Search Documents

By D. W. Lillie

It has been demonstrated that considerable bend ductility exists in bulk specimens of polycrystalline high-purity silicon. The possibility of hot-forming at 1200°C is suggested. EXCELLENT corrosion resistance in many media and low cross section for absorption of thermal neutrons (0.13 barn) would make silicon of interest to nuclear engineers were it not for extreme brittle-ness and the difficulty of fabrication by any reasonable means. The use of silicon for structural purposes also has been considered in view of its light weight and oxidation resistance. Johnson and Han-sen' have investigated the properties of silicon-base alloys and concluded that there was no way of making pure silicon or silicon-rich alloys ductile at room temperature. In view of reports of appreciable ductility in germanium single crystals above 550°C'." and some plastic deformation in single-crystal silicon above 900oC,' the present investigation was undertaken to define more precisely the limits of high-temperature ductility in pure silicon. After this investigation was begun torsion ductility in both germanium and silicon was reported by Greiner." Through the courtesy of F. H. Horn, a small bar of cast extra high-purity silicon was obtained and small bend specimens were made from it by careful machining and grinding. All of the reported tests results were obtained from samples from this bar (bar No. 1) and one other of similar source (bar No. 2). No complete analysis was obtained but, based on analysis of similar semi-conductor grade material, metallic impurities were under 0.01 pct total. Vacuum-fusion analysis for oxygen showed a value of 0.0018 2 0.0003 pct for the first bar tested and metallographic analysis showed no evidence of a second phase. Bend tests were carried out on an Instron tensile machine using a bend fixture with a 1 -in. span loaded at the center. Supporting and loading bars were 0.250 in. round and the load was applied by downward motion of the pulling crosshead of the machine. Specimen thickness and width were approximately 0.10 in. and % in. respectively. Loading rate was controlled by holding crosshead motion constant at 0.02 ipm. In some cases a smaller specimen was used on a 5/8-in. span with a 0.129-in.-diam loading bar. The entire bend fixture was surrounded by a hinged furnace and all heating was done in air atmosphere. Temperature measurement was made with thermocouples fastened directly to the bend fixture within less than 1 in. from the specimen. Autographic stress-strain curves were recorded during each test, and breaking load, total deflection, and plastic strain could be obtained from these curves. Stress was calculated from the beam formula S = 3PL/2bh2, where P is the load in pounds, L the span in inches, b the specimen width in inches, and h the specimen thickness in inches. This formula is strictly correct only in the elastic range but has been used to calculate a nominal stress for convenience in the plastic range. The stress given is the maximum stress in the specimen. Results The results of the complete series of tests are shown in Table I. The first group of tests (specimens Nos. 1-6) showed the beginning of plastic flow at a test temperature of 900°C, so two additional tests (Nos. 8 and 9) were made at 950°C on small-size specimens from bar No. 2. Specimen No. 8 was tested in the as-machined condition, and No. 9 was heat-treated in hydrogen at 1300°C for 2 hr, cooled to 1200°C and held 1 hr, cooled to 1000°C and held 1 hr, cooled to 900°C and held 1 hr, and finally cooled to a low temperature before removal from the hydrogen. It is apparent that the heat-treatment had a significant effect on yield strength and ductility. In addition, the magnitude of the yield point was conslderably reduced in the heat-treated specimen as is shown m Fig. 1 by tracings of the stress-strain curves. After obtaining a furnace capable of reaching higher temperatures specimens Nos. 10 to 13 were tested at 1100 and 1200°C. Strain rate was increased by up to a factor of 10 to see whether the ductility observed was excessively strain sensitive. Specimen NO. 10, strained at 0.02 ipm and 1100oC, was still bending at a deflection of 0.322 in. when the load rate was increased to 0.2 ipm, resulting in immediate

Jan 1, 1959

By Chas. A. R. Lambly

In the extreme northeast corner of the State of Washington, on the Canadian border, lies the Metaline mining district. This district is old in history, but young in production. Geology The Metaline district is a zinc-lead area of the replacement type in dolomite and limestone. The ore bodies of the Josephine horizon are in many ways similar to the ore bodies of the famous Tri-State zinc fields. The beds are faulted and folded and have varying low dips in varying directions, and underlie large areas of the district. History Production started in 1927 on a very limited basis. The property is now mining and milling 700 tons per day. The mine is opened by adit tunnels and a vertical shaft. As the ore horizons gained depth, it was necessary to sink inclines to follow the ore horizon (see Fig 1). From 1927 to date, approximately 600,000 ft of diamond drill was put down This work indicated that suficient tonnage existed to justify a redesigning of the whole operation, surface and underground. After four years of general study, the following program was planned: 1. A new mine entrance, which would be an incline, that could follow the ore body down at whatever pitch was necessary. The incline will be equipped with conveyors for the moving of ore and waste to the surface and with tractor-type locomotives for man and supply transportation. 2. The new incline also required a new type of mining which was developed and is now in use. It is called contour mining and will be described in a future paper. 3. The new incline exit would necessitate the moving of the mill and mine shops across the Pend Oreille River. This part of the program is now underway. The Incline The sinking of the incline was to start as soon as World War II ended and was as follows: The first leg of the incline was to be sunk from the surface 1600 ft on a 17" slope. The collar and first level at elevation 2180 ft, the second level at elevation 2000 ft, the third level at elevation 1875 ft, and the fourth level at elevation 1700 feet. From the 1700 ft elevation the incline was to flatten out to 12" for 400 ft to give the necessary depth for the ore pockets below the 1700 ft level and the necessary clearance for future sinking (see Fig 1 and 2). Due to lack of manpower in 1946, the program was changed and was as follows: A drift was driven from the old mine workings on the 1700 ft elevation in an easterly direction. At 1300 ft the drift was turned N 50" E and at this point a raise was driven 180 ft on a 50" slope. This raise intersected the Josephine horizon and commercial ore was encountered. At the 2000 ft mark, a main raise was driven, 245 ft on a 50" slope, and the 1875 ft elevation was cut. Exploration drifts were started on this level and production followed on a limited basis. The main drift at the 2500 ft point was turned N 35" E and ran parallel to and 10 ft east of and under the proposed incline line. At the proposed intersection of the drift and incline on the 1700 ft elevation, it was planned to raise the incline to intersect the 245 ft raise and to continue on to the surface, a distance of 1600 ft. When this proposed intersection point was reached, a heavy flow of water, approximately 800 gpm, was encountered and all work on the main drift face was stopped. This water flow flooded the main pump station in the old mine and the two lower levels with approximately 20,000,000 gal of water. The water was controlled and finally drained from the cave areas and lower levels after six months of pumping. After the heavy flow of water was encountered in the main heading, it was decided that the incline would have to be started from the surface, as originally planned, so that too much time would not be lost. The surface overburden had to be removed, a total of 6000 yards. A temporary dry house for 6 men was built. An 8 in. churn drill hole was intersected in the first raise driven from the 1700 foot elevation tunnel. Air and water lines were placed in this hole, and air and water were delivered to the collar of the incline from the mine working. The incline started down at 15 ft wide and 7 ft high through the Leadbetter slates. After sinking 4 sets, it was

Jan 1, 1950

By R. O. Williams

Analytical representation of the thermodynamics of solutions is highly desirable from the standpoint of accuracy, compactness, and numerical manipulations. In particular, computer calculations are greatly implemented. Mathematical considerations show that previous expressions have one or more serious defects. This investigation shows a Fourier series to be satisfactory but that it is also possible to derive a new series which fits certain additional conditions. Included examples show the value of analytical expressions in giving a simple characterization of each system using some two to five parameters, the elimination of the Gibbs-Duhem integration, and the es timation of the error for the experimental function as well as derived functions. It is further shown that the present characterization provides easy comparison between systems. IN the past, thermodynamic calculations have depended to a considerable extent on tabular and graphical methods. As the volume and precision of such data increase such methods become less satisfactory. Specifically, the selection of the optimum representation and the estimation of errors require statistical methods which in turn require analytical representation. The utilization of such data require further manipulations which are best done analytically for maximum precision. For example, phase equilibria are determined by common tangents to free-energy curves: a graphical determination is normally of low accuracy. As computers are increasingly used analytical representations become almost mandatory. Insufficient mathematical consideration has been given previously to the selection of empirical expressions. Those expressions having some theoretical justification are generally too inflexible and mathematically unattractive. We consider the problem in some detail and show that a Fourier series can be effectively used. Also a new series is defined which has certain advantages. ANALYSIS We wish to consider the analytical representation of the heat of mixing, AH, the excess free energy, ?Gxs, and the excess entropy, ?sXS, as a function of composition, X, for binary solutions relative to the pure components in the same state. When a distinction is not required, we use W to denote any one of the above functions. One may use a Taylor expansion around X = 0 to generate a power series. As the derivatives are un- known we represent the series as W = A + BX + CX2 + DX3 + EX4 + ... [l] where the constants A , B, C , ..- are to be selected to provide some optimum fit. For the extremes of composition W is necessarily zero so it follows that A = 0 [2a] B +C + D + E +••• = 0 [2b] Nonelectrolytes, which we are considering, appear to satisfy the condition that d3W/dx3 = 0 [3] in the terminal regions. This is the basis of the a, ß, and Q functions used by Hultgren et al.' and others. While this condition does not have a strong theoretical basis it does appear desirable that any analytical relation should satisfy this condition. Darken2 and Turk-dogan and Darken3 have shown that many systems exhibit this behavior over an extended range from each terminal region, departure being restricted to a limited intermediate region. Since we have no a priori knowledge as to where this transition occurs we can require that this condition be satisfied only as a limit at the extreme compositions as a general condition. We will show later how more restricted conditions can be included in specific solutions. Darken2 has called this behavior the quadratic formalism; we call our application the limiting quadratic formalism, LQF. This condition applied to the above power series requires that D = 0 [4a] 4-3-2E +5-4-3_F + 6 • 5 . 4G + ••• =0 [4b] The form of the power series normally used, due to Margules,4 is W=X(1-X)(A + BX + CX2 + DX3 + EX4 + •••) [5] where A, B, C, --. are a new set of constants. (Guggenheim5 has given a variation of this expression in a more desirable form. Since, however, it is contained in the above expression it does not require separate consideration.) This form is precisely what results by incorporating the conditions in Eq. [2] into the power series and regrouping the constants. The LQF requires that B =C [6a] and 4.3.2(D-C) +5-4-3(E-D) + ••• =0 [6b] Thus, the correct form of the Margules expression with two adjustable parameters is w =X(1-X)[A + B +X2-2/3x3)] 171 and the EX4 term must be included before three adjustable parameters are permitted.

Jan 1, 1970

By Shiou-Chuan Sun

THIS paper presents the design and operation of a frothmeter capable of measuring the frothing characteristics of pine oils and other frothing reagents. The experimental data show that the froth-ability of pine oil is governed by: 1—rate of aeration, 2—time of aeration, 3—height of liquid column, 4—chemical composition of pine oil, 5—pH value of solution, 6—temperature of solution, and 7—concentration of pine oil in solution. The effect of mineral particles on the behavior of froth also was studied, and the results can be found in a separate paper.' The results also show that the relative froth-abilities of pine oils in the frothmeter generally correlate with those in actual flotation, provided that other factors are kept constant. In addition to pine oils, the other well-established flotation frothers were tested, and the results are included. In this paper, compressed air frothing is the frothing process performed by means of purified compressed air, whereas sucked air frothing is the frothing process accomplished by purified air sucked into the glass cylinder by a vacuum system. The term vacuum frothing denotes that froth was formed by degassing of the air-saturated liquid under a closed vacuum system. Apparatus The frothmeter, shown in Fig. 1, is capable of re-producibly measuring the volume and persistence of froth as well as the volume of air bubbles entrapped in the liquid and is capable of being used for compressed air frothing, sucked air frothing, and vacuum frothing. Fig. la shows that for compressed air frothing, the apparatus consists of an airflow regulating system, 1-3; a purifying and drying system, 4-8; a standardized flowmeter to measure the rate of airflow from zero to 500 cc per sec, 9; and a graduated glass cylinder, 13; equipped with an air regulating stopcock, 10; an air chamber, 11; and a fritted glass disk to produce froth, 12. The fritted glass disk, 5 cm in diam and 0.3 cm thick, has an average pore diameter of 85 to 145 microns. The pyrex glass cylinder has a uniform ID of 5.588 cm and an effective height of 63 cm. The inside cross-sectional area of the glass cylinder was calculated to be 24.53 sq cm, or 3.8 sq in. For sucked air frothing, Fig. lb shows that the apparatus for compressed air frothing is used again, with the following modifications: 1—compressed air and its regulating system, 1-3, are eliminated; and 2—a vacuum system, 16, equipped with a vapor trap, 15, and a vacuum manometer, 17, is added. The vacuum system can be either a water aspirator or a laboratory vacuum pump. Any desired rate of airflow can be drawn into the glass cylinder, 13, by adjusting the opening of the air regulating stopcock, 10. The sucked air stream is cleaned by the purifying and drying system, 4-8, before entering the glass cylinder, 13. When this setup is used for vacuum frothing, the air regulating stopcock is closed. The frothmeter has been used for almost 3 years and has proved to give reproducible results, as illustrated in Table I. With a magnifying glass and suitable illumination, the frothmeter also can be used to study the attachment of air bubbles to coarse mineral particles.' Experimental Procedures Except where otherwise stated, the data presented were established by means of the compressed air method. The volume and persistence of froth were recorded respectively at the end of 4 and 6 min of aeration at a constant rate of airflow of 29.3 cc per sec, which is equivalent to 71.6 cc per sq cm per min, or 462.6 cc per sq in. per min. The aqueous solution for each test, containing 1000 cc of distilled water and 19.2 ± 0.5 mg frothing reagent, was adjusted to a pH of 6.9 0.2. The volume of froth is expressed as cubic centimeter per square centimeter and is equivalent to the height of the froth column (the distance between the bottom and the meniscus of the froth). The volume of froth was obtained by multiplying the height of froth by the cross-sectional area of the glass cylinder, 24.53 sq cm. Before each test, the glass cylinder, 13, was cleaned thoroughly with jets of tap water, ethyl alcohol, tap water, cleaning solution, tap water, and finally distilled water. The cylinder with stopcock,

Jan 1, 1953

By E. F. Thomas

THE late George S. Rice was active in the inves--I- tigation of bumps, particularly in the last ten years of his career as chief mining engineer of the U. S. Bureau of Mines. Since most of his investigation was carried out in Great Britain, continental Europe, and—to a lesser extent—Canada, his thinking on prevention was influenced considerably by the experience of those countries. It is not surprising, therefore, that when he was called upon a few years before his retirement to investigate bumps in the U. S. and suggest ways to prevent them, he turned to longwall mining. A longwall method had been most successful in combating the bump hazard in mining coal under deep cover, especially in Great Britain, but the prevailing method there at the time was advancing longwall mining, which he knew was uneconomical under U. S. mining conditions. For this reason he proposed a modified retreating longwall system that he believed included the best features of the advancing method. As brought out by Rice,' if the cover is 2000 ft and 50 pct of the coal is extracted, the static load on the remaining pillars will be about 4000 psi, which exceeds the ultimate crushing strength in most instances. If the pillar coal is overloaded before a pillar line is established, then the abutment zone preceding a line of extraction is no place to split pillars or extract them by any method other than an open-end system. Rice therefore advocated open-end mining, preferably by longwall, but he was willing to compromise with long-face mining if the longwall method was not acceptable. Rice's system was put into operation in a mine in Harlan County, Kentucky,3 but subsequent experience has shown that it did not take into account two important factors—avoidance of pillar-line points and maintenance of adequate development in advance of the pillar-line abutment area. For ten years after Rice's retirement the USBM did little investigation and research on bumps, chiefly because so few were occurring that there was not much cause for alarm. But in 1951 there were three occurrences involving fatal injuries, and the Bureau began a statistical survey in that year. C. T. Holland, head of the department of mines at Virginia Polytechnic Institute, was retained as a consultant. The resulting study' of 117 case histories brought out these important conclusions: 1) Almost invariably the bump occurred in a locality affected by the abutment zones of one or more pillar lines. 2) In most cases the locality of the bump was influenced by the abutment zones of more than one pillar line. The term pillar-line point has been used for many years in the Appalachian region for such a situation. Point is used in the geographical rather than the mathematical sense. 3) In pillar-line extraction the following practices are safest in preventing bumps: a. The mine layout should provide for pillars of uniform size and shape along the extraction line. b. The mine layout should be planned so that no development need be done in the abutment zone of a pillar line. c. The layout should permit open-end extraction of pillar lines from the next goaf, so that it will not be necessary to resort to pocket mining, splitting pillars, or any practice that will involve driving in the direction of the goaf within the abutment zone. d. Pillars should be large enough to support area without undue roof and floor convergence before establishment of a pillar line. These are, of course, generalities, and while they are useful in laying out areas where bumps can be expected, they are of limited help in many mines that were committed to a system of mining before it was realized that they were subject to bumps. Under such conditions it becomes necessary to choose between the following alternatives: 1) Abandon the territory, except for pillars that offer no extraction problems. 2) Through experience select the pillars that are most heavily loaded, and, by augering, induce bumps from a safe vantage point so that impinged loads are relieved. This method was first developed at the Gary, W. Va. mines of U. S. Steel Corp. and later adapted to mining thick coal beds at Kaiser Steel's Sunnyside mine in Utah. No scientific method is available to determine where to drill within a loaded pillar. Although this method of unloading has worked very successfully at Gary—with one exception—

Jan 1, 1959

By E. Kendall Cork

The traditional financial objective for a single mine company has been to operate as frugally as possible and to pay out most of the earnings as dividends. If the business is cyclical (as it is for most metals) the dividends might fluctuate quite widely. When the mine is exhausted the company disappears. This is still quite a viable strategy for a single mine company. It is not however a viable strategy for the world as a whole. The mining industry is built by mine development companies who can mobilize the people and capital to bring new mines into production. Their skills must include marketing, engineering, finance and other politics. It is very rare for a property to be brought in without the support of a major company that can provide all these services. The exceptions will usually have some other form of big brother support, for example the U.S. government uranium contracts at guaranteed generous prices. The mine development company will seek as a minimum to perpetuate itself by developing new mines in order to replace those which are running out. The more common and more ambitious objective is to grow -- that is to add to its ore reserves and current production by developing more new mines. The financial objectives for that company are very different. Obviously if all the earnings were paid out in dividends there would be nothing left to work with. The first financial policy then is to spend an appropriate amount on exploration for new properties. The next is to retain enough of the earnings to provide the capital for new projects at least sufficient for the equity. There is no magic formula as to what proportion of earnings should properly be distributed as dividends by a growth-oriented mine development company. As a rough rule of thumb distributing half or more will probably leave too little to work on and 30% or so is probably a good balance. However the circumstances differ widely from company to company. It may be useful to set an objective for the rate of growth of a company's earnings. Some have picked rates such as 15% per annum compounded. Others have set a target in real terms which might appear as 10 or 11% plus inflation. Obviously the arithmetic of compound interest is very attractive; however in practice there is much variation. Indeed current returns from existing operations swing widely with the business cycle and there is no assurance that economic new properties will be found according to someone's arbitrary time schedule. For example, Western Mining Corporation Limited in Australia explored for 30 years with little to show for it, but then found the great Australian nickel deposits and more recently the huge Roxby Downs copper. That long dry spell could not have fitted anyone's arbitrary calendar of growth and yet they would not have found such orebodies without that long period of effort. Should they have abandoned the search? Once a new property has been found or acquired there has to be a threshold rate of return on the new capital to be invested against which to evaluate the property's economics. Conventionally this seems to be 15% after tax, a number common in other heavy industries as well. In some cases it is expressed as a lower number plus allowance for inflation. Discounted cash flow analysis is a very useful tool but it does not make the decision. In the end a "go" decision depends on judgment of many factors some of which are numbers used in the DCF calculation whose credibility must be examined. It is curious how frequently investment proposals come in with the rates of return very close to 15%. The project advocates know that a number much less than 15% will not fly and that a number much more is not necessary. With much higher nominal and real interest rates of recent years, even though before tax, logic suggests that the hurdle rate should also rise. The power of compound interest is so great that 20% is very hard to achieve in any cash flow projection but 18% may be a sensible yard - stick. Once again it is remarkable how many project proposals come in with an 18% return. On the record the mining industry as a whole has not been overly restrictive in choosing its hurdle rates of return. This is shown by the abundance of metals in recent years and the failure of metal prices to keep up with inflation. All of the foregoing is standard text book stuff.

Jan 1, 1985

By R. A. Garling

INTRODUCTION Since the infancy of in situ uranium mining, a growing number of hydrometallurgical processes have been incorporated into pilot and commercial scale flowsheets. Although initial design efforts were geared toward maximizing uranium recovery and minimizing plant and wellfield flow circuit maintenance, recent emphasis has shifted to improved means of water conservation and aquifer restoration. As mining units approached depletion, evaporation ponds reached minimum freeboard, and state and federal agencies demanded proof of groundwater restoration, processes including mixed bed and conventional ion exchange, reverse osmosis and electrodialysis were adopted by the industry. These units served the additional function of reducing process bleed flows during mining in states where the deep disposal well permitting ice remains unbroken. This report concerns the use of electrodialysis as an alternative to the more conventional processes used in in situ mining. In addition to a brief history and description of the process, a comparison to reverse osmosis and operational data derived from testing an Ionics, Inc. 1.31 x 10-3 m /s (30,000 gallon/day) unit at the Teton-Nedco Leuenberger Research and Development pilot will be presented. HISTORY Commercially practicable electrodialysis was contingent upon the development of synthetic ion exchange membranes in 1940's. In 1952, Ionics Inc. demonstrated that the process was amenable to the treatment of salt and brackish water and, in 1954, made their first commercial sale. The following decade saw several major electrodialysis unit sales which were generally targeted for use on private or municipal potable water treatment. Major increases in membrane desalting unit capacities, facilitated by technological advances in the reserve osmosis industry, were noted during the 1970's. The development of polarity reversing electrodialysis equipment which reduced feed pretreatment requirements, increased water recovery rates, and simplified unit operation, kept Ionics Inc. competetive in the water treatment industry. Engineering advances which incorporated automated equipment, non-corrosive construction materials, and improved ion exchange membranes allowed the electrodialysis process to compete in industrial waste treatment among other commercial markets. PROCESS AND APPARATUS DESCRIPTION The electrodialysis process utilizes direct electrical current passed across a stack of alternating cation and anion selective membranes in order to achieve an electrochemical separation of ionized materials in an aqueous solution. The membrane stack has the appearance of a plate and frame filter press and auxilliary equipment includes solution pumps, electrically actuated valves, filters, piping and a direct current power source. The ion separation membranes are thin sheets of synthetic cation or anion selective resins. Attaching sulfonate or quaternary ammonium groups to the cross linked copolymer structure determines the ion selectivity of the membrane. The membranes are separated from each other in the stack by non-conductive spacers that house flow channels which route the flow tortuously and parallel to the membranes. Direct electrical current passing perpendicularly to the membranes and solution passages attracts cations toward the cathode and anions toward the anode (Figure 1). As the ions from the feed stream pass through the ion selective membranes, they become concentrated in the adjacent brine channel and are retained there by the combined attractive force of the electrode and the repelling force of the next membrane toward the electrode. Limiting factors on the degree of demineralization possible include chemical solubilities in the brine flow and the current density that will produce an unacceptable degree of polarization (Figure 1). Feed or brine solution treatment with complexing agents or acids has been successfully applied to prevent membrane scaling. Polarization can occur when sufficient current density is applied to dissociate water in the ion depleted region of the diluting compartments near the membrane surfaces. Significant polarization is evidenced by large electrical resistances across cell pairs and notable pH differences between diluting and concentrating streams. Limiting current densities have been increased in U.S. manufactured equipment by utilizing tortuous flow paths of relatively high linear velocities thereby promoting continous solution mixing. Energy consumption is due to separating electrolytes and solutions, oxidation and reduction reactions occurring in electrode compartments, overcoming electrical resistance, conversion from AC to DC power, solution pumping and auxiliary equipment actuation. A major improvement to the basic electrodialysis process was applied in 1970 which resulted in frequent, automatic cleaning and descaling of membrane surfaces. The process, polarity reversal, incorporates alternating the cathode and anode on a periodic basis while exchanging product and brine flow channels via electrically actuated values. The reversal reduces the potential of stack plugging with CaCO3 (calcite), CaSO4 (gypsum), and colloidal materials and, in most waters, eliminates feed pre-treatment requirements. For approximately two minutes during and following the reversal, off spec. water is flushed to waste or reintroduced to the feed supply. The usual feed treatment on polarity reversing electro-

Jan 1, 1982

By Glenn S. Wyman

CHUQUICAMATA, located in northern Chile in the Province of Antofagasta, is on the western slope of the Andes at an elevation of 9500 ft. Because of its position on the eastern edge of the Atacama Desert, the climate is extremely arid with practically no precipitation, either rain or snow. All primary blasting in the open-pit mine at Chuquicamata is done by the churn drill, blasthole method. Since 1915; when the first tonnages of importance were removed from the open pit, there have been many changes in the blasting practice, but no clear-cut rules of method and procedure have been devised for application to the mine as a whole. One general fact stands out: both the ore and waste rock at Chuquicamata are difficult to break satisfactorily for the most efficient operation of power shovels. Numerous experiments have been made in an effort to improve the breakage and thereby increase the shovel efficiency. Holes of different diameter have been drilled, the length of toe and spacing of holes have been varied, and several types of explosives have been used. Early blasting was done by the tunnel method. The banks were high, generally 30 m, requiring the use of large charges of black powder, detonated by electric blasting caps: Large tonnages were broken at comparatively low cost, but the method left such a large proportion of oversize material for secondary blasting that satisfactory shovel operation was practically impossible: Railroad-type steam and electric shovels then in service proved unequal to the task of efficiently handling the large proportion of oversize material produced. The clean-up of high banks proved to be dangerous and expensive as large quantities of explosive were consumed in dressing these banks, and from time to time the shovels were damaged by rock slides. As early as 1923 the high benches were divided, and a standard height of 12 m was selected for the development of new benches. The recently acquired Bucyrus-Erie 550-B shovel, with its greater radius of operation compared to the Bucyrus-Erie 320-B formerly used for bench development, allowed the bench height to be increased to 16 m. Churn drill, blasthole shooting proved to be successful, and tunnel blasts were limited to certain locations where development existed or natural ground conditions made the method more attractive than the use of churn-drill holes. Liquid oxygen explosive and black powder were used along with dynamite of various grades in blasthole loading up to early 1937. Liquid oxygen and black powder were discontinued because they were more difficult to handle due to their sensitivity to fire or sparks in the extremely dry climate. At present ammonium nitrate dynamite is favored because of its superior handling qualities and its adaptability to the dry condition found in 90 pct of the mine. In wet holes, which are found only in the lowest bench of the pit and account for the remaining 10 pct of the ground to be broken, Nitramon in 8x24-in. cans, or ammonium nitrate dynamite packed in 8x24-in. paper cartridges, is being used. This latter explosive, which is protected by a special antiwetting agent that makes the cartridges resistant to water for about 24 hr, currently is considered the best available for the work and is preferred over Nitramon. Early churn drill hole shots detonated' by electric blasting caps, one in each hole, gave trouble because of misfires caused by the improper balance of resistance in the electrical circuits. Primarily, it was of vital importance to effect an absolute balance of resistance in these circuits, the undertaking and completion of which invariably caused delays in the shooting schedule. Misfires resulting from the improper balance of electrical circuits, or from any other cause, were extremely hazardous, since holes had to be unloaded or fired by the insertion of another detonator. The advent of cordeau, later followed by primacord, corrected this particular difficulty and therefore reduced the possibility of missed holes. After much experimentation, the blasting practice evolved into single row, multihole shots, with the holes spaced 4.5 to 5 m center to center in a row 7.5 to 8 m back from the toe. Such shots were fired from either end .by electric blasting caps attached to the main trunk lines of cordeau or primacord. The detonating speed of cordeau or primacord gave the practical effect of firing all holes instantaneously. Double row and multirow blasts, fired instantaneously with cordeau or primacord, proved to be unsatisfactory in the type of rock found at Chuquica-

Jan 1, 1952

By Victor deWolfe

INTRODUCTION The Henderson Mine, located near Empire, Colorado, utilizes a continuous panel caving system to extract ore as one of the world's major producers of molybdenum. Any mine using a caving-by-gravity technique of mining must rely on closely controlled draw of the caved ore. This control is essential to insure proper caving action, to avoid damaging load concentrations of weight and to minimize the dilution of ore with waste material. Henderson is no exception. Draw control is a major factor in all production planning, from long- range plans to short-range and day-to-day ore scheduling. Draw control is reviewed constantly and administered daily in an effort to optimize production efficiency, ore recovery, and cave management. MINING METHOD The cave at Henderson is massive, moving slowly through large panels that are 244 m (800 ft.) wide by 610 m (2,000 ft.) long. Generally two cave areas are drawn at one time. The areas under active draw vary in size but can be as large as 244 m (800 ft.) by 244 m (800 ft. ) containing 400 draw points. Each draw point contains 45,360 mt (50,000 st) on the average and takes about two and one half years to exhaust. A complete panel is worked for seven to ten years. No pillar exists between panels, but rather a buffer zone of broken ore, or "static face," is left in each panel to be drawn with the adjacent, yet-to-be-caved panel in efforts of minimizing dilution of a working area from an exhausted one. (Figure 1) Production drifts are driven on 24.4 m (80 ft.) centers through the ore body. Between the production drifts are funnel-shaped draw bells on 12.2 m (40 ft.) x 24.4 m (80 ft.) centers to receive ore from the cave. Each bell is accessed by two draw points, one from the production drift on either side, thus forming a 12.2 m (40 ft.) x 12.2 m (40 ft.) draw pattern. Extraction of the ore is by rubber-tired, 3.8 m3 (5 yd3) load-haul-dump equipment. The LHDs then tram the ore a maximum of 49 m (160 ft.) to ore passes. Cave initiation and bell development are done from the undercut drifts which are parallel to and 17 m (55 ft.) directly above the production drifts. Longhole rings are drilled and blasted from the undercut drifts to define the bells and establish the undercut for caving. (Figure 2) DRAW CONTROL Since the cave line at Henderson is constantly advancing, it is necessary to be continually initiating new cave at one end while exhausting it at the opposite end. There must exist, therefore, an angle on the ore-waste contact in the broken rock from initiation to exhaustion. The basic concept of draw control is to keep this angle as smooth and even as possible, particularly at the time of exhaustion. If this is achieved, draw points are exhausted more or less in a line, avoiding pockets of remaining ore surrounded by exhausted areas. These pockets would cause spotty ore extraction at the time of exhaustion, increasing the amount of dilution occurring while introducing the potential for significant weight problems in the production area. To arrive at the desired angle on the ore- waste contact, maximum tonnage percentages are assigned to each row of draw points increasing at 10% or 15% increments (depending on cave size and velocity of draw) working away from the cave line. The available tonnage indicated by these percentages is the maximum allowable tonnage to be extracted from each draw point until the available tonnage percent- age is increased. As the cave moves, these percentages increase for each draw point regularly. However, in general the tonnage drawn from each draw point is kept at about 50% of this allowable maximum in order to maintain adequate available tonnage in the cave to sustain production for seven months if cave initiation were to cease. This available tonnage cushion is a safeguard built into the draw control program at Henderson to accommodate fluctuations in the rate of cave advance. When draw points move past the row of 100% tonnage availability, they are drawn past the desired 50% at the same increments per row until exhausted. (Figure 3) To achieve proper draw control, the number of LHD buckets to be taken from each draw point is assigned daily. The actual buckets taken, which may at times deviate from the

Jan 1, 1981

By J. D. Cooper, D. W. Thompson, J. Basiuk, W. Cass, R. Ilves

The Department of Thoracic Surgery and Pathology at the Toronto General Hospital have had a long standing interest in the early detection and treatment of carcinoma of the lung. Our initial experience was with a population at risk due to a prolonged period of cigarette smoking. More recently our efforts have turned to industrial exposure, specifically in the nickel and uranium industries. [Initial Screening Project] (1) For a three year period 1963 to 1966 a cytology screening program was carried out through the Out-Patient Department. The study was limited to cigarette smokers over 40 in age. A total of 1586 patients were examined. Of the sputa collected, the classification is seen in Table 1. There were 11 malignant sputa present. Added to this number were 25 patients with symptoms, normal chest X-rays, but malignant cells on cytology, and a further 5 patients in whom an abnormality (eventually proven non-malignant) showed on X-ray, and sputum showed malignancy which was radio logically occult. (Table II). This gave a total of 41 patients with malignant sputum who were evaluated between 1960 and 1966. The clinical course of these patients is seen in Table III. Only 19 of 41 patients had localization and treatment of their tumour during that study period and this low rate of localization attests to the technical difficulties endoscopy in that day presented. The method of localization was as follows: a) 6 patients showed an area of segmental pneumonitis somewhere in this time period b) Using the rigid bronchoscope localized the tumour in 9. This was proven by direct biopsy, and frequently required more than one bronchoscopy over a prolonged time period. c) bronchograms and tomograms showed abnormalities in 5 patients. Of these 19 patients, 5 were treated by radiotherapy because of general condition or refusal of surgery. Three of the irradiated patients died of recurrent cancer within three years. The other two died within one year of unrelated disease. Fourteen patients underwent resection, with one operative mortality. At pathology, the tumours were "in situ" in 6 and invasive in 13. There was no evidence of nodal spread. When last followed up in 1979, there were no cases of recurrent tumour and no cases of second lung primary tumours. Similar experiences have been reported from the Mayo Clinic (2), Johns Hopkins (3) and Memorial Hospitals (4). Early detection of radiologically occult tumours which are in situ or minimally invasive has given uniformly good results. There have been no deaths from recurrent or metastatic cancer in surgically resected patients, and only one second primary tumour has been detected. Interestingly, the Hopkins group reports that 5 patients with Stage I squamous cell tumours refused operation. One refused any treatment and died of disease at 12 months. Three were radiated, and were alive from 14-38 months post-treatment, all with evidence of recurrent disease. [Sudbury Sintering Plant Study](5) From 1948 to 1963 an open travelling-grate sintering process was employed to convert nickel sulfide to nickel oxide at an International Nickel Company operation. The environment in this plant was particularly dusty and filled with fumes. It became apparent by 1969 that the incidence of bronchogenic carcinoma was markedly increased in workers from this plant. A concerted effort was made to track down all workmen with this exposure. During 1973 and 1974, 268 men were studied. Chest radiographs were done and showed no mass lesions. Sputum was collected on three consecutive days and analyzed. There were 12 men with malignant sputum, all of the squamous cell variety. Two refused any investigation, one presenting 31/2 years later with extensive hronchogenic carcinoma, and the other 5 years later with extensive carcinoma of the maxillary sinus. In the remaining ten patients careful rhinolaryngeal examination as well as a detailed bronchoscopy, involving examination, brushings and biopsy of all pulmonary segments was carried out. One patient was found to have laryngeal carcinoma and was treated by radiation. In nine patients, the malignancy was localized to the lung, leading to six lobectomies, two pneumonectomies and one sleeve lobectomy at operation. However, the follow-up in these cases suggests a different biological behaviour with these industrially related tumours. While no tumour has recurred locally, one patient has died of metastatic cancer and two patients have developed second and one patient a third pulmonary primary cancer. However, survival has still been much better than wits radiographically manifest lung cancer. [Technique of Localization] (6) Following a careful rhinolaryngeal examina examined and then the lower respiratory tract is examined. This is all performed under general anaesthesia. The trachea is examined with the rigid Jackson bronchoscope, collect-

Jan 1, 1981

MR. HARRINGTON: I would like to ask Mr. Bottomley if they fire their shots while the men are in the mine? MR. BOTTOMLEY: No sir; the shot-firing law in our State requires the shots to be fired after the men are out of the mine. We fire more shots than we did under the hand method of loading. Where formerly four holes were drilled, now we drill eight, using the same amount of powder as we did formerly, perhaps a little more, but we use a slower grade of powder. CHAIRMAN LITTLEJOHN: Any further discussion, gentlemen? MR. GIBSON: Mr. Chairman, I would like to ask Mr. Bottomley, if, in his shot-firing system, as I understand it, he has a very high coal and is working something like eleven feet? MR. BOTTOMLEY: Something like that. MR. GIBSON: I read the article that you referred to. Did you use both the first and the second delay explo¬ders in shooting the coal? MR. BOTTOMLEY: We use the ordinary fuse. MR. GIBSON: That is what I wanted to find out; whether you use the delay exploders and the detonators. In Utah, we are getting away from the fuse altogether, because we do not think it is accomplishing anything to use the electric light on the cap, and' at the same time shooting with fuse. We are defeating the object we might gain in using the electric safety lamp. That is a point that might be discussed a little further. MR. E. H. JOHNSON, The Coloder Company: I would like-since it is a general opinion that mechanical loading breaks up the coal, to ask Mr. Bottomley, if he finds a larger percentage of small coal, or how much, through the use of the mechanical loaders? MR. BOTTOMLEY: We do not find any great difference. In fact, we have succeeded in improving our lump coal percentage, and that is important, because it is largely domestic. At first, when the machines were installed, the boys shot the coal too hard, and we fell down a little, about two or three per cent, the first month, in our lump percentage, and we tightened up a little and changed our methods in shooting and got on to the stunt of drilling more holes and getting a slower grade of powder. We could not load as much coal in one day as we could before, but we did succeed in in. creasing our lump coal percentage four and a half per cent over the hand method, and that is quite a factor-quite an important factor and since our domestic trade is over with, we loosened up on the shooting and we are running about the same as we did with the hand loading, maybe a half per cent more, or one per cent, but pretty much the same. MR. SHUBART: Your coal is very high? MR. BOTTOMLEY: Yes. MR. SHUBART: Have you tried sunbbing the coal before shooting? MR. BOTTOMLEY: No, we have not tried that. It is very hard coal to shoot; we have no defined cleavage in our coal. It is the worst coal I ever saw to shoot. We do not try to snub it. Formerly, as I said, the miners drilled four holes, pretty well up near the top, and then four holes down, within about three feet of the bottom. It is the same thing as a snub shot, and that we find is the best method for shooting the coal. We have not tried any mechanical device for snubbing as yet. SECRETARY SHUBART: At one mine I saw snubbing tried with a Jeffrey undercutter with a seven-foot Jeffrey bar. This mine, by the way, is very similar to Mr. Bottomley's condition. They have very high coal, so the snub cut is a small percentage. They cut a seven foot undercut and raise the machine on an eight inch tie and undercut five feet to give the effect of a snub cut, 14 inches at the front of the cut, and then six inches at the back of the cut. They made a very marked increase in lump. (The bug dust would be a small percentage of the total coal), and they increased the percentage of the slack at the same time. They found a decrease by reason of the easier shooting of about 15 per cent in their slack. In other words their nut and lump coal ran considerably higher and their slack decreased 5 per cent with the snubbing cut. Mr. Bottomley, I believe, understands those conditions.

Jan 1, 1926

By Brahm Prakash, R. Schuhmann

Chemical conditions for flotation and nonflotation of quartz with oleic acid as collector and barium, calcium, aluminum, iron, and tin as activators were studied using a simple vacuum-flotation technique in glass-stoppered graduates. The detailed study of barium activation led to an interpretation based on ideal Langmuirian chemi-sorption. FLOTATION of quartz is of practical importance as something to be avoided in soap-floating many types of ores. Clean, unactivated quartz is not floated with fatty acids and soaps, such as oleic acid and sodium oleate, in the quantities normally used for flotation. However, data in the literature indicate that almost any multivalent cation will activate quartz if given an opportunity. Thus, a common problem is to prevent activation of quartz by the various inorganic cations inevitably present in flotation pulps. Wark and his coworkers1 have demonstrated the reversibility of the chemical reactions and adsorptions involved in the activation, depression, and collection of the common sulphide minerals. The procedure in much of their work was to bring a mineral surface to equilibrium with solutions of known pH, collector concentration, and activator concentration, and then to test the floatability of the mineral by contact-angle measurement. From the data, graphs were constructed with pH and reagent concentrations as coordinates. These graphs show fields of flotation and fields of nonflotation, separated by narrow transition regions whose locations are shown by so-called contact curves. From the shapes and locations of the contact curves, which roughly separate fields of flotation from fields of nonflotation, a quantitative understanding of the interaction of the reagents with each other and with the minerals often can be deduced. The study of quartz flotation to be described in this paper follows in broad lines the approach of Wark and coworkers. That is, pH, activator concentration, and collector concentration were varied to find equilibrium conditions of flotation and non- flotation, and the results are presented graphically by means of contact curves. However, instead of testing for floatability by measuring the contact angle on a polished surface, a simple vacuum flotation technique was developed and used. Purified oleic acid was the collector and terpineol the frother. Barium activation was studied in some detail, and exploratory studies were made of activation with calcium, aluminum, ferric iron, and stannic tin. Preparation of Materials Quartz: Large lumps of high-grade vein quartz were crushed dry in a cone crusher and rolls. The —20, +28-mesh portion was screened out and used in the subsequent steps. This material was passed through a high-intensity magnetic separator to discard iron, then leached twice with hot concentrated HCl and washed repeatedly with distilled water. The cleaned sand was then wet ground with porcelain balls in a porcelain pebble mill, deslimed repeatedly by settling and decantation to discard —800-mesh material, and again washed with hot HCl followed by distilled water. The resulting stock of quartz was stored under water. Chemical analysis gave 99.8 pct SiO2. Table I gives the size analysis of the quartz used for flotation tests. Calculations from these data, using shape factors given by Gaudin and Hukki9 indicate a specific surface of about 500 cm2 per g. Blank flotation tests in distilled water, and in water with added frother, showed the prepared quartz to be completely nonfloatable and thus indicated the absence of organic contamination. Oleic Acid: The preparation of oleic acid was based on fractional vacuum distillation of methyl oleate2,3 followed by regeneration of oleic acid, and finally fractional crystallization of oleic acid from acetone solutions at low temperatures." The pure oleic acid was stored in a refrigerator. The iodine number of the oleic acid was found to be 90.0 (theoretical 89.93). Oleic acid was used in the form of a dilute water solution of sodium oleate, after preliminary flotation tests showed no effects of form of addition and order of addition of reagents when an adequate conditioning time (that is, 30 min) was provided. Other Reagents: Sodium hydroxide solutions low in carbonate were prepared by first making 1:1

Jan 1, 1951

By J. N. Breston, R. V. Hughes

Conclusions drawn by previous research workers with reSPect to the relation between Pressure gradients and/or velocity and oil recovery obtained by laboratory water flood tests have been in disagreement probably due to variable procedures and unnatural conditions and materials. The Bradford Laboratory of the Pennsylvania Grade Crude Oil Association as part of its secondary recovery research program has conducted nineteen water floods on two long cores of widely differing characteristics in an attempt to clarify this relationship and make it an aid in predicting flooding pressures in the field. Unlike previous research procedures the present experiments were conducted with the aim of duplicating field conditions as closely as possible by using long unextracted consolidated cores, a live crude, and natural brines for both flooding and, connate water content. Also, the pressure gradients and flooding velocities were representative of field conditions where similar sands were being flooded. Eleven floods on one core and eight floods on the other core showed increased recoveries and lower residual oil saturation with increased flood pressure gradients and flood velocities. A marked decrease in recovery was obtained from both cores at very low flood velocities. This pressure versus recovery relationship is shown to hold up to the point of water breakthrough and also up to the 100 and 1 produced water to oil ratio point. INTRODUCTION The possibility of water flooding oil sands was suggested by Carl1 of the Pennsylvania Geological Survey in 1880. It is not known when the practice was tried intentionally for the first time, but its beneficial effects were noted in the annual production rate of the Bradford field as early as 1907. The practice was illegal in Pennsylvania until 1921. Early water floods in the Bradford field usually consisted of shooting or splitting the casing secretly to permit subsurface waters to enter the producing sands under hydrostatic head. As it was noted that the benefits of water flooding seemed to be proportional to the quantity of water dumped into the well many also began to utilize surface sources after the practice became legal. It was probably during the middle 20's before many producers realized that the pressurehead of the water upon the producing sand determined the rate and quantity of water that would enter the sand. Hence, rate and quantity of production appeared to be a direct function of input pressures. By 1927 a few producers had ventured the installation of pressure pumps in order to increase water-input rates and production through the combination of hydrostatic and hydraulic pressures. The adoption of pressure flooding and the "five-spot" drilling pattern in the Bradford field were essentially simultaneous. Water-input pressures in 1930 seldom exceeded 300 p.s.i. at the well head or 1100 p.s.i. at the sand face. Since that time, water-flood producers in the Bradford-Allegany fields have gone to higher and higher pressure until today 600 p.s.i. at the well heads is called a low pressure flood. Many high pressure floods now operate at 1300-1400 p.s.i. at the well head. The limiting and advisable pressure at the sand face has been pronounced as that pressure just under what is required to lift the overburden or to cause formation parting: According to this rule any water flood operation utilizing well-head pressures nearly equal in pounds per sq. in. to 1.1 times the average depth in feet to the top of the producing sand would be considered as a high-pressure flood. Despite the higher pressure trends in the Bradford-Allegany field operations and the results of early laboratory water flooding research, the desirability and benefits of high input pressures are still questioned by many operators, particularly in midwestern water flood operations. The present paper recounts a series of 19 laboratory water floods using two long, consolidated cores of widely differing characteristics saturated with live crude and flooded with oil field brines in an effort to simulate field conditions under • various pressure gradients and flooding velocities. For both cores, higher recoveries and lower residual oil saturations were obtained at higher pressure gradients and flood velocities. This relationship is shown to hold up to the water breakthrough point and also up to the 100 to 1 produced water to oil ratio point.

Jan 1, 1949

By D. E. Light, J. Y. Somnay

The use of alkyl acid phosphates and their alkali salts as collectors for the uranium minerals brannerite and uranothorite was investigated. In particular a detailed flotation study was carried out using isooctyl acid phosphate as a promoter. Tests were conducted on an Elliot Lake ore analyzing 0.11% U 3 O 8, chiefly as brannerite, and approximately 9% pyrite. Pyrite was floated with conventional reagents; the flotation of brannerite from the sulfide tails was studied to determine the optimum pH and pulp density to employ with isooctyl phosphate. 4 uranium recovery of over 90% was possible with a selectivity index of 8.95 when these tails were floated at 17% solids and a pH of 1.7. The effect of various modifying agents was also investigated. Aluminum sulfate, lactic acid and sodium silicate improved the selectivity of collection yielding selectivity indices of 9.5 to 11.5. Ferric chloride was found to be a depressant for brannerite. A Bancroft ore which analyzed 0.13% U308, and contained uranothorite was also amenable to flotation using isooctyl acid phosphate. The composite uranium concentrate obtained assayed 0.41% U308 at a recovery of 95.3% and a ratio of concentration of 3.24. Previous investigations1,2 on the flotation of brannerite, pitchblende, uraninite and/or uranothorite from various Canadian ores showed that fatty acids, including oleic acid and tall oils, petroleum sulfo-nates and alkyl acid phosphates, were suitable collectors for these uranium minerals. Additional work carried out by the Mines Branch in Ottawa on brannerite ores from the Elliot Lake area3 used the tall oil Acintol FA-1, or FA-2, as a collector. A recovery of 92% of the uranium in a concentrate which contained about 55% of the weight and assayed 0.2% U3O8 was obtained from a feed of 0.1% U308 in this latter instance. Eigeles et a1.4 carried out flotation on pitchblende ores and found that the most promising results were obtained with alkyl acid phosphates and their alkali salts as collectors. Within the homologous series of alkyl phosphates, the best flotation characteristics were displayed by isooctyl phosphates. Further, isooctyl phosphate derivatives were much less sensitive to hardness forming salts than oleic acid, enabling all flotation tests to be made with tap water. This paper describes tests employing alkyl acid phosphates for the flotation of ores containing brannerite and uranothorite. The flotation work described herein was conducted in conjunction with the development of a leaching process for Elliot Lake, Ontario, brannerite ores. In this process pyrite in the ore was concentrated by flotation and roasted, providing sulfur dioxide which was used to produce sulfuric acid in situ in a liquid-solid extraction process. A 40% conversion to sulfuric acid was indicated at a leaching temperature of 80°C; this resulted in the extraction of 93% of the total uranium after a contact period of 6 hr. A rotary kiln was used as a leaching vessel. Preconcentration by flotation was studied in conjunction with the above process to reduce the bulk of solids for leaching and, consequently, capital expenditure. The materials and methods used in this study will be described initially. Then the results will be presented in two sections, the first dealing with the brannerite ore, and the second with the uranothorite. Finally an economic analysis of the results on the brannerite material will be made. MATERIALS AND METHODS The two ore samples examined were from uranium-producing mines. One was a brannerite ore, a uraniferous quartz pebble conglomerate from the Elliot Lake area, which contained 0.11% U3O8, 4.3% S and 4.5% total Fe. Mineralogical studies of similar samples indicated the presence of quartz, microcline, sericite, pyrite and minor quantities of rutile, pyrrho-tite and zircon. The other ore was from a biotite-rich pegmatite in the Bancroft area; feldspar, quartz and biotite formed the major gangue components. Uranothorite was the principal uranium mineral; the head assay was 0.13% U 3 O 8. Preparation of Feed: The ores were crushed to —10

Jan 1, 1963

By Charles T. Steuart, Richard B. Berg

Tripoli and the related mineral commodities such as micro- crystalline silica have been mined for more than 100 years for their abrasive properties. Although abrasive and buffing compound markets are still very important, within the last 15 years the filler and extender markets in paint, plastics, rubber, adhesives, and sealants have increased substantially. Tripoli or microcrystalline silica consists almost entirely of very small quartz crystals, many less than one micrometer in length. Material mined from different districts differs in crystal shape, grain size, and texture of the rock, all of which influence markets. Most US deposits are now mined by surface methods, and both air floated and micronized products are marketed. Deposits of tripoli now mined in the United States occur in chert-bearing Paleozoic limestone in the central part of the country with producing districts in southern Illinois, central Arkansas, and eastern Oklahoma. Although deposits within each district are confined to specific formations and extend laterally within those formations, individual bodies form minable deposits that are typically several hectares in areal extent. Tripoli is white to cream to rose and characterized by high porosity and ease of disaggregation. DEFINITIONS Tripoli In the United States, tripoli was first used to describe the fine-grained, easily disaggregated material from Seneca, MO, be- cause of its similarity to a rock from the Tripoli region of North Africa (Hovey, 1894). The North African rock is actually diatomaceous earth, a material that is similar in appearance to the rock from Seneca, but is of entirely different origin having formed by the accumulation of siliceous remains of microscopic marine or fresh- water animals. Tripoli is best defined as a very fine-grained, generally porous rock that consists of microcrystalline quartz, typically formed by the alteration of a chert-bearing limestone. Tripolite A term used to describe a rock from the vicinity of Tripoli in North Africa which is diatomaceous earth (Quirk and Bates, 1978) Microcrystalline Silica Microcrystalline silica is the same material as tripoli, but the distinction between the use of these two names is dictated largely by convention and markets. Material produced from southern I1linois deposits and used in white pigment and filler applications is generally referred to as microcrystalline silica, whereas that used in abrasive applications, both from the Illinois district and from other states, is commonly called tripoli. Amorphous Silica Amorphous silica, a term formerly used to describe the material produced from the deposits in southern Illinois, is now replaced by the term microcrystalline silica. Amorphous silica came into use when even optical methods for the identification of very fine- grained quartz were not widely available and the Illinois product, composed of quartz grains too small to be seen with the unaided eye, was thought to consist of amorphous silica. The Illinois material is clearly crystalline quartz, as shown by X-ray diffraction analysis and scanning electron microscopy (Fig. 1). Novaculite Although originally used to describe a rock suitable for the manufacture of whetstones, novaculite is now defined more generally " - as a homogeneous, mostly white or light colored rock, translucent on thin edges, with a waxy or dull luster, and almost entirely composed of microcrystalline quartz" (Steuart et al., 1983). The more compact rock mined in central Arkansas from the Arkansas Novaculite is referred to as novaculite, whereas the more porous rock is referred to as tripoli. Rottenstone The commodity rottenstone is sometimes included within the general mineral commodity category of tripoli. Rottenstone is mined in Northumberland County in eastern Pennsvlvania and formed by the weathering of a siliceous shale of Devonian age (Faill, 1979, Berkheiser, private communication, 1991). This material is used as a filler and extender, but is apparently unlike tripoli both in origin and physical properties. Spiculite Spiculite is a rock consisting of siliceous sponge spicules having formed by the removal by solution of the carbonate matrix of a spicule-bearing limestone. Spiculite has been mined in Texas and, because it resembles tripoli in several aspects, is included in the discussion of deposits.

Jan 1, 1994

By G. Gutierrez, D. A. Elgillani, M. C. Fuerstenau

The zero-points-of-charge of apatite, calcite, and fluorite are pH 6.4, 10.8, and 10.0, respectively. Scheelite is negatively charged above at least pH 3. In this article, the flotation responses of these minerals in the presence of potassium oleate and sodium silicate are described and compared with electrokinetic data. Colloidal silica appears to be the species principally responsible for calcite depression, while silicate anion is the species responsible for fluorite depression. Additions as high as 1 x 10-3 mole/liter silicate have no effect on the flotation responses of apatite and scheelite. Selective flotation of nonmetallic minerals is difficult to achieve with fatty acids or soaps by themselves. As a result, specific reagents are added to aid these separations, and one of the reagents commonly employed for this purpose is sodium silicate. Flotation separations of various calcium-bearing minerals such as fluorite from calcite1-3 and scheelite from calcite2,4 and apatite,2,5 for example, almost always involve the use of sodium silicate. The mechanisms by which sodium silicate functions as a depressant are still not understood, probably for a number of reasons. For one thing, the dissolution process of sodium silicate is complex, giving rise to a number of ionic and colloidal species.' Moreover, the type and concentration of these species depend on the ratio of Na2O to SiO2, the concentration of sodium silicate, and the pH of the system.' At the present time, it is not known which species, colloidal silica or silicate anion, is responsible for depression. If colloidal silica is the species that is adsorbing, then adsorption must occur by electrostatic attraction between the colloid and the mineral surface. Silicate anion, on the other hand, may adsorb either physically or chemically. The objective of this paper is to determine first the active species of sodium silicate and then the conditions under which this species will adsorb and function as a depressant. EXPERIMENTAL MATERIALS AND METHODS Pure samples of apatite (Durango), calcite (Iceland-spar), fluorite, and scheelite were used in this investigation. Pure potassium oleate was used as collector, while reagent-grade HC1 and KOH were employed for pH adjustment. The sodium silicates used were samples obtained from the Philadelphia Quartz Co. In one series of experiments, various sodium silicates containing different ratios of SiO2 to Na2O were added to calcite systems. These sodium silicates contained SiO2-to-Na2O ratios of 3.75 to 1, 3.22 to 1, 2.40 to 1, and 1.60 to 1. All other experiments were conducted with the sodium silicate containing the ratio of 3.22 to 1, which is the one that is normally used in industry. Flotation experiments were conducted with 21/2-g charges of 48 x 150-mesh material in conductivity water with an apparatus and technique described previously. Electrokinetic experiments were conducted with both a Zeta Meter and streaming potential apparatus. Particle size was 48 x 65 mesh for the streaming potential experiments. EXPERIMENTAL RESULTS The first series of experiments involved flotation of scheelite in the absence and presence of sodium silicate. As shown in Fig. 1, flotation response was not affected with even the relatively high addition of 1 x 10-3 mole per liter sodium silicate. Interestingly though, no flotation was effected below pH 6 with this collector addition. The responses of apatite to flotation under these same conditions are given in Fig. 2. Similarly, no depression was obtained in basic media under these conditions. Similar experiments were conducted with fluorite, and in this case, depression was noted above about pH 11 with 1 x 10-3 mole per liter sodium silicate (Fig. 3). When calcite was floated with these same levels of addition of sodium silicate, essentially no flotation was possible above pH 7 (Fig. 4). The effect of collector addition with a constant addition of sodium

Jan 1, 1969

By R. G. Wheeler, J. W. Goffard

The Larson-Miller parameter was used to correlate time, temperature, and indentation creep of magnesium, aluminum, and some of their alloys. In the temperature range 300" to 450°C, the short-time Meyer hardness of pure magnesium was less than that of the magnesium alloys tested, but for long times the pure magnesium has greater indentation creep resistance. Aluminum (1100 alloy) had 1.5 to 2.5 times more indentation creep resistance than magnesium at 300" and 450oC, respectively. Hardening of aluminum with a dispersion of Al2O3 was effective in the time and temperature ranges studied. New technologies have required the development of new materials and the utilization of the more familiar materials for new and unusual applications. The use of magnesium and aluminum and some of their alloys, because of their desirable nuclear characteristics, light weight, low cost, and ready availability, has been extended to the 300" to 450°C temperature range. In this temperature range the basic consideration of these materials must be their rate of plastic flow rather than offset yield strengths. The indentation testing reported here arose from a need for design data for the load-holding ability of supports made of these materials. Test Procedure—Hardness indents were made with a 0.275-in.-diam quartz indentor and a 10.65-lb load. The indentor was made by fire-polishing a spherical surface on the end of a fused quartz rod. The samples were held at temperature in a graphite crucible controlled to ±2°C. A thermocouple was attached to the sample and test temperatures were recorded. The diameter of the spherical indentation was measured at the end of a test period and the compression stress (Meyer Hardness) was determined by: H___________load__________ m = projected area of indent Samples were 1 in. in diam and at least 1/4 in. thick. It was observed that at the higher temperatures and longer times, the quartz indentor would stick to the magnesium sample. The quartz indentor was, therefore, frequently inspected and fire-polishing repeated when necessary. The area of sticking was always a small fraction of the area of indent and was therefore considered to have an insignificant effect on results. Correlation of Hot-Indentation Test Data with Time-Temperature Parameter—Sherby and Dorn' have correlated creep or tensile data of a' solid solutions of aluminum with a temperature and strain-rate parameter suggested by Zener and Holloman. underwood2 used this parameter to correlate creep properties of some steels with hot hardness, and upon the basis of this correlation a means of obtaining creep properties from short-time (and inexpensive) hot hardness tests has been demonstrated. Since the validity of the correlation of creep properties with a time-temperature parameter and the correlation of creep properties with hot hardness have been shown, it follows that hot hardness may correlate with the time-temperature parameter. The hot-indentation data obtained was expressed as Meyer hardness, and was shown to be time and temperature dependent. Correlation of Meyer hardness, time, and temperature with the parameter was made using the relationship: Hm = Meyer hardness t = time, hours T = absolute temperature, OK K = constant A value for the constant K was calculated by equating In l/t + K/T at different temperatures and times but at the same hardness. The correlation was tested by plotting Hm vs the parameter, In 1/t +K/T. Since materials are being sought which have high hardness at low indentation creep, i.e., a high Meyer hardness for long time at high temperatures, low values of the parameter are ofthe most interest. TEST RESULTS Magnesium—Pure magnesium (99.98 pct) cut from extruded rod was indentation tested perpendicular to the rod axis at temperatures of 300°, 350°, 400°, and 450°C for times ranging from 6 sec to 112 hr. Fig. 1 shows the time dependency of Meyer hardness at the four constant temperatures. Fig. 2 shows the correlation of the Meyer hardness of pure magnesium with the time-temperature parameter using a K of 22,720 in Eq. [I]. At the bottom of Fig. 2, the effect of doubling the time of indentation t2 = 2(t1), on the abscissa for any time is shown graphically. This effect is of constant magnitude. Also shown graphically are the magnitudes of the effects on the

Jan 1, 1960

By R. F. Mehl, R. F. Bunshah

A fast amplifier technique has been developed for the measurement of the rate of propagation of martensite in an Fe-29.5 pct Ni alloy. The time of formation of one plate of martensite is 3x10 sec and the rate of propagation is 3300 ft per sec approximately. IT has been known for some time that the plate-like structural unit of martensite forms from austenite with great rapidity. Wiester1 and Hane-mann, Hofmann, and Wiester took motion-pictures of the transformation as it occurs in a 1.65 pct C steel; they demonstrated that a single plate formed fully in the time interval between successive frames, viz., 1/20 sec, thus setting an upper limit. Forster and Scheil,3 using an Fe-Ni alloy with 29 pct Ni, recorded the sonic characteristics of the process electrically, upon an oscillograph, setting the upper time limit at 0.002 sec. Forster and Scheil,~ measuring the change in electrical resistance in the same alloy upon a cardiograph, set a limit of 0.02 sec. Forster and Scheil5 later, employing the same alloy, improved their technique, reporting an upper limit of 7.10 sec. In studying signals of such short duration, it is an important question whether the frequency response of the electrical system used is high enough compared to frequency of the pulse measured, or, put differently, whether the system is able to reproduce without distortion the signal arising, in this case, from the formation of a single martensite plate. Forster and Scheil (referring only to their last paper) obtained signals of a frequency of 30 kilocycles (hereinafter kc); this was about the frequency response of the equipment used; thus, if the signal had a frequency higher than 30 kc, it would still appear as a signal of frequency 30 kc. All of these results thus provided upper limits only. Recent developments in electronics have made available equipment with very high frequency response, very high sweep-speeds, high gain, etc. The electrical characteristics of such equipment, used in the present study, are given in Table I. Such equipment offers obvious attraction in the study of the rate of propagation of a martensite structural unit—and perhaps of other structural alterations proceeding at a very high rate. This paper reports an attempt to develop a technique employing such equipment to measure the time of propagation of a martensite structural unit and the variation of this with temperature, with the mode of formation—athermal and isothermal—in both polycrystalline and single-crystal samples; and from such measurements to obtain the rate of propagation. As will be seen, the results obtained are useful theoretically. Materials All data presented here are for an Fe-Ni alloy of the following analysis: 29.5 pct Ni, 0.027 pct C, 0.135 pct Mn, 0.094 pct Si, balance Fe. There were several reasons for choosing this alloy: 1—it is substantially the one used by previous investigators; 2—it exhibits both the athermala and the isothermal' mode of formation of martensite, both studied in detail by Machlin and Cohen; 3—the subzero temperatures of transformation in this alloy are experimentally very convenient; 4—it exhibits the "burst phenomenon";" 5—the change in electrical resistance upon the formation of martensite, a decrease, is great, approximately 50 pct.' The polycrystalline specimens were in the form of wires of 0.025 in. diameter; the single crystals were 1x1/4x1/4 in. Experimental Methods Electrical Apparatus: Fig. 1 is a schematic drawing of the electrical circuit used. The principle used in these measurements is the same as that used by Forster and Scheil." A small direct current, about 1 to 2 amp, is passed through the sample. When a martensite plate forms, the resistance of the sample changes and a high frequency signal is generated. This signal is picked up by the probes attached to the sample, fed into the bank of amplifiers and thence to the vertical deflection plates of a cathode-ray oscilloscope. The signal itself triggers the oscilloscope trace which flashes across the tube face and is photographed by means of a 35 mm movie camera at the end of a light-tight hood. The camera has no shutter. As soon as the signal flashes

Jan 1, 1954

By A. W. Sommer, H. H. Kellogg

It is shown that SO3-O2 mixtures react with sphalerite at an appreciable rate ill the temperature range of 361° to 527°C to fornz ZnSO4. The rate of reaction follows a parabolle lax. Oxygen, or O2-SO2 mixtures, have a negligible effect on sphalcrite in the same temperatuee range. PRACTICAL roasting of sphalerite is usually performed at 800°C or higher. The calcine is composed of zinc oxide unless the roaster atmosphere contains relatively large amounts of SO2 and the temperature is held to 800oC or lower, in which case zinc sul-fate may also form. Ong, Wadsworth, and assell' have made a careful kinetic study of sphalerite oxidation under these "normal conditions" and have concluded that the rate of the reaction is controlled by the decomposition of an activated complex adsorbed on the sphalerite surface. They found the rate of oxidation to be small at 700°C. Extrapolation of their data to 400°C would indicate an almost negligible rate at this temperature. In our work sphalerite was reacted with air, mixtures of SO2, O2, and N2, and mixtures of SO3, O2, and N2 in the temperature range 361o to 527OC. Negligible rates of oxidation were found, except for the gas mixtures containing SOs. With this latter gas, the oxidation of finely divided sphalerite was fairly rapid and zinc sulfate was the product. Based on the limited evidence available, the rate of sphalerite oxidation by SO3 is postulated to be controlled by gaseous diffusion through pores or cracks in the zinc-sulfate coating. This evidence for the direct reaction of sphalerite and SO, at low temperature may prove of importance to the understanding of zinc-sulfate formation in the dust-collecting equipment usually associated with zinc roasters. The roaster gas carries off fine dust, much of which may be unreacted sphalerite. The temperature in dust-collecting equipment drops from the roaster temperature (about 800°C) through the range of temperature we studied, to ambient temperature. Such dusts are known to contain far larger amounts of zinc sulfate than the primary calcine. It has been assumed in the past that this sulfate is formed by reaction of ZnO dust with SO3 (or SO, plus 0,) in the partly cooled gases. Our work shows that an alternative possibility exists—the direct reaction of SO3 with ZnS dust. EXPERIMENTAL Reaction rates for sphalerite at 350° to 600°C are relatively small so that it was necessary to use finely divided material with a relatively large surface area in order to obtain measureable amounts of reaction. In the preliminary experiments, pure mineral sphalerite, ground to pass a 325-mesh sieve, and chemically precipitated ZnS (in the form of an impalpable powder) were used. In the quantitative rate experiments the ground mineral sphalerite was processed in an Infrasizer to obtain a product with particle size between 9 and 18 µ. The analysis of this material was 66.7 pct Zn, 0.09 pct Fe, and 32.7 pct S (theoretical sphalerite is 67.1 pct Zn, 32.9 pct S). The sized powder was carefully mixed and divided into l-g samples. The apparatus used for the quantitative rate measurements is shown in Fig. 1. For the preliminary experiments the following change was made: The external catalyst furnace (B, C)* was not used. *Letters refer to Fig._______1 .___- Rather, when catalysis of the SO2 + O2 reaction was desired, the glass beads in basket M were replaced by vanadium-oxide pellets. Procedure—A l-g sample of ZnS was placed on a shallow stainless-steel tray, I, and spread evenly to a depth of about 1mm. The tray was placed in the reaction assembly and the assembly inserted in the cold furnace. The furnace tube was flushed with dry argon and then heated to the desired reaction temperature. The temperature was controlled to ±0.5oC. Gas mixtures (O2 + N2 or O2 + SO2) were prepared from tank gases by means of a mixing device identical to that employed by Darken and Gurry.2 The total flow rate of gas was 205 ml per min to point A of Fig. 1. The accuracy of the individual and

Jan 1, 1960

By L. C. Lang

INTRODUCTION The introduction of 165-mm (61/z-in.) holes to underground mining operations has made possible the application of Canadian Industries Ltd's (CIL) vertical crater retreat (VCR) mining method, illustrated in the accompanying sketches. This unique and revolutionary new application of spherical charge technology (see the Appendix), when applied to primary stopes and pillar recovery, eliminates raise boring, slot cutting, and dilu¬tion of ore by backfill; greatly improves fragmentation; reduces labor and time requirements; eliminates uphole drilling and blasting; and minimizes or completely elimi¬nates damages by blasts to the walls and retreating backs of the stope or pillar. If vertical large diameter holes are drilled on a designed pattern from a cut over a stope or pillar to bottom in the back of the undercut, and spherical charges of explosives are placed within these holes at the calculated optimum distance from the back of the undercut and detonated, a vertical thickness of ore will be blasted downwards into the previously mined area. Repeating this loading and blasting procedure, min¬ing of the stope or pillar retreats in the form of horizontal slices in a vertical upwards direction until the top sill is blasted and the mining of a stope or pillar is completed. The VCR method is also applicable to drop raises and has the potential to replace all other raising methods under most circumstances. PILLAR RECOVERY Levack Mine Inco Metals Co., Ontario Div., provided the first opportunity for the method in pillar recovery. The Levack mine's high grade ore pillar No. 4800 on the 975-m (3200-ft) level was used for the production¬scale experiment (Figs. 1 to 3). The pillar was about 49 m (160 ft) long, 6 m (20 ft) wide, and 20 to 26 m (65 to 85 ft) high. The mined area on both sides of the pillar was backfilled with a 1:30 cement:sand mixture. The pillar was removed in two phases. In phase 1, the standard uphole method was used to blast down the 18-m (60-ft) long section of waste from the bottom of the ore into the undercut. From the pillar's top sill, 165-mm (61/a-in.) holes were drilled downward into the pillar, and by measuring the depth of the holes, the results of the uphole blast were determined and roof line 1 was established. The bottom of each hole was plugged, then filled with sand to place the center of gravity of each spherical charge (loaded from the top sill) at a predetermined optimum distance from the horizontal free surface. The charges were then detonated. After detonation, both draw drifts were full of extremely well-broken material. The depth of each hole was measured again, and the plot of these depths re¬sulted in roof line 2. The same blasting procedure was repeated and the resultant new back elevation was marked by roof line 3. The poor results of the initial uphole blast at one location (notice the peak in area 1) appeared to influ¬ence the subsequent new backs. A third blast success¬fully evened the back, and resulted in roof line 4. An unblasted slab averaging 6.3 m (20.9 ft) thick remained below the pillar's top elevation as the final sill. In all three spherical charge blasts fragmentation of the blasted material was extremely fine. The backfill was fully exposed on both sides of the now-blasted pillar. The backfill remained undamaged and the ore was not diluted by sand. The remnants of all the 165-mm (61/2 -in.) holes remained clean and undamaged, and the holes had well-defined bottoms that could be easily measured and plugged. Each blast took down a 3.9 to 4.2-m (13 to 14-ft) thick horizontal slab of ore. Productivity was three times greater than that of the previously practiced cut-and-fill method. Since this was the first such experiment, blasting the remaining 6-m (20-ft) thick final slab was the sub¬ject of some deliberation. If the described method was repeated, we could have ended up with a 1.8-m (6-ft) thick sill unsafe to work on. It was therefore decided to blast the whole sill using two spherical charges prop¬erly placed in each hole, but with the application of

Jan 1, 1982