Search Documents

By Clarence O. Babcock

In this report, the Bureau of Mines presents a method for reducing the complexity of designing room-and-pillar mining systems by treating them as anisotropic soft inclusions in the surrounding ore or host rock. Theoretical models were derived for the calculation of the effective Young's moduli for these systems. The predicted behavior of the plate-type elements used in these models agreed well with test results from 21 plates each with 49 holes spaced on a 7 X 7 Cartesian grid. The plates behaved as anisotropic solids, the effective Young's moduli of which could be predicted from the scaled hole size and spacing. Actual hole shape was insignificant. The effective Young's moduli for simple mining systems are calculated in sample problems. This approach should provide information about field stress in the mining region and the stress distribution in the surrounding ore or host rock when the actual mining configuration is replaced by an anisotropic inclusion in a finite element analysis. The field stress within the inclusion can then be applied to the actual opening shape to determine the stress distribution within the mining region.

Jan 1, 1970

By Sheng Zhang

The compressive strength of coal in Yanlong mine area of China is less than 3 MPa. Basically, it is powdery. The roof and floor rocks are mudstone. Therefore this coal seam is a typical ?three soft? coal seam. Roof bolting cannot be used due to the very soft strata. When the conventional U-steel support was used, roadways deformation exceeded 30% of its original dimensions in some sections one half month after development. The required repair work was huge, seriously affecting the daily mine production. This paper describes how to support the soft coal roadways. The deformation characteristics of soft coal roadway were investigated. The conventional U-steel support is not subjected to uniform load, so the whole supporting structure must be strengthened. In addition, drilling holes in the coal seam can transfer high stress from near the ribs to the deeper parts of the surrounding strata, which is beneficial to the stability of the roadway. This new support method is to combine the strengthened U-steel support with pressure-relieving drill holes, providing an economic and efficient way to support the very soft coal roadways.

Jan 1, 2013

By C. Pritchard

John Marks said in his acceptance of the Hartman Award in 2008, "I guess that without the occasional complaint, your mine is probably over-ventilated" (Marks, 2008). Miners are seldom in this situation and spend much of the time trying to find enough air to keep an operation running. With examination, there are usually changes that can be made to increase the efficiency of ventilation systems. Mine ventilation air is a costly commodity, especially by the time it has been heated or cooled and moved to the bottom of the shaft and through the mine airways. Modifications that result in surplus mine ventilation air could bring financial and environmental benefits. Some issues mine operators have needed to address recently are increased airflow requirements to dilute diesel particulates in metal and nonmetal mines, to ventilate reserves that are deeper, hotter, and further away from fans and shafts, and to meet demands from increased production. This paper discusses successful methods to find additional usable air when there is no extra ventilation capacity. Most of the options presented in this paper are useful for metal/ nonmetal operations but some may be applicable to coal as well.

Jan 1, 2010

By J. H. Rowland, R. A. Thomas, III, C. D. Litton

Atmospheric monitoring systems (AMS) are required when using air from conveyor belt entries to ventilate working sections in U.S. underground coal mines. AMS technology has the potential to increase fire safety mine-wide, but research is needed to determine the detection and response times for fires of a variety of combustible materials. To evaluate the potential of an AMS for fire detection in other areas of a coal mine, a series of full-scale fire experiments were conducted to determine detection and response times from fires of different combustible materials that are found in U.S. underground coal mines, including high- and low-volatility coals, conveyor belts, brattice materials, different types of wood, diesel fuel, and a foam sealant. These experiments were conducted in the Safety Research Coal Mine (SRCM) of the U.S. National Institute for Occupational Safety and Health (NIOSH) located in Pittsburgh, PA, using a commercially available AMS that is typical of current technology. The results showed that through proper selection of sensors and their locations, a mine-wide AMS can provide sufficient early fire warning times and improve the health and safety of miners.

Jan 1, 2016

By C. Pritchard

John Marks said in his acceptance of the Hartman Award in 2008, “I guess that without the occasional complaint, your mine is probably over-ventilated” (Marks, 2008). Miners are seldom in this situation and spend much of the time trying to find enough air to keep an operation running. With examination, there are usually changes that can be made to increase the efficiency of ventilation systems. Mine ventilation air is a costly commodity, especially by the time it has been heated or cooled and moved to the bottom of the shaft and through the mine airways. Modifications that result in surplus mine ventilation air could bring financial and environmental benefits. Some issues mine operators have needed to address recently are increased airflow requirements to dilute diesel particulates in metal and nonmetal mines, to ventilate reserves that are deeper, hotter, and further away from fans and shafts, and to meet demands from increased production. This paper discusses successful methods to find additional usable air when there is no extra ventilation capacity. Most of the options presented in this paper are useful for metal/ nonmetal operations but some may be applicable to coal as well.

Jan 1, 2009

By Kazuteru Tozcwa

The oxidation of several sulfide minerals in aqueous ammoniacal solution is discussed thermodynamically. The region in which Cu(NH3)2 4+ is stable has been estimated as a function of pH and concentration of total ammonia, {[NH3) + [NH4)}. In ammonia leaching when copper in sulfides is assumed to be extracted in the form of Cu(NH3)2 which will be rapidly converted to cupric ammine, thermodynamic data predict that such minerals are oxidized readily in the following order, CuS, Cu2S, CuFeS2, ZnS, NiS, Ag2S. This agrees with investigations on ammonia leaching of sulfide minerals, reported previously. The leaching of copper sulfide concentrate has been examined experimentally. Copper in a copper sulfide concentrate, in which the main constituents were chalcopyrite and pyrite, was effective¬ly extracted. The copper extraction was affected by factors such as (1) agitation intensity, (2) oxygen partial pressure, (3) NH3/Cu molar ratio, (4) leaching temperature and (5) addition of ammonium sulfate. From the results obtained in this work, it is concluded that mass transfer of oxygen plays the most important role in ammonia leaching of copper sulfide minerals.

Jan 1, 1976

By I. C. Edwards, E. O. Lilge, H. H. Mccreedy

"Introductory and GeneralTHE DRIESSEN CONE bas been used fairly extensively commercially as a classifier. Its use as a concentrator in the upgrading of ores at a fairly high ratio of concentration with concomitant recoveries has been almost negligible. Certain known features about the cone, however, such as its high throughput capacity, cheapness of construction and operation, and simplicity of design have attracted the attention of mill men. An inadequate knowledge of the operating characteristics of the cone when used as a concentrator seems to have been the main reason for its lack of use. It was for this reason that the present investigations§ were undertaken to determine the operating characteristics of the cone and its application to the concentration of uranium ores, with particular emphasis being placed on the concentration of low-grade uranium ores.The investigations were started in December, 1951, and have continued uninterrupted to the present. The initial work was confined chiefly to investigating the operating characteristics of the cone in order to establish the trends that certain variables would exert on the general metallurgy of uranium concentration. Optimum metallurgy was therefore not the prime initial objective."

Jan 1, 1955

By Mikiya Tanaka

Keywords: Solvent extraction, nickel, electroless plating, accelerating effect With the increasing importance of electroless nickel plating technology in many fields such as the electronic and automobile industries, the treatment of spent baths is becoming a serious problem. Although the spent baths are currently treated by a conventional precipitation method, a method with no sludge generation is desired. Previously, we proposed the solvent extraction recovery of nickel from the spent baths by means of solvent extraction using LIX84I as the extractant. However, a problem of this method was that the extraction and stripping of nickel were not fast enough to achieve high efficiencies when the continuous extractor was used. We have overcome this difficulty by finding that the addition of an acidic organophosphorous reagent in small amount into the organic phase markedly promotes the extraction and stripping rates of the nickel. Shaking-out tests using a separatory funnel at 240 spm revealed that the time to reach the equilibria is more than 60 min with only 20 vol% LIX84I, but is reduced to 10 min and 2.5 min by adding 2 vol% DP8R, respectively, during the extraction and the stripping with sulfuric acid.

Jan 1, 2004

By Henry M. Harris

Low-carbon shales from 65 deposits and 11 sources of coal-mine waste in western Oregon and Washington were tested in a rotary kiln for their suitability as raw material for expanded aggregate. Shales from 41 sources bloated enough to produce crushed, expanded aggregates, weighing less than 65 pounds per cubic foot in the preliminary tests. The samples were judged on the basis of processing qualities, physical properties, and size and uniformity of the source. Nine low-carbon shale deposits and three coal-mine waste sources were selected for more extensive bloating tests and for examination of the expanded aggregates in concrete shapes. Composite samples from these 12 sources and from 2 commercial operations, when processed for testing in concrete shapes, had bulk densities ranging from 37.S to 72.9 pounds per cubic foot. Damp-cured concrete shapes made with these aggregates had bulk densities ranging from S6 to 119 pounds per cubic foot, and all but three of the lightweight concretes had crushing strengths ranging from 3,270 to 6,810 p.s.i. Properties of the lightweight concretes were compared with those of concrete shapes made with commercial aggregates, and with sand and gravel.

Jan 1, 1962

By K L. Silversides, A Chlingaryan, A Melkumyan

Multiple data sources can be fused to improve boundary modelling in stratified deposits such as the banded iron formation (BIF) hosted deposits in the Pilbara Region of Western Australia. Accurate boundaries are essential to produce high quality geological models. Initial models are based on the widely spaced exploration hole data. This creates a high level of uncertainty in areas between the holes, with different interpretations of the boundary equally probable. Including directional information collected in these holes in the models can reduce the number of possibilities. Including data collected during mining, such as blastholes and bench measurements, can further guide the model. This research demonstrates a Gaussian Processes based method of fusing these disparate data sources to better inform the boundaries. Our results demonstrate that when only exploration points are used the model creates a smooth boundary with minimal variation between the holes. Each additional data source refined the model and added additional detail to the boundary. For the blast data, the new detail projects down to the bench below the current bench to allow for a better prediction before mining commences on that bench.

Mar 22, 2022

By R. J. Rotzinger

The Gibraltar Mine and Mill facility were commissioned in 1972 by Gibraltar Mines Ltd utilizing a flowsheet consisting of two stages of crushing followed by a rod mill / ball mill grinding circuit. During operations a number of opportunities were evaluated to expand the mill capacity; however, the economics of the day did not allow any of these projects to proceed. The mine continued to operate until late 1998 when it was shutdown and put on care and maintenance due to low commodity prices. Taseko Mines acquired Gibraltar in 1999 and in 2004, with the improvement in the metal markets, made the decision to restart operations. During the restart planning a number of opportunities for mill improvements and upgrades were identified and, after operations were successfully restarted, the decision was made to once again review expansion opportunities for Gibraltar. Taseko evaluated various expansion alternatives eventually deciding to install a SAG Mill, convert the existing rod mills to ball mills and distribute the SAG discharge to the resultant six 6 parallel ball mills. This paper discusses the design, implementation and commissioning of the SAG mill grinding circuit.

Jan 1, 2012

By Robert F. Chaiken

An absorption-desorption model of particle reactivity was employed to describe the observed relationship between two apparently diverse phenomena which have been the subject of considerable study at the U.S. Bureau of Mines: (1) coal-rock dust reflectance and (2) coal-rock dust explosibility. The model accounts for heterogeneities in particle-size and material properties; however, in the present report, only particle-size distribution is considered. A mean particle-size parameter, appropriate to the explosion extinction process, is derived, and then taken as appropriate to describing optical reflectance. The derived form-to-function relationships for the two processes, when compared with experimental data, suggest that a problem exists with previously derived theory relating optical reflectance to rock dust concentration. A reexamination of that theory leads to a new theoretical expression, changed by a factor of 2, for the variation of rock dust concentration with reflectance which is in quite good agreement with experimental results. The current work offers justification for measuring and establishing rock dust requirements for specific coal dust size distribution(s) found in the mine-distributions that undoubtedly depend on the mining method and the type of coalbed.

Jan 1, 2010

By Yuanbo Zhang, Zijian Su, Bingbing Liu, Guanghui Li, Tao Jiang

With the depletion of rich manganese ores, high-Fe content manganese ores are becoming the mainstream resources for manganese extraction. Reduction roasting-magnetic separation process is reported as a relatively effective route to realize the separation of manganese and iron. This study investigated the phase transformation of MnO2 and Fe2O3 briquettes (molar ratio 1:1) roasted under various temperatures and CO–CO2 atmospheres. Results showed that when the CO content was in the range of 0–10 vol%, MnxFe3−xO4 (x = 0−1) phase was formed and its content increased with the rising of temperature. The formation of ferromagnetic MnxFe3−xO4 with strong magnetism resulted in an inferior separation of manganese and iron by magnetization roasting-magnetic separation process. With the increase of CO content to over 25 vol%, the MnxFe3−xO4 content decreased while the content of feebly magnetic substance (MnO)y(FeO)1−y(y = 0−1) increased. Further increasing the CO content to over 80 vol%, (MnO)y(FeO)1−y was reduced to MnO and metallic iron.

Mar 1, 2017

By Peter Moser, Mark Ganster, Radoslava Ivanova, Florian Bauer

Blasting accurately in underground drifts and creating a smooth contour requires proper drilling, knowledge about the apparent geology, a well designed blast pattern and ideally a smooth blasting product. These products are usually cartridged explosives with less energy and are charged in the contour holes in order to reduce the energy concentration and therefore the cracking into the surrounding rock. With the development of a new contour blasting system, a device can now be delivered to the industry that that avoids the additional storage of cartridged products when bulk explosives are used. The system consists of a foldable hose that is charged with bulk emulsion, in the same way as the rest of the blast, from the base to the collar of the hole. It centers automatically in the borehole and provides a decoupled charge. The paper describes the system in detail, gives background information on smooth blasting and presents the first successful field tests using the system in the drifts of an underground mine. It shows the advantages of blast results that produce more stable contours that reduce the amount, time and cost for support but also increase safety underground.

Jan 1, 2012

By Frank E. Chase

Preventing pillar squeezes, massive pillar collapses, and bumps is critical to the safe and efficient recovery of coal during room-and-pillar retreat mining. To help prevent these problems, the U.S. Bureau of Mines (USBM) has developed the Analysis of Retreat Mining Pillar Stability (ARMPS) computer program. ARMPS calculates stability factors (SF) based on estimates of the loads applied to and the load-bearing capacities of, pillars during retreat mining operations. The program can model the significant features of most retreat mining layouts, including angled crosscuts, varied spacings between entries, barrier pillars between the active section and old (side) gobs, and slab cuts in the barriers on retreat. It also features a pillar strength formula that considers the greater strength of rectangular pillars. The program may be used to evaluate bleeder designs as well as active workings. A data base of 110 pillar retreat mining case histories has been collected across the United States to verify the program. It was found that satisfactory conditions were very rare when the ARMPS SF was less than 0.75. Conversely, very few unsatisfactory designs were found where the ARMPS SF was greater than 1. 5.

Jan 1, 1995

By Adam J. Gesing

The eddy current separator (ECS) is designed to separate nonmagnetic (nonferrous) electrically conducting (metallic) particles from nonconductive residue. Nonferrous metallic particles are repelled out of the material stream passing over the eddy current rotor (ECR). The rotor is housed in a fiberglass composite outer shell that serves as a conveyor head pulley. This results in the desired metaVnonmeta1 separation. The behavior of ferromagnetic particles, mainly iron and iron oxide (i.e. rust), is quite different. These particles are strongly attracted to the magnets and the smaller particles tend to align their long axis in the direction of the magnetic flux. Since the direction of the flux changes with the passage of each magnet pole, the small particles spin at very high rates causing wear of the belt and of the composite outer shell housing the ECR. Large particles, when trapped under the ECS belt, cannot spin, but can be heated by the eddy current effects and subsequently can burn through the composite outer shell. We discuss the practical implication of this behavior of iron and rust on the design, performance and maintenance of eddy current separators.

Jan 1, 1999

By M. A. Elliott, F. W. Brown

"INTRODUCTION During the recent war the Bureau of Mines, at the request of one of the armed services, investigated the hazards that night be encountered 5n handling perchloric acid, particularly if spilled on certain materials. The hazardous nature of perchloric acid when mixed with reducing agents had been known qualitatively, but it was desired to obtain quantitative data on the explosion hazards of such materials. Accordingly, tests were made to determine the sensitivity of mixtures of perchloric acid and oxidizable materials to initiation by heat, impact, sparks, flame, and explosive impulses. This report summarizes the results of those tests.PROPERTIES OF PERCELORIC ACIDAnhydrous perchloric acid is a colorless,hygroscopic, volatile, mobile liquid that fumes in the air. The anhydrous acid is unstable at ordinary temperatures, and therefore the commercial acid is a water solution containing either 60 percent or 70 percent by weight of the anhydrous acid. The commercial acid is widely used in chemical analysis, frequently to oxidize organic material. If proper precautions are not observed, such an oxidixation may become exceedingly rapid and result in an explosion. Several such explosions involving the acid are mentioned in the literature. 4, 5, 6/"

Jan 1, 1948

By Long An, Chao Wu, Yuanhui Li, Xing Sun, Shuai Xu, Changyu Jin

Stage open stope mining (SOSM) maintains the stability of excavation openings by leaving a large number of rib pillars. Affected by the strong unloading due to stage mining and the low width-to-height (w/h) ratio of the pillars remaining, largescale destabilization disasters of rib pillars or excavation openings easily occur when the distribution of ground stress or the size of rib pillars is unreasonable. In view of these problems, a physical SOSM model test was carried out based on an underground metal mine in Chifeng City, China, revealing the deformation and failure characteristics of the SOSM pillar group by overloading. The physical model test results of SOSM and room-and-pillar mining (RPM) with a weak pillar were compared, and the failure process of the SOSM pillar group showed the characteristics of rapid and severe damage. The strength difference between a weak pillar and the adjacent pillars enhanced the stress rebalancing effect and extended the failure process of the pillar group. Similar to the SOSM pillar group with a low w/h ratio, some high-strength pillars can be used to avoid large-scale destabilization disasters caused by the synchronous failure of pillars.

Mar 8, 2023

By M. W. Brandt

In the November 1957 issue of "Chemical Process Engineering," a British publications, there appeared an article entitled "Correct Selection of Drying Equipment." The author wrote as follows "Whether batch drying or continuous drying' methods are applied, the basis of efficient drying is heat distribution, control of rate of heat input, and heat transference from heating medium to the particles of the material to be dried." The author continues: "Because the efficiency of direct dryers, such as hot air or hot gas dryers, increases with rising inlet temperature of the drying air or gas when exhaust temperature remains fixed, the highest practical drying temperature should be used. Exhaust air should leave the dryer at the lowest possible temperature, but as fully saturated with moisture as possible." It is certainly conceivable that the author of this article by outlining the basic requirements for efficient drying methods has unwittingly given the reasons why fluidized drying is rapidly being adopted for so many industrail applications, including the dryingof fine coal. An examination in greater detail of the individual basic requirements for efficient drying as outlined by the author is perhaps the most logical starting point.

Jan 1, 1958

By Alfred E. Pugsley

PAYMASTER CONSOLIDATED MINES, LIMITED, began an investigation into the economy and use of detachable bit drill-steel in June, 1937. This investigation has continued to the present time, and was made necessary by transportation and distribution difficulties that had arisen through the use of standard steel in three widely separated mine areas serviced by a central steel-sharpening shop. Detachable bit drill-steel performance was first studied in the workings of No. 2 mine, where the rock being drilled was composed mainly of porphyry or tourmaline, and where standard drill-steel transportation costs had been excessive. The results obtained in this early work definitely established the economy of detachable bit drill-steel at No. 2 mine. This conclusion was reached when the 're-grind' system of re-sharpening dulled detachable bits was 1n use. Preliminary observations on the performance of detachable bit drill-steel in the quartz-carbonate veins of No. S and No. 6 mines gave encouraging results, and warranted a large-scale investigation under practical mining conditions. All drilling operations were gradually changed over to use of detachable bit drill-steel. This change was completed by February, 1938.

Jan 1, 1939