Search Documents

By Lyle F. Smith

With the demand for larger diameter raises under all ground conditions and the increasing price of drill rods and operating costs, it was evident that there was a need for a raise borer with a variable-speed drive and fast-response torque limiting control. The raise boring machine described in this paper was developed after several years of market research and discussions with mine operators and construction contractors. This paper discusses the Ingersoll-Rand raise borers with the solid-state controlled DC motor drives. These machines have gained wide acceptance in the five-year period since being placed in operation and are designed to accommodate the range of raise diameters and lengths most required today.

Jan 1, 1978

he leaching behavior of palladium in ammoniacal solutions has been investigated by using the rotating disk technique in an autoclave. The study included the effect of rotating speed, temperature, oxygen pressure, composition of ammoniacal solutions, and catalyst on the overall leaching rate. The dissolution of palladium in ammoniacal solutions was discussed in view of the thermodynamics and a kinetic model. Even though the potential-pH diagram suggests that palladium metal can dissolve in ammoniacal solutions at room temperature, it was found that the dissolution was too slow at temperatures below 100°C but was significantly improved at higher temperatures. It was also found that the rotating speed of palladium disk had no effect on the leaching rate. The apparent activation energy was found to be 69.7 kJ/mole. Based on the results obtained, it is concluded that the dissolution of palladium is controlled by chemical reaction.

Jan 1, 1997

By William R. Kohl, Craig B. Clemmens

"Since 2010, North Central Resources, Bridgeport, WV, has been using the sonic log to estimate the rockmechanics properties of the coal and adjacent strata in their exploration drilling program. In 68 out of the 85 boreholes they have drilled since 2010, they have conducted shear wave analysis on sonic logs run in these boreholes. By incorporating the rock mechanics logs into the geological model of the coal seam, the engineers can develop a better understanding of the support requirements for the mine.WellCAD Borehole processing software provides vastly improved efficiency in analyzing shear waves from borehole sonic data than previously available methods. The calculation of most rock mechanics parameters requires knowledge of the density and both the compressional wave velocity and the shear wave velocity. Density logs are well known and an industry standard. Sonic logging is equally well known, although less frequently used, as an accurate source of compressional wave velocity. Shear wave velocity is difficult to measure in a geophysical log, but can be estimated from digitally recorded wave form records. This is a time consuming manual procedure which requires the visual examination of thousands of individual wave forms.WellCAD allows the viewing all the wave forms on a VDL display. The observer can create a pair of false logs by manually tracing the interference points on the display for each receiver. He can check himself by observing wave forms in the traditional format. He can then create a shear wave transit time log or “Delta-S” log by subtracting the false log from the near receiver from that of the far receiver. This can be plugged into standard formulae to generate curves for most standard rock mechanic parameters, including bulk modulus, shear modulus, Young’s modulus, and Poisson’s ratio.While these parameters do not entirely substitute for destructive testing, they are extremely cost effective. An entire borehole can be analyzed for the cost of a single destructive test. This allows for a more judicious use of destructive testing while permitting the extension of test data into the rock mass with much greater confidence."

Jan 1, 2015

With significant increase in steel output in the world the price of iron ores has been soaring recently. Especially, there is a strong demand for iron ores in China, leading to more attentions paid to developing low grade iron ores. In this paper mineralogy of nm-of-mine hematite ore was deter-mined, and coal-based direct reduction-magnetic concentration was successfully developed to beneficiate low grade hematite ore. Mineralogy analysis indicates that this hematite ore is a super fine refractory ore, with the main valuable mineral hematite being closely associated with quartz and distributing uniformly and mostly occurring within the size of 3~5J.lITI,leading to being difficult to beneficiate due to super fine hematite and only grading 28.83% Fetotal. This hematite ore failed to be effectively upgraded by traditional processes in trial tests, such as reverse flotation, gravity concentration, and magnetic separation, or the integration of the above processes. In contrast with adoption of the coal-based direct reduction-magnetic separation process, concentrate was produced with high iron grade and metallization degree in the present work, which provides a theoretical basis for utilization of low grade iron ores. By optimization of direct reduction conditions, such as reduction temperatures, duration and mass ratio of reductant coal to iron ore, the reduced ore with 93.72% metallization degree was prepared, and then three-stage grinding-magnetic separation of the reduced ore were conducted, the final concentrate was manufactured, assaying 69.54% Fetotal and 98.01 % metallization degree, and with low content of impurities. This iron concentrate with high metallization degree produced by this process is a superior burden for converter instead of blast furnace. This process is enviromnent friendly by directly making iron using coal and iron ores instead of coke, resulting in less emissions and low production cost.

Jan 1, 2014

By H. Sevim

Placement of coal combustion byproducts into abandoned sections of underground coal mines for the purpose of subsidence mitigation has been investigated in Illinois. Several handling and transportation systems have been examined. Prototype pneumatic and hydraulic placement systems have been developed and demonstrated. The demonstration site, Peabody No. 10 mine in Pawnee Illinois, is selected as a case study. It is found that, for a project of 5 years, transporting 150,000 tons of byproduct annually from a power plant located 32 km (20 miles) to the mine would cost $1.80 per ton and placement into underground would cost $3.07 per ton.

Jan 1, 1998

By Jeffrey Loeb

Recent trends in blasting engineering and its related fields, at the level of professional academia, have tended to exclude detailed discussion and examination of the formative experiences of the engineering student. In particular, the extra-curricular aspects of the undergraduate program in engineering—focused, in this case, on the summer job—will be shown to contain a wealth of heretofore underappreciated knowledge in the field. In Surveying the Damage: Post Traumatic Stress and Pre-Blast Surveys, I intend to outline and examine some of the more unusual experiences afforded me by my work as a preblast surveyor in the summer of 2007. In this capacity, I was required to make a visual note of existing conditions of surrounding residential and commercial structures within 100 m (328 ft) of two separate blasting sites in central-east Ontario. In the interest of both convenience and specificity, I have attempted to organize the paper as a crossdiscipline survey of the field according to the conference’s list of suggested topics. In the paper’s first section, I will discuss the topic of Environmental Improvement and Remediation by using a case study in which not one, but two dead cats were found during the course of a routine pre-blast survey. The second section will undertake a discussion of on-site blaster gossip as an entry point into a wider discussion of Workplace Communications Management. In the paper’s final section, I will detail an early morning encounter with a 300 lb, stark-naked trailer park inhabitant as a cross-sectional analysis of the topics of Drilling in Hostile Environments, Vibration and Seismology (Sizemology?), Ethics in Blasting, Crisis Management, Risk Assessment and Public Relations. It is my hope that this paper will begin to open up a critical space for discussion of the formative experiences of engineering students during the undergraduate university program in terms of their far-reaching effects on later performance within the industry.

Jan 1, 2009

By O. N. Mohanty, S. Mohan Rao, N. D. Rao, T. Mukherjee, P. V. T. Rao

"Tata Steel has its captive chromite resources at Sukinda, Orissa. They contain two ore types, i.e. (i) Ferruginous and (ii) Siliceous. The generation of off-grade ores is an increasing trend and simultaneously customer quality requirements are becoming ever more stringent. The ferruginous type ore also contains a considerable quantity of in-situ fines (~20% particles below 0.5 mm) that compound the beneficiation problem.In this paper, new strategies are discussed for producing additional value.added products after evaluating the present beneficiation practice in terms of changing market scenario, processing capability of the plant and ore characteristic. They would entail use of MGS - an enhanced gravity separator, for recovering additional products from plant tailings; production of ferruginous coarse concentrates (-3+0.5 mm with ~46% Cr2O3) using jigs; production of marketable grade lumpy (-40+10 mm size) concentrates from low grade siliceous ore using jigs and >2.8 Cr/Fe ratio siliceous ore fines treated in the Chrome Ore Beneficiation plant gravity circuit units and low intensity magnetic separator. The studies indicate that it is possible to recover 79-80% of the chromite, against a theoretical maximum of 82% from both the ore types, in the form of several marketable grade concentrates that would also include refractory grade."

Jan 1, 2003

By Alyse Munro Hindley

The increasing negative public opinion toward blasting has led to stricter regulations and increased costs. This paper outlines alternative methods of rock excavation and the safety regulations and certification required by blasting professionals. Most importantly, however, it showcases the benefits and accomplishments that controlled blasting bring to society, giving the public a better understanding of the necessity of blasting in modern society.

Jan 1, 2015

By Deventer Johanna van

Ore bodies around the world are declining in grade, whilst increasing in complexity. The level of impurities relative to the valuable metal is steadily increasing, posing new challenges to existing operations. Ion exchange is widely used in the hydrometallurgical industry for both primary recovery of metals and the removal of impurities. The superior selectivity of ion exchange resins makes them exceptionally suitable for the removal of target impurities to very low levels, thereby saving operating costs, increasing the value of the final product and significantly improving revenue. The ion exchange process in these applications is very simple, using standard ion exchange equipment and acid regeneration. The process can be fully automated, requiring minimal operator interference and supervision Examples of impurities that are successfully removed via ion exchange include iron, antimony and bismuth from copper electrolyte. In the copper electrolysis process, antimony, bismuth and arsenic tend to form slimes which are dispersed in the electrolyte. These slimes contaminate the cathode and/or decrease the quality of the copper deposition. A special chelating resin was developed to remove antimony and bismuth, while at the same time ensuring minimal chloride leakage to the sulphate matrix. The work is described in more detail in this paper. Ion exchange is also used to remove copper, zinc and nickel from cobalt electrolyte. This paper addresses a few of these examples in more detail.

By C. B. Queja

Flexible synthetic membrane liners have become a standard facet to copper and gold heap leach pad design. While gold heap leach operations have utilized most types of synthetic liners, copper leach operations have commonly only been lined with polyethylene. The objective of this study was to determine if there are any chemical reasons why other synthetic membrane types could not be used to line a copper heap leach facility. With engineered consideration, the flexible membrane liner under the ore pile serves two purposes. The first provides a near impermeable boundary which aides greatly in the collection of the metal laden process solution. The second advantage to the flexible membrane is the almost non-permeable barrier to benefit increased environmental awareness that has led to an increase in solution containment technology. The Environmental Protection Agency (EPA) has developed a compatibility test for solutions and membrane liners. The EPA Method 9090 is intended for use in determining the chemical effects of a solution on the physical properties of the flexible membrane liner material intended to contain them. Data from these tests would assist in deciding whether a given liner material is acceptable for the intended application.

Jan 1, 1995

By V. Bonilla-Sierra, M. Elmouttie, L. Scholtès, F. V. Donzé

In the presence of joint sets sub-parallel to a slope face, the stability of the rock mass is controlled by the shear strength of the joints. On one hand, if the joints are persistent their shear strength can be assessed according to Mohr-Coulomb criterion, assuming appropriate values for the cohesion and the friction angle on the joint surface. On the other hand, if the joints are non-persistent with their continuity being interrupted by the presence of rock bridges, their shear strength will increase considerably. In this latter case, the contribution of the rock bridges to the shear strength of the joint has to be accounted for in order to better assess the stability of the rock mass. A numerical analysis of the progressive failure of a rock slope involving a non-persistent joint has been set up based upon simulations performed using a Discrete Element Method (DEM) algorithm specifically enhanced for the modeling of jointed rock masses. Pre-existing discontinuities are explicitly accounted for in the model by using a modified contact logic that ensures an explicit and constitutive mechanical behavior of the joint planes. In addition, rock bridges can be spatially distributed along these joint planes following a prescribed probabilistic technique. Jennings’ formulation (Jennings, 1970) is considered as one of the first rock slope analysis that evaluates the shear resistance to sliding as a weighted combination of the shear resistance of the intact rock and the joint planes. The validity of this formulation is discussed in the present study. Contrary to the Jennings’ formulation, we show that tensile failure is an important mechanism, particularly as the dip angle of the sliding plane increases.

Jan 1, 2015

By Randy Wheeler

In recent years the issue of seismograph calibration and accuracy has been a major focal point of the ISEE Blast Vibration and Seismograph Section. In fact, questions concerning the consistency and reliability of seismograph measurements essentially led to the development of this ISEE section. One of the early actions of the section involved the development of “Field Practice Guidelines” for the use of seismographs. These guidelines specifically state that “Placement and coupling of the vibration sensor are the two most important factors to ensure accurate ground vibration recordings.” This paper will address the results obtained from using different coupling methods to record vibration and airblast levels generated from production blasting in a limestone quarry. The data obtained clearly indicate that seismometer burial provides the best coupling for recording ground vibrations. Microphone height has also been an issue regarding the accuracy of recorded airblast levels. The data we obtained indicates that microphone height is not a significant factor.

Jan 1, 2004

By John E. Miller

A high accuracy Burnett apparatus for use at 12,000 psi and 0° to 65° C has been constructed at the Bureau of Mines Helium Research Center. The apparatus is patterned after Burnett's original apparatus, but the working pressure is much higher and elastic distortion can be essentially eliminated. An operating procedure to permit faster experimental measurements is suggested.

Jan 1, 1967

By Takashi Fujii

In the OG (Osaka Gas) process which includes a fusion process of sewage disposal sludge in coke bed knowledge of molten and fluid properties of the sludge are most important to controll the process in good condition. Thus, the softening and melting temperatures and viscosity were measured by the sessile drop technique and a rotating viscometer. Obtained results are summarized as follows: Melting character of sludge slag is varied according to their composition, but closely related to CaO/SiO2 ratio in ordinary sludge and to CaO/(Cr2O3,+Al2O3+P2O5) ratio in Cr2O3 containing sludge. Fluid property of sludge slag has a correlation with optical basicity or Riboud parameter, However, the correlation is poorer than that of metallurgical slags. Especially, chromium oxide containing sludge shows high viscosity and behaves somewhat different manner from ordinary sludge.

Jan 1, 1992

By Liu Jie

Refractory iron ore deposits in China have various genesis and complicated types, the nature of which is poor, fine-disseminated and complex. Therefore, refractory iron ore could scarcely be separated and utilized by traditional mineral processing technology at present. It is necessary to explore deep reduction technology to change the characteristics of refractory iron ore and to use effectively the iron resource. And deep reduction technology is that on the condition of higher reduction temperature than that of magnetic roasting and stronger reducing atmosphere, the iron oxides from iron ore was reduced to metallic iron particle that is easy to dissociate. And then production from deep reduction is easily separated by magnetic separation and iron powder production was obtained finally. Deep reduction technology for Lingyang iron ore from Jilin, China, as the refractory iron ore, was studied in this paper. The influences of such main factors as reduction temperature, time and coal content were investigated. The results showed that the Metallization rate of reduction product was up to more than 90% under optimum conditions, and then higher iron grade and recovery of reduction iron powder were obtained from subsequent magnetic separation. Furthermore, the deep reduction mechanism in the system was studied by the means of XRD and SEM analysis for reduction production and Physical Chemistry of Metallurgy. Analytical results indicated that during deep reduction, the size of iron particle from deep reduction materials was increasing as reduction temperature rising and reduction time extending. The growth of metallic iron particle from deep reduction production was divided into such three stages as reduction nucleation, deep reduction and growth of metallic iron particle.

Sep 1, 2012

By J E. McMynn

The development of the Granduc mine presents a number of problems which are peculiar to its location and surrounding terrain. Because the development tunnels portal onto an area which is covered by an extensive glacier, and the mountain-side is subjected to dangerous snow slides, it was decided to construct an underground powerhouse to supply the necessary electric power and compressed air. This paper deals with the special problems inherent in the design and -construction of an underground plant. It involves the installation of diesel-electric generating equipment having an aggregate capacity of 1,050 kw.,and of air compressors with a total capacity of 2,400 cfm. Items dis-cussed include the selection of equipment to meet site conditions, the ventilation and cooling of the underground room, and the protection of personnel and equipment from explosions and fire. A short discussion on the automatic supervisory and alarm installation is also included. THE Granduc mine is located 135 miles north of Prince Rupert and 25 miles north of Stew-art. This seems quite accessible, mileage-wise, but, due to mountains,

Jan 1, 1963

By E. Divers

This Bureau of Mines report presents results of an underground evaluation to determine the respirable dust and gas control effectiveness of a combined (push-pull) face ventilation system for coal mines. The system utilizes both blowing and exhaust curtain, continuous miners equipped with radio remote control, and flight conveyors. Bureau of Mines tests showed a 97% reduction in respirable dust concentrations from the usual cab position on the continuous miner to the remote control operator's position. This allowed the remote control operator to be well within, and the usual cab position to exceed, Federal respirable dust standards. Tests utilizing a safe tracer gas, sulfur hexafluoride (SF6), to determine the face ventilation effectiveness of the combined blowing and exhaust system showed that the system also has excellent methane dispersion capability. Where wide entries permit, this combined face ventilation system and use of remote control can be a very effective method for dust and gas control.

Jan 1, 1982

By S. A. Bunk, E. C. Eccleston, J. J. Amsden

Fluidized bed technology has been widely applied to mineral and metallurgical processes. Over the years, modeling of fluidization technology has progressed to a level at which basic design parameters can usually be defined based on empirical correlations. In addition, scale-up considerations have become better understood, and significant advances have been made in the area of computer simulation. Despite these advances, fluidization is a complex phenomenon, and modeling tools remain limited in their ability to simultaneously model both fluidization and chemical process parameters. As a result, almost all mineral and metallurgical applications of fluidized bed technology require pilot testing prior commercial scale design. This paper outlines pilot plant testing requirements and process development considerations for development of low technical risk commercial designs.

Jan 1, 2011

By Jean Wehbe, Daniel C. Brahana

"This paper presents a case history of drilled pier construction for a new stadium in Atlanta, Georgia. The stadium structure is supported on several different foundation types, with the heaviest ""mega columns"" typically bearing on drilled pier supported mats. The project includes 141 drilled piers with design diameters of 5.5, 6 and 6.5 feet. The piers bear on bedrock at depths of 20 to 110 feet below the ground surface. Many of the piers included rock sockets with design lengths of 5 to 18 feet. A pre-production drilled pier load test program was completed including one Statnamic load test, two Osterberg Cell tests and two lateral load tests. Non-destructive testing (crosshole sonic logging and sonic integrity testing) were also performed during construction. Production pier installation with over 3800 linear feet of earth excavation and over 1350 linear feet of rock excavation was completed in a little over four months. The piers were installed using both the cased hole method and the slurry method. All cased holed required downhole inspection and slurry holes were initially inspected with a mini-SID device and subsequently by sounding. Advanced drilling equipment and tooling were used to meet the production requirements for the project. This paper reviews the highly variable soil and rock conditions encountered at the site, briefly presents the results of the load tests, and discusses pier installation procedures and the equipment used for installation. The paper also presents conclusions related to the installation and lessons learned.INTRODUCTIONWith the opening of AT&T Stadium in Dallas, a new era of stadium construction began in the U.S. The new age stadiums are larger and have more amenities than their predecessors. The new Atlanta Falcons stadium is no exception. Many of the new features, including Atlanta’s innovative retractable roof, result in extraordinary structural loads. The roof structure is supported by a series of mega columns that bear on eight large caps, six of which are drilled pier supported. Each of the pier caps contains between 8 and 16 drilled piers that bear in the underlying bedrock. The design pier diameters are 6 and 6.5 feet. Augercast piles were used to support two of the mega column caps. Drilled piers, augercast piles, aggregate piers and spread footings are used to support the more lightly loaded portions of the structure."

Jan 1, 2017

By Norimasa Yamasaki, Masao Kurosaki

"The effects of plating conditions on the crystal orientation of electrodeposited zinc were investigated by varying elecyrolyte flow rate and current density. Precipitation of the Zn (00 • 2) basal plane is promoted at lower current density and higher flow velocity. Effect of the flow velocity on the mass transport was evaluated based on the polarization measurement in which Cu was used as the tracer. As a result, it has been clarified that the crystal orientation of electrodeposited zinc can be uniquely arranged by the overvoltage (iU0.5) that can be simply calculated by considering -the current density and boundary layer thickness. At the same time, the electrode potential during electrodeposition that can be calculated by using a model based on the competitive reactions of hydrogen reduction 'and zinc reduction exhibits an extremely good correlation with the crystal orientation of electrodeposited zinc.Introduction Electrogalvanized steel sheet has better surface properties than hot-dip galvanized steel sheet, and is used in home electric appliance and automobile applications. Factors such as crystal morphology, crystal orientation and surface roughness have a large influence on its appliance, formability and corrosion resistance [1-3].Electrolysis, condition, bath composition and alloying elements are reported as factors that affect the crystal orientation of the electrogalvanized coating. Factors that can be controlled on time in the production site are electrolysis condition that-is current density and plating solution flow velocity.Some studies[4-6] report that the crystal- orientation of the Zn(00 • 2) plane is increased by promoting, the mass transfer of zinc ions in the plating solution or decreasing the concentration overvoltage, but did not investigate in detail the plating solution flow conditions in the plating cell nor quantitatively determine the effects of both current density and plating solution flow conditions on the crystal orientation of ' electrodeposited zinc."

Jan 1, 2000