Search Documents

By Saieb Haddad, Henry Pate

"Building retaining walls in an urban area is becoming more difficult due to right-of-way restraints. Using standard concrete cantilever walls requires a construction easement behind the walls for installation, which for the most part is unavailable. To install these types of walls in a limited right-of-way requires extensive temporary walls to minimize the construction easement. Top-down construction walls utilizingtie-back anchors for support require either the purchase of the right-of-way or underground easements in the area of the anchors.These problems faced the Department on Interstate 75 widening in Knoxville, TN in an area of a large cut. A multi-story Insurance Building and a large commercial Retail Center were located at the top of the cut. To prevent any impact on the buildings, the walls had to be placed within a limited area. The option of buying the properties was prohibitively expensive. Due to the height of the two walls and the variability of the underling rock line, contiguous caisson pile cantilever walls were contemplated as the only wall type that would be appropriate. The cost of the two walls was estimated to be very close or even higher than the cost of purchasing the two buildings. The Department believed that there must be a better way to deal with the problem. A vertically tied-down pile frame wall constructed from the top-down with a concrete facing was developed. This allowed the construction of the walls to be restricted to the available limited area and provided substantial savings for the State.INTRODUCTIONThe widening of I-40/75 has been a major transportation project in the Knoxville area which is being constructed by the Tennessee Department of Transportation. The project includes 18 Retaining Walls and 13 Bridges.Two of the 18 Retaining Walls, refer to Figure 1, are to support two valuable properties, one being an insurance company housed in a multi-story office building and the other a suburban shopping center which were appraised at $13.0 million and $5.0 million respectively. Due to the 31 ft. (9.5m) maximum height of each of the two Retaining Walls and the limited Right-of- Way of 15.0 feet (4.6m), a contiguous caisson pile cantilever wall was proposed for each of the two retaining wall sites with an estimated cost of $12.0 million each. The contiguous pile cantilever Wall is comprised of a line of caisson piles socketed into underlying competent bedrock. The design required that 4 ft. (1219mm) dia. piles be installed at 6 ft. (1.83m) centers, socketed into rock in order to provide lateral stability and restrict lateral wall movement to acceptable limits. The line of caissons would be fronted with a cast-in-place concrete face wall"

Jan 1, 2007

By P. Cowx, L. Els, P. Smith, R. Nordhagen

"Tapping operations at ferroalloy smelters generate a significant amount of fume. Effective capture of fumes is required to meet the obligations of environmental, as well as occupational, legislation.A study was completed on an existing fume extraction system at a ferromanganese furnace tapping area. The area under consideration included the tap-hole, launder, and ladle area. The study consisted of site test work as well as computational fluid dynamics (CFD) modelling to identify and evaluate solutions.Site test work and observations during furnace operation provided a baseline of system performance as well as input parameters for CFD modelling. Gas flow rates and energy contents from each extraction area were measured. Photographs and video footage were taken to evaluate areas of fume leakage.The CFD study was firstly validated against site observations to ensure the accuracy of input parameters. Thereafter several modification concepts were modelled and suitable combinations were investigated to ensure robust solutions. The following concepts were considered:•,Air curtains•,Ladle hood aspect ratio and position•,Increase of ladle extraction volume•,Extension of the length of the tapping garage structureThe paper presents the results of a performance test on a working ferromanganese tapping area fume extraction system and the results of CFD modelling as compared to site test results. Upgrade options are evaluated and an integrated robust upgrade of the system described."

Jan 1, 2014

By Bin Du

In recent years, concurrent product design and process is gaining popularity and will become a norm of the industry of the future. Forging has been a critical manufacturing process for production of components with superior tensile strength, toughness and grain flow. This paper describes an expen system which is being developed for forging die design and forging process analysis in concurrent engineering environment. Rules and guidelines pertaining to forgeability are formulated and incorporated into the knowledge-base in building the system. The system is built using an object-oriented paradigm. The object-oriented approach and hierarchical rule structure paradigm are briefly discussed. Finite element analysis packages (ALPID-2D) were incorporated into the program to give the simulation result of the forging process. The system can automatically produce a competent design and recommend a set of processing parameters for a given product. The designer can modify the design according to the result of the simulation.

Jan 1, 1992

By D. Malhotra

Climax byproduct-plant tailing assayed 0.019 percent WO3. Pilot-plant and laboratory tests were performed to investigate the possibility of recovering additional tungsten values from the byproduct-plant tailing. The paper discusses the methodology used in the study and the results of this investigation.

Jan 1, 1985

By Ricardo Montero

At this time, over 300 tons of Au are used in electronic equipment each year with other precious and strategic metals such as Ag, Pt, Pd, Cu, Nb, Ta, etc. After the use-phase, the electronic devices become electronic waste (e-waste); consequently it is important to consider e-waste as a secondary supply for recovery of these metals. One of the most important components is the printed circuit boards (PCBs) because the amount of their precious metals is ten times higher than rich precious metals bearing ore. This paper presents the recovery of Au, Ag, Cu and Nb from PCBs of discarded computers using leaching column technique. The amount of these metals in used PCBs was: 613 g/ton of Au, 1515 g/ton of Ag, 36 g/ton of Nb and 23.4 % of Cu. The PCBs were crushed with a hammer mill until reaching a particle size between 3.33 mm to 0.43 mm. Then, it was leached with sodium cyanide solution in a glass column using the following conditions: sodium cyanide concentration 4 g/L, flux 20 L/kg PCBs day, pH between 10.5 to 11 and leaching time 15 days. Every day, after leaching, the pregnant solutions passed through a column with activated carbon to complete the closed loop system. The following recoveries were obtained: 46.6% of Au, 51.3% of Ag, 47.2% of Nb and 62.3 % of Cu. The products obtained are: a) loaded carbon that contains the desired metals and b) processed PCBs with precious metal contents. A preliminary technical-economic study shows the feasibility to create a small-scale PCBs recycling plant. The initial investment is on the order of US$ 155 639, considering the recovered metals from loaded carbon. The internal rate of return for 10 years period (IRR) and net present value (NPV) estimated are 27% and US$ 105 926 respectively. Keywords: printed circuit boards, recovery, precious metals, niobium, leaching column

Sep 1, 2012

By C. H. Perbix

[On Pier D in the Port of Long Beach, California, the Port of Long Beach has built a new bulk cement distribution terminal. The facility is operated by Pacific Coast Cement Corporation, who designed the complex and leased it from the Port of Long Beach on a 40-year lease. At one bulk cement is unloaded from vessels carrying from 12,000 to 30,000 t. The unloading is performed with pig speed mechanical unloading equipment and delivered into a concrete silo complex with, a capacity of 50,000 t. From the silos, bulls cement is loaded into trucks for delivery. The facility was completed in September 1981.]

Jan 1, 1983

By M. Ito

Cobalt-rich ferromanganese crust and nodule ores from seamount areas contain volcanic and sedimentary rocks as substrate or nuclei. These ores require mineral processing to remove the sub-strate/nuclei rock before smelting. This paper reviews experimental results of previous investigations. Observations and analysis of 10 samples from different localities were carried out and it was found that the liberation ratio of crushed product was high even at coarse size fraction, 0.5mm to 4mm. Experimental and calculated results in the smelting stage confirmed that the separation product satisfies the standards of the subsequent smelting process if the substrate/nuclei rock is removed from the 0.5mm to 4mm fraction with high separation efficiency. There was a density difference between the substrate/nuclei rock and the ferromanganese component. Thus the coarse sized sample was treated with gravity separation; air table separation was used as a dry method and jig separation as a wet method and high grade values with high recoveries were obtained by both kinds of gravity separation.

Jan 1, 2014

By M Gabbitus, B Young, T Lukins, M Slater

This paper details the implementation of a new type of grade control system at the Black Star open cut mine in Mount Isa, Queensland. It explores the site requirements for grade control, what as previously in place and what the site required moving forward. It also details some of the features of the system installed and why it was chosen over other grade control systems available. Black Star open cut mine has been in operation since late 2004, and was developed to extract the surface extents of the Ag-Pb-Zn mineralisation previously mined in the Isa Lead Mine. Black Star is currently mining seven distinct orebodies in and around active void hazard zones and hence, its grade control requirements are very detailed and complex. The implementation of a new system to manage the model update and block out processes was, therefore, of critical importance to the site and required a detailed understanding of the requirements of the entire mining team from drilling through to geology, survey and production. Having previously run the grade control process using site specific æblack boxÆ scripts and macros, Black Star needed to implement a more open, auditable and flexible system, which allowed the geologists to control the process and make strategic changes as the situation demanded. MineSightÆs Axis Grade Control, with its flexible, generic framework for managing the process, met these demands. Being an out of the box solution that requires minimal setup and training was also a key factor in the decision to use it.CITATION:Lukins, T, Slater, M, Gabbitus, M and Young, B, 2012. The introduction of axis at Black Star Open Cut, in Proceedings Eighth Open Pit OperatorsÆ Conference , pp 71-74 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 18, 2012

By Boris CARO VARGAS, Bernard Theron

"In early 2014, Nicholson Construction Company was awarded, together with its tunneling sister company Bessac, the Norris Cut Miami Tunnel Project. The 2.5-meters diameter segmental lined tunnel, 1600-meters long, is aimed to replace the existing 54” force main connecting the Waste Water Treatment Plant (WTP) on Virginia Key to Fisher Island. To overcome project challenges such as the highly permeable limestone of the Fort Thomson Karstic Formation (one of the most permeable formation in the World), the project team has developed State of the Art solutions: The TBM was launched with pipe-jacking technique for the first 70-meters and then converted to segment erection mode. It allows substantial schedule savings and drastically reduces the size of the circular launching shaft. The TBM, jointly designed and manufactured by Bessac and Herrenknecht, can convert from slurry to EPB mode within a few minutes. The cutters can be replaced by wet divers thanks to an innovative application in the TBM industry. PRESENTATION OF THE PROJECT The aim of this project is to replace the existing 54-inch force main pipeline which transmitted all sewage collected from Miami Beach, Surfside, Bal Harbour, Bay Harbor, North Bay Village and Fisher Island to the Central District Wastewater Treatment Plant (CDWWTP) to Fisher Island. The existing pipeline consisted of pre-stressed concrete cylinder pipe which is in poor condition in a number of locations and could be subject to sudden failure. An adjacent portion of this existing force main under the Government Cut (North Fisher Island) has already been replaced as part of a previous design-build contract and involved the installation of a 60-inch diameter fiberglass-reinforced mortar pipe installed inside a micro-tunneled casing."

Jan 1, 2016

By Dale Preece, Mike Stern, Steve Piercey, Ayman Tawadrous, GC Zhao

The McArthur River uranium mine in Saskatchewan, Canada is the world’s largest high-grade uranium mine. It has employed a freeze-wall system consisting of multiple freeze pipes to control the large quantities of water encountered during mining.

Jan 1, 2011

By Toshitaka Ota, Hisao Suzuki, Minoru Takahashi

"Perovskite-type lead zinc niobate (PZN) exhibits excellent electrical properties such as high dielectric constant, high electrostrictive coefficient and superior piezoelectricity. Therefore, PZN ceramics are very promising for high performance electronic devices. However, perovskite phase PZN is not stable under the ambient atmosphere. Accordingly, it is very difficult to prepare single-phase perovskite PZN ceramics. In this study, A-site cation of lead was partially substituted for barium to stabilize the perovskite phase of the PZN (Ba-doped PZN) powder. In addition, molecular design of an alkoxide precursor was controlled for a low-temperature processing. As a result, molecular design to suppress the lead-volatilization during calcination was preferred for a low-temperature processing. Processing temperature for a single-phase perovskite was depended on the amount of barium dopant. Doping of20 mole% of barium resulted in the single phase perovskite at 900 °C. The temperature for the single phase perovskite of Ba-doped PZN powder, which depended upon the amount of Ba-doping, was lower than that of the powder prepared by the atmosphere controlled conventional powder processing at least by 150 °C.IntroductionFerroelectric thin films and powders with perovskite structure are of renewed interest for micro-electronic applications, including ferroelectric random access memory (FRAM), dynamic random access memory (DRAM), and thin-layer capacitors integrated onto a silicon wafer [1-3]. In addition, recent advancement in micro-machine requires a high performance micro-actuator [4]. A perovskite type relaxor of Pb(Zn113 Nb213)03 is one of the promising materials for a high performance capacitor and microactuator because of their high permittivity and electrostrictive coefficient [5]. Therefore, this paper focuses on the low temperature processing of Ba-doped PZN powders.Chemical solution deposition (CSD) from molecular-designed alkoxide precursor solution is one of the most promising techniques for processing high-performance powders and thin films because it offers precise control of compositions on a molecular scale as well as a low processing temperature [6]. However, chemical solution deposition of perovskite type PZN powders and ceramics are very difficult because of the formation of stable pyrochlore phases. Therefore in the past, PZN powders and single crystal have been prepared by the hydrothermal method or flux method as well as the partial substitution method of a A-site cation [7-10]. In this study, a suitable molecular design for a preparation of perovskite type Ba-doped PZN powders with a chemical solution deposition process is investigated as well as the effect of A-site cation substitution. Chemical solution deposition from molecular-designed alkoxide precursor solution is expected to decrease the amount of a A-site substitution and/or a crystallization temperature for a single phase perovskite. This paper describes ""the relation between molecular-design and processing temperatures for a single-phase perovskite of Ba-doped PZN powders in comparison with the conventional oxides mixing method."

Jan 1, 2000

By A Wanninayake, E Novello, I Gillani

A residue storage facility (RSF) was designed to cater for Davidson Creek Area and Robertson Range Area operations under the FerrAus Pilbara iron ore development project in the Pilbara Region, Western Australia. Annual ore production was about 15 million tonnes over a period of up to 15 years. The RSF was designed to handle a tailings production rate of 2.2 Mt/a over the project life with ability to be expanded at a later date. The composition of tailings was predominantly -45 ¦ material with some spiral reject material. The fraction of solids was expected to be between 40 per cent and 50 per cent solids by weight.The RSF was designed as an above ground storage facility, integrating with a mine waste dump planned close to the selected RSF site. This integration helped to increase the stability of the RSF embankment and to reduce the construction cost. The main source of construction material for the remaining part of the RSF embankment was selected to be mine waste. The RSF was designed to be constructed in stages by considering the availability of mine waste according to the mining schedule. The use of mine waste for construction of RSF embankments has several benefits over use of borrowed material. These include less construction costs and less disturbances to the environment, by minimising borrowed areas and waste dump footprints.CITATION:Wanninayake, A, Novello, E and Gillani, I, 2013. Effective use of mine waste in the design of a residue storage facility, Pilbara region, Western Australia, in Proceedings Iron Ore 2013 , pp 39-44 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By Youngsoo Song, Hyunjung Kim, Junhyun Choi, Siyoung Q. Choi, Gahee Kim

In this study, for the first time, to confirm the effect of bacterial growth phase on the malachite flotation were investigated in a well-controlled Hallimond tube system. The test results showed that the bacteria in the stationary phase exhibit two-fold greater floatability than those in mid-exponential phase. To understand the observed flotation behavior, complementary cell characterization tests and cell attachment tests were conducted. Interestingly, the bacteria at both phases exhibited similar surface properties as well as almost identical amount of cells attached onto the malachite, suggesting that the growth phasedependent flotation behavior cannot be attributed to the variation of cell surface properties and the extent of cell adsorption. On the other hand, cell detachment tests revealed that the amount of cells detached from the malachite surface is greater for the mid-exponential phase than the stationary phase due to the higher fluid drag applied to the cells at the mid-exponential phase, which was explained by the differences in the size and shape of attached bacteria onto the malachite surface. These morphological characteristics were found to cause the bacteria of mid-exponential phase to be separated highly sensitive and easy from malachite surface due to the fluid flow. Second, scale-up selective bioflotation tests were carried out in a 1 L Denver cell in malachite–silica binary mixture systems. Through the tests, we optimized the cell concentration and the malachite fraction in the feed. Overall, high malachite selectively was observed under optimized conditions (both recovery and grade showed more than 90%). The trend was in agreement with classical DLVO interaction energy profiles, which show the relative magnitudes of the adhesive forces between the mineral and the attached cell under equal hydrodynamic conditions.

Jan 1, 2016

By R. Hogg

"Agglomeration processes and agglomerate characteristics are largely controlled by the forces of interaction between particles. The nature and typical magnitude of these interaction forces are evaluated relative to the external forces commonly present in agglomeration systems. The specific roles of the interaction forces in the various stages of agglomerate formation and growth and their effects on the integrity and mechanical strength of agglomerates are briefly reviewed. Because the interaction forces affect different aspects of agglomerate development in different ways, conflicting requirements can arise. Examples of such conflicts are given and used to demonstrate the importance of evaluating the effects of interaction forces etc., in the context of the overall agglomeration process and its ultimate objectives.INTRODUCTIONThe term agglomeration is generally used to refer to processes whereby discrete particles are caused, or allowed, to associate into clumps in which the individual particles retain their identity but are held together by relatively weak, usually physical forces. Various other designations are given to these processes, depending on the specific circumstances under which agglomeration occurs. The terms balling and pelletizing are often used to describe agglomeration in dry or semi-dry powders; coagulation and flocculation are used to refer to agglomeration of particles dispersed in fluids. Common to all of these cases is the fact that the formation, growth and integrity of the agglomerates depend primarily on the forces acting on and between particles. The same forces are, of course, responsible for manyaspects of the behavior of colloidal systems and their study and evaluation constitute the,basis for colloid and interface science.FORCES ACTING ON FINE PARTICLES AND AGGLOMERATES It is convenient to classify the forces acting on and between particles into two general types: external forces and interaction forces. It should he recognized, however, that a sharp distinction is not always possible.External Forces Gravity and inertial forces act on all particles and their magnitude is proportional to particle mass, i.e. they vary with the cube of particle size. Such forces are oftensignificant for large agglomerates but may be negligible for individual, fine particles.Hydrodynamic (""drag"") forces are important, for particles suspended in fluids. For very small particles, the drag force is directly proportional to size (Stokes' Law) while for very large particles or agglomerates it varies with approximately the square of size (Newton's Law). A useful procedure for estimating drag forces over a broad range of particle sizes and physical conditions has been given by Concha (1)."

Jan 1, 1989

By R. Mathur

Cu isotope fractionation in low-temperature aqueous environments has been well documented. Here Cu fractionation was applied to two distinct, yet related, mining problems. First, an exploration geology application, where copper isotope fractionation was measured in oxidized leach caps, chalcocite enrichment blankets and hypogene mineralization in three porphyry copper deposits located in the southwestern U.S. Cu isotope patterns exist in a vertical distribution within the mines, coupled with distinct relationships with the Cu grade. Second, a hydrometallurgical application, where copper isotope fractionation was measured in leach fluids, feed and residues from a quick leach test (QLT) on Cañariaco, Peru ores. The results indicate the relative proportions of the minerals providing Cu during leaching. Interpretations of the QLT test measurements indicate covellite is the dominant ore mineral providing Cu during leaching. Both applications clearly demonstrate the use of the Cu isotope technique to understand low-temperature aqueous processes involving copper.

Jan 1, 2012

By Sepideh Damavandinejad Monfared

"In recognition of the practicality of using inclined micropiles as elements for foundation support to resist static and seismic loading conditions, specifically in retrofitting projects, this study presents an investigation into the behavior of an inclined micropile subjected to simultaneous lateral load and bending moment. Three-dimensional numerical simulations are performed using the finite element method to assess the influence of micropile geometrical parameters such as angle of inclination, length, and diameter on the response of micropile-soil system. The Mohr-Coulomb failure criterion is used to define the behavior of soil and stabilized soil around micropile materials and the micropile, constructed of concrete and steel, is assumed to be elastic. The interaction between soil and micropile is taken into account by defining interaction elements covering both tangential and normal behavior. The study is carried out using nonlinear FEM analyses. The results of these simulations indicate that negative micropiles, in which slip surface deflects downward, have higher lateral load capacity than positive micropiles with slip surface deflecting upward. The conducted research also shows that increasing the diameter and the length of micropile increases the lateral load capacity. Increasing micropile diameter is more effective in increasing lateral load capacity. A relationship is developed from statistical regression analysis of the finite element modeling computations to estimate the lateral displacement of a micropile inclined at an angle of 30o in silty sands. IntroductionMicropiles are small diameter (typically less than 300 mm), cast-in-place, drilled, and grouted replacement piles with steel pipes which after being conceived in Italy (Lizzi,1978), were originally developed for underpinning existing structures (Bruce et al.,1990) to arrest and prevent structural movement, upgrade loadbearing capacity of existing structures, repair or replace deteriorating or inadequate foundations or raise settled foundations to their original elevation."

Jan 1, 2017

By B. Mishra, Rahul Mohanty, Swati Mohanty, Swagatika Dash

Wet high intensity magnetic separators have been widely used in the mineral industry for separation of mineral particles based on magnetic properties. Usually, magnetic separators employ ordered array of grooved plates such as Lenoir and Jones plates onto which the magnetic particles get attached in the presence of a magnetic field. In the present work, we have carried out computational fluid dynamic (CFD) simulation, using Eulerian-Eulerian model to study the flow dynamics of magnetic and nonmagnetic particles within a matrix consisting of 2 mm size spheres of magnetic material, which are interconnected by wires, in the presence of a magnetic field. The three phases considered were the water, magnetic particles and non-magnetic particles. Model equations were developed considering each sphere in the matrix as a magnetic dipole, and the strength of the magnetic field at any point in the domain is due to all the dipoles. The size of the magnetic and nonmagnetic particles was 45 and 40 micron, respectively. The feed consisted of a slurry having 25 wt. % solids. The volume fraction of the magnetic particles was 0.04, and that of the non-magnetic particles was 0.045. The simulation was first carried out without the imposition of the magnetic field till a steady state was reached, and then the magnetic field was applied. The magnetic particles, as they flow down the matrix were attracted towards the region of maximum field gradient, which was in the central region of the matrix. A symmetrical pattern in the upper half as well as the lower half of the matrix was observed. As the particles moved downwards, the pattern changed, and near the outlet, most of the particles were found to flow out from the central part of the plane. This study can lead to a better design of a magnetic separator.

Jan 1, 2014

By M Parcell

"Ventilation risks in an underground mine have essentially remained the same for centuries, yet theevidence suggests that there are many coal mines that have failed to adequately control these risks.The conduit for the knowledge learned by previous generations exists in the mining legislation. In an ideal world, mines would not need legislation to tell them what to do; they would resolve the risks to an acceptable level so as to protect the safety of persons in the mines based on the acquired knowledge. There will be some who have been personally aff ected by a mining disaster but for the majority they will be remembered as a vague recollection of an event from long ago. The mining legislation is the repository for the knowledge and outcomes from inquiries of past disasters. The challenge for the current generation, and the generations to come is to appreciate the legislation that exists, so as to not ælearn the hard wayÆ. In reviewing most disasters there is comment or discussion on the adequacy of the legislation, which ultimately results in some amendment to the law. For each person, there is an increasing responsibility to ensure that the same mistakes are not repeated. Understanding the legislation, its history and its purpose is the fi rst step in ensuring thatventilation risks are eff ectively managed. Failing to do this will be disastrous. This paper discussesthe relevance, importance and potential pitfalls of coal mine ventilation regulation."

Jun 1, 2012

By C. Y. Wang

Based on Slurry Electrolysis, and combined with the problems of extraction antimony, lead and their separation from complicated antimony-lead concentrate, a series of tests have been done in this paper. Using Slurry Electrolysis to treat complicated antimony-lead concentrate, antimony and lead can be separated in one step. And 2# metal antimony can be achieved in cathode directly at the same time. Lead in concentrate is restrained still in the residue at the form of PbCl2. After converting the residue with ammonium carbonate and removing sulfur with kerosene, the high quality of lead concentrate (Pb is above 45%, S is below 15%) and pure sulfur can be achieved, respectively. The recovery of all in Slurry Electrolysis process is as: Sb 95%, Pb 95%, Ag 80%, S 60%.

Jan 1, 2014

By R. A. Lowe

The low-shear viscosity of kaolin slurries is one of the principal characteristics that determines whether the clay can be utilized for paper and ceramic applications. In this work, causes of poor low-shear viscosity and methods of improving rheology have been investigated. The presence of fine-grained smectite impurities within the kaolin was shown to detrimentally affect the low-shear rheology of slurries produced from these clays. It was also shown that mechanically working (i.e., pugging) a crude kaolin followed by desliming to remove these impurities can reduce the low-shear viscosity.

Jan 1, 1998