Search Documents

By Ad. Breyre

For more than 20 years, Belgium, leading all the coal-mining countries, has made increasing use of sheathed explosives, which wore first suggested by the late E. Lemaire, predecessor of the author gas Director of the Institut National des Mines. It appears to the author that it will be valuable to show how the use of sheathed explosives has developed in Belgium, how the various difficulties encountered in their manufacture have been overcome gradually, and the tyros of sheathing that have survived and the reasons for their survival.

Jan 1, 1940

By Thomas L. Kesler

IF all of the 14 million tons of kaolin produced in Georgia through 1949 had been mined from a single deposit 20 ft thick, it would represent a mined-out area of less than 1 sq mile. This measure of depletion is in such strong contrast with the large size of the area shown in Fig. 1, from which most of the output has come, that there has developed an optimistic outlook concerning future supplies of kaolin equal in grade to that already mined. Dozens of mines are widely but not evenly distributed within this area, which consists mostly of parts of Twiggs, Wilkinson, and Washington counties. There are scarcely half a dozen kaolin mines elsewhere in the state that have been appreciably productive, although the areas in which they occur may have good possibilities. Most of the efforts to find new deposits, therefore, will be confined to the area shown in Fig. 1, for it is here that the industry has established its facilities, and prospecting is encouraged by relatively numerous outcrops and opened deposits of kaolin.

Jan 10, 1951

By D. T. Iseley, A. L. Atta-alla

INTRODUCTION The extension project of the East Line Subway of Atlanta's subway network includes the construction of two single track transit tunnels under Interstate Highway 285. The project will be in DeKalb County, Georgia. The length, width, and height of each tunnel are 54.25, 6.3, and 7.2 m (178, 21, and 23 ft) respectively. The ground cover above the tunnel crown ranges from 1.5 to 3.25 m (5 to 11 ft). A soil pillar about 5.5 m (18 ft) wide will remain between the tunnels. The construction of each tunnel includes (i) installation of 21 steel soil support pipes of 75 cm (30 in) diameter, (ii) jet grouting 15 soil cement shafts of 60 cm (24 in) diameter in the soil under the pipes, (iii) contact grouting behind the tunnel lining and between soil support pipes and pavement, (iv) excavation of soil inside the soil support arch, and (v) installation of steel pile foundation, steel sets, and permanent tunnel lining of cast-in-place concrete, all as shown on the cross section in Fig. 1. The soil profile can be described from top to bottom as cement/asphalt concrete pavement, a fill layer consisting mostly of stiff sandy silt/firm silty sand, a residual soil layer consisting mostly of silty sand/sandy silt, partially weathered rock, and solid rock.

Jan 1, 1991

By J. P. Gliddon

Since 1980 a number of significant changes have been introduced at Palabora in an effort to off-set the effects of reduced product price and increased unit cost of inputs. These changes and improvements include major equipment rationalization programs, the introduction of trolley assisted truck haulage, adoption of a sophisticated computerized truck control system, pit design enhancements, improved drilling practices, use of emulsion explosives and the installation of an in-pit crushing and conveying system. The various changes, their effect on the operation and their contribution to cost reduction and improved productivity at Palabora are considered.

Jan 1, 1987

By Ad. Breyre

For more than 20 years, Belgium, leading all the coal-mining countries, has made increasing use of sheathed explosives, which wore first suggested by the late E. Lemaire, predecessor of the author as Director of the Institut National des Mines. It appears to the author that it will be valuable to show how the use of sheathed explosives has developed in Belgium, hour the various difficulties encountered in their manufacture have been overcome gradually, and the tyres of sheathing that have survived and the reasons for their survival.

Jan 1, 1940

By Y Yang, J Skrypniuk

The Jinfeng mine is Sino Gold's flagship project and is the second largest gold mine in China. Sino Gold Limited (SGL) holds 82 per cent equity in the Sino-Foreign joint venture Sino Guizhou Jinfeng Mining Limited (SGJML) with a Chinese partner. Jinfeng is located in a relatively remote site in southwestern Guizhou province. The orebody is considered to be the largest known Carlin type deposit in China. Jinfeng Plant has the world's third largest BIOX« bacterial oxidation facilities (790 t/d), treating highly refractory concentrate generated from crushing, semi-autogenous grinding (SAG) and ball milling and bulk sulfide flotation operations. The Jinfeng Plant construction started in February 2005, commissioning was completed in April 2007, and commercial gold production was achieved in September 2007. This paper describes the successful operations of Jinfeng Plant over the last two years. The key events of the project development are described, from the project background and process design, through to the commissioning and achieving design mill throughput of 3600 t/d resulting 180 000 ounces of gold per year. Process aspects of the BIOX« and carbon-in-leach (CIL) operations over the last two years are discussed which illustrate a very high BIOX« oxidation rate (more that 97 per cent) and excellent CIL recovery (more than 96 per cent). The management of the Jinfeng plant CIL tailings detoxification and filtration is described, and Jinfeng has became the first BIOX« processing plant to have achieved dry stacking of detoxified and pressure filtered CIL tailings. Current efforts to recover cyanide from CIL detoxified solution and the achievement of a zero discharge site water balance are also introduced. Many improvement projects have been made over the last two years which have culminated in a 15 per cent increase in mill throughput over the design and BIOX« CIL recovery increasing from 92.5 per cent to 96 per cent. Significant operating cost reductions from lowered of acid, lime and cyanide usage through process modifications and technical innovations are discussed.

Jan 1, 2009

By João Luiz do Vale

In standard wear tests, such as pin on disk (ASTM-G99) or block on ring (ASTM-G77), the apparatus simulates conditions that are often different from a machine element real application. Therefore, for an accurate investigation of a tribological application, it is essential to test the real condition in which there are similarities as: geometry, contact details, force application mode, materials, among others. It emphasizes that for studies involving polymeric materials it becomes extremely relevant. Thus, the Laboratory of Surfaces and Contact (LASC) at UTFPR developed an apparatus for sliding bearing on shaft test. In that equipment, loads are applied by a dead-weight system and the frictional force is measured on a load cell. The apparatus operating ranges for load added to the dead weight system and rotation shaft are from 0.2 to 5.0 kgf and from 260 to 3500 rpm, respectively. This paper presents a detailed evaluation of such apparatus, which includes free-body diagrams analysis and a deduction to obtain an equation for the kinetic friction coefficient. Also, the standard measurement uncertainties of a caliper, an electronic scale, and a cell load were determined. It was verified that the kinetic friction coefficient equation is dependent on the apparatus geometry, the applied load, and the frictional force value. Additionally, through the statistical significance analysis it was concluded that some terms in the equation were not significant. Finally, through the application of the error propagation theory in the kinetic friction coefficient equation, the standard measurement uncertainty of the apparatus which showed a value nearby 0.002 along the operating range of the apparatus was obtained.

Jul 31, 2018

By J. C. Cawley, G. T. Homce

The U.S. National Institute for Occupational Safety and Health (NIOSH) Office of Mine Safety and Health Research (OMSHR) conducted a study of mining industry electrical injuries reported to the U.S. Mine Safety and Health Administration (MSHA) for the years 2000 to 2009. The findings of that study are detailed in this paper, and serve to characterize the circumstances surrounding electrical injuries and identify causal factors. The study included three tasks: 1) a direct review of mining industry occupational injury data compiled by MSHA, 2) interpretation of the narrative descriptions available for the injuries (from MSHA data) and 3) a separate examination of fatal electrical injuries. Eight-hundred sixty-five electrical injuries were reported during the 10-year period studied, with 39 of those being fatalities. This makes electrical injuries disproportionately fatal with respect to most other types of injuries in mining. Electrical injury rates were higher in coal mining than noncoal mining and, within the coal sector, rates were higher in underground operations than in surface operations. Of the 865 total cases, electrical and machine maintenance or repair activities were involved in 580 (69%), and electricians and mechanics were injured in 362 cases (42%). Of the 39 fatal electrical injuries, 27 (69%) involved electrical maintenance or repair work, and in 21 of these 27 cases, the failure to de-energize, lock-out and tag the circuit was the cause or a contributing factor. Also, contractor employees had a much greater chance of an electrical injury being fatal than did mine operator employees. The top three root causes for fatal electrical injuries were 1) no or inadequate lock-out and tagging, 2) failure of power system components and 3) contact of overhead electrical power lines by mobile equipment.

Jan 1, 2013

By R. V. Ramani, K. V. Raj, S. Bandopadhyay

The air flow problems in openpit mines are complex. Computational fluid dynamics (CFD) models can provide detailed information regarding air flow pattern, velocity distribution, temperature, and pollutant concentration in an enclosed domain of an openpit mine. A range of turbulent models can be selected with varying complexity and accuracy. Pollutant transport models, however, differ in their assumptions and structure as well as in the algorithms they use. As a result, predictions vary from model to model. This paper presents a study of pollutant transport in an actual openpit mine under a stable boundary layer. The objective was to test two turbulence models using similar geometry and the same input conditions and model constants. Measured data were used to compare the results of the two CFD models, namely, the kappa-epsilon (к-є) model and the Large Eddy Simulation model. Despite the complex synoptic situations, different meteorological input data and fast-changing conditions, the simulation results from both the models were in good agreement regarding the dispersion of pollutants.

Jan 1, 2015

By P Holtham, K Duffy, B, W Valery, E Tabosa, rade

Pre-concentration has potential to significantly improve Mineral Resource efficiency by removing gangue early in the process, before energy intensive and expensive comminution and fine processing. However, there are numerous options for pre-concentration and the performance and benefits of these are very case specific. To determine the best option for a particular deposit and to successfully integrate it into the overall mining and processing operations requires comprehensive evaluation. This needs to consider orebody suitability, technology capability and economic viability. The in-situ variability of a deposit and how it is influenced by mining methods and the liberation size of gangue are key factors which are generally not well understood. Geostatistical methods provide an insight into orebody variability, and the overall selection of any pre-concentration solution must be an integrated approach between geology, mining and processing. Many pre-concentration evaluations investigate the potential of just one option. Technology selection should start wide and may include: selective mining, pre-screening (with or without selective blasting), sorting (bulk and or particle), coarse gravity separation (e.g. jigging, DMS), coarse particle flotation, magnetic separation, etc. The upgrade performance of these processes is very ore specific and should be determined from testing, with detailed multi-component modelling used to determine the overall process performance. Many of these pre-concentration processes require significant ancillary equipment, feed preparation and materials handling. It is important to realistically estimate all costs to understand overall economics and select the best option. Some examples showing evaluation and comparison of pre-concentration options are presented in this paper. These include assessments of in-situ variability using geostatistical tools, process modelling of pre-concentration options and overall performance, preliminary layouts and cost estimates, and economic evaluations.

Nov 10, 2020

By M Akhtar, E Jak, M Shevchenko

This article presents an overview of the experimental phase equilibria studies of S-containing systems (Ni-Sn-S, Cu-Sb-S, and Cu-Sn-S) and As-containing systems (Fe-Sb-As and Fe-Sn-As). These systems improve the prediction capabilities of FactSage in a 20-component ‘Cu2O’-PbO-ZnOFeO- Fe2O3-CaO-SiO2-S-(Al2O3-MgO-CrO-Cr2O3-Na2O)-(As, Sn, Sb, Bi, Ag, Au, Ni, Co) system for complex pyrometallurgical operations during both refining and recycling. Experiments involved equilibration at predetermined temperatures (300–1200°C) with or without preheating, followed by rapid quenching in a brine. Quenched samples were then directly measured using an electron probe microanalyser. For the Ni-Sn-S system, liquid phases (NiS- and SnS-rich mattes and liquid metal) and solid phases (Ni1+xSn, SnS, Ni3Sn, FCC-Ni, Ni1-xS, NiS2, Ni3Sn4, SnS2, Sn2S3 and β-Ni3S2) were observed. A new Ni3Sn2S2 phase was found to melt incongruently. For the Cu-Sb-S system, liquid metal, matte, FCC-Cu, digenite, Sb, CuSbS2, Cu3SbS3 and Cu3SbS4 phases were observed. For the Cu-Sn-S system, liquid metal, matte, digenite, SnS and Cu3Sn phases were found at liquidus.

Jun 17, 2024

By Jacob Mathis, Mark Bradford, Alston Noronha, R. M. True

In June 2022, Louisville MSD completed a 6.5-km (4.0-mi), 6.1-m (20-ft.) diameter CSO conveyance and storage tunnel system located along the Ohio River in downtown Louisville, Kentucky. For large diameter shaft and tunnel construction, drill-and-blast operations among other methodologies were used in close proximity to federal, commercial, and residential properties with no impact to stakeholder infrastructure. s one of the rst maor tunneling proects in Louisvilles metropolitan area, this paper explores Black & Veatchs rigorous geotechnical instrumentation monitoring program that provided uality assurance for local stakeholders and afrmed innovative tunneling solutions can be successfully executed in an urban setting.

Jun 23, 2024

By Botond Beno, Dave Watson, Danny Read

The Hampton Roads Bridge-Tunnel (HRBT) Expansion widens the existing I-64 four-lane bridge-tunnel corridor to eight lanes through construction of two parallel tunnels, interstate widening, and bridge expansions. The design-build contract was awarded to Hampton Roads Connector Partners with HDR and Mott MacDonald retained as lead designers in a Design Joint Venture. This paper will highlight some of the e challenges related to the design of the twin bored tunnels from spaceproong, tunnel enabling wors, segmental lining design and durability considerations.

Jun 23, 2024

By A. Golder, S. P. Dandapat, I. Roy

One of the consequences of large-scale opencast mining for coal is the disposal of an enormous volume of overburden material that needs to be removed. With the enlargement of opencast mines and associated high stripping ratios, the volume of overburden extraction is rising. Overburden from the initial mine cut has to be necessarily dumped outside the mining area until enough void is created inside the mine for back-filling operations. The quantity of overburden placed outside the mining area normally varies from 10% to 30% of the total overburden removal. The stability of these dumps placed outside the mining area is of prime importance from the point of view of smooth operations of the mines and safety of persons in and around the dumping area. Owing to increasing pressure on land use, mine operators do not have any other option other than to place the waste dumps very near to the surface edge of the pit, which may lead to failure of the topsoil benches of the working pit. This study identified major controlling parameters that influence a stable but economic combination of height and slope angle of external dumps located close to the edge of an open coal pit.

Nov 27, 2024

By Oren C. Baptist, Carlon S. Land, Eliot J. White

The water sensitivity of the oil - gas - producing sandstones in three fields in the Patrick Draw area of southwestern Wyoming was estimated by laboratory testing . The tests used to estimate sensitivity , which is a measure of the loss of well productivity if the producing formation is invaded by fresh water , are : Porosity ; permeability to gas , water , and brines ; saturation characteristics with air displacing water from the samples and by mercury injection ; and identification of clay minerals by X - ray diffraction . Laboratory results indicate that the degree of water sensitivity of the sands in the Patrick Draw, Table Rock , and Desert Springs fields vary , in that order , from moderately sensitive to highly sensitive . The main cause of the sensitivity appears to be the movement of fine particles in the pores , but the swelling of a small amount of an expandible clay mineral may also contribute to the permeability reduction observed in the samples . Laboratory results further indicate that the permeability of the sands to fresh water is seriously reduced if they are first flushed with sodium chloride brine ; calcium chloride brine is less harmful to the sands than sodium chloride brine . The low original permeability of the oil sand in the Patrick Draw field , together with its moderate sensitivity , indicate that the rate of water injection for the secondary recovery of oil will be low . Limited field experience in two pilot - injection wells confirms this prediction .

Jan 1, 1964

By Michael G. Zabetakis, Israel Liebman, Henry E. Perlee

Flammability studies conducted to date on stratified methane - air and pentane - air mixtures in air indicate that location and extent of a flammable layer are affected by molecular diffusion , gas motion , and propagation of flame . In initially quiescent mixtures , the lower limit - of - flammability zone may be determined by assuming molecular diffusion alone governs mixing rate . The upper limit - of - flammability zone can be predicted in this manner only for stratified layers with small concentration gradients ( less than 0.2 volumepercent per inch ) ; where large concentration gradients are encountered ( for example , as much as 30 volume - percent per inch ) , the initial - mixture methane concentrations that yield flammable mixtures are larger than anticipated . Flames propagating through heterogeneous quiescent methane - air atmospheres in the direction of the concentration gradient exhibit flame speeds at any point that corresponds to the flame speed of the homogeneous gas mixture having the same gas composition as that of the point in the heterogeneous system . In flowing mixtures with large concentration gradients , the degree of mixing prior to ignition does not appear to affect the flame velocity and emitted radiation appreciably in a 6.5 - ft - diameter gallery .

Jan 1, 1964

By A F. Cropp, D J. Bradshaw, W R. Goodall

Mineralogy and critically the texture of both the ore and gangue phases are of paramount importance in the flotation recovery of copper from porphyry ores. Mineralogy and texture will define the theoretical grade recovery curve for a feed ore. Actual grade-recovery falling below this may be due to texture and gangue influences, whilst desired grade-recovery above this line will not be possible unless the characteristics of the feed are altered.This review discusses examples of porphyry copper deposits where process mineralogy has been used to characterise these textural and gangue influences on recovery by flotation. More specifically, the influence exerted by grain size, liberation, association and elemental distribution is explored. The implications of these on overall plant philosophy and operation are highlighted, along with the subsequent potential impact on recovery.CITATION:Cropp, A F, Goodall, W R and Bradshaw, D J, 2013. The influence of textural variation and gangue mineralogy on recovery of copper by flotation from porphyry ore - a review, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013 , pp 279-292 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 29, 2013

By Vincent A. Scovazzo

During the winter months of late 1985 and early 1986, residents along Dry Fork near Grundy, Virginia (United States) experienced seismic events that they attributed to longwall mining at Island Creek Corporation’s (Island Creek) Virginia Pocahontas Mine No. 3 (VP-3 mine). Island Creek contacted STS D’Appolonia Ltd. (STSDL) on March 7, 1986, to investigate these events. An STSDL representative, Vincent Scovazzo, interviewed residents of Dry Fork on March 10, 1986. It was noted that only people within a residential structure felt the events they described as house shaking, vibrating walls, and ceramics falling from shelves. STSDL representative installed a blast monitor at a residence. Within 2 days, various events were recorded. Some could be attributed to truck and heavy equipment movement. Eight events had no obvious cause but appeared on resident’s written logs as earthquakes caused by mining. STSDL contacted Utah Geophysical, Inc. who had developed a technique to determine the mode of rock failure using the seismic record. Utah Geophysical was engaged to install and monitor a microseismic network, locate the epicenter of the events, and work with STSDL in determining modes of failure. The network was comprised of six geophones located at five stations. Data was recorded for 24 days from May 20 through June 13, 1986. The data was filtered to eliminate events determined to have an origin other than the longwall panels’ overburden and under-burden. The larger events from this filtered data set were selected and analyzed to determine their hypocenter locations, time of occurrence, magnitudes, and failure mode. Processed data was interpreted, tabulated, and plotted by STSDL to provide information relative to the sources of the seismic vibrations and their possible relationship to the mining operation.

Jul 1, 2023

By T. C. Huber

The southern African region has a high concentration of mineral resources and supplies much of the world?s platinum demand. As a result, the international community watches South Africa to understand the impact of supply on global markets. An analysis of supply certainty and risk plays a key role in the future of growing demand in various sectors. The southern African platinum industry experienced substantial growth in the early part of the 21st century, resulting in bullish forecasts for growth during the period of 2000?2006. However, southern African platinum producers saw a significant drop in production over the following three years as a result of many dynamic factors in operations and the global economy. Between 2006 and 2009 there was a million-ounce shortfall between forecast and actual production. This was raised as a concern at the Fourth International Platinum Conference in 2010 by Stephen Forrest during his keynote address, specifically regarding the lack of understanding in the market of the causes of this shortfall and any action that was being taken to address them. This paper reviews publicly available information in the media and corporate reports and communications for the period January 2006 to December 2009. In addition, several interviews were held with key stakeholders in the industry to provide further perspective. The paper then highlights the main reasons that are reported to have affected the loss in production over the period and discusses the possible implications of the information that the mining industry does and does not disclose regarding platinum supply.

Jan 1, 2012

By K. B. Owusu, W. Skinner, R. K. Asamoah, J. Karageorgos, M. Zanin, C. Greet

High Pressure Grinding Rolls (HPGR) are mostly used prior to pelletising processes to increase the specific surface area (SSA) of iron ore concentrate. For expressing SSA, the Blaine index is utilised as one of the most important dimensional properties of iron ore pellet feed. ISO 21283 is a standard test method that explains the manual of Blaine air-permeability apparatus for determination of this parameter. In this standard, the disaggregation method is based on passing the minus of 1 mm samples from the 0.150 mm sieve. The disaggregation process has an effective role on the results of Blaine airpermeability test especially for regrinding HPGR products. In this research, firstly the Blaine index of samples was measured without disaggregation. Following this, disaggregation was done by passing the minus of 1 mm samples through three sieves with different dimensions, 0.150, 0.090 and 0.045 mm, separately, and the Blaine index was calculated for each one. Finally, lab-mill with rubber balls, called Jar mill, was investigated as another option. Screen analysis and image analysis with SEM were performed to evaluate the effects of the sample's disaggregation on the size distribution and agglomeration of samples. The results showed that the disaggregation method with sieve size 0.150 mm, according to ISO 21283, was not applicable for HPGR products because the particles were still stuck together. In addition, the disaggregation method with the sieve size 0.045 mm or with Jar mill offered reasonable results. Keywords: Disaggregation, Blaine index, specific surface area, regrinding HPGR, ISO 21283, Jar mill

Jan 1, 2020