Search Documents

By L. Gutierrez, R. Yepsena

Enargite in porphyry copper deposits is an important mineral as it displays good floatability under the presence of the collectors usually used in the flotation of copper sulfides. As a result, copper concentrates grades are reduced. As scarcity of water resources is a problem relevant to Chilean mining, the use of seawater is a feasible solution. The behaviour of copper sulfides and molybdenite in the process of flotation in seawater was previously studied but not for enargite. The objective of this research is to study the behaviour of the enargite in different conditions of electrochemical potential during the process of flotation using seawater. The study was carried through micro-flotation tests using pure samples of enargite, at Eh values ranging from -300 to 500 mV(SHE), both in seawater and aqueous solutions containing calcium and magnesium. The results show that at pH 10.5 in seawater, the enargite and chalcopyrite recoveries are reduced throughout the whole range of Eh studied. At pH 9 in seawater, enargite and chalcopyrite are depressed under reducing and slightly oxidising conditions. The recovery of both minerals drastically decreases at Eh values lower than -100 mV and greater than 400 mV. The behaviour of enargite in seawater flotation differs from that observed in conventional water, since in the latter case the recovery of enargite decreases at higher potentials close to 500 mV. Keywords: Enargite, flotation, seawater, redox potential

Jan 1, 2020

By J M TORLACH

Learning is an iterative process, and we might reasonably expect that after more than a century of mining during an era of sustained technological development, (following a millenium or two of unrelieved hard physical graft), that the more obvious physical hazards could by now be competently managed. It is perhaps a reflection on the perversity of human nature that we have not fully learned our lessons in this exacting environment, and that worse, we have still too often failed to profit by the experience of those lessons. The more obvious underlying factors which impact on this situation are examined briefly, as a prelude to consideration of some outstanding examples of recurrent problems experienced in recent years. Reasons for the continued existence of sub-standard practices are outlined, with a focus on the human element, and finally proposals for appropriate remedial strategies are summarised. This paper therefore seeks to examine and discuss some of our deficiences and to suggest some directions for the way ahead.

Jan 1, 1992

By S. Partney

Waste clay ponds are a necessary part of the phosphate rock beneficiation process. They are large, averaging a square mile in size; unsightly, in that they protrude 20 to 50 feet (6 -15 meters) above natural grade; stabilization and reclamation is slow; and they have had a history of catastrophic failure. The State of Florida has never published a specific rule regarding the configuration or height of these ponds, but has enforced numerous policies along these lines. The current rules are given and interpreted, along with the reasoning for current policy. In addition, an overview of the history of the policies, and an attempt at explaining the reasons for the changes that have occurred is given. The industry has been forced to make major monetary decisions, having effect for decades on mine economics, in a constantly changing regulatory environment. The Bureau of Mine Reclamation is confident that a direction of regulation has been solidified, but changes are still to be anticipated.

Jan 1, 1998

By S N SHEARD

The use of geophysics in mineral exploration in Australia, and overseas, has increased dramatically over this century. This paper shows that using simple equipment with clever interpretation that the foundations of modem geophysics were laid, using all the same principles. The plethora and diversity of mineral exploration geophysical techniques does not allow a full description of their evolution to be given in such a paper. To convey this evolution, however, the progress of two different geophysical methods, magnetics - a potential field (passive) method, and electromagnetics - an electrical (active) method, are described. Examples of magnetic survey data from the 1920s and more recent vehicle home and airborne surveys are given to show the increase in data quality through technological improvement. A set of four airborne electromagnetic data sets spanning three decades is used to indicate the improvement in electromagnetic techniques. It is argued, that considerable progress is still required in the electromagnetic field to increase its interpretability.

Jan 1, 1992

By L. Martins Demuner, D. Burzic, V. Cunha Aranda, F. L. Lourenço, G. Romeu Trindade dos Santos, F. Ramstorfer

For many years, Dynamic Soft Reduction has been regarded as a proper method in improving internal quality of slabs. Even though processes models improved significantly over the past years, the efficiency of Soft Reduction was always limited by the discretization error, which inherently exists if segment rollers cannot be positioned individually. The recently developed SRD segment type allows for an individual roller positioning within the mushy zone by avoiding any discretization deviation from the optimal gap. This paper provides a detailed technological overview of the SRD segments as well as operational results at their very first implementation at Ternium Brazil.

Oct 1, 2019

By Kyle Amoroso, Aaron K. McCain

Frozen soil shoring has been used for decades in the tunneling industry to provide temporary support of excavation for shafts and cross-passage excavations. However, horizontal penetrations through the frozen soil can prove to be challenging. The key to creating a stable portal through frozen ground is managing and mitigating groundwater flow into the excavation through the annular space surrounding the drill stem or casing. This paper will review different approaches that have been successfully used to penetrate frozen soil shoring on multiple projects.

Jun 13, 2023

By Luis Fernandez-Deza, James Hawn, Dustin Mount, Jean-Marc Wehrli

The RiverRenew Tunnel System project in Alexandria, VA forms part of a CSO scheme aimed at reducing overflows of combined stormwater and sewage into the Potomac River during storm events. A major piece of the project is a 12-foot internal diameter tunnel of approximately 12,000 feet length lined with a single-pass precast concrete segmental liner and excavated by an Earth-Pressure Balanced Shield TBM. The tunnel lies between 120 to 140 feet below grade in the clays of the Upper Potomac Formation with occasional dips of more granular, saturated soils of the Terrace Formation and the Alluvium. The TBM is launched from a figure-8 configuration Pumping/Screening Shaft located within AlexRenew’s operational Water Resource Recovery Facility. This paper discusses the challenges encountered during the launch of the TBM in short mode within a highly congested site and from narrow deep shafts.

Jun 13, 2023

By Yuan Le, Dominic Reda, Vojtech Ernst Gall, Kurt Zeidler, Tomasz Kecerski

High Speed 2 (HS2) mandated that Building Information Modelling (BIM) processes be implemented during design and construction. Gall Zeidler Consultants (GZ) was responsible for developing the BIM Models for the portals, tunnels, and cross passages of the of the 16 km-long Chiltern twin-bore Tunnel. In addition, GZ developed the GBR for the Chiltern Tunnels and incorporated the relevant information into the Project’s BIM framework. This paper presents the implemented BIM framework, describes the modelling approach, and discusses the advantages and challenges of implementing BIM, particularly how BIM improved interface coordination and how BIM was used in feasibility assessments of different construction options.

Jun 13, 2023

By T Atchison

In-pit crushing and conveying (IPCC) systems have come under growing scrutiny as a perceived mitigation to fuel and equipment price fluctuations, labour shortages and the need to move everincreasing volumes of material. Individual vendors and delivery organisations are now offering a sometimes confusing array of systems, particularly for the dig and dump side operations.One system does not suit all operations. This paper seeks to document the factors that should be considered in assessing the suitability of different IPCC systems, with a focus on dig side equipment layouts in particular. These factors include the productivity of the systems, interactions with the drill/blast and bench operation sequence, the ease of relocation, flexibility to changes in the reserve, scalability and compatibility with other elements of the system.

Jul 11, 2011

By K. Adham

Both the dry and the wet fluorination systems require hydrogen fluoride (HF) for the process of uranium conversion to uranium hexafluoride (UF6). The dry methods depend on the electrolysis of HF to generate the fluorine (F2) required for the high temperature pyro-fluorination. The wet methods require aqueous HF in water solutions for the low temperature hydro-fluorination (Argonne, 2019). This paper uses the available HF safety guidelines and industry information to discuss the issues of transportation, storage and utilization. Health effects and environmental considerations are reviewed. Safe practices for handling the HF (both as anhydrous and as aqueous) are considered. Proper selection of different materials of construction are discussed, for both the anhydrous and the aqueous HF.

Jan 1, 2020

By D McLaughlin

This paper points to the timely importance of commencing a centrally recognised perpetual collection of mineral specimens in the Northern Territory which has as one of its objectives the collection and preservation of Northern Territory minerals of scientific, educational and heritage value. Currently in the Northern Territory there is no government department or institution that has a resourced coordinated state-wide objective to collect and document collectable mineral specimens. Specimens held in storage by the Department of Mines and Energy and the Museum and Art Galleries of the NT are not catalogued and owe their existence to fortuitous circumstances, not as a result of a planned systematic scientific approach to mineralogy. Northern Territory mineral species and unique specimens have and will continue to be driven to extinction while no central and active, recognised repository exists. This situation persists despite the fact mineral production is the Territory's largest income earner. The paper presents the arguments that hopefully will assist decision-makers to commence development of a state mineral collection lodged within an appropriate institution in the Northern Territory.

Jan 1, 1994

By Ovchinnikov YN, Novikov VS, Spirin NA, Babushkin NM, Mysik AF, Shcherbatskii VB, Kukarkin AS

Laboratory investigations were carried out to determine the resistance coefficient of the flow through beds irrigated with wetting and non-wetting liquids. A formula was obtained which may be used to evaluate the resistance of the irrigated packing. Quantitative investigations were also carried out on operating furnaces at Magnitogorsk. Continuous measurements of the lower pressure drops were made under different furnace conditions. Pressures were measured in the tuyere space and the bosh region. A significant transient behaviour of the pressure drop was observed in the irrigated zone as a function of the accumulation of the liquid phase in the bosh region as smelting progressed. Additionally, transient processes were also investigated in the upper furnace zones. The basic cause of the transient behaviour was shown to be the irregularity of burden descent caused by the casting cycle. It was shown that the rate of burden descent between consecutive casts reflects fairly accurately the accumulation and drainage of the liquid products as a result of which heat transfer, reduction and aerodynamic processes assume transient character. In practically all cases of casting a decrease in blast pressure and that over the furnace height of 0.2 kg/cm2 was observed. The analyses of radial gas composition at the stock line showed that compositional variations connected with the casting cycle are most pronounced in the central and peripheral regions, whilst in the intermediate regions the conditions are relatively stable. Calculations show that as casting progresses there is a decrease in the gas flow rate at the periphery and an increase in the centre of the furnace. The transient nature of the aerodynamic processes in packings revealed the existence of an appreciable reserve capacity. Elimination of transience was tested on the furnace at Magnitogorsk and improved operating and economical furnace parameters obtained.

Jan 1, 1975

By S Das

Deposit-10/11A is situated in the iron rich Bailadila region of India comprising haematite ore of average grade 65 per cent Fe. The deposit production line was commissioned in the year 2002 having a capacity of 5 Mt/a. The plant has the state of the art mineral processing equipments.The ore is transported from mines to crushing plant by means of dumpers. The ore is comminuted in two stages to get 150 mm top size product and this product is transported through conveyor system and is stored in silos as feed stock for beneficiation plant. In the beneficiation plant this crushed product is wet screened in two stages to produce a product of lump (-150 + 10 mm) and fines (-10 + 3.15 mm). The product of -3.15 mm top size is fed to primary classifier for a size separation at 150 µm. The resultant product (-3.15 mm + 150 µm) is dewatered and transported to fi ne ore product stock yard through conveyor system. The minus 150 µm material from classifier overflow is fed to cyclones (508 mm cyclone battery with an apex of 65 mm) for desliming at 45 µm and to recover ultrafi nes (-150 + 45 µm). The cyclone overfl ow slimes (-45 µm) along with water is treated in lamella thickeners to recover process water. The thickener underflow material is transported to tailing pond (discharge rate is 300 m3/h at a specific gravity of 1.4) by pumping through HDPE (high density poly ethylene) pipeline and the over flow water is being recirculated. The water requirement for beneficiation is approx 1.5 m3 per ton of ore.This paper aims at identifying and quantifying the factors that affect the overall plant performance (grade and recovery) during the different seasonal variations especially in the rainy season (mid-June to end October). The effect of seasonal variations on unit operations such as milling, classification, thickening and filtration are discussed. Specific cases are presented as examples and recommendations are formulated.

Jul 11, 2011

By G Cooper

The Société Nationale Industriel et Minière (SNIM) is expanding its ore and concentrate production capacity in Mauritania, West Africa. This government-controlled mining company has been in production since 1963 and currently exports some 12 Mt/a.SNIM is presently doubling its magnetite concentrate production at the Guelb el Rhein mine. An existing processing line will have a second parallel production line of 4 Mt/a added. The mine is located some 600 km inland from the Atlantic coast in the heart of the Sahara Desert.The metallurgy of the ore is reasonably straightforward. It is a magnetite banded iron formation that is amenable to magnetic separation. While the existing plant uses semi-autogenous grinding and dry magnetic separation, the new processing line will use HPGRs, dry magnetic separation, and a wet milling and magnetic separation circuit for treating middlings.The process choices refl ect the scarcity of water in the region, the high cost of locally generated power and the operating experience and preferences of SNIM. Dust control in the desert environment has been a particular challenge.The metallurgical design aspects as well as the infl uence of the environmental and commercial aspects of the project are presented.

Jul 11, 2011

By Manca PP, Lassandro R, Caranassios A, Massacci G, Ciccu R

The paper discusses the state of the progress reached in the development of the diamond wire tool for cutting hard rocks. To the advances of this relatively new technology a substantial contribution has been provided by the research being carried out at the University of Cagliari on samples of granite rocks from different Sardinian stone quarries. On the basis of field experiments and laboratory test data, the mechanism of diamond wire cutting has been assessed. In particular the influence of the rock features and operational variables on tool performance (cutting rate and bead wear) has been Elucidated.

Jan 1, 1992

By Louis H. Meece

The romance of the River lives on in the tales of Mark Twain; and many Americans still think of the Mississippi River in terms of the steamboats loaded with passengers, gamblers and cotton. Yet for many years, coal has been a major cargo on the American waterways. Currently, about 100 million tons a year of coal is handled in some part of its journey from mine to destination by barge. The bulk of this traffic has been on the Ohio River System and the Upper Mississippi River System in years past. Now we have a new entry. Over the past 10 years various movements of coal have developed down the Mississippi River to power plants at Memphis and along the Gulf Coast, and a small amount of metallurgical coal has moved down the Mississippi River for export to Japan since 1970. But in 1980 a brand new player came on the scene. 1980 was a momentous year for the American coal business. Historically, we have exported about 50 million tons a year of metallurgical coal to the world's steel mills. Just before and after World War I, we also had a fairly healthy export trade in steam coal; and again in the late forties, we supplied large amounts of coal to Europe until domestic production could recover from the ravages of World War II. But since the early fifties, the name of the export game has been metallurgical coal. Starting in the mid seventies, something began that was almost totally missed by the American coal industry; and that was the growth in the use of coal first in Europe and now in the Far East as a steam product and as an alternative to petroleum products. As these world coal markets began increasing, the U.S. at first was thought to be noncompetitive because ocean rates were still very low. For example, as recently as 1977, Australian coal could be moved all the way from Australia to the Gulf Coast for $12.50 per metric ton. Coal exporting countries were Poland, Australia and South Africa, except for the continuing exports of U.S. high quality metallurgical coal. But then came the second oil shock, and all of the sudden that $12.50 rate from Australia to the U.S. Gulf became $25.00. And then suddenly and almost unrecognized by the American industry, American coal was in fact competitive at overseas destinations because of the drastic change in trade patterns brought on by the doubling and tripling and quadrupling of bunker fuel prices for ships.

Jan 1, 1982

By André Carlos Silva

Dewatering stage is among the most important industrial unit operations, and is wide adopted in many different industries, due the fact that a large portion of industrial products is produced using suspensions of solids in liquids. Nowadays the mineral processing tailings disposal is a big problem due the environmental degradation produced. The phosphate rock processing in Anglo American Phosphate Brazil, situated in Catalão/Go/Brazil, generates around 180 t/h of tailings for a plant feed of 480 t/h (approximately 37,5% of the processing plant feed), with 5 to 10% of solids and approximately 14% of P2O5. Nowadays the tailings are sent direct to the tailings dam. The present work proposes the paste production using with the tailings from phosphate rock processing plant divide in two different stages. The first one composed by the free settling of the material in presence of industrial flocculants in a graduated cylinder with 2.0 L of internal volume for one hour, in the same way it must occur in conventional thickeners. After that time, the clarified liquid was drained and the remaining pulp was sent to the second stage consisting in the tailings vacuum filtration. Ten different flocculants and nine different filter media were tested. The found results were satisfactory for paste tailings production with solids percentage around 65%.

Aug 8, 2018

By F. Varley, J. Whyatt

A variety of dynamic failure cases with regional impact were described at a bump symposium held in 1958. These types of events, while rare, are of particular interest because their ability to impact a large area has disaster potential. These cases can be grouped into two broad classes of events by mechanism. These are (1) a slip along steeply dipping faults and (2) the fracturing of strong strata above or below the coal seam. Both failure modes produce dynamic or “shock” loads on the perimeter (roof, rib and floor) of mine openings. Special consideration should be given to these failure modes in the planning of deep coal mines, since their occurrence is not within the professional experience of many contemporary workers. In addition, their potential is not evaluated by many of the analysis tools commonly used to evaluate hazards in coal mine plans.

Jan 1, 2009

By John A. Rumball, Martin R. Houchin

Data from autogenous and semi-autogenous tests in a 1.67m diameter mill have been analysed in terms of a new model for rock abrasion. This model defines specific rate as the rate of production of fines (material less than 13mm) per unit mass of rock, where the term “rock” is applied to all ore pieces of ore coarser than the grate size. In most cases, an allowance for preliminary rounding and cleavage was made. A method has been developed to analyse steady-state data, using piecewise fitting to the cumulative size distributions. The model was compared to the well-established models, which are based on the population balance method. The specific rate increased for all rock sizes as the volume of 100mm balls in the mill was increased. Tests using a coarser feed and smaller balls provided further evidence that once rocks are rounded, abrasion is due to localised surface damage, caused by impacts, rather than rotational shear. An allowance for rapid rounding of jagged rocks, followed by less rapid abrasion of rounded pebbles was also tested, but the analysis was not conclusive. The average specific rate is a useful measure of the capacity of a primary mill. The effect of power intensity (kW/t of ore) was also investigated as a means of extrapolating the pilot-plant data to large production mills.

Sep 29, 2003

By Wojciech Kasprzak, Guoxian Liang, Michel Gauthier, Mickael Dolle, Yulong Liu, Xueliang Sun, Hernando Villazon Amaris, Majid Talebi-Esfandarani, Pierre Sauriol, Thomas Bibienne, Gregory S. Patience, Delin Li, Steeve Rousselot

In the 1990s, LiFePO4 (LFP) was discovered as a cathode material for lithium ion batteries and was successfully used in the variety of devices such as power tools, E-bikes and grid accumulators. New challenges associated with use of lithium ion batteries for automotive applications demand higher performance and operating requirements, yet these requirements need to be achieved at affordable cost and without compromising vehicle safety. The advantages of LFP as a cathode material include thermal stability, limited environmental impact and potential of low cost as compared to the cathode chemistries containing cobalt. Currently, solid state and hydrothermal processes are used to synthesize LFP at the industrial scale. However, they require multiple, time-consuming steps and costly precursors. Recently, a melting-casting process to produce LFP cathode material was investigated. The motivation behind this new process is the great flexibility of raw materials including chemical makeup and particle size, and the use of lower cost, commodity chemicals, with the benefits of increased kinetics in the molten state and energy efficiencies leading to overall process cost savings. Also, if successful this process could represent a novel application of conventional casting. Melting lithium-, iron- and phosphorus-bearing precursors in near stoichiometric ratios and casting LFP material that forms around 1000 °C requires fewer processing steps.

Mar 1, 2018