937, at the rate of 150 tons a day, and recently has been increased to 200 tons. The property, which promises to become one of British Columbia's important gold mines, was developed and brought into production in twenty-nine months after work was started on it as a virtual prospect in June, 1935, by Edward C. Congdon and associates. Inaccessibility, extraordinarily complicated geological problems, and difficult metallurgy retarded development of the property before acquisition by the present interests, an::l, in fact, discouraged two companies that had spent substantial sums upon it from continuing development. This paper is concerned with reviewing the development of the property and describing the principal features of the geology, the mining and metallurgical practices, and the equipment employed. Acknowledgments The writer is indebted to Mr. Edward C. Congdon, President of the Polaris-Taku Mining Company, and to various members of the mine staff for their assistance in assembling the data for this paper. Special thanks are due to Mr. George G. Griswold, Jr., of Butte, Montana, who generously and painstakingly prepared the section dealing with milling and power. Microscopic studies of ores were made by Professors Frank Grout an::l G. M. Schwartz, of the University of Minnesota, and by Mr. Griswold.

Jan 1, 1938

By M I. Roberts

As Australia’s mining industry painfully retrenches, mining executives and managers strive to remain viable by seeking significant productivity increases directly through process improvement and indirectly by improving leadership and workplace culture, the most powerful determinant of productivity. Culture is the combination of people’s attitudes and behaviour, together with leadership values and focus.Comprehensive new and automated data collection and management systems promise much for improving productivity, yet despite rapid advances in measurement and sharing of data, the use of data can reduce productivity unless behavioural aspects are considered and designed as part of implementation. This is because systems drive behaviour that in turn shapes attitudes to determine culture.Experience from many mine sites and other industries in three countries confirm that the most powerful drivers of people’s behaviour are the Measurement-Analysis-Reporting system and business leadership.This paper discusses fundamentals of practical, statistically valid process measurement, analysis and reporting systems before discussing associated leadership considerations for sustained improvement in safety, productivity, employee retention, leadership, accountability and commercial returns.The key to productivity improvement is improving core processes and important support processes. In turn, the key to process improvement is identifying the major process components and their interaction by measuring and then analysing their variation and level of performance. Understanding variation is often neglected yet is usually highly significant. It is essential that the fundamentals of statistically valid yet practical process and data analysis are understood and incorporated into system design to ensure productive, informed behaviour.The design and use of Measurement-Analysis-Reporting systems influences behaviour most profoundly and determines people’s effectiveness. Behavioural aspects are detailed by focusing on six primary drivers of human behaviour and five basic systems for managing businesses. These are integrated in a seven-step process and productivity improvement methodology that combines statistical, analytical, systems and behavioural factors.The paper includes development, implementation and tracking of a project plan for improving management and leadership systems to drive aligned behaviours. This key leadership responsibility is essential for improving performance to get the most from capital while providing people with the opportunity to develop greater autonomy, which is essential for self-discipline, responsibility, initiative and accountability.CITATION:Roberts, M I, 2015. Integrating measurement, systems and leadership to build safe, productive cultures, in Proceedings Third International Future Mining Conference, pp 73–82 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 4, 2015

By T. R. Ellis

Regulation of mineral property valuation methodology by governments and others is due to frauds, condemnation and takings, banking industry problems, and litigation. Definitions of "reserves," "resources," and "qualified person" continue to evolve, along with guidelines to the data and disclosure required to support valuations. A less recognized but vital issue relates to the regulatory acceptability of alternatives to the comparable sales method. Comparable sales generally work well for surface real estate, and sometimes for precious metal deposits, but not at all for most industrial mineral properties. Alternative methods, such as net present value, or a geoscience rating system, often provide better valuations. Yet US regulations dictate comparable sales as the preferred method. The task of convincing regulators of the inapplicability of comparable sales to mineral properties, particularly those lacking reserves, may be as important as the valuation itself.

Jan 1, 1999