Search Documents

By T Nakamura, M. Itoh

Most of the used cathode ray tube (CRT) glass in Japan, which contains lead oxide, was exported and recycled in overseas factories of new CRTs. However, domestic treatment and recycling of waste CRT glass has become necessary because overseas CRT factories have shut down and exports of CRT glass have stopped. Some of the waste CRT glass recycled domestically is charged in lead blast furnaces instead of silica flux, because there is no local reproduction route for glass that contains lead. However, the mass of CRT glass that can be treated in this manner is limited because of its high silica content. Consequently, additional treatment methods for waste CRT glass are required so that more can be used as a lead smelting material. In this study, waste CRT glass was treated with hydrofluoric acid to dissolve the silica contained in the glass, and the dissolved lead was recovered by precipitation. Lead metal was recovered by electrodeposition from the prepared hexafluorosilicic acid solution.

Jan 1, 2011

By T. C. Rao, Deb Kanungo

"The results of tests carried out on a 3-in. hydrocyclone have shown the linear relationships that exist between: (1) the flow-rate of water in the feed to and the overflow product from the cyclone; (2) the flow-rate of solids in the feed to and the underflow product from the cyclone. The underflow size distribution of an operation has been found to be linear and its usefulness in evaluating particle distribution in the cyclone has been discussed. Effects of design and operating variables on the above relationships have been discussed. The performance of this 3-in. hydrocyclone has been compared with that of a 20-in. cyclone, the results for which are available in the literature."

Jan 1, 1973

By Andrea B. Baldwin

In recent years, federal and state regulatory agencies have tightened air emission standards. Two of the acid gases, hydrochloric acid (HCI) and sulfur dioxide (SO2), are under heavy scrutiny for reduction. . Most traditional scrubbing systems, i.e. wet scrubbers and spray dryers, meet the standards but they typically are high in capital cost, have significant space requirements for equipment, and are difficult to maintain. Dry sodium injection (DSI) is a alternative technology that has been shown to be effective in HCl and SO2 removal while being the inverse to the problems listed with traditional systems. This paper covers the mechanics of dry injection scrubbing using the most effective sorbents, sodium bicarbonate and mechanically-refined trona (natural sodium sesquicarbonate). It presents DSI performance data for Chambers Medical located in Hampton, SC. This facility incinerates local medical and municipal solid waste. Chambers Medical has used mechanically-fined trona for HCl and SO2 removal since late 1991.

Jan 1, 1995

By Suzanne Young

The effect of LiF additions on liqt.1id1.:1s temperature and electrical conductivity over a wide range of cryolite bath ratios (1.0 to 1.5 weight ratio) was investigated. Results did not agree with multi-regression equations reported by Dewing and Choudhary over the entire region. New regression equations were developed. Reasons? are given for the differences. The models are used to discuss the economic implications of LiF additions to Hali cell electrolytes.

Jan 1, 1985

By A. Z. Dimitroff

An improvised rock- dust disseminator, consisting of a 10-gallon galvanized metal milk can that dispenses rock dust in return air currents by the injection of compressed air has reduced the float dust explosion hazards at the Koehler coal mine, Koehler, N. Mex.

Jan 1, 1965

By Ricardo Melamed

Metallic mercury has been extensively used for gold recovery. Although the solubility and mobility of metallic mercury is low, this metal can undergo many transformations, leading to mercury contamination in humans. The complexity of Hg chemistry in the environment reflects its different possible oxidation states and species, with different physical-chemical properties. The interaction of Hg in the terrestrial system, as well as in the aquatic environment, is important to understand the mercury cycle. This paper reports data on the adsorption of Hg onto an Oxisol soil. Results show that the interaction of Hg(II) at the soil-solution interface depends strongly on ligand concentration in solution, which can affect Hg mobility. The presence of the chloride anion in solution increases the mobility of Hg(II) through the soil, due to a relative lower affmity of mercury chloride at the oxide surface. In the absence of chloride, Hg(II) form strong complexes with the surface, and its adsorption behaviour is similar to the adsorption of other hydrolizable cations.

Jan 1, 1996

By D. H. Davidson

The basic principal in the ISL process involves the recovery of metal values by moving fluids through rock instead of moving rock. The process combines surface and sub-surface operations, with the economic performance controlled by four major factors; rates of fluid injection and production from wells; the rate of mineral solubilization; the volume of rock swept by the fluid; and the volume of solution processed through the system. This paper discusses various technical and economic parameters affecting these four factors and how they impact project costs.

Jan 1, 1985

By W. L. Hollinshead

For more effective and cost saving production in tunnels, the machinery used on construction sites will be equipped with guidance systems combined with working procedure management systems. This paper describes sensors for these systems and various system configurations. A project is described which uses a computerized guidance system on an underground mining machine for guidance and profile control.

Jan 1, 1999

By Y. C. Lo

This paper presents the development of ultrasonic grinding technology for material and mineral processing. The principles underlying this new technology, as well as their implementation in two laboratory scale devices are described in detail. Ultrasonic grinding experiment results are discussed with respect to operating variables and the achieved product sizes. Special attention has been given to the electrical energy consumption of the grinder, and an attempt to compare its efficiency with tumbling mills has been made. A mechanical system capable of measuring the specific grinding energy is also described.

Jan 1, 1991

By Pengbo Chu, James Finch

Bubbles around 1 mm diameter provide the high interfacial area for capture and transport of hydrophobic particles in flotation. The formation of such fine bubbles is commonly achieved by addition of frothers that appear to simultaneously retard coalescence and promote break-up. High inorganic salt content in process water can substitute for frother. In this work we focus on the action of salt (sodium chloride) on formation of bubbles by break-up. An experimental setup that isolates break-up from coalescence was employed. A pocket of air is exposed to controlled mechanical turbulence to produce single bubbles by the induced deformation of the air and the events imaged. The presence of salt is shown to produce smaller bubbles than in water alone. Comparison with a similar study on frothers is made. The argument is advanced that the presence of frother and salt creates surface tension gradients at the air/water interface which add to the mechanical energy of the deformation and break-up process.

Jan 1, 2014

By M. Jack Snyder

The problem of effective utilization of fly ash has been given wide attention for a number of years. Although the effort devoted to the problem has led to some applications of demonstrated usefulness, the full utilization of fly ash has been held back by lack of concerted research and development activity, by lack of effective dissemination to potential users of fly ash of the knowledge that is available from laboratory and field studies, and by the obvious variability of the product. Because of the variability in fly ash from one power plant to another and from time-to-time in the same plant, specifications have been set up defining compositional or property limits within which a fly ash must fall to be used in certain applications. This paper discusses the bases for such specifications and examines them in the light of recent research on the characterization of fly ash. Other limitations and restrictions on the use of fly ash and what is being done to overcome them are also discussed.

Jan 1, 1968

By J. P. Downey, T. Salisbury, M. Berlin, E. Rosenberg, G. Pinson, R. Christianson, K. Gleason, W. Gleason, S. Davis

"The Center for Advanced Mineral and Metallurgical Processing is developing membrane production technology based on autocatalytic reduction of palladium from solution onto a unique, porous substrate. Surface membranes and catalytic structures are critically important to applications that range from hydrogen purification membranes to petroleum refining. Autocatalytic reduction processes represent a cost effective method of producing stable surface layered structures that have good working lives. These attributes are particularly important in the production of palladium alloy purification membranes used in hydrogen production. Although considerable research has investigated the interaction of hydrogen and palladium alloys, the mechanisms in play while the membranes form are not well understood. Preliminary research has identified three distinct deposition mechanisms and it appears that substantial control over the resulting membrane is possible.IntroductionPalladium-based membranes separate hydrogen from other gases because hydrogen is uniquely soluble in and readily passes through bulk palladium. As currently produced, palladium-based membranes are expensive and have short service lives. These circumstances are due in part to the lack of a complete understanding of palladium or palladium alloy deposition. The Center for Advanced Mineral and Metallurgical Processes (CAMP), in collaboration with the Metallurgical and Materials Engineering Department at Montana Tech and the Chemistry Department at the University of Montana, is engaged in the development of new methods and materials for hydrogen purification membrane production.In membrane production, the palladium requirement depends on substrate surface properties such as surface chemistry, porosity, and roughness. Thin, defect-free membranes have been successfully produced on substrates of porous glass, alumina, and stainless steel. However, the differences in the thermal expansion coefficients of palladium membranes and porous glass or alumina substrates cause problems at operating temperatures. The use of stainless steel substrates is advantageous because stainless steels have thermal expansion coefficients similar to that of palladium and they are stable at the required operating temperatures (Wicke, E., Brodowsky, H. and Ziichner, H. ). Stainless steel is also readily available and relatively inexpensive."

Jan 1, 2012

By G. R. Hopkins

The average quantity of heat needed to refine a barrel of crude oil in 1934 was 638,000 B.t.u., or about as much heat energy as contained in 5 gallons of fuel.oil. Although the total heat utilized in 1934 was slightly above 1933, crude runs to stills increased 4 percent, hence the average requirement per barrel declined from 660,000 B.t.u. in 1933 to 638,000 B.t.u. in 1934 (see fig. 1). The average for 1934 constitutes a new record for firing efficiency, being just under the previous low of 1929. Heat consumption at refineries depends on many factors, of which the trends in yields of gasoline and lubricating oils are probably most important. The yield of gasoline is indicative of activity at cracking plants, which typo of plant utilizes more thou the average amount of heat per gallon of product. The yield of lubricating oils is indicative of the extent to which crude oil is refined; that is, it takes considerably more heat to refine a barrel of crude through lubricating oils than it does to separate only gasoline and kerosene. The yield of gasoline decreased from 43.7 percent in 1933 to 43.4 percent in 1934; on the other hand, the yield of gas oil and fuel oil increased. Although the yield of lubricating oils increased slightly in 1934 the theoretical increase in fuel requirements probably was offset by technical improvements, such as solvent refining. Although no outstanding technical developments of a fuel-saving nature were made in 1934, some progress undoubtedly was recorded. Heat exchangers, an effective fuel-saving device, wore enlarged, and some refiners now take off several cuts before the crude reaches the pipe stills. The total capacity of pipe stills increased 2.5 percent in 1934, and many of the less efficient shell stills were torn out.

Jan 1, 1935

By B. M. Davis

The problem of assessing uncertainty in grade estimates has been a topic of research and debate since kriging was first introduced. Use of the kriging variance was originally touted as all that was necessary in order to produce confidence limits for grade estimates. Since then the prudence of using the kriging variance for confidence interval estimation has been questioned, and techniques such as the jackknife and conditional simulation have been proposed to develop "true" interval estimates. This paper compares the differences between interval estimates produced by the three methods and makes conclusions about the performance of confidence intervals produced by the different methods.

Jan 1, 1997

By J. K. Williams, M. P. Wells

"As part of the planning system at each division of Nchanga Consolidated Copper Mines, Limited, the Mine Planning Department is required to produce a detailed production schedule for each shaft.Because of the difficulties in producing a schedule which satisfies all the mining constraints, and because of the large clerical effort involved, the full range of possible schedules can never be considered.It has been found possible to produce a schedule using linear programming which satisfies the majority of the many varied mining constraints. Computer programs have been written to enable the mine planning department to use this mathematical system without assistance.The system has a large degree of flexibility to enable the planner to include conditions which cannot be incorporated readily in the linear program. This system permits the more efficient production and evaluation of schedules and reduces the amount of clerical effort."

Jan 1, 2014

By James R. Hunter, Sandra K. Zacharias, Ursula M. Franklin

Archaeometallurgical remains can be a valuable source of information about past technological activities and, by inference, the societies that undertook them. Material traces of former metal-producing or metal-working centres can include raw materials, products, or metallurgical installations such as mines, furnaces or forges. Of these remains, the most common is slag, often left undisturbed since its original production. Physical and chemical analyses of archaeological slag and metal can often reveal the processes and materials involved in their formation. Mineral composition and softening temperature of a slag, for instance, can indicate the conditions of the metallurgical operation, such as temperature and atmosphere and, thus, help identify metallurgical processes which took place at a site(1). The present report illustrates the value of such analysis. Metal-working remains from Sainte-Marie among the Hurons, near Midland, Ontario, on the south side of Georgian Bay have been analyzed in order to determine the techniques and processes used by the 17th-century blacksmith who worked at the mission headquarters from 1642 to 1649. Samples were selected from a very large collection of blacksmith refuse which was excavated from the site by archaeologist Kenneth Kidd in 1941-42(2).

Jan 1, 1999

By Chen Wen, Li Zhao-jia, Zhao Qiang, Ning Shun-ming, Tang Sanchuan, Wang Hong-qiang

"The carbon-burdened and cold-bonded pelletizing-electrosmelting process is used to dispose low-grade manganese, and the qualified rich-manganese slag is obtained. On the condition that reduction roasting temperature was 1000?, reduction time was 45min, particle-size was -1mm, reductant dosage was 1.6%, basicity was 0.3, smelting temperature was 1410?, smelting time was 60min, it had a good effect on the melting between slag and metallographic phase, the manganese content was 32.58%, manganese recovery was 92.16% in the slag; while the iron content was 94.40%, iron recovery was 95.32% in the metallographic phase. It was proved by the demonstration tests.IntroductionManganese is an important raw material for steelmaking, which is extensively utilized in modern industry, the consumption of manganese for iron and steel industry accounts for 90% to 95%. After mining over 30 years, the high-grade manganese resources drop markedly, especially with the hypergrowth of steel industry, the domestic manganese is far from the requirement, as a result, we have to buy significant quantities of manganese overseas. Besides, the property of imported manganese is more and more complex, and the high-grade and lump manganese decrease year by year, while the fines and high-crystal water manganese are on the increase. Therefore, how to make effective use of domestic low-grade manganese and intensify the manganese’s smelting is an effective approach to reduce the cost of manganese series ferroalloy and improves market competitiveness[1-4]. It has important practical meaning."

Jan 1, 2012

By E. Viljamaa

In this research, earlier developed information integration method and novel web technologies are applied to intensify infrastructure construction process control. The applied method uses semantic methods to integrate scattered information that is later on exploited by process management using state-of-the-art web technologies. The applied method and web technologies not only improve the process management situation awareness by integrated up-todate multi-source process data but also provide platform independent access and visualization tool for process data. Utilization of such technologies potentially lead on cost savings, make processes safer and also more environmentally friendly. The integration method also enables intelligent queries to the integrated data making possible to use machine based inferring to the data.

Aug 1, 2013

Fault detection and identification are major challenges in process engineering and manufacturing and the key component of abnormal event management systems. Timely detection, diagnosis and rectification of abnormal or faulty process conditions can lead to savings of billions of dollars in equipment damage and lost productivity, not to mention the prevention of injury and loss of human life associated with industrial accidents. A major contributing factor to current losses in industry is the reliance on human operators to interpret high-frequency samples from hundreds or thousands of variables simultaneously. As a result, the automation of fault detection and diagnosis is seen as crucial to the successful implementation of abnormal event management, the need for which is becoming all the more urgent given the increased complexity associated with modem industrial plants. In this paper, a methodology for process monitoring that uses support vector methods to extract nonlinear features from data is discussed and applied in the diagnostic monitoring of an industrial liquid-liquid extraction column.

Jan 1, 2005

By S. Mamonov, V. ?shikhin

"The purpose of work was the significant increase of copper recovery from slag at a concentrating plant. Analysis of study of slag phase composition showed the perspective of a slow slag cooling method due to its recrystallization and transition of primary copper minerals to secondary.Copper content in base slag varied between 0.71 and 0.96%. The study of a degree of copper minerals release of the slowly cooled slag in comparison with a yielding slag showed that in a flotation size grade –0.071 mm of yielding slag the weight ratio of released copper minerals grains is 58.95% against 86.73% in samples of slowly cooled slag. The process flotation sheet consists of three main, one control and two cleaner flotation operations with aftergrinding of middling products. A reagent mode was differed from a factory one by decreasing the slurry pH from 11–12 to 8–9. This paper shows research results of the slurry alkalinity impact on technological indexes of beneficiation (flotation).Industrial testing of a resulted batch of slowly cooled slag at “SUMZ” concentrating plant showed the efficiency of such processing: copper recovery to a copper concentrate increased by 15–19%.INTRODUCTIONIntensive development of mining and metallurgy industries within a 250-year period in the Ural region led to forming of approximately 315 man-made mineral formations at the territory of the Sverdlovsk region. The region contain over 32.5 billion tons of barren rocks and out of balance ores, over 1.5 billion tons of tailings, over 115 million tons of slimes, and over 100 million tons of metallurgical slag (Demin et al., 2000). Latters, at average, contain 407 thousand tons of copper, 2519 thousand tons of zinc, 7 tons of gold, and 150 tons of silver (Rudoy et al., 2011). Wastes generated in mining processing and metallurgical sector of economy contain not only thousands tons of copper and zinc, but cause significant damage to the environment where they are located. The reduction of negative impact of anthropogenic wastes on the environment as well as the storage volume reduction of valuable metals from dump slags is possible by improving the efficiency of the melting and further flotation of slags formed during this process."

Jan 1, 2016