Search Documents

By J. D. Mote, A. Rosen, J. E. Dorn

The effect of strain rate and temperature on the critical resolved shear stress for (1100) [1120] prismatic slip was determined for the intermediate hexagonal phase containing about 67 at. pct Ag and 33 at. pct Al. Whereas the flow stress increased only slightly as the test temperature was first decreased below room temperature, a rapid increase inflow stress was obtained with yet greater decreases in temperature from about 240" to 4°K. The effect of both temperature and strain rate on the flow stress over the low-temperature range could be completely rationalized in terms of the Peierls mechanism when the deformation is controlled by the rate of nucleation of pairs of kinks. A few years ago Mote, Tanaka, and Dorn1 observed that the critical resolved shear stress for prismatic slip of a 67 at. pct Ag plus 33 at. pct A1 hexagonal intermediate phase by the (1100)[1120] mode decreased precipitously as the test temperature was increased from 4" to about 160°K. Their results for both basal and prismatic slip are given in Fig. 1. It is obvious that only the flow stress for prismatic slip is strongly temperature-dependent, whereas the flow stress for basal slip is independent of temperature. If the temperature dependence of the flow stress were primarily due to interstitial impurities, it might be expected that they would influence the flow stress for basal slip as well. Since the activation volume at 115°K for prismatic slip was determined to be about 15b3, where b is the Burgers' vector, this thermally activated deformation process was tentatively ascribed as being due to the Peierls mechanism. But the various analyses of the Peierls mechanism then available as formulated by Seeger2 and also by Lothe and Hirth3 did not agree well with the experimental data. Since that time a more realistic theory for the operation of the Peierls mechanism under conditions where the strain rate is determined by the rate of nucleation of pairs of kinks has been presented by Dorn and Rajnak.4 The present investigation was, therefore, undertaken in order to provide the essential data for a careful check on the agreement between this theory and the low-temperature deformation by prismatid slip of the above-mentioned Ag2A1 intermediate phase. EXPERIMENTAL TECHNIQUE Single-crystal specimens so oriented that the [1120] direction and the normal to the (1100) plane were at 45 * 2 deg to the tensile axis were grown from the congruent melting composition of about Ag2Al for the intermediate hexagonal phase by the

Jan 1, 1964

By John D. Sullivan, Edwin J. Rogers, Chester R. Austin

The problem of making a building unit combining the necessary physical and mechanical properties and good thermal insulation has been foremost in the minds of architects and ceramic and construction engineers for many years. This paper presents the results of studies on thermally expanding shales or clays to produce lightweight cellular products suitable for making building units. An expanded clay block suitable for building purposes should be large enough qo that substantial savings may be effected in labor costs in laying the wall. The permeability should be low and it should have sufficiently good "dry-wall" characteristics to permit exposing the exterior surface to the elements, and to permit plastering directly the inside wall surface. The thermal conductivity should be low and the mechanical properties should be adequate. Obviously, a unit possessing satisfactory qualities for constructing an - outside wall would be satisfactory for interior walls and for back-up purposes. The results of studies on bloating various shales or clays† and the properties of the expanded products are reported. In another paper1 basic factors involved in bloating of clays are discussed. Manufacturers of ceramic products, partitularly structural clay, may encounter bloating of the ware during burning, and precautions must be followed to avoid this phenomenon. About 1927 the C. F. Burgess Laboratories, Madison, Wis., while carrying on an investigation for the American Face Brick Research Corporation, conceived the idea of intentionally bloating clay while holding it in a restrained condition, with the hope of producing a unitary cellular mass. Work was carried on until about 1931, when studies were terminated because of business conditions. These studies were continued later by The Western Brick Co., Danville, Ill., which developed a process of "inwardly expansive bloating."² The major purpose of the latter investigation was to produce back-up tile to compete with concrete blocks made from Haydite or cinder aggregate. Haydite is a light-weight aggregate formed by heating certain clays or shales rapidly in a rotary kiln. While the investigations at the C. F. Burgess Laboratories or at Western Brick Co. were not carried far enough to lead to the commercial production of material for the construction of walls, particularly outside walls, they showed that certain clays could be thermally expanded and that it was possible to produce a material of low permeability with a large percentage of the total voids or cells closed. commencing in 1939, the Ozark Chemical Co. sponsored a research program at Battelle Memorial Institute for the Purpose Of determining whether it is technically feasible to make thermally expanded building units, and specifically to get answers to the following questions:

Jan 1, 1942

By J. Rogers, K. L. Sutherland

The relationships between collector and mineral, activator and mineral, and activator, collector and mineral will be considered herein. We propose to criticize current theories of flotation but we will not repeat the many pertinent arguments presented by Wark and Cox28 in 1937 in which the "chemical" or more strictly the "solubility" theory proposed by Taggart and co-workers22 is shown to be untenable. Recently Taggart, Arbiter and Kellogg24 have studied the long-chain aliphatic amines as collectors and have attempted to resuscitate the solubility theory for these particular collectors. Dean and Ambrose3 have felt that "we stumble over words" when we distinguish different mechanisms of adsorption. Our view is that nothing is more stultifying to the development of a science than attempts to force widely different phenomena into one classification. This oversimplification leads immediately to difficulties in the interpretation of results. Experimental Procedure The response of minerals to activator and collector was determined by "captive-bubble" tests. The methods of preparation of specimens26 and of testingin have been previously described. Results from captive-bubble tests were confirmed by flotation tests in glass-stoppered cylinders.26 The full lines shown in the figures relating solution composition to contact (flotation) distinguish solutions in which contact (flotation) is possible from those in which it is not. The curve is derived by successive approximation and the accuracy is ±o.2 pH units and ±5 mg. per liter of collector or depressant. Solution compositions for which it was shown experimentally that contact or flotation is possible are marked by a circle, those for which it is not possible by a cross and those for which it is doubtful by a cross within a circle. It is assumed that at all other solution compositions within (without) the curve, contact or flotation is possible (not possible). After testing in the collector solution, the mineral was removed, washed, and tested by the captive-bubble method in water, or floated in a cylinder with frother only. In this way the composition of solutions in which a mineral was conditioned but in which properties of the collector solution prevented contact or flotation can be defined. The composition of solutions in which conditioning was possible lie between the full and broken curve, the experimental results being indicated on the figures by a square. The curves show the limits of composition of solution in which flotation in a cell would be possible. Many factors other than those considered in these tests determine recovery or grade of a given mineral in practice.

Jan 1, 1947

By N. D. Policow, J. S. Orphanos

D.A. Dahlstrom In the paper, a comparison was made between flowsheets using the screen bowl centrifuge and disc filters, respectively, as the primary dewatering device. The authors very effectively show that by raising feed temperature, mechanical dewatering is enhanced through reduced viscosity of the water. When a final coal moisture of 10% is required, the net effect of heating the feed is a reduction in thermal requirements because of the lower evaporated load on the dryer. The flowsheet comparison on this, however, was not completely correct. Disc filters do not generally utilize enhanced mechanical dewatering through increased temperature. Horizontal belt filters, through the optimal use of steam heating of the filter cake, have shown significant cost reductions over disc filters where steam is not used. In addition, the authors forgot to mention that there is a certain fraction of the feed that is so fine that it cannot be recovered by the centrifuge economically. That is the function of the filtration device shown in Fig. 4. In subbituminous pipeline coals, this fraction represents more than 10% of the feed. Even after flocculation and belt pressing, the moisture content in the fine fraction is 30%-40. Recent tests on a subbituminous pipeline coal slurry, compared an Eimco-Extractor horizontal belt filter with the screen bowl centrifuge flowsheet shown in Fig. 4. Mechanical dewatering was enhanced through the use of a steam dry zone after the initial dewatering zone. Vacuum pump horsepower was reduced by more than 50% through the use of condensors, and heat recovery was utilized to minimize thermal costs. Thermal drying to 10% moisture by weight was required in both flowsheets. The 0.5 wt% fines in the filtrate were flocculated and recycled to the filter, thus eliminating the belt press and solids mixers. When the three major operating costs (which normally account for 50%-75% of the coal operating costs) of steam, electricity, and flocculants at current prices were calculated, the flowsheets utilizing the Eimco-Extractor had cost savings vs the centrifuge flowsheet of 89¢/t (81o; per st) of surface dry coal. This advantage increases with increasing thermal and electricity prices. I congratulate the authors for the strides made with the screen bowl centrifuge. However, filtration flowsheets continue to be improved and their simplicity and low thermal and electrical requirements should not be so quickly dismissed. ? Reply by N.D. Policow From a technical standpoint, a number of extensive test programs have demonstrated that by raising the feed temperature, mechanical dewatering is enhanced whether it be centrifuges or filters performing the separation. Economic constraints usually become the over-riding issue. If an inexpensive source of thermal energy is available, i.e., waste steam, etc., the approach becomes commercially acceptable. For the specific case of coal slurry pipelines, since the dewatering plants will be located close to power generation stations, the preheating approach becomes especially attractive. The cost comparison shown in Fig. 7, which was prepared by a major West Coast engineering firm, contrasted screen bowl centrifuges and disc filters. In both alternatives, a thermal dryer was specified to produce a contract moisture of the final product. Sizing of the thermal dryer on the screen bowl alternative was substantially smaller than that of the filter, since the screen bowl was credited with a four to six percentage point decrease in product moisture compared to the disc. This comparison was made at ambient temperatures and reflected solely the mechanical dewatering capabilities of the two devices. No preheating of the feed was included in this particular comparison. Early generation screen bowl centrifuges operated under the principle of maximum bulk tonnage throughput. Second and third generation machines have followed the trends dictated by the coal industry calling for higher one-pass recoveries than previously demanded. The current generation of high-speed, long-bowl centrifuges permit recoveries of ultrafine solids directly comparable to commercial filter operation. On typical coal preparation plant feeds with nominal 600 E. an X 0 (28 mesh X 0) clean coal, recovery levels in excess of 99% are now obtained. The material that does escape the centrifuge and reports to the main effluent is typically -10 µm, high ash material. We have documented substantial beneficiation effects in screen bowl centrifuge performance with the cake product containing lower ash levels than the feed. On the referenced pipeline, coal tests performed on Western subbituminous coal, we found that the percentage of -10 µm material in the feed was six to eight times greater than normally encountered on eastern Appalachian seams. Our 45-t/h (50-stph) production centrifuge was never set up to maximize recovery. It was used as part of the two-stage dewatering circuit that had been chosen by designers of the proposed pipeline. Recoveries up to 95% were recorded. With field adjustments, that performance could most certainly have been improved. In contrast, manufacturers of the horizontal belt filter provided a small pilot-scale unit that operated on a side stream at the test facility. Numerous combinations of chemical additions were evaluated to determine those that had the best impact on filter performance. Whereas the screen bowl centrifuges operated without chemical addition, producing a dry, fluffy cake, the belt filter required two stages of chemical addition to attain satisfactory performance and high recovery levels. On the two-stage circuit that incorporated a belt press as the secondary

Jan 12, 1983

By John H. Hollomon

The interpretation of notched-bar impact results has been a matter of controversy since the introduction of more or less standard tests by Fremont,' Charpy2 and others at the turn of the century. Many investigators3-l1 have contributed to the understanding of the significance of such tests. Several symposiums12,13 have been held with the express purpose of discussing the significance and interpretation of the impact tests. It is not the purpose of this paper to review all these contributions to the development of the knowledge on this subject, but rather to present an interpretation of notched-bar impact tests that appears to be in agreement with the available published data. Fundamentally, the interpretation discussed in this paper of the brittle failure of some steels in notched-bar impact test is similar to the qualitative analysis presented by Ludwik3 in the I92o's. Essentially, Ludwik stated that the function of the notch was to increase the tensile stress necessary for yielding, and that brittle failure occurred when the stress necessary for yielding exceeded the normal stress required for fracture (with no plastic deformation). Ludwik, however, had no means of measuring this normal stress necessary for failure of a plastically* undeformed metal, therefore he could not extend his interpretation beyond the qualitative stage. Kuntze14 and recently Mc-Adam15 attempted to determine the effect of deformation on the stress necessary for fracture by testing, in tension, specimens notched to various depths and angles. Because of the uncertainties in Kuntze's (and McAdam's) analysis of the stresses (which have been pointed out by Sachs16) and the inherent nonuniformity in the stress distribution in notched bars, the results of such investigations are difficult to interpret. A more direct method of measuring the effect of deformation on the fracture stress was suggested in previous papers"-18 and has been utilized in the present investigation. The present paper concerns itself primarily with the behavior of notched impact specimens. The effects of strain rate, temperature, and stress distribution, which are discussed with reference to the impact specimen, apply just as well to the behavior of metal at the bases of notches in any engineering structure. All that is necessary is to determine the stress distribution in the structure at the base of the notches.

Jan 1, 1944

By G. Derge, Lo Ching Chang

The chemical and physical propertties of slag systems are of special interest to metallurgists, for nearly all metals are in contact with molten slags during the primary reduction from their ores and then during the subsequent refining and alloying processes that determine their ultimate use. These processes are carried out at high temperatures and involve such complex chemical systems that funda-mental scientific knowledge of the Properties and behavior of these slags is inadequate. Various hypotheses have been Proposed to explain known slag characteristics. The commonest of these regard the molten slag as constituted of compounds that are dissociated in varying degrees into their constituent oxides, as illustrated by Schenckl and the recent Papers of Chipman and co-authors. Another proposal is that these compounds dissociate by com-plete6 or partial ionization, the evidence for which has been reviewed by Martin and Derge.? whatever hypothesis is favored, the exact formulation of these compounds is incomplete. It is based on three principal types of information: 1. Studies of solidified 51% samples by X ray diffraction, petrography, and similar methods that can be used at room temperature. The correlation of this information with the high-temperature properties of the molten slag is uncertain. 2. Studies of slag-metal equilibria, which have the advantage of providing observations on the molten slag at high temperature. However, even these data present problems of interpretation because they require a complete knowledge of the metal phase. 3. Direct measurements of properties of molten slag at the temperature of greatest metallurgical interest. Viscosity, electrical conductivity, specific heats, and similar properties have been measured, but the data of this type are widely scattered and frequently difficult to interpret. Additional direct measurements of properties of molten slag that can be interpreted in terms of chemical behavior are required, and this paper shows that the standard physical-chemical measurement of reversible electrode potentials, which measure the activity of specific constituents, is a fruitful source of such information. The purpose of this investigation, therefore, was to find an electrode combination that would yield reversible electromotive force measurements when dipped into the molten slag to be studied. Slags of the systems cao-sio2 and cao-120,-SiO2 were chosen for study because graphite containers could be used and the data could be correlated with those for viscosity, conductivity, and other proper-

Jan 1, 1948

By D. J. McAdam

As shown in three recent papers by the author, in two papers by McAdam and Mebs, and in a paper by McAdam, Mebs, and Geil," the technical cohesive strength of a metal, in any particular state as regards mechanical treatment and heat-treatment, cannot be represented by a single stress value, but must be represented by a diagram with the principal stressest as coordinates. Each point on the boundary of such a diagram represents a technical cohesion limit. The technical cohesive strength thus comprises an infinite number of technical cohesion limits, each representing fracture under a specific stress combination. Moreover, neither the yield strength1 nor the ultimate strength can be represented completely by a single stress value, but must be represented by a diagram with the principal stresses as coordinates. All combinations of the principal stresses may be classified in three groups as illustrated by Fig. I. Fig. Ia shows three typical stress combinations with no two principal stresses equal. The magnitude of each principal stress is indicated qualitatively by the length of the arrow. Arrows pointing away from the cube indicate tensile stresses; arrows pointing toward the cube indicate compressive stresses. Typical stress combinations with two principal stresses equal are illustrated in Figs. rb and Ic. Such stress combinations would be produced by subjecting a cylinder to combinations of uniform axial and radial stresses. The uniform radial stress may be resolved into two equal principal stresses. with the mutually perpendicular directions rotatable around the axis of the cylinder. Fig. ib shows stress combinations with Sz equal to The greatest principal stress is in the axial direction, and the stress combination tends to cause either absolute or relative increase in length.* Fig. u shows stress combinations with S2 equal to St. The greatest principal stress is in the radial direction, and the combination tends to cause either absolute or relative decrease in length. The complete representation of either technical cohesive strength, yield strength, or ultimate strength generally requires a three-dimensional diagram. When two of the principal stresses are kept equal, however, the strength of a metal may be represented by a two-dimensional diagram with the coordinates representing the axial and radial stresses.6-II In this paper, attention will be confined almost entirely to stress combinations with two of the prin-

Jan 1, 1945

By G. R. C. Pacheco, D. M. Fonseca, R. Neuböck, G. E. Gonçalves, W. Moulin-Silva

Degradation by sulfur gases is an important lining wear mechanism in the copper industry. SO2/SO3 gases infiltrate into the pores of the basic refractory bricks, combine with their raw materials through expansive reactions and significantly modify the bricks’ structure. This study presents a comparison of the corrosion resistance against sulfur attack of different magnesia-based refractories using a simple, low-cost and quantitative method. Recipes containing sintered MgO grains showed lower resistance to corrosion by sulfur oxides compared to basic grades containing fused grains. Chromium corundum grades were used as a reference and showed very good resistance to this corrosion mechanism under the test conditions. The novel test provided relevant results that agree with what is commonly observed during operation and in previous post-mortem studies. This tool could be very useful in selecting refractory grades for the copper industry and predicting their performance. INTRODUCTION Oxidation of matte sulfides during copper production leads to the formation of sulfur oxides, which infiltrate into the pores of the refractory lining and react with the basic oxides below 1000°C to form magnesium and calcium sulfates. This reaction is accompanied by an expressive volume increase, consequent densification of the refractory microstructure and weakening of the brick bond (Malfliet et al., 2013). Thus, corrosion by SO2/SO3 is an important wear mechanism in the non-ferrous industry and the resistance to this compound should be considered when defining refractories for this application. Previous studies on this matter include expensive and complex testing methods involving pressurized SO2 gas cylinders in order to investigate the corrosion resistance of MgO-containing materials by sulfur oxides (Gerle & Podwórny et al., 2016; Fotoyi & Eric, 2011; Fotoyi, 2009; Podwórny & Piotrowski et al., 2008). The current study was based on a test developed by Pacheco & Fonseca (2018) to assess alkali infiltration and aims to provide an evaluation method of the corrosion resistance of refractories by SO2/SO3 in a simple and quantitative manner. This novel test is useful to compare the corrosion resistance of different refractory recipes and properly select the grades that should be employed in the non-ferrous industry. A case study is provided to illustrate the damage caused by sulfur oxides in refractory linings.

Jan 1, 2019

By Song Mao, Local Joint Engineering Lab of Efficient Util of Dominant Mineral Resources from Karst Regions, Guizhou Key Lab of Comprehensive Utilization of Non-metallic Mineral Resource, Xianhai Li, Qin Zhang, unjian Ye, Guizhou University, Wei Cheng, Zhihong Liu

"Phosphate tailing is a kind of industrial waste that emitted from separation processing of phosphate ores, which is usually discarged to the tailing pond without treatment. Recovery of phosphorus from tailings is of great significance for comprehensive utilization of phosphorus resource. Chemical composition of a micro-fine cryptocrystalline phosphate tailing was investigated by X Ray Fluorescence (XRF) and Inductively Coupled Plasma-Atomic Emission Spectrometry (ICP-AES), and mineral composition and occurrence of harmful elements were analyzed by optical microscope and Scanning Electron Microscope (SEM), X ray Energy Dispersive Spectrometer (X-ray EDS) and Mineral liberation Analyzer (MLA). On the basis of above, effects of those on mineral processing for phosphate tailing was analyzed. Chemical analysis results in combination with microscopy indicated that there is a certain amount of iron and aluminum and it should focus on the removal of them in separation processing. The cryptocrystalline structure, especially the micro banding structure and micro porphyritic structure indicated that there is quite amount of phosphate in fine particles and it should recovery the phosphorus as much as possible when designing the flotation technology for this difficult separation fine phosphate tailing. This study can provide theoretical guide for efficient phosphorus recovery of from fine phosphate tailing by flotation.INTRODUCTIONPhosphate rocks are vital nonrenewable resources and are essential components in agricultural fertilizers and phosphorous-based chemicals (Gharabaghi et al., 2009). About 95% of the phosphate produced around the world is consumed in the fertilizer industry (page 60 Abdel-Zaher, 2008; Jasinski, 2007). Froth flotation, a solid wettability based separation process is widely used in separation of phosphate rock and shown to be effective (Yehia et al., 1990; Singh et al., 1992; Elgillani and Abouzeid, 1993; Al-Fariss et al., 2013) .Poor selectivity and low recovery for micro-fine particles are hard issues in flotation of middle-low grade phosphate ore because Phosphate resources is becoming poor, fine and complex as the rich ores run out since the 1970s. The rapid depletion of high grade ores forces minerals industry to process low grade ores where finer grinding is required to achieve required liberation of the values, making the fine particle flotation inevitable. the performance of conventional flotation deteriorates rapidly as particle size decreases to below 10-20 µm, depending on the density of the particles (Feng and Aldrich, 1999). To date, fine particle flotation is still considered to be a challenge in mineral processing (Li et al., 2015) ."

Jan 1, 2016

By G. Derge

The chemical and physical propertties of slag systems are of special interest to metallurgists, for nearly all metals are in contact with molten slags during the primary reduction from their ores and then during the subsequent refining and alloying processes that determine their ultimate use. These processes are carried out at high temperatures and involve such complex chemical systems that funda-mental scientific knowledge of the Properties and behavior of these slags is inadequate. Various hypotheses have been Proposed to explain known slag characteristics. The commonest of these regard the molten slag as constituted of compounds that are dissociated in varying degrees into their constituent oxides, as illustrated by Schenckl and the recent Papers of Chipman and co-authors. Another proposal is that these compounds dissociate by com-plete6 or partial ionization, the evidence for which has been reviewed by Martin and Derge.? whatever hypothesis is favored, the exact formulation of these compounds is incomplete. It is based on three principal types of information: 1. Studies of solidified 51% samples by X ray diffraction, petrography, and similar methods that can be used at room temperature. The correlation of this information with the high-temperature properties of the molten slag is uncertain. 2. Studies of slag-metal equilibria, which have the advantage of providing observations on the molten slag at high temperature. However, even these data present problems of interpretation because they require a complete knowledge of the metal phase. 3. Direct measurements of properties of molten slag at the temperature of greatest metallurgical interest. Viscosity, electrical conductivity, specific heats, and similar properties have been measured, but the data of this type are widely scattered and frequently difficult to interpret. Additional direct measurements of properties of molten slag that can be interpreted in terms of chemical behavior are required, and this paper shows that the standard physical-chemical measurement of reversible electrode potentials, which measure the activity of specific constituents, is a fruitful source of such information. The purpose of this investigation, therefore, was to find an electrode combination that would yield reversible electromotive force measurements when dipped into the molten slag to be studied. Slags of the systems cao-sio2 and cao-120,-SiO2 were chosen for study because graphite containers could be used and the data could be correlated with those for viscosity, conductivity, and other proper-

Jan 1, 1948

By V. C. Allison

The explosibility of a dust is favored by its fineness and content of volatile combustible matter; its explosibility is decreased by its moisture and ash content. The explosibility of a dust can be reduced by admixture of either inert dust or water. The major effect of both the inert dust and water lies in their heat capacity; they absorb the heat of the explosion flame until the temperature of this flame drops below the ignition temperature of the explosive heat. The amount of inert dust necessary to make an explosive dust non-explosive can be calculated from its proximate analysis. FOREWORD LARGE-SCALE testing of the explosibility of coal dust as conducted by the Bureau of Mines in its Experimental Mine involves a large initial investment, and a high charge for maintenance and conduct of the test; in addition the work is necessarily slow because of the time required for the preparation of the tests and the cleaning and repairing of the mine after each test. These tests have been made along practical mining lines that admit of a range of mixtures of dust varying from 5 to 10 per cent. and with gas as low as 0.5 per cent. increments. Because of the time and expense involved, efforts have been made to devise a type of gallery for laboratory use in which the results obtained in the Experimental Mine may be correlated as an aid in a study of dusts, the explosibility of which might be approximately determined quickly and at a minimum of expense. The explosibility of coal dust has been studied by a number of European investors, using small laboratory devices; among these may be mentioned the experiments con¬ducted by Galloway, Vital, Hall and Clark, Abel, Mallard and Chatelier, Thorpe, Bedson and Widdas, Engler, Holwartz and Meyer, and Taffanel, results of whose experiments have been reviewed by the Bureau of Mines., The Bureau has conducted many tests with the Frazer-Clement2 apparatus, which gives the pressures set up when the dust cloud within is, ignited with a platinum coil or tube, heated to different temperatures, but for these tests the sample must be especially prepared as to size (200 mesh) and must be dry. An attempt has been made to design an apparatus that may be used for checking and correlating the experimental tests. The first design was a wooden gallery, 8 by

Jan 7, 1925

By Abram S. Hewitt

GENTLEMEN : If my first words were other than those of thanks for the high honor of being called to preside over the American Institute of Mining Engineers, I should do injustice alike to you and to my own sense of the obligation, under which I have been placed by your voluntary choice. When the position was first suggested to me, I resolutely declined to allow the use of my name, on the ground that, by training and occupation, I was not entitled to this honor, which, it then seemed to me, should be conferred only on a professional engineer. In fact, the history of the Institute, which had honored itself, as well as my distinguished predecessors, David Thomas, Rossiter W. Raymond, and Alexander L. Holley, by elevating them to its highest office, seemed to indicate the line and the limit of safe precedent, in which I did not then see how I could be included. But my scruples were finally removed by the consideration that, as in the course of human industry, the pioneer, of whom Mr. Thomas was so marked a type, must precede the mining engineer, so fitly personified in Dr. Raymond, and be followed by the mechanical engineer, whose incarnation we behold in Mr. Holley; so all these must be supplemented by the man of affairs and finance, in order that "enterprises of great pith and moment" may be prosecuted to a successful issue. I felt, therefore, that I had no longer any right to resist your preference, or to deprive myself of what I must regard as the crowning honor of an active career. On an occasion like the present it seems appropriate to review the history in this country, during the last hundred years, of those industries which the Institute of Mining Engineers specially represents. There is much in the story with which other members of this body are more familiarly acquainted than myself; yet I fancy that to all of them, and not less to our distinguished and most heartily welcome guests from abroad, a comprehensive outline of the progress of mining and metallurgy in the United States will prove interesting. I ask your attention, therefore, to a condensed account of that subject, embracing a statement of the beginnings of the industry on our shores, of the notable events attending its increase, and of its present

Jan 1, 1877

By John H. Hollomon

The interpretation of notched-bar impact results has been a matter of controversy since the introduction of more or less standard tests by Fremont,' Charpy2 and others at the turn of the century. Many investigators3-l1 have contributed to the understanding of the significance of such tests. Several symposiums12,13 have been held with the express purpose of discussing the significance and interpretation of the impact tests. It is not the purpose of this paper to review all these contributions to the development of the knowledge on this subject, but rather to present an interpretation of notched-bar impact tests that appears to be in agreement with the available published data. Fundamentally, the interpretation discussed in this paper of the brittle failure of some steels in notched-bar impact test is similar to the qualitative analysis presented by Ludwik3 in the I92o's. Essentially, Ludwik stated that the function of the notch was to increase the tensile stress necessary for yielding, and that brittle failure occurred when the stress necessary for yielding exceeded the normal stress required for fracture (with no plastic deformation). Ludwik, however, had no means of measuring this normal stress necessary for failure of a plastically* undeformed metal, therefore he could not extend his interpretation beyond the qualitative stage. Kuntze14 and recently Mc-Adam15 attempted to determine the effect of deformation on the stress necessary for fracture by testing, in tension, specimens notched to various depths and angles. Because of the uncertainties in Kuntze's (and McAdam's) analysis of the stresses (which have been pointed out by Sachs16) and the inherent nonuniformity in the stress distribution in notched bars, the results of such investigations are difficult to interpret. A more direct method of measuring the effect of deformation on the fracture stress was suggested in previous papers"-18 and has been utilized in the present investigation. The present paper concerns itself primarily with the behavior of notched impact specimens. The effects of strain rate, temperature, and stress distribution, which are discussed with reference to the impact specimen, apply just as well to the behavior of metal at the bases of notches in any engineering structure. All that is necessary is to determine the stress distribution in the structure at the base of the notches.

Jan 1, 1944

By Hon. Abrams S. Hewitt

Gentlemen : If my first words were other than those of thanks for the high honor of being called to preside over the American Institute of Mining Engineers, I should do injustice alike to you and to my own sense of the obligation, under which I have been placed by your voluntary choice. When the position was first suggested to me, I resolutely declined to allow the use of my name, on the ground that, by training and occopation, I was not entitled to this honor, which, it then seemed to me, should be conferred only on a professional engineer. In fact, the history of the Institute, which had honored itself, as well as my distinguished predecessors, David Thomas, Rossiter W. Raymond, and Alexander L. Holley, by elevating then] to its highest office, seemed to indicate the line and the limit of safe precedent, in which I did not then see how I could be included. But my scruples were finally removed by the consideration that, as in the course of human industry, the pioneer, of whom Mr. Thomas was so marked a type, must precede the mining engineer, so fitly personified in Dr. Raymond, and be followed by the mechanical engineer, whose incarnation we behold in Mr. Holley; so all these must be supplemented by the man of affairs and finance, in order that "enterprises of great pith and moment" may be prosecuted to a successful issue. I felt, therefore, that I had no longer any right to resist your preference, or to deprive myself of what I must regard as the crowning honor of an active career. On an occasion like the present it seems appropriate to review the history in this country, during the last hundred years, of those industries which the Institute of Mining Engineers specially represents. There is much in the story with which other members of this body are more familiarly acquainted than myself; yet I fancy that to all of them, and not less to our distinguished and most heartily welcome gnests from abroad, a comprehensive outline of the progress of mining and metallurgy in the United States mill prove interesting. I ask your attention, therefore, to a condensed account of that subject, embracing a statement of the beginnings of the industry on our shores, of the notable events attending its increase, and of its present

By John W. Cahn

The spinodal has long been regarded as a limit beyond which a homogeneous phase could no longer be metastable. But only recently has it become apparent that a phase beyond the spinodal would decompose by simple diffusional clustering mechanism quite different from the nucleation and growth mechanisms encountered for metastable phases. The theory of spinodal decomposition, which is based on the diffusion equation modified by thermodynamic requirements , is phenomenological, and each parameter can be measured by independent thermodynamic or diffusion experiments. The details of the theory have been carefully verified in a number of simple systems. It appears that the spinodal mechanism is commonly encountered in clustering reactions in solids and glasses. HISTORICAL INTRODUCTION The understanding of the earliest stages of precipitation in alloys has been the subject of three prior Institute of Metals Lectures. In 1932 Paul ~erica' reviewed the puzzling evidence that hardening of duralumin is completed before precipitation of CuAlz takes place and suggested that hardening occurs when the copper atoms "assemble in random groups on lattice positions of the duralumin, not of the CuAlz lattice". He called these random groups knots. This modification of his dispersion hardening theory seemed to fit all the facts, but Merica worried that the required diffusion "is just the reverse of what we deem normal; although quite spontaneous, it proceeds uphill, if you please". The reality of Merica's knots was quickly confirmed by Guinier's' and preston's3 X-ray work and these knots are today known as G.P. zones in their honor. Theoretical justification for uphill diffusion was also quickly provided by Becker and Dehlinger~ who noted that the diffusion coefficient could be negative in certain regions of phase diagrams. The boundaries of such regions could be described by a 90-year-old thermodynamic concept first described by ~ibbs' in 1877 as a limit of metastability for fluid phases, which by 1890 had received the name spinodal (see Appendix A). Spinodal in fluids is as old as nucleation theory. Both appear for the first time in the same paper by Gibbs who called the spinodal the limit of metastability. For the first 50 years, nucleation theory was forgotten and the spinodal was extensively treated in every good thermodynamics textbook.81Q The idea was simple and logical and it was accepted as part of a rigorous thermodynamic development of metastable phases, and for a while it was extensively investigated theoretically.

Jan 1, 1969

By Donald R. Rathburn, Jung K. Mok

An historical review and a survey of current practice in the application of fine dry grinding in the iron ore industry are given. Both closed and open-circuit applications are reviewed, and the advantages, disadvantages, and process considerations for these two systems are discussed. The ground ore temperature rise, and the cool-ing of ground ore and mill ventilation are also discussed, along with the agglomerating characteristics of dry ground ore. Screening during the production of high-grade lump ore for blast-furnace burden, particularly from recently developed ore deposits in Australia, South America, and Africa, has resulted in large tonnages of fine iron ore. Certain owners have decided to stockpile these fines until some later date. Others have either sold these fines "as is" for agglomeration at the steel plant or have established their own pelletizing plants to produce a premium quality agglomerate. In almost all cases some grinding is required prior to pelletizing. Most of these ores occur in the weathered state which may result in difficulty in the thickening and/or filtering stages when ground in a wet system. The resulting filter cake would probably require partial drying to provide a product suitable for the subsequent balling operation; however the partial drying and subsequent material-handling steps often produce random agglomeration. Normally, these agglomerates will cause problems in the green ball formation process. Thus dry grinding has developed as a solution to this problem. Most of the dry iron ore grinding installations utilizing the standard-type rod or ball mill are grinding high-grade natural ores that do not require beneficiation. Although power consumed per ton of final product is 120% or greater in dry grinding as compared with wet grinding, the additional power required for dewatering and handling a wet ground product can easily exceed the initial power savings. Dry grinding of raw feed and clinker has been practiced in the cement industry for many decades but its major application to the iron ore industry has taken place only within the past ten years. The successful application of dry grinding to iron ore has required the solution of several unique design and operating problems. The purpose of this paper is to review recent developments in fine dry grinding of iron ore for pelletizing and to discuss the various designs and operating parameters involved.

Jan 1, 1971

By Richard N. Hunt

Bingham has produced 6 per cent. of this country's copper. In total production, it ranks fourth among the copper camps of North America, the order being Butte, Michigan, Bisbee, and Bingham. In its annual production, it held that same rank until 1919, when its production was exceeded by the combined production of the Globe-Miami district of Arizona. Bingham has also been a lead camp of the first order. Utah ranks third among the lead-producing states, and its production comes largely from three camps which, in the order of their productivity, are: Bingham, Tintic, Park City. Bingham's silver production is important, but it does not rank high as a silver producer. Utah owes its rank as first among the silver-producing states to Tintic, a camp 40 miles due south of Bingham. The United States Mineral Resources reports a total production from Bingham for the period 1865-1920 having a gross value of $528,043,432. History of the Bingham District Bingham is on the eastern flank of the Oquirrh range 30 miles southwest of Salt Lake City, from which it can be reached in an hour by auto, or by the Denver & Rio Grande or the Bingham & Garfield railroads. The automobile route is a paved road across the floor of Great Salt Lake Valley, through farming country. The Bingham & Garfield railway leaves the level of Great Salt Lake at the northern end of the Oquirrh range, and in 20 miles it climbs 2100 ft., and deposits the traveler upon a shelf cut in the side of Bingham Canyon below most of the mines, which are farther up Bingham Canyon and its tributary Carr Fork. Below lies the town, a narrow ribbon running for a couple of miles along the bottom of a canyon 2000 ft. deep—an almost impossible site for a community numbering, in prosperous times, 5000 to 7000 inhabitants drawn from all quarters of the globe. Up the canyon and down, and beneath the steep slopes nearby, and beneath the town itself, are the mining operations of over half a century. During the past two decades one mine, the Utah Copper, has become so gigantic an operation as to dominate all other activity in the camp. It has become the greatest copper mine on the continent in production,

Jan 1, 1924

By Edward A. Capillon

The problem of scrap is probably of greater importance in the pro duction of gold, silver and other precious metal alloys than is the case for base metals and alloys. Remelting of gold and silver scrap in the shop is always a costly process because it involves losses by oxidation of thc base metals in the alloy with a consequent increase in the percentage of precious metal. This is most marked in the case of alloys containing the low-boiling and easily oxidized metals zinc and cadmium. Since it is not generally feasible to assay every shop remelt it follows that the possibilities of lost values arc large. So-called rolled gold and silver plate is made by soldering or welding the precious metal alloys onto base metal. Such plate when defective must be sent to the refinery to recover the gold and silver values, thereby involving additional expense in the form of refining charges. It is obvious therefore that gold and silver alloy scrap is an important item in manufacturing cost and must be reduced to a minimum. The amount of scrap resulting from poor metal will depend on a number of factors in the manufacturing operations, not least among which is the melting and casting practice. The notes which follow are a summary of experiments performed at various times to determine what variables in melting and casting are influential in the production of sound alloys. Metals Used in Alloying Pure gold, that is, gold of 24-kt. value is very much too soft for jewelry purposes and it is therefore always alloyed with other metals to increase its hardness and resistance to wear. For the same reason pure silver is seldom used alone but is alloyed with copper, the standard alloy being sterling silver which contains 92.5 per cent. silver and 7.5 per cent. copper. The metals commonly used for alloying gold are silver, coppcr, nickel and zinc. In addition to hardening the gold and producing alloys of different karat values the use of these metals makes possible the production of gold alloys of various colors such as yellow, red, green and white. The gold-silver-copper alloys vary in color from light greenish-white through green, yellow and red depending on the relative amounts of the three metals. Green or yellowish-green colored golds

Jan 1, 1930

By E.G. Lewis, l.M. Barker

The literature of milling is replete with papers devoted to the subject of ball milling, all of which no doubt have contributed in one way or another to progress in that art. In this paper reference will be made to only a few of the many authors, but the value of the contributions of all who have written on that subject is hereby acknowledged. With a few exceptions the efforts of most students of the subject have been devoted to laboratory investigations of principles. Davis1 was one of the first to report on plant-scale investigations and to present to mill men certain criteria for the guidance of ball-milling practices. His conclusions with respect to the significance of sizing analyses of classifier sands in their relation to the factors of mill speed and ball sizing are particularly referred to. Those conclusions were: 1. If the balls are large or the speed of the mill is high, crowding will appear at the finer sizes in the classifier sands. 2. If the balls are small or the speed is low, crowding will appear at the coarser sizes in the classifier sands. 3. The indications are that best efficiency is obtained when the screen analysis of the sands show a minimum crowding at any size. The last conclusion was qualified by the statement that it had not been proved conclusively. It is surprising, however, that the litera- ture of later years reveals little evidence that millmen have made any serious attempt to apply those criteria. This may, perhaps, be explained by the fact that the average plant-scale ball-milling problem presents so many variables that an investigation of any one of them encounters the problem of control of the others—a problem that often is unsurmountable in a small plant. In a large plant, in which there is a duplication of grinding units in parallel operation, opportunity may be afforded for determining the value of such criteria. Nevertheless, a study of published data from grinding circuits of both large and small plants suggests that either Davis' criteria have been tried and found inapplicable or have never been given consideration. For the purpose of testing Davis' conclusions and with improvement of ball-milling efficiency as the final objective, a test program was initiated in the concentrator of the New Cornelia branch of the Phelps Dodge Corporation early in 1938. The practices of that plant have already been described.2 The fine-grinding units are arranged so that any one of eight units may be operated as a test unit and its results compared with those of the remaining units. All units receive similar feed from a common storage bin, in which the product of the fine-crushing plant is bedded by traveling tripper. The ball mills are all similar in size and operated at the same speeds, and are individually metered. The feeder conveyors of each unit are equipped with Merrick weightometers. The test program as initially outlined proposed investigation of the following:

Jan 1, 1943

By J. D. Sullivan, Chester R. Austin, J. L. Nunes

It is characteristic of most shales and surface clays that a bloated or vesicular structure is produced by burning to a sufficiently high temperature, usually about 150° to 200°F. above the normal maturing temperature used when making common brick of the same material. Early investi-: gators recognized this phenomenon and attributed it to the release or expansion of gases in the vitrified piece. A number of theories have been advanced on the source of the gas and the manner in which it is evolved, but none has been proved conclusively. T. E. Jackson's1 early theory that bloating was due to oxygen evolved by ferric oxide in forming ferrous oxide or ferrous silicate was never substantiated by - experimental work. Orton2 thought this explanation unlikely, as all clays should bloat at the same temperature, if this were true. He found that clays bloated in the range from IIoo° to 17oo°C. Also, many clays containing iron did not bloat at all, but fused. Orton also stated that oxida- tion of different types of carbon was a source of gas during burning of clay and should be expelled before vitrification was reached. Seger3 said that he had dissolved ferric oxide in glass with no apparent evolution of gas. Matson4 came to the conclusion that ferruginous clays burned ' to vitrification in an oxidizing atmosphere did not have the iron in a ferrous form. According to Wilson,= the gases responsible for bloating might be entrapped air, water, sulphur dioxide, carbon monoxide, oxygen, and hydrocarbons. He spoke of two causes of bloating: (I) incomplete oxidation below the vitrification temperature, and (2) decomposition of compounds and evolution of gases above the vitrification temperature. Decomposition of calcium sulphate was given as the principal example of the latter. Bleininger and Montgomery0 stated that if any time after vitrification began the evolution of gaseous matter was rapid enough so that pressure was produced within the clay, bloating was certain to take place, and a vesicular structure would be formed. They recognized that initial structure, rate of heating, kiln atmosphere, and many other variables affected bloating. Work done by the Emergency Fleet Corporation7 indicated that clays suitable for bloating should be high in compounds of metallic oxides, carbon, sulphur, sodium, potassium, or other equivalent compounds, which either act as a flux or give off gas. Orton2 studied the chemical status of the carbon, iron, and sulphur in clays during various stages of burning, using a Huron shale that bloated under oxidizing or reducing conditions. He found that only a small amount of sulphur remained in the clay and that it could be detected only by dissolving the clay in hydrofluoric acid; i.e., the sulphur was in combination with the silica. orton said that this sulphur was probably in the form of iron sulphide dissolved in the glass phase. The iron sulphide was not broken down by heating, but was dissolved in the basic slag or glass,

Jan 1, 1942