Search Documents

By Mingxia Liu, Qi Liu, Tao Jiang

"In addition to physical parameters such as small mass and high specific surface area of fine and ultrafine minerals, chemical parameters such as the adsorption affinity of collectors on the minerals also plays an important role in fine particle flotation. In this study, we have examined collectors with two different ionized groups, carboxylate and hydroxamate, on the flotation of fine niobium oxide (pyrochlore). To facilitate comparison, two hydrocarbon radicals were tested: octyl and oleoyl, which led to four collectors that were studied: octyl hydroxamic acid (OHA), sodium octanoate (C8OONa), oleoyl hydroxamic acid (C18HA), and sodium oleate (NaOl). Small-scale flotation and isothermal microcalorimetric titration measurements were performed to determine the flotation recoveries of different sized pyrochlore and the enthalpic behavior after adsorption of the collectors on pyrochlore. It was found that the flotation performance of the carboxylate-based collectors was generally inferior to hydroxamate-based collectors. Sodium octanoate could not float pyrochlore irrespective of the particle size of the pyrochlore tested. With a longer hydrocarbon chain, sodium oleate was effective to float the relatively coarse pyrochlore (>20 µm) but its collection efficiency dropped sharply for particles smaller than 20 µm. On the other hand, the two hydroxamate-based collectors, octyl hydroxamic acid and oleoyl hydroxamic acid, showed good collecting ability to both the coarse and fine pyrochlore. The isothermal microcalorimetric titration studies indicated a consistent correlation of chain length with floatability of collectors for relatively coarse pyrochlore, as well as a positive relationship between the adsorption affinity and fine pyrochlore flotation recoveries. The key finding of this study was that efficient fine particle flotation could be achieved when strongly chemisorbing collectors were used.INTRODUCTION The first detailed study of the effect of particle size on flotation was made by Gaudin (1931) with sulphide ores. In 1942, Gaudin again demonstrated that (Gaudin et al., 1942) fine particles possess different flotation properties from larger particles. Since then the effect of particle size on froth flotation has been an important research topic by many researchers, e.g., Gaudin (1957), Miettinen et al. (2010), Warren (1976) Jameson (2010), summarizing the behavior of fine particles in terms of their low particle momentum, leading to low rate of collision with bubbles which reduces the chance of adhesion. The suggested remediation methods are mainly based on two approaches: increasing particle size or decreasing bubble size (Warren, 1976). Sand-fine splitting followed by separate flotation treatment of the sand and fines, using deep flotation cells, using starvation quantities of collectors, and using long flotation times, are also strategies to address the problems of fine particle flotation."

Jan 1, 2018

By Felicia F. Peng

Employing the combination of two types of polyelectrolyte might become necessary to enhance both settling rate of the flocs and water clarity of fine particle suspension in high capacity thickening process. The sequence of addition, mixing, type and dosage of polymer affect the overall performance and capacity of a thickening process. For the sedimentation of copper flotation tailings, the cylinder test results showed that two different techniques may be used to achieve the required performance including high settling rate of flocs, underflow density and overflow water clarity, by either adjusting pH prior to anionic polyelectrolyte flocculation, or using a combination of polymer flocculant and coagulant (dual polymer system). The dynamic thickening testing results showed that only the approach using a dual polymer system is able to meet the required performance. The effects of polyelectrolyte dosage, the sequence and numbers of polyelectrolyte addition, feed concentration, bed level and rake speed on the settling rate, underflow solid, and water clarity were studied in cylinder test and a laboratory dynamic thickening unit with various conditions related to the thickening process. The dynamic test is especially valuable in evaluating the addition and mixing of polymers. The results were evaluated quantitatively, using total suspended solids in supernatant, underflow density and capacity per unit settling area per unit time as the measure of effectiveness. The objective of this study is to quantify and explain some of the parameters involved in the sedimentation of copper flotation tailings.

Jan 1, 1997

By Christopher Mark

The Analysis of Retreat Mining Pillar Stability (ARMPS) program has been used to evaluate room and pillar retreat mining layouts since it was first released in the mid 1990s. After the Crandall Canyon mine disaster focused attention on the importance of pillar design, ARMPS became an essential component in most Roof Control Plans developed by mine operators. In 2010, NIOSH released ARMPS version 6, which features a ?pressure arch? loading model for deep cover room and pillar mining. NIOSH has also provided general guidance for using ARMPS, including design criteria based on statistical analyses of an extensive case history data base. Many real-world retreat mining scenarios entail mining configurations that ARMPS does not directly address. Some of these situations that the MSHA Roof Control Division (RCD) has encountered in the course of its reviews of more than 100 ?complex and non-typical? plans are ? Unmined pillars are left at the mouth of a retreat panel that function as a ?composite barrier pillar? ? The floor is extracted on retreat, increasing the mining height ? More than one row of bleeder pillars is left in an adjacent, previously mined panel ? A retreat panel is located above or below a gob area in a previously mined seam ? Bleeder pillars are partially extracted on retreat RCD has developed solutions that allow these situations to be fitted into the ARMPS framework, and these are presented in this paper. Also discussed are some of the rules of thumb that have been developed for various input parameters, such as the treatment of inseam rock and slab cuts into solid coal.

Jan 1, 2011

For handling rough rock, the shovel-train system is unexcelled. The ideal application is a physically large, but not excessively deep, open-pit mine from which the coarsely blasted ore and waste must be transported distances in excess of three miles. If, in addition, a high production rate is to be maintained, railroad haulage will probably afford a lower cost per ton transportation than will any other haulage method. Relatively gentle grades must be employed- usually 3% for uphill hauls and 4% for downhill hauls. The greater the differences in elevation the greater are the railroad track grade space requirements. By way of illustration, a 3% ramp out of a pit only 300 ft deep must be almost two miles long. Mainline track locations should be selected carefully so that the frequency of movements during the life of the mining operation is minimized. This applies both to ore and to waste haulageways. Such moves are not only expensive but difficult to execute without adversely affecting production rates. The large mine affords greater opportunities for judicious location of semi-permanent trackage.

Jan 10, 1967

By W. H. Tomlinson

Although the thoughts and efforts of the great majority of people in many parts of the world are today directed toward killing each other, the purpose of this paper is to discuss means of conserving human life. In a world of turmoil and strife, we find time to discuss and make plans to achieve our objective -prevention of the "sacrifice" of life through avoidable accidents. The word" sacrifice" is used here advisedly, as one meaning of the word given in the 1942 edition of Funk and Wagnalls New Dictionary of the English Language is "the act of giving up some desired or valued object for the sake of *** future good." As everyone agrees that life is man's most priceless possession, one wonders if past sacrifices have been in vain. It appears that life is cheap in America; it is cheap because some of the industrialists are too much concerned with making a profit to devote much time and thought to conserving human life; it is cheap because some labor leaders apparently are interested solely in personal power and prestige; it is cheap because a great many workmen fail or refuse to cooperate energetically with the various organizations interested ill; their safety and welfare; it is of little value because, individually and collectively, we are indifferent to our responsibilities toward our fellow men.

Jan 1, 1944

By Frances H. Clark

IN wartime, the fabrication and use of metals assumes increased importance, for a modern war of sizable proportions cannot be undertaken with- out a vast supply of this material. Light alloys of aluminum and magnesium, which were comparatively unknown in the last war, will play an important role in this one. Due to research on a vast scale in the interim of years, industry is today well equipped to fabricate metals on an enormous scale. Research for the past year has been most productive and a comprehensive survey in the space of this article would be impossible. It is hoped that the stressing of a few items here and there out of a great quantity of able work will indicate in a small way the advances made within recent times. Specific references to the literature will be omitted at the Editor's re- quest but some authors of papers that I have found of special interest are mentioned.

Jan 1, 1940

By Robert H. Peters

This Bureau of Mines report describes several significant problems associated with absenteeism among underground coal miners. The vast empirical literature on employee absenteeism is reviewed, and a conceptual model of the factors that cause absenteeism among miners is presented. Portions of this model were empirically tested by performing correlational and multiple regression analyses on data collected from a group of 64 underground coal miners. The results of these tests are presented and discussed.

Jan 1, 1987

By Karl J. C. Harries

"1.1. WHAT ARE AGREEMENTS AND HOW ARE THEY FORMED?In order to have an agreement, at common law, there must be an offer, acceptance of that offer, and consideration passing between the parties. In addition, the material terms (i.e. the basics or substance) of the agreement must be discernible, preferably by means of documentation. Although these concepts may appear simple and straightforward, the law relating to them is voluminous and complex. Some brief comments are worthwhile.• Offer/acceptance: Both offer and acceptance should be in writing, but they need not be. The actions, conversations, and/or correspondence of the parties may constitute either or both of them. Notwithstanding, the local law or practice of a jurisdiction will impose some specific requirements for certain types of agreements. If these requirements are not met, the agreement may be unenforceable. For example, Ontario’s Mining Act requires transfers of unpatented mining claims to be evidenced in writing and recorded.1• Consideration: Consideration is usually thought of as being money, but it can be virtually anything, even “the premises” (i.e. the mutual covenants or promises contained in the agreement itself). In addition, if one party, relying upon the offer of another, does something to his detriment, then the doing of the act can be considered to be an acceptance of the offer and, under the legal concept of “detrimental reliance”, can also be consideration. Whether or not detrimental reliance exists will depend upon the circumstances of each case.2• Material terms: The requirement that the material terms of an agreement must be discernible does not mean that all of the terms of an agreement must be documented or even have been considered, just the basic or material ones. In addition, it will be up to a judge to decide what is material – not necessarily the parties. In order to establish the material terms, a Court may look at all relevant documentation and may hear oral evidence. It will resist “writing the agreement”"

Jan 1, 2003

The Bureau of Mines has studied 260 underground coal mine fires which occurred from 1970 through 1989. Every fire had the capacity to be hazardous to life and property, however upon closer examination some were found to be inherently more dangerous than others. Our research involved reviewing and recording specific information contained in published Mine Safety and Health Administration fire accident reports. The objective was to determine if degrees of hazard relative to fire source or location could be construed from information contained in the reports. We specifically looked at the propensity for fires to cause injuries and fatalities as well as the need to seal the area in order to extinguish the fire. Relative to all underground locations, this review found that fires occurring in main haulage-ways were most likely to cause injuries and fatalities as well as require sealing of at least the immediate area to extinguish.

Jan 1, 1993

By Zhiqiang Wang

This paper mainly focuses on the method of ?three-zone? definition (a caving zone, a fissure zone and a curve subsidence zone) for full height cutting in a thick seam. Based on criteria of a caving zone and a water conducting zone, as well as existing research achievements, it is believed that there exists great error for calculation of height of the ?three-zone? area using cutting height and the coefficient of bulk increase. Dynamic factors should be considered, so, based on the theory of key rock strata and combining this with several other factors, such as mining area, this paper presents a new method to determine the overburden ?three-zone? definition. The results are as follows: (1) geometric models of a working face and key stratum are established through the rock displacement angle, with consideration of the influence of mining on the key stratum (the range of key stratum influenced by mining is enlarged as the mining area increases); (2) because there is always a cavity below the key stratum of the thick coal seam with full seam cutting, and the key stratum gradually fracture with face advancing, based on the geometric dimension of strata, the maximum fracturing interval expression has been presented, including the working face advancing range. This can theoretically lead to the location of the key stratum influenced by mining, and its stability before mining, helps to confirm which zone the key stratum and following-up strata belong to, using the criteria of sliding instability or deformation instability; (3) the new method of ?three-zone? definition which is based on the theory of key rock strata is first proposed for full height cutting in thick seam. Finally, combined with practical engineering, and comparing with field data, it is believed that the proposed method is more objective than existing methods.

Aug 1, 2013

By I. Ward, E. Milosavljevic, M. Botz

"The silver nitrate titration method is a rapid and acceptably accurate means of analyzing for cyanide in leach solutions that contain primarily free cyanide. However, in leach solutions containing elevated levels of copper, the titrimetric method overestimates the concentration of free cyanide and underestimates the concentration of weak and dissociable (WAD) cyanide. The authors have developed a modified potentiometric (MP) titration method for determining WAD cyanide that overcomes issues associated with high copper levels in solution. The new MP-WAD method involves addition of a chemical ligand to the sample prior to silver nitrate titration to release cyanide bound to copper. Once released from copper, cyanide in solution is no longer affected by the presence of copper, and titration results are quantitative rather than empirical. In multiple laboratory trials with synthetic solutions and complex actual leach solutions, analytical results obtained with the new MP-WAD method were found to be within about ±5% of analyses obtained with the USEPA OIA-1677 WAD cyanide analytical method.IntroductionThe silver nitrate titration method is widely used to estimate the concentration of cyanide in leach solution for purposes of cyanidation process control. Cyanide determined by silver nitrate titration is commonly referred to as “free” cyanide, but frequently should be referred to as “titratable” cyanide. By definition, free cyanide is the sum of the concentrations of aqueous hydrogen cyanide HCN(aq) and the cyanide anion CN- (ASTM, 2010). Titration will only yield a reasonably accurate measurement of free cyanide when metal-cyanide complex concentrations (e.g., cadmium, copper, mercury, nickel, silver and zinc) in solution are low. In other words, titration will only yield a reasonably accurate measurement of free cyanide if the solution primarily contains free cyanide."

Jan 1, 2015

By R. Farrar

Protective canopies for conventional electric face equipment, including shuttle cars, operating in low coal (less than 48 inches) were designed, fabricated, installed and evaluated on in-mine machines engaged in regular coal mining operations. This work was performed under contract to the U.S. Bureau of Mines, Pittsburgh Mining and Safety Research Center. The canopies will support a vertical load of 18,000 pounds and provide protection against both roof falls and contact with the mine rib. Canopy configurations were established based on human engineering studies, full scale canopy mockups, and in-mine observation and consultation with mine and equipment manufacturing personnel. Overall height of each canopy is hydraulically adjustable between a minimum of 32 inches and a maximum of 40 inches. Canopy tops are open framework, welded structures, covered with expanded metal mesh. Structural members are 1 3/4-inch or 2-inch square tubing of AISI 413ON and ASTM A500 material, respectively. The canopy tops are typically supported by an understructure and upright post arrangement that is either integrated into the current operator platform or attached to the machine frame. The four upright corner posts house the hydraulic actuators. Canopy tops are elevated horizontally. Canopies are welded or bolted to the existing machines. Installation is accomplished with a minimal amount of interface modifications. No major machine design changes are required. Canopies were trial installed and load tested at the manufacturer's facility prior to installation on the in-mine machines. Canopies were installed on a Joy 14BU10 Loader, 16RB-3AH Cutter, and two 21SC Shuttle Cars, and a Galis 300 Roof Drill and 460-S Face Drill. Canopy installations were evaluated in the Jewell Ridge Coal Company No. 12 and Big Creek Tiller Mines. Operational time accumulated on the installations during evaluation ranged from 1 week to 14 weeks of two-shift operation. All five canopy designs, manufacture, and test were successfully accomplished. The five canopies met all safety requirements. Three of the five canopies were deemed to be completely successful from an operator's point of view. That is, mine management as well as the machine operator found that the canopies did not impede the operation of the machines to function with the same efficiency as before the installation of the canopies. The loader canopy, in fact, appeared to have provided a mole efficient operation of the loader by providing added safety to the operator from rib contact thus allowing him to concentrate more fully on the loading function. Operational problems were encountered with the shuttle car and the roof drill. The shuttle car canopy obstructed visibility to an objectionable amount and the roof drill canopy impeded maneuverability of the machine, more than doubling the roof bolting time.

Jan 1, 2012

By Scott Turner

Since my whole life has been spent in the mining business , I naturally tend to address my remarks particularly to the newly- graduated mining and metallurgical engineers among you . To a certain extent , all forms of engineering principles are involved in the training of the mining engineer , and most sorts of engineering are certainly utilized by him , so that every one of this graduating class is concerned with the field I propose to discuss . The fact that , beginning with to - day , you will always be styled engineers , indicates that you have passed successfully through preparatory school , and have survived the hard grind of the technical college . One object of your training here has been to instruct you in accurate , close , and clear thinking . Your minds have been taught to act directly , calmly . and always to the point . By now , you should know how to get facts , look far , and think through . You are supposed to be willing to recognize and adopt sound engineering principles and practices , in so far as they are known to you , and to furnish character , ability , and devotion to your calling . Some of you may have had a general college course before coming here to specialize in engineering . Where that has been possible , I hope it is the case , since a liberal educational course tends to make the alumnus more flexible and adaptable than the purely scientific graduate. The broader education enables one to change , with less serious loss , from one job to another; ready adaptability is a great asset ; the engineer should be capable of much more than a single special task . The necessary preliminary training for a professional occupation is intellectual in character , involving knowledge , and to some extent learning , as distinguished from mere skill . The well -balanced engineer is expected to embody a happy combination of theory and fact , of pure science and material reality ; experience shows that he is apt to give a good account of himself , once he gets the chance . For the long pull , the importance of unquestioned integrity can not be overemphasized . Leaders of big business sometimes have need for a man as agile and unscrupulous as a cat on a back fence ; on occasion , they may have to employ brilliant , smart , spectacular , and crafty people , but when the special purposes for which such men are hired have been accomplished , they are no longer wanted . Given natural health , intelligence , ability , and adequate training , probably the characteristics most admired in the young employee are steadiness , dependability , and loyalty . The last is the best . If you can not be simple , direct , and faithful in your dealings with your administrative superiors , no one will want you for long . I believe these points are of primary importance to the young engineer . Your groundwork must be right before you can get far . These personal characteristics are what eventually determine your relations with men and affairs . They are vital in the human engineering which may be a large part of your work .

Aug 1, 1932

By P Bartlett, K Naidoo

Premier Diamond Mine is planning a new, mechanised, block cave, with a production level approximately 1000 m below surface. A high degree of tunnel damage is expected, due to stress and the relatively low in situ strength of kimberlite. An evaluation of the timing of tunnel excavation, tunnel size and spacing has been carried out to define critical parameters for planning layouts and development schedules. Extensive use has been made of three-dimensional FLAC3D numerical models, calibrated against known rock mass behaviour at 650 m depth, to examine the influence of undercut advance on production level excavations. These were able to represent the effect of stress rotation on tunnels during undercut advance and the effect of an inclined undercut. The analysis has provided guidelines that are possibly applicable to any deep block cave layout. The choice of drawpoint layout is of considerably less significance than the proportion of ground extracted on the production level elevation prior to advancing the undercut. The analysis shows that damage to production development will be potentially severe if it is all excavated prior to advancing the undercut, or is mined directly beneath the undercut face. The development of the main production tunnels alone ahead of the undercut may be feasible, but no breakaways should be put in as they appear to trigger a rapid increase in the severity of damage. The optimal sequence is when all production tunnels are developed at least 10 m in plan behind the undercut, where the induced peak field stress is less than 20 MPa and a maximum support pressure of 100 to 500 kN/m2 is require to contain movement. The assessment showed that the conditions are not significantly improved by increasing drawpoint spacing from 15 m to 18 m. The vertical spacing between the undercut and production level beneath is investigated. Provided production level development is carried out beneath the undercut, there would appear to be little benefit in increasing the vertical spacing between the undercut and production level beyond the current 15 m to 18 m.

Jan 1, 2000

This Bureau of Mines report is a reference manual of procedures used by the Bureau's Twin Cities Mining Research Center for obtaining rock properties. Included in the report are discussions on the usage of each property, descriptions of the general test methods for obtaining the properties, and instructions for performing the tests. The Instructions embrace details of the specimen configuration, test apparatus, test procedure, test conditions, and calculations needed to achieve satisfactory results. Although the procedures presented in this reference manual generally conform to recommendations of the ASTM Administrative Committee on Standards, they are not purported to be standards.

Jan 1, 1974

By R. G. Warncke

In the 1953 National First-Aid and Mine Rescue Contest, 58 teams from 9 States participated, 14 teams from 6 States in mine rescue and 47 teams from 9 States in first aid. Three of the teams were combination teams in that the same team participated in both the mine rescue and first-aid contests. The States represented and the number of teams from each State are shown in table 1. [ ] The contest was conducted in accordance with the general rules prepared by the Rules Committee and approved by the General Committee of the National First-Aid and Mine Rescue Committee.

Jan 1, 1955

By A. G. Loomis

Although secondary-recovery methods have not been applied widely in California, it is apparent that increasing attention and effort must be given to this phase of recovery if the State is to maintain its high rank as a petroleum producer. Steadily increasing demands for petroleum products and decreasing rates of discovery of new oil fields, with rapid depletion of existing reserves, emphasize the prospect of an adverse situation of supply and demand in the not-far-distant future. If the trend of discoveries becomes more favorable or if more complete economic recovery of the oil in place can be obtained by secondary recovery, this situation can be averted. Not only are these reserves of economic importance to the petroleum industry for meeting increasing market demands; but economic reclamation of such reserves is an important conservation measure, which will prolong the productive life of many fields. Accordingly, progressive operators in California are alert to the possibilities of secondary recovery and have done much to implement such operations wherever feasible. Most current operations are of the pressure-maintenance type, in which the reservoir pressure is maintained or partly maintained by injecting natural gas to in-crease oil recovery. The possibilities of recovering additional oil from stripper fields by gas drive and water flooding (including water disposal) also are being tested in experimental field projects. Table 1 summarizes current gas-and water-injection projects in California.

Jan 1, 1952

By Serge Rudchenko

A study to determine the potential use of retaining structures in open pit backfilling. Research and review of the open pit mine environment, mine waste disposal, and past and current use of retaining structures. A development of specific structures, the culvert/ tunnel concept, and an anchor block retaining concept. The cost benefit of retaining structures used for in-pit backfilled waste.

Jan 1, 1981

By William R. Hardwick

Present information indicates that a copper deposit can be safely fractured with a nuclear explosive and the copper successfully recovered by the in-situ leaching method. The process is not yet at the stage where it can be presented t ) the mining industry as a technique proven in all its aspects, but it is a method with high success potential. Unknown factors must be evaluated by a full-scale test before the economics or the extent of the use of the method by the mining industry can be predicted. Preliminary calculations indicate that the cost of fracturing a copper deposit nuclear explosives may range from l.8 to 55.2 cents per ton or in some case: less than a cent per pound of recoverable copper. Copper may be recovered at less cost than by conventional methods. Deposits with 4 pounds of recoverable copper may be economic and production from a deposit may begin in less than half the time required for conventional methods.

Jan 1, 1967

By J. F. McCoy

The quantitative determination of the mass rate of flow of methane in an underground airway is calculated as the product of the methane concentration and the air flow rate. Velocities are taken at several points and then averaged over the airway cross section to determine the total volume flow. Errors in velocity measurement thereby result in errors in total volume flow as well as the mass flow rate of methane. The purpose of this program was to evaluate existing instrumentation for measuring air velocities in the speed range under 2000 feet per minute; to evaluate the method for determining total air volume flow from the velocity measurements; to evaluate new techniques which may be applied to measuring air velocities; and to design a prototype instrument which represents the best technique based on the evaluation. The instrument should be: a. portable b. self-contained c. insensitive to dust, moisture and temperature changes d. safe for use in gassy mines

Jan 1, 1972