Search Documents

By L. Alagha, O. Molatlhegi, S. Khatibi

"In the present study, the effect of organic/inorganic (hybrid) polyacrylamide polymer on fine coal flotation was investigated. Raw coal samples contain about 37% of ash-forming mineral at a feed size of -75 + 38 um were subjected to flotation tests in the presence of in-house synthesized hybrid Al(OH)3-PAM at different polymer dosages and pH values. Results show a significant improvement in both combustible recovery and ash rejection at 1 ppm polymer dosage. Further improvement of combustible recovery was obtained when flotation was performed at pH 5. Interfacial properties of coal particles before and after flotation were examined through electrokinetic (zeta potential) measurements of coal/water slurries. Zeta potential vs. pH curve were established and compared. In the case of raw coal/water slurry, zeta potential-pH curve resembles the ash-forming minerals (silica and clays) more than coal. After Al(OH)3-PAM-assisted flotation, the zeta potential of froth/water slurry shifted to more positive values point which strongly indicates significant removal of ash-forming minerals from coal by Al(OH)3-PAM. INTRODUCTION Coal has been a major commodity in meeting the world energy demand during the past several decades (Milici et al., 2013). According to the international energy agency, global coal demand will continue to increase for the coming decades. With increasing world population, the global electricity demand would also increase as more people would get access to basic electricity especially in developing countries (Maggio & Cacciola, 2012). Due to this increase in energy consumption, operations in coal mining and beneficiation processes have been highly mechanized to meet the demands. This mechanization has increased the quantity of raw fine coal particles produced which contain high amount of ash-forming mineral matter (slimes). Aplan et al., have reported that the major constituents of ash-forming minerals in U.S.A coal are clay minerals such as kaolinite, montmorillonite and illite (Aplan, 1997). Conventional froth flotation for fine coal cleaning suffers mainly from two major problems: 1) Low recovery of ultrafine coal particles due to slime coating by ash-forming minerals, and 2) The lack of selectivity, which results in the flotation of middlings and entrainment of mineral fines in the froth (Polat et al., 2003). Slime coating on both valuable and air bubbles have been proposed to explain the observed reduction in flotation recovery especially when fine grinding is required. In this case mineral matter may be degraded to extremely fine or colloidal sizes thereby creating difficulty in the water clarification process such as flotation. Slimes inhibit bubble-particle attachment, and increases reagent consumption due to the increase in solid/liquid interfacial area, resulting in low coal recovery."

Jan 1, 2015

By L. Dorador

"In block caving projects, the rock mass fragmentation process plays a controlling role in the design and success of the operation. Poorly understood, however, is the secondary fragmentation that occurs as blocks of caved ore move through the draw column and interact with one another. The initial size of these blocks can be considerable, as can their strength and stiffness as the presence of non-persistent joints and veining will be variable. Intuitively, more planes of weakness within the blocks should facilitate early fragmentation, but this assumption could depend on additional factors such as contact type between adjacent blocks and loads imposed through varying heights of the draw column. This paper reports the findings from a laboratory investigation examining the role of block strength and planes of weakness on secondary fragmentation. Testing was carried out on small-scale concrete cubes of uniform size, with and without embedded planes of weakness. The results obtained demonstrate the significance of veining and other planes of weakness on secondary fragmentation under one-dimensional compression, and allow for the development and constraint of empirical guidelines.INTRODUCTIONThe fragmentation process during block caving involves the initial (primary) fragmentation of rock in the cave back through stress-induced fracturing, release and fall of individual blocks onto the broken ore muck pile. This is followed by secondary fragmentation involving splitting and rounding of blocks as they move downwards through the draw column towards the draw point. The degree of secondary fragmentation achieved involves many variables related to the mechanical properties of the rock blocks as well as different operational factors. With respect to the block properties, the presence of planes of weakness in the form of veining and non-persistent joints is a topic of special interest given the significant influence it potentially has on the overall fragmentation process. However, the inherent heterogeneity and variable size of individual blocks generated from the cave back makes it difficult to develop any empirical relationships relating secondary fragmentation to compressive loading based on insitu observations and mine data. More preferable would be to keep constant block parameters, such as shape (aspect ratio and angularity) and size, through controlled laboratory testing. This work presents an efficient technique to fabricate concrete cubes in order to keep constant different block properties. These are then tested under one-dimensional compressive loading. The objective of these tests is to emulate a tight packing condition of single blocks such as that which would occur when the air gap between the cave back and broken ore in the draw column is small. When the air gap is small, detached blocks are unable to fall and rotate but instead maintain a very tidy arrangement with minimal voids left between adjacent blocks."

Jan 1, 2015

By T. S. Smith, C. C. Rennie

"THE LEAD-ZINC and tungsten mines of Canadian Exploration Ltd are on Iron Mountain, 8 miles south of Salmo, B.C., in the Nelson mining division. Relative location of the mines is shown on the general plan.First recorded lead production was in 1908 from surface outcrops. Small amounts of high lead ore were mined intermittently until 1926. No major lead-zinc production occurred until 1949 when outcroppings on the south side of the mountain were mined and diamond drilling began to prove the existence of a large replacement orebody. Lead-zinc ore has been mined continuously from the Jersey orebodies since March 1949, with monthly tonnage as high as 50,000 tons per month, but currently averaging 30,000 tons per month.Schee1ite-bearing tungsten ore was found in 1942 by H. Lakes in an old adit and open cuts at the north end of the Emerald tungsten orebody. The Emerald tungsten mine was developed by the Federal Government as a Wartime Metals project and operated for eight weeks in the fall of 1943, when the poor demand for tungsten closed the mine. Canadian Exploration Ltd. purchased the mine in 1947 and mined in excess of 100,000 tons in 1947-48 until the demand for tungsten dropped again and interest was centred on lead-zinc. The Federal Government repurchased and reopened the Emerald Mine in 195 L and built a new concentrator. The mine and mill were sold back to Canadian Exploration Ltd. in 1952.Regional Geology and IntrusivesThe host rock for both the lead-zinc and tungsten mineralization is the Laib formation of Lower Cambrian age, which consists of 400 feet of crystalline limestone underlain by beds of argillite, and argillaceous limestone locally altered to ""skarn"" or ""tactite"". The Laib limestone is overlain by black argillite and underlain by the Reno quartzite of Pre- cambrian age. Repetition of folded beds has allowed the interpretation of the large isoclinal fold which repeats the limestone (see general cross-section). Dolomitization and the associated lead-zinc ore have been found only in the right-side-up limestone and are not known in the overturned limestone.Two elongated stocks of granite cut the sediments. The Emerald stock outcrops along the east side of the Emerald tungsten mine and again west of the Jersey workings, while the Dodger stock outcrops only at the north end of the Iron Mountain. The shape and attitude of these bodies are believed to have been governed partly by pre-granite faulting and partly by pre-granite folding of the sediments. Although some forceful intrusion may have occurred the detailed granite surface indicates a gentle stoping emplacement."

Jan 1, 1949

By José Carlos do Amaral, Marcelo Groszownik, Jorge Beim

"Initiated in 2008, the project of this 1800 km long Electrical Transmission Line is a job of extreme technical complexity, crossing regions of major forests and rivers. When ready, it will allow the large Brazilian states of Amazonas, Amapá and Pará to use the energy from hydroelectric plants, thus eliminating the need for the use of diesel fuel thermal plants, with their much larger environmental footprint. Due to its extraordinary characteristics, the Green Peace and the Discovery Channel constantly visited the job. The part between the Amazon and the Xingu rivers started in 2012, and encompassed about 100 transmission towers with up to 150 m height, through a region known as “Alagados”. This region exhibits a 1.5 m water level during the rainy season, and soaked ground the rest of the year. Navigation of regular vessels is impossible during the flood season, when a dense vegetation called “bulhado” fills the riverbed, and vehicle traffic is impossible during the dry season, due to the extremely low surface soil resistance. Great logistical and technical difficulties were encountered for driving and determining the capacity of the piles. New systems had to be developed for driving the piles, with the simultaneous use of 15 small piling rigs. The final penetration, total number of hammer blows during driving, plus Dynamic and Static Load Tests were used for determining the driving and acceptance criteria.The geographical challenge and initial conditionsThis paper describes the execution of foundations for a 500 kV Electrical Transmission Line in a region that becomes flooded during the rainy season and heavily muddy during the dry season. This is the monsoon climate, typical of the equatorial region of Brazil, where there is a rainy season lasting for about half the year, followed by a very dry season. The temperature varies very little throughout the year, due to the proximity to the equator. The locals call the rainy season “winter” and the dry season “summer”.The most important part of the so-called “Alagados” region is situated inside an Environmental Extractive Reserve (RESEX) called “Verde para Sempre” (Forever Green), created in 2003. This is one of the largest environmental reserves in Brazil. It is an area controlled by the Brazilian Environmental Control Department, the Chico Mendes Institute (ICMBio). The environment control parameters are very strict.No deep foundation had ever been executed before along the “Alagados” region. The main challenge faced on this job, however, was working in a place where self-propelling vessels or land vehicles and equipment cannot be used. During the rainy season there is a dense and intricate vegetation called “bulhado”, which prevents the movement of outboard motor boats with propellers going deeper than 50 cm. In the dry season, the heavy mud prevents the movement of foundation equipment, excavators, trucks and other machinery."

Jan 1, 2015

By R. C. Gilmore, S. A. Lolon, G. E. Bogin, S. A. Saki, J. F. Brune, J. W. Grubb

"Gob ventilation boreholes (GVBs) are widely used in underground coal mines for longwall gob degasification purposes. GVBs are often drilled within 10 to 30 m above the top of the coal bed into the fractured zone, completed with 20 cm (8 in.) diameter casing and 60 m of slotted pipe at the bottom. The purpose of this completion strategy is to create a pressure sink to capture the emissions before they can enter into the underground workplace. For GVBs to work effectively, they must be drilled close enough to the working areas to capture methane from the fractured zone while the setting depth must be kept above the caved zone to minimize the amount of ventilation air that is drawn into the GVBs. Well completion parameters are important for creating safe working conditions. In this paper, computational fluid dynamics (CFD) studies will be presented to analyze the effect of different practices for GVBs completion parameters for methane extraction, formation of explosive gas zones in the gob and methane concentrations at the longwall face and tailgate. Authors have identified the optimum completion parameters for GVBs, which can maximize the benefit and minimize fire and explosion risk. INTRODUCTION Coal mines may be considered gassy based on the presence of CH4. Gas from the mined coalbed or from rider seams above or below the mined coalbed can migrate into the gob and then potentially move towards the working areas. In longwall coal mines with high methane emissions, sufficient ventilation and additional methane control measures are usually required to reduce the methane concentration in working areas to below statutory levels. Several techniques or combinations of techniques are available to control the methane hazard. These may include mine face ventilation to dilute methane, coal bed degasification, nitrogen injection into the gob to render a methane atmosphere inert and the use of gob ventilation boreholes (GVBs). Longwall face ventilation and dilution alone can only handle methane emissions up to a certain amount. When methane emissions exceed the face ventilation capacity, additional control measures are required. Drilling horizontal or vertical methane drainage holes into the coal seams as well as gob ventilation boreholes from the surface into the gob area to extract methane are common practices. GVBs are usually drilled from the surface above the longwall panel ahead of mining. When the face moves outby the GVBs and the gob begins to form, methane production starts from the boreholes. It is important to control the performance of GVBs to maintain a safe working environment in the mine. The performance of GVBs depends on multiple factors, including borehole location, length and diameter of slotted casing, setting depth of casing above the coal seam being mined, wellhead vacuum pressure, and permeability of caved-fractured zones."

Jan 1, 2016

By van der Merwem J. N.

"Coal pillars are prone to scaling over time, and are progressively reduced in size and consequently subjected to increased load and reduced strength. The effective factor of safety therefore reduces. Databases of failed and stable pillars cannot, therefore, be regarded as definitive.More than a decade has passed since the first attempt to predict the lifespan of pillars. This paper presents a review based on the new database and pillar strength equations. The methodology for the analysis is based on the fact that pillars scale. The ultimate safety factor (defined as the ratio between strength and load at the time of failure) is derived, followed by an estimate of the rate of pillar scaling, which results in an estimate of the expected time of failure.It is suggested that the predicted lifespan should not be used as an absolute indicator of expected pillar life, but rather as an index – the pillar life index (PLI) – to complement the safety factor and related probability of failure when evaluating pillar stability. A pillar with a predicted lifespan of less than 500 years would be regarded as being in danger of imminent collapse, while a lifespan of at least 1 000 years should be required for long-term purposes.The differences between this analysis and that published in 2003 constitute a strong case for regular reviews of all the empirically based stability indicators, namely the safety factor, probability of failure, and the PLI. Reviews at 10 year intervals appear to be required.The constants in the proposed method are valid only for the Witbank No. 1, 2 and 4 seams and the Highveld No. 2 and 4 seams.IntroductionIt is well known that over time, coal pillars are prone to scaling, and thus are progressively reduced in size and consequently subjected to increased load and reduced strength. The effective factor of safety therefore reduces and it is quite possible for failure to occur after a long time interval. In fact, scrutiny of the database of failed pillars indicates that failure occurred after periods ranging from 2 to 49 years, and not immediately after mining.The factor of safety for pillars at the time of failure is not the same as that immediately after mining. The concept of the safety factor is based on the pillar strength obtained by statistical analysis of pillar dimensions immediately, or within a month after mining, when the surveys are conducted. Strictly speaking, the safety factor as commonly used is valid only immediately after mining, and it continues to reduce thereafter. The ideal situation would be to base analyses of pillar strength on pillar dimensions at the time of failure, but that is simply not possible because the real dimensions cannot be measured at that time."

Jan 1, 2016

By F. B. Tough

An inusual job in controlling a gas well was executed on No. 1 well, Inland Oil and Refining Co., situated on the Alkali Butte structure, Freemont County, Wyoming. The work was done by the company in cooperation with the . S. Bureau of Minos, and resulted in a fuel saving of $5,000 in one season and of a repair job estimated at $15,000, or a total of $21,000. The woll had an open flow of 6,000,000 cubic feet of gas per day with a rock pressure of 560 pounds per square inch. A string of 6-1/4 inch casing with a toothed shoe was set on the cap rock above the gas sand at 2181 feet. Then the well was shut in, the gas worked out around both the 6-1/4 inch and 6-1/4 inch strings, breaking through the ground surface at several points under the derrick. Casing troubles encountered while drilling made it unsafe to attempt Coving the 6-1/4 inch string. Moreover, it was important from the standpoint of good management to make the gas from this well immediately available for fuel in other operations and, in addition, to save the gas from wasting. An ordinary mudding and cementing job would have necessitated sitting down this well for probably two months out of a very short operating season. For these rousons it was determined to mud the well, if possible, between the 6 and 8 inch strings by pumping mud fluid through the connection from the gas clamps. The gas clamps used wore of ordinary construction with a side outlet, making them equivalent to a Braden-hoad. When the mud fluid was pumped through the gas clamp into the space between the two strings, it began to appear inside the 6-1/4 inch string. It apparently entered the well either around the toothed shoe or through a "line sawed" leak in the string and was blown out of the well as fast as it was pumped in. In order to stop the leaks, about a half a gunny sack of finely chopped bull ropa was fed with the mud between the casings as before. The hemp gathered around the valves of the mud pump to some extent, and it also stuck in the casing-head fittings a few times. An obstruction in the casing- head would be removed by permitting the woll to "blow back" for a few seconds, and one in the pump valves, by removing the valves when necessary. In two days' time sufficient hemp and mud had been pumped into these strings to kill external and internal pressure. The wall was shut in and allowed to stand over night. The next day, by opening and closing the master gate at intervals,

Mar 1, 1921

By Yuanyuan Wang, Hong Li, Xueting Liu, Hao Bai, Kang Zhou

"Phase change materials are widely used in efficient utilization of energy and new energy technology. Especially, more attention has been paid to composite phase material, which is applied on architectural energy-saving and efficient working fluid. In this paper, stearic acid-silicon dioxide composite material was prepared by sol-gel process from tetraethyl orthosilicate (TEOS) and stearic acid (SA). The material was investigated by Field emission scanning electron microscopy (FE-SEM), Fourier transform infrared spectroscopy (FT-IR) and Differential scanning calorimeter (DSC). The FE-SEM results show that 3D-grids of silicon dioxide were formed clearly and SA was encapsulated in the silicon dioxide shell. The FT-IR results show that there were no chemical reactions between silicon dioxide and SA, which is the chemical property of the composite material, is stable. The DSC results show that the composite phase change material has favorable heat capacity. This material is expected to be used to make a cooling working fluid.1. IntroductionEnergy thermal storage becomes increasingly prominent issue in recent years, because thermal storage has been used in many aspects, for example, it can be added into building materials to improve heat conditioning. Another potential application of thermal storage materials is that the intermittent waste heat can be collected and recycled effectively by using the thermal storage facility. Thus, energy thermal storage plays a significant role in conserving available energy and improving its utilization [1]. Energy thermal storage includes sensible heat storage and latent heat storage. The latent heat storage has great heat density with a constant temperature during the phase change process [2-5]. Large quantities of latent heat storage will be absorbed and released when phase change takes place. Based on the former researches, some phase change material (PCM), such as fatty acid and paraffin waxes, has been proved to have high latent heat storage capacity and appropriate thermal properties [5-6]. However, using the PCM in energy storage systems directly is restricted, e.g. some properties of organic PCM, like form-stability and thermal conductivity, are not good enough to use. Meanwhile, almost all the inorganic PCMs are corrosive and most materials may cause sub cooling and segregation [7-9].The other problem is that the leakage when the temperature reaches the phase change point. Therefore, encapsulated composite phase change material (CPCM) emerged in order to solve the problem of leaking out, minimize the sub cooling and prevent phase segregation. [10-13] However, the easy flammability of fatty acid also has hindered the development of PCM. Accordingly, it has been found out that silicon compounds are environmentally friendly promising substitutes for halogen-containing flame retardants. Especially, silsesquioxanes are excellent in the flame retardancy. So CPCM can be encapsulated with SiO2 acting supporting material."

Jan 1, 2014

By M. J. Ankeny, J. J. Forbes

"One of the main functions of the U. S. Bureau of Mines, as authorized by Congress, is to investigate safety and health conditions, to disseminate information regarding safe and unsafe practices in mining, and to aid in improving safety and health conditions of mining communities and in promoting the welfare of the miner. Among several methods of reaching the miner and interesting him in safety work, perhaps the most effective is through the 11 mine safety stations and 11 railroad cars known as mine rescue, or more correctly, mine safety cars.Frequently, the Bureau of Mines receives requests for information regarding the purpose, equipment, personnel, and construction of its safety cars used in the field service. It is the intention of this circular to present to the mining public in particular, and to the public in general, some definite information regarding these safety cars and their functions.The cars are operated throughout the mining fields of the United States and are headquartered as follows (see fig. 1): Car 1, Reno, Nev.; Car 2, Raton, N. M.; Car 3, Pittsburgh, Pa.; Car 4, Terre Haute, Ind.; Car 5, Pineville, Ky.; Car 6, Pittsburg, Kans.; Car 7, Huntington, W. Va.; Car 8, Duluth, Minn.; Car 9, Butte, Mont.; Car 10, Des Moines, Iowa; Car 11, Anchorage, Alaska.One of the most important purposes of the U. S. Bureau of Mines safety cars is to render service at mine fires and explosions where human life is endangered. State mine inspectors and other interested persons are supplied with itineraries of the car operating in their districts from time to time, so that they may know at all times where the car can be found in case of emergency. When these disasters occur the car may be reached direct or through its field headquarters, and upon receiving word of a mine disaster, or request for assistance, it immediately proceeds to the scene of trouble. Frequently a special locomotive is supplied by the railroads and in many instances the movement of the car is given the right of way over all other railway traffic. Upon reaching the destination, the facilities and personnel of the car are immediately available for rescue and recovery operations.Following most mine disasters a thorough investigation is made by engineers of the Bureau of Mines, and a confidential report is submitted to the operator. The information gained in this manner from a large number of mine fires and explosions, together with the knowledge gained from the experimental work carried on at the Experimental mine of the bureau at Bruceton, Pa., serves as a basis upon which the bureau is able to recommend preventive measures whereby similar occurrences may be averted. The bureau car is often used as headquarters for the investigating engineer when such an examination is being made."

Mar 1, 1931

By Robert Sturk, Knut O. Halvorsen

"INTRODUCTION AND BACKGROUND The world needs visionary people to break new ground and bring development forward. The human race has an inherent power and lust to explore and push borders, but also to connect and bring people together. Transport of people and goods has through history been a key factor to develop societies and increase collaboration between people and regions. Today, in the era of globalization, efficient transport systems are still vital for further development. Often, ideas of bold projects, like long bridges or tunnels, have been raised long before those projects are realized and actually built. This shows that visions must gradually be transformed into feasible business cases and sustainable political solutions. In some cases also technological development is necessary to make visions come true. Isambard Kingdom Brunel, indeed a visionary engineer, completed the oldest underwater tunnel in the world when the Thames Tunnel in London was opened in 1843. This tunnel is still in operation and now part of London’s rail transport system. Another milestone for the tunnelling industry was passed when the 54 km long Seikan tunnel in Japan was opened in 1988 after more than 15 years of construction. This tunnel is presently the world’s longest railway tunnel. Together with the 50.5 km long Channel tunnel between the UK and France, which has the longest undersea portion 37.9 km, they constitute examples of pioneering engineering projects that bring the industry forward. In 2016, the Gotthard Base Tunnel will be opened and then becomes the longest railway tunnel in the world with its 57.1 km. The trend is obvious that tunnels throughout the world are getting longer and longer. The Brenner Basis Tunnel presently under construction will yet again break the record being 64 km long. Presently, a number of even longer tunnels are planned and under design, some of these also have very long subsea portions, e.g. Bohai Straight Tunnel (123 km), Irish Sea Tunnel (around 100 km) and the Helsinki – Tallin fixed link (approximately 90 km). Northern Europe sees an increasing demand on efficient transport corridors to meet the growth of freight transportation between the Scandinavian Peninsula and central-Eastern Europe. Sustainable solutions will be required, and a shift from road/maritime transports to rail is imperative. Consequently, this paper describes yet another visionary project, a fixed railway link between Sweden and Germany, the Shortcut, to enhance traffic between these regions and to make it greener. It is true that this project still requires some work from politicians, economists and engineers to be realized, however, building a 100 km long tunnel under the Baltic Sea may become reality sooner than we think."

Jan 1, 2016

By Michael Arnold

"BAUER Foundation Corp. was one of three contractors awarded with the installation of a cut-off wall at the Herbert Hoover Dike Rehabilitation project. The cut-off wall was constructed up to 84 feet deep and 25 inches thick. It extended from the crest through the middle of the existing dike into the underlying peat, sand, and rock layers. BAUER used the cement deep soil mixing method of Cutter Soil Mixing (CSM) to install the wall. Soil mixing was facilitated by first removing the peat layer in the wall alignment using Kelly drilling and replacing it with suitable backfill, resulting in a secant pile wall arrangement of replacement columns. BAUER successfully finished four task orders with a total length of just over 10 miles. Up to six rigs of the types BAUER BG 28, BAUER BG 40 and RTG RG 25 were concurrently used to perform the replacement columns and the cut-off wall installation.The paper introduces the project, the geotechnical site conditions, and the requirements specified by USACE. It focuses on the specific adaptation of the CSM method to the site conditions and on the equipment used. Strength and permeability results obtained from an extensive testing program are presented. The impact of the curing conditions on lab and in-situ test results is studied, and test results are related to soil conditions.PROJECTThe Herbert Hoover Dike is a 143-mile-long dike encircling Lake Okeechobee in south central Florida. When it was constructed in the 1930s and 1960s, the purpose of Herbert Hoover Dike was flood protection from hurricanes. However, during the 1970s a higher lake level was maintained permanently to provide local agriculture with water. Later, damage became apparent during two nearly back-to-back high water events in the 1990s, when numerous sink holes, seeps, pipes, and boils were observed (Fig. 1). In 2000, the Congress approved USACE to propose rehabilitation measures. The installation of a cut-off wall into the existing dike was chosen during the initial design process as the preferred measure to improve the safety of the dike (Davis et al. 2009).The first section of the dike to be rehabilitated was Reach 1 located along the southeast side of the lake between the towns of Port Mayaca and Belle Glade. An indefinite delivery indefinite quantity (IDIQ) multiple award task order contract (MATOC) was issued for this 22.4-mile-long stretch by USACE in 2007. BAUER Foundation Corp. (BAUER) was one of the three contractors that succeeded in the qualification process. Each of the three successful contractors had their own novel construction techniques. In the years 2008 to 2012 BAUER executed four task orders totaling over 10.0 lineal miles of cut-off wall with 3.3 million square feet of design surface area."

Jan 1, 2015

By Armin W. Stuedlein, Jim Zammataro, Bernie Hertlein, Daniel Belardo, Qiang Li, Antonio Marinucci

"An experimental program focusing on four drilled shafts was conducted to determine the effect of high strength steel reinforcement bars on lateral resistance, steel casing on axial and lateral resistance, and steel casing without internal reinforcement on lateral resistance. Thermal Integrity Profiling (TIP) Thermal Wires and crosshole sonic logging (CSL) access tubes were installed in each shaft, and thereafter the corresponding non-destructive testing (NDT) was performed on each shaft to assess the integrity of the shafts and to compare the results from the different NDT methods. The results of the CSL tests using scored PVC tubes are compared against those conducted in 73/56 fully-threaded steel hollow bars, whereby the results indicated that the threaded bars served as a good host for performing the CSL tests. The data from the TIP Thermal Wires is compared against the results from the CSL tests for each of the four shafts, and the similarities and discrepancies between the two methods are discussed. This paper will serve as a reference to those interpreting the measurements and data obtained by performing nondestructive integrity tests on drilled foundations.INTRODUCTIONNon-destructive tests (NDTs) embody a set of critical tools for the evaluation of the integrity of constructed deep foundations, particularly for cast-in-place foundation elements. Construction defects may require the rejection of the foundation element by the owner’s representative, resulting in costly repairs or replacements and delays to the project schedule. The use and appropriate interpretation of the results from the NDTs provide the information required when evaluating the integrity of these constructed elements. A cooperative research program was conducted to assess the effects of various construction variables on the axial and lateral performance of drilled shaft foundations, which provided an opportunity to compare the established Crosshole Sonic Logging (CSL) test method to the newer Thermal Integrity Profiling (TIP) Thermal Wire method. This paper presents an overview of the experimental program performed at the geotechnical test site at Oregon State University (OSU), details of the CSL and TIP installation and testing methods, and the results of the NDTs on the constructed drilled shafts. Because one of the shafts was constructed with fully-threaded longitudinal steel hollow bars, this experimental program also allowed the assessment of the use of the hollow bars as access tubes for the CSL tests. Both the CSL and TIP test methods indicated that the shafts were of good quality and free from defects or anomalies; the data obtained using the TIP method also provided an estimate of the as-constructed shaft diameter and the reinforcement cage alignment, which will prove helpful when back-calculating axial and lateral load transfer during future loading tests."

Jan 1, 2016

By D. Kidd, T. Tucker, L. M. Indergard, S. Davis

"INTRODUCTION The Lisbon Valley Mining Co LLC (LVMC) operates the Lisbon Valley Mine located in SE Utah. The mine includes 3 open pits, 150-acre heap leach pad, and solvent extraction electro winning plant (SX/EW). Approximately 25MM tons of ore has been mined since 2005. The ore is stacked on the leach pad to an average height of 55 feet and occurs as a blend of crushed material (minus 2”) and run-of-mine (minus 24”). The host rocks include Dakota and Burro Canyon Sandstones. Copper occurs finely disseminated in this material at an average grade of 0.46%. Minerology is 63% sulfide, 27% oxide, and 10% insoluble. Total inventory mined through 2016 is approximately 230 MM lbs. METALLURGICAL CONSTRAINTS Copper production is constrained by areas of low permeability ore and geochemical issues, including acid consumption. The intrinsic permeability the ore ranges from 10-2 to 1 Darcy. This permeability does not permit sufficient aeration by natural convection, therefore oxygen transport is largely limited to the mass of oxygen that can remain dissolved in leachates. As a result, greater than 50MM lbs of copper remains in inventory and occurs secondary sulfides, including chalcocite, covellite, and bornite. BIOLEACHING FUNDAMENTALS Due to the higher activation energies of secondary sulfides, notably covellite and bornite, a strong oxidant is needed to remove an electron from the metal-sulfide lattice and release the copper cation into the sulfate solution. This process occurs most efficiently using the strong oxidant ferric iron (Fe3+). Ferrous iron can be oxidized to ferric iron by oxygen via chemical oxidation or biologically; which was measured to occur 500,000 times faster when using microbes versus oxygen.1 The microbes that oxidize ferrous iron (Fe2+) to ferric iron are naturally abundant and will develop biomass when appropriate conditions and nutrients present themselves. Most nutrients are provided by the ore/irrigation (P,N,Mg, Ca & Fe2+) while the others (O2 and CO2) are provided by air. In most cases, oxygen transfer is the rate limiting step during copper sulfide leaching. 1 Lacey & Lawson 1970 FORCED AERATION SYSTEM DESIGN This paper describes LVMC’s efforts to bioleach the remaining inventory by forced aeration. Two basic aeration systems were installed and tested including vertical wells and horizontal piping. Vertical System The vertical system was installed using the mine’s blast hole drilling rig. Wells were constructed using 4” high-density polyethylene (HDPE) connected to 4” polyvinyl chloride (PVC) screens similar to conventional bioventing wells. Ore samples were collected at each well location to characterize the spatial distribution of the remaining inventory along with fines (minus 200 sieve), pH (acid consumption), and iron. A block model of each analyte was developed and mapped in 3D."

Jan 1, 2017

"The mountains of Utah contain one of the largest deposits of high grade bituminous coal in the world. According to the United States Geological Survey, there are 13,130 square miles of land known to contain workable coal, and these extensive fields contain 196,000,000,000 tons of coal. More remarkable than the extent of the coal fields is the thickness of the coal beds. Over three-fourths of the output of coal in Utah is recovered from beds ranging from 8 to 17 feet in thickness, as compared to one-eighth of the output of the entire country from such beds. In 1917, Utah mined one-third of its coal from seams at least 16 feet thick, compared to one-half of one per cent of the total bituminous output of the country from like seams.Coal at Wales, in Sanpete County, and in the vicinity of Coalville, Utah, was, it is reported, the first discovered by white men in the state. Wales claims the distinction of having produced the first coal mined in Utah. Two men, who had been coal miners in Wales, learned of the coal from an old Indian chief who called it ""rock that would burn."" In 1857, the town of Wales was founded and coal mined, and in 1858 some coke was manufactured and hauled by ox team to Salt Lake City. South of Wales is Castle Valley, in Wasatch Plateau field. From 50 to 60 miles of the Old Spanish Trail from Santa Fe, New Mexico, to Monterey, California, lies in Castle Valley. The coal in this field may or may not have been known at the time the trail was used extensively. The first published reference to this coal, however, was made by a party of the Corps of Topographic Engineers in their journal for October 11, 1853.After the completion of the Union Pacific railroad in 1869, mining on a commercial scale was attempted. In 1876 the Utah and Pleasant Valley railroad commenced operations between Scofield, in Carbon county, and Springville, Utah county, and following the year 1878, when the Rio Grande Western railway began construction through the Carbon county field, development increased until in 1900, when large smelters commenced operations in Salt Lake valley and gave coal mining in Utah an impetus that first carried it to an annual output of a million tons. During the past fifteen years many new mines have been opened, and with the construction of the Utah railway, an exclusive coal road, from the properties of the United States Fuel company in Carbon and Emery counties to connect with the Union Pacific system at Provo, the state reached a maximum production of 6,005, l 99 tons in 1920."

Jan 1, 1925

COLLECTIVE bargaining, hereto-fore loudly proclaimed as one of the stout timbers of the Republic, has passed from the picture. The coup de gr[a]ce was struck by the President of the United States when he ignored his vested legal prerogative and seized the steel industry by the dubious authority of, his "inherent powers." Autocratic judgment by a single official replaced arbitration by the steel industry and labor union. This is the outcome of a battle which has been bitterly waged for months in the hazy atmosphere created by well oiled propaganda machines. Prior to government intervention, there was no clear picture of the issues at stake. All parties concerned marshalled their accountants to conjure up figures proving their respective contentions. The results were fed into public relations departments for embellishment and dissemination. Thus, the public was asked to believe on one hand, that the steel worker, who is second only to the coal miner in hourly wages, was entitled to an increase in pay and other benefits. Nothing was said about the effect-of such an increase on the national economy. Industry in turn pointed to declining profits after taxes, but failed to mention the more than a billion dollars spent on plant expansion, in addition to the payment of substantial dividends for 1951. With the intervention of the administration, the immediate issue became clear to freedom-loving Americans. Is the executive branch of the government above the law, or is it supposed to uphold and carry out the .laws of Congress? The present administration forgot that it is a servant of the public and has become despotic. The American people must obliterate this dangerous precedent which has been set by the administration or accept the. ominous consequences of submission. Fortunately, the strongest weapon of the citizen-the ballot -still remains. When democratic procedure is restored, stabilization of the economy will continue to challenge us. This is the main public stake in the steel controversy. Only a solution based on bed-rock democracy will work. If the emergency is real, and we must assume that it is, this is the time for sacrifice. Industry and labor must meet without rancor to resolve wage contracts through collective bargaining. The government role, under emergency conditions, must be to objectively maintain wage, and price ceilings in the interest of stabilization. Political expediency cannot be permitted to' influence these controls. Politics and not the public weal have been the guide lines for too long. We are at the cross roads. By all sober judgment, this is the time for Americans to take a militant interest in their government today. Tomorrow will be too late.

Jan 1, 1952

By Francis B. Foley

Fundamentally, slag control in acid open-hearth steelmaking cannot be considered from any different viewpoint than can that in basic open-hearth melting. The same laws of mass action and distribution apply in both cases, so that while most, if not all, of the recent intensive study of slag-metal reactions have been carried on in basic furnaces the principles evolved are nevertheless applicable to acid open-hearth steelmaking and it is therefore not our intention to discuss the various possible chemical reactions in the slag and between slag and metal. The points we have to carry in mind, in considering acid melting practice, are the differences in the type of steels produced and the difference in the chemistry of both the steel and the slag. The acid furnace is used to produce, let us not say "quality" steel, for, after all, a "quality" steel for one purpose is not a "quality" steel for another, but steels that require acid melting practice to be of proper "quality." Steels that are required to have high physical properties in tests taken transversely from forgings are peculiarly the product of acid furnaces. In this class may be placed various ordnance materials, notably gun forgings and projectiles and large commercial forgings requiring high transverse ductility. Forgings requiring an extremely hard surface, polished and free from imperfections, are also typical acid-steel products. Of course, such forgings can be made of basic open-hearth steel, but not with the same assurance of success. At the start, the preparation of the slag in the acid and basic furnaces differs. Lime is charged in the beginning of a basic heat to form a slag, but in the acid furnace nothing is added for the special purpose of producing a slag when the heat is melted down. The result is that the acid furnace has much less volume of slag than the basic. The slag formed upon melting down is made up almost entirely of the oxides of elements contained in the metallic charge, notably oxides of iron, manganese and silicon, the amount of silica being augmented somewhat by erosion of the furnace lining. A typical acid open-hearth slag, when the bath is completely melted, will have an analysis about as follows: CaO, 3.40 per cent; SiO2, 51.9; Fe2O3, 1.25 ; FeO, 28.86; Al2o3, 1.82; MnO, 12.22. The high iron oxide content of the slag gives it a black appearance. The metal is high in carbon and some manganese and silicon will be present, depending on the amount in the original charge, the amount of

Jan 1, 1935

By Francis B. Foley

Fundamentally, slag control in acid open-hearth steelmaking cannot be considered from any different viewpoint than can that in basic open-hearth melting. The same laws of mass action and distribution apply in both cases, so that while most, if not all, of the recent intensive study of slag-metal reactions have been carried on in basic furnaces the principles evolved are nevertheless applicable to acid open-hearth steelmaking and it is therefore not our intention to discuss the various possible chemical reactions in the slag and between slag and metal. The points we have to carry in mind, in considering acid melting practice, are the differences in the type of steels produced and the difference in the chemistry of both the steel and the slag. The acid furnace is used to produce, let us not say "quality" steel, for, after all, a "quality" steel for one purpose is not a "quality" steel for another, but steels that require acid melting practice to be of proper "quality." Steels that are required to have high physical properties in tests taken transversely from forgings are peculiarly the product of acid furnaces. In this class may be placed various ordnance materials, notably gun forgings and projectiles and large commercial forgings requiring high transverse ductility. Forgings requiring an extremely hard surface, polished and free from imperfections, are also typical acid-steel products. Of course, such forgings can be made of basic open-hearth steel, but not with the same assurance of success. At the start, the preparation of the slag in the acid and basic furnaces differs. Lime is charged in the beginning of a basic heat to form a slag, but in the acid furnace nothing is added for the special purpose of producing a slag when the heat is melted down. The result is that the acid furnace has much less volume of slag than the basic. The slag formed upon melting down is made up almost entirely of the oxides of elements contained in the metallic charge, notably oxides of iron, manganese and silicon, the amount of silica being augmented somewhat by erosion of the furnace lining. A typical acid open-hearth slag, when the bath is completely melted, will have an analysis about as follows: CaO, 3.40 per cent; SiO2, 51.9; Fe2O3, 1.25 ; FeO, 28.86; Al2o3, 1.82; MnO, 12.22. The high iron oxide content of the slag gives it a black appearance. The metal is high in carbon and some manganese and silicon will be present, depending on the amount in the original charge, the amount of

Jan 1, 1935

By C. M. Moncrief, B C. Craft

A bentonite-clay drilling mud when treated with tetrasodium pyroarsenate underwent substantially the same reduction in viscosity and water loss as when treated with the complex phosphates. The complex arsenate showed a slightly higher reversion after heating; the other arsenates showed poor viscosity-reducing properties. Introduction During the past 10 years the chemical control of drilling mud has become of major importance in affecting the successful drilling and working over of wells. The desired properties of drilling mud have been well established, and in obtaining these characteristics there has developed a large market for viscosity-reducing chemicals. Viscosity reduction produced by humic acid, tannic acid, sodium silicate, sodium tannate, Calgon, and the complex phosphates has been described by Loomis, Ford, and Fidiam.l The effects Of treatment with complex phosphates and ammonium PolyPhosPhates on the rheological properties of muds were investigated by Fancher2 and the alkali vanadates have been described by Williams.3 Laboratory Investigations It is the purpose of this paper to point out the effects of arsenates in controlling the viscosity and gelling characteristics of a drilling mud. Viscosities and gel strengths were measured at room temperatures with a Stormer viscosimeter calibrated in centipoises and operated at 600 r.p.m. Water loss was determined at 80°F. with the Baroid low-pressure wall-building tester at a pressure of I00 lb. per sq. in. for 30 min. The hydrogen-ion concentration was measured with a glass electrode. The bentonite-clay suspensions were prepared in the laboratory and allowed to age several days before testing. Members of the Arsenic Group in the periodic Table include arsenic, antimony and bismuth, but this investigation was limited to arsenic. Phosphorus also occurs in Group V of the Periodic system and phosphorus and arsenic form many closely related compounds such as pH3 and AsH3, P2O5 and As2O5, H3PO4 and H3AS04 Samples of tetrasodium pyroarsenate were prepared by fusing c.p. disodium arsenate (Na2HA5O4.7H2O). According to Friend,' this re-forms the ortho-arsenate on dissolution in water. Sodium trihydrodiorthoarsenate was prepared as described by Mellor,5 from arsenic pen-toxide as follows: As2O5 + 3H20 -> 2H3AsO4 2H3AS04 + 3NaOH Na3H3(AsO4)2 .3H20 Sodium dihydrogen orthoarsenateWaHz-As04) was obtained by fusing together equivalent quantities of arsenious Oxide and sodium nitrate, dissolving the residue in water and allowing it to crystallize.

Jan 1, 1946

To determine the relative permeability of the soil a series of percolation tests were performed at the three locations of interest at Lanse, i.e., 3C, 03A and strip bank, and KA and KB at Kato. Soil cores were removed to 2, 8, 16, 24 and 32 inch depths with the thin wall sampler tube, each core separated from the next by about fifteen feet. Then two-foot-long thin-wall tubes were inserted into the 2, 8, and 16 inch deep holes and three-foot long tubes were inserted into the 24 and 36 inch deep holes. Each tube was tamped down about one inch further to assure a bottom seal; the tubes were filled with water and the rate of fall was measured. The test is similar to those done for septic tank percolation studies 6; but is not quantitatively related to Darcy's coefficient of hydraulic conductivity because the water can flow in three dimensions from the bottom of the tube. The measurements are dependent on the length of test, since the rate of fall is a function of the head. Therefore, it should be noted that the 24 and 32 inch deep tubes should give faster percolation rates because of the one foot greater head. At locations 03A and 3C the data show a sharp decrease in percolation at increasing depth, Table XV. However, the percolation at 03A and 32 inch depth is much higher than at 3C (0.2 vs. 0.01 inches/hour); the fragipan layer must be deeper at the 3C location since this area does experience a perched water table. On the strip bank the rates of falling head are randomly variable, appearing to be as much dependent on the particular location of insertion as on depth of placement. For example, water drained from the 16 inch tube as fast as it was added, probably into a sub-surface cavity or crevice. At Kato the tubes were more difficult to place because of interference of tree roots. For this reason 2 inch deep tubes were not inserted. These short tests at Kato were inconclusive, varying extensively when the tubes were moved. Field permeability tests were also performed in two (previously described) eight-inch diameter permeater tubes at Lanse and one at Kato. Because the soil is confined inside the tube, hydraulic conductivity can be calculated according to Darcy's flow equation. The high values reported in Table XVI experienced when the tubes were rewetted from a dry surface condition, enable us to conclude that infiltration is faster than the saturated permeability of the soil. In contrast to the falling head percolation tests, these permeability results do not show a high variation between locations.

Jan 1, 1972

By Marsh S. Watson, Robert A. Howard

The effect of depth of formation penetration by casing perforations has been studied by means of an electrolytic model. It is found that the relative productivity of perforated casing is profoundly affected by the depth to which the formation is penetrated. The first in. of penetration i: of especial importance. A scaling equation which was shown to agree with experimental results at zero penetration is used to calculate the relative productivity of a waled down casing with scaled down perforations. INTRODUCTION In an earlier piper' the authors showed that the point sink representation of casing perforations is inade- quate. It was Pointed out at that time that while the electrolytic model results were a marked improvement over point-sink calculations, they still left a great deal to be desired in that the electrolytic model represented a case not realizable in practice, namely, a clean hole through the casing but undisturbed formation on the other side of the casing. Obviously, to be effective, the perforation must penetrate a finite distance into the producing formation. It was the purpose of the present investigation to find how the relative productivity of perforated casing varies with depth of penetration. The term "depth of penetration" as used in this paper refers to the distance which the perforation penetrates the producing formation. The amount of casing and cement penetrated is not taken into account, a fact which is discussed more fully later. The "casing radius," therefore, is to be interpreted as the radius of the boundary between cement and formation wall. in cases where the casing is not in contact with the formation wall. APPARATUS The electrolytic model experimental setup was identical with that described in the previous paper' except that the platinum electrodes were now allowed to project from the lucite cylinder by varying amounts. When fewer than eight electrodes were used, the unused ones were covered with a coat of insulating material to minimize disturbances to the current flow-lines. Comparison runs made with the unused electrodes uninsulated, however, showed that the values of Q/Q0 so obtained did not vary by more than the experimental error from the values obtained with the unused electrodes insulated RESULTS The variation of relative productivity* with perforation density is shown for various penetration depths from 0 to 4.03 in. in Fig. 1. It will be seen that even one in. of penetration into the formation results in a huge increase in the relative productivity. Moreover, as-the depth of penetration increases, it becomes less and less advantageous to use large perforation densities, 80 pel. cent of open hole productivity being obtained with only three 0.5-in. diameter holes per foot when the penetration is 4.03 in.

Jan 1, 1950