Search Documents

By Donald F. MacDonald

This report aims to discuss, from the viewpoint of the mining geologist, the bearing of topographic and geologic conditions on cer- tain problems that arose in the construction of the Panama Canal. T+ is published by the Bureau of Mines as a contribution to engineer- ing liters ure because it presents information that shows how geology and topography must be considered by the mining engineer in plan- ning excavations and in removing loose material and solid rock in the safest and most efficient manner. The printing of this bulletin has been approved by the governor of the Panama Canal, as it was impracticable for the Panama Canal to give this information to the general public in any of its publications. The "sword cut" of Goethals and his men did not sever the Isth- mian barrier; it merely clove the hills to a depth of 40 feet above sea level. This cut and the great areas of low valleys at both ends of it have been covered with fresh water to the 85-foot level. This high-level lake held by dams at either end, the 85-foot locks, by which ships enter it, and the dredged approaches from the two oceans constitute the Panama Canal. In the preparation of accurate estimates concerning the cost of large excavations information regarding the geologic conditions, as obtained by a study of natural features, is necessary. Drill holes and test pits will furnish supplementary geologic information, but without a gen- eral knowledge of the geologic conditions it will not be possible for the constructing engineer to answer such questions as the following: (1) What rock units will be encountered in the excavation and in what proportion? (2) What will be the cost of drilling each for blasting (3) How far apart and how deep must the drill holes be to efficiently break the rock of each to the proper size-not too fine nor yet too coarse? In this connection jointing, fissuring, bedding, toughness, and other physical characteristics must be considered (4) How steep will the slopes of the excavation stand, and to what extent will they wash and trench on exposure to the atmosphere? (5) What proportion of the material to be excavated is of such physical character that it may be utilized in any other part of the project, such as in concrete construction, road making, wharves, breakwaters, riprap work, etc.

Jan 1, 1915

By IRVINGC. ALLEN, W. A. Jacobs

Realizing the great importance and wide application of petroleum and its products for fuel,lighting and lubrication, and the absence of authentic and comprehensive information in the literature on the commercial value of American petroleums, the United States Geological Survey has for a number of years' been making analyses and other examinations of these oils and their products. In 1907 the technologic branch of the Survey began a study of certain economic problems having to do with the natural mineral oils. The prime object of the investigations was to determine the economic value of the petroleums and natural gases in the United States with special reference to the supplies in the public lands, and to ascertain how these resources could be utilized in the industries withleast waste and greatest efficiency. This work, which is now being conducted by the petroleum section of the Bureau of Mines under authority of the act of May 16, 1910, will include the collection at the wells and refineries of information as to the following details: Facilities for handling and storage at the wells. Facilities for transportation, whether by pipe line, rail, or water. Distance to the nearest port or center of industry and time necessary for delivery. Facilities for storage at such point of delivery. Suitability of the crude oil for fuel, or the treatment necessary to convert itmost economically into the best fuel. Best processes of refining or of converting the crude oil into its many products. The examination of these products. The utilization of the by-products and residues of the refineries. The collection of adequate and reliable samples, and the complete chemical and physical examination ofthese samples in the laboratory.

Jan 1, 1911

By Cong Wang, Kexin Jiao, Yongan Zhao, Haibin Zuo, Jianliang Zhang

The carbon composite brick is a new refractory used in blast furnace hearth and bottom. It caused wide attention due to its high thermal conductivity and low erosion by molten iron. In this paper, chemical constituents, SEM-EDS and X-ray diffraction were carried out in order to understand reaction mechanisms. A series of experiments of oxidation resistance characteristics were made. The oxidation mechanisms of carbon composite bricks in the presence of air were analyzed. According to the analysis on many experimental results, the oxidation process of carbon composite bricks under different temperatures were controlled by different mechanisms. In the condition of high temperature, SiO2 as oxidation product hindered the diffusion of O2, and reduced the oxidation loss of graphite in the internal.

Jan 1, 2015

By F Debidin

The progressive rise of an H-pile during driving of an adjacent pile is described in this case history in which piles 15 to 18 m long were driven to end-bearing for the foundations for a 230 m long building. The use of a reaction beam-soil anchor system for compression load tests is discussed. The results of static load tests to determine pile capacity are compared with those obtained by the Pile Driving Analyzer and by theory. Unusual high temporary compressions were observed by field control staff. Proof testing was necessary to determine the need for restriking of some piles in which rise had occurred.

Jan 1, 2010

By Fred C. Turin, Lisa J. Steiner, Kim M. Cornelius

Like many experienced workers, remote control continuous miner operators perform their everyday jobs making choices and decisions that they may not consciously think about. While performing tasks, they are continuously processing feedback and cues which guide them for the next move. Initial training teaches the operators the tasks necessary to operate the equipment and perform the job. However, with experience they are better able to deal with hazardous conditions and non routine situations. To better understand what potential cues and feedback help to guide the operators, a questionnaire was developed to learn what factors affect decisions. Operator responses address issues related to specific tasks, equipment operation, visibility, lighting, and communication issues. The information collected is useful to understand what cues experienced operators use to make task performance decisions. Results will be used to develop interventions and training for safe and effective operator performance.

By Fuqiang Zheng, Yufeng Guo, Guanzhou Qiu, Tao Jiang, Xiaoming Qu

MxTi3-xO5 is the main titanium-bearing mineral in the titanium-bearing electric furnace slag (TEFS), which is produced by direct reduction-electric furnace smelting process with vanadium titanomagnetite concentrate in Panzhihua-Xichang region of China. In order to effectively utilize the titanium resource in TEFS, the thermomechanical analysis and conditions for the growing up of MxTi3-xO5 grain were investigated, which emphasized on the effects of CaF2 and cooling rate on the crystallization of MxTi3-xO5 in the melting process. The mineral phase and morphology of titanium-bearing slag were determined by XRD and electron microscope technique, respectively. The results indicated that the average grain size of MxTi3-xO5 grown up from 30 to 92 lm and the area fraction of MxTi3-xO5 reached about 66% from 61% under the conditions of 5 wt% CaF2 and cooling rate at 1 °C/min.

Mar 1, 2017

By K. Ogawa, T. Yokoyama

Hydraulic fracturing technique, an applied technique to cause tensile fractures to rock by injecting water pressure to a certain closed section of the borehole, is a measurement method of in-situ rock stress. This technique has the highest track record for techniques used in sub 1000 meter. A feature of this technique is comparatively simple and easy for in-situ stress measurement, because the measurement is applicable when a drilled borehole is available. The predominant advantage of this method is that elastic constants such as Young’s modulus and Poisson’s ratio are not required for determining the value and direction of initial stress. The factors to determine the stress state are the water pressures of re-opening and shut-in of fractures around the borehole wall and its directions. With conventional methods, however, the accuracy of the derived stress states from the observation equations was often adversely affected by the lack of consideration of the remaining water pressure in fractures and insufficient stiffness of the pressurization system. We have developed a new hydraulic fracturing system based on a new test method concept overcoming these defects, and applied to a 300 meter deep borehole in granite. The most important improvement of the new system is an employment of a syringe pump which enables an accurate flow control of fluid with less than 1ml/min in the pressure of 30MPa. Therefore the new test system has a quick response for pressurising in the interval zone, and the measured data was confirmed extremely accurate.

Jan 1, 2015

By G. J. Slavens

The U.S. Bureau of Mines conducted research on preparing submicrometer titanium nitride (TiN) powder as a substitute for tungsten carbide (WC) in cutting tools and wear-resistant parts. Earlier research on a small scale was expanded to include a larger reactor. The TiN powder was produced by contacting titanium tetrachloride (TiCI4) with anhydrous ammonia (NH3) in the presence of Mg at 1,100° C. The powder was collected in an electrostatic precipitator (ESP) filled with ultra-high-purity (UHP) Ar. All collected powder was thermal vacuum distilled to remove Mg and magnesium chloride (MgCl2), leaving the purified TiN. Powder handling and purification procedures were conducted to assure low oxygen content in the powder product. Oxygen content in the distilled TiN powder product was as low as 0.40 wt pct. Nitrogen averaged near 22.0 wt pet with a high of 22.4 wt pct. The purified powder product had an average median particle diameter of 0.14 µm with a standard deviation of 0.09 µm.

Jan 1, 2010

By John Nagy

To facilitate increase in the rate of coal production the Bureau of Mines conducted a study several years ago, on the basis of which the allowable charge limit for permissible explosives in single-hole blasting was raised from 1.5 to 3.0 pounds. Further demands for accelerated production led to consideration of multiple blasting in coal, a practice that is deemed hazardous and is not permitted by most States in this country. In multiple blasting, 10 to 20 pounds of explosive or more may be detonated in a coal face within a fraction of a second, which might result in blown-out or blown-through shots with possible ignition of gas or coal dust. As experimental evidence was lacking, in January 1949 an investigation was undertaken in the Experimental coal mine at Bruceton, Pa., principally to study and compare with single blasting the condi-tions under which simultaneous multiple blasting and particularly multiple short-delay blasting may be practiced without danger of igniting gas or coal dust in mines. The first report on this subject was presented at the last international conference of mine safety research. Since that time numerous additional experiments have been made; because of other pressing problems the work has been brought temporarily at least to a conclusion. This paper is the second report on the problem. It does not contain a detailed description of all test conditions and test arrangements, many of which were described 2 years ago in part 1 (now available as Report of Investigations 4868), but the conclusions are based on the entire study. A more complete review, which will incorporate data from the entire investigation, is being prepared as a Bureau of Mines bulletin. Up to the present time, short-delay blasting of coal in commercial mines has been introduced only experimentally in Washington and in a few mines elsewhere. If the system is adopted more generally, new problems may arise, and the study may have to be reopened.

Jan 1, 1952

By B. A. Hillman

Silicon is the second most abundant element on earth, exceeded only by oxygen. Silicon dioxide forms a crystalline structure of repeating SiO2 molecules which form characteristically hard, durable crystals. As a result, crystalline silica is Ubiquitous in the crustal rocks, sediments and the mineral products derived from mining. An examination of the history of studies that identify silica as a human and animal carcinogen is presented in the context of the development of a public health policy in California. The implications for the cost of conducting aggregate and other mining operations in the state are discussed.

Jan 1, 1992

By Wilbert J. Huff

The organization of the Explosives Division is indicated by the accompanying chart (fig. 1). As this has been discussed in a previous report3/, it will not be considered further in this report. The activities of the various units are outlined below. I. INFLAMMABILITY OF GASES AND VAPORS4/ Determination of the Explosion Hazards of Combustible Gases and Vapors Found in Mines and Industries The Explosives Division maintains, at the Pittsburgh Experiment Station, a laboratory specially equipped for the determination of the explosion hazards of combustible gases and vapors. Of particular importance, is the determination of the chemical composition within which explosions may occur and beyond which there is no danger of explosion, combustion or inflammation. These limits, known as the limits of inflammability, as determined by this and other laboratories, have been compiled in Bulletin 279 of this Bureau. The last revised edition (1931) of this bulletin has been exhausted. Since it was published, the Pittsburgh laboratory has determined the limits of about 40 combustibles and has ascertained more precisely ant accurately many previously published limits.

Jan 1, 1938

By Robert H. Richards

(Pittsburg Meeting, March, 1910.) THIS is in part a review paper, indicating the various steps that have been taken in developing hindered-settling apparatus, some of the standard data that have been obtained, and some of the conclusions one is led to as to the effect of it in improving concentrating-methods and machinery, and in part it brings in some unpublished work. CAUSES OF LOSS IN ORE-CONCENTRATION. In making a study of the separation of valuable minerals from the waste gangue, particularly by water concentrators, it is necessary to define, first of all, what are the causes of-loss that are likely to interfere with the concentration. Having made this definition; we can then study to see in what way the machines make their losses, and plan remedies for them in an intelligent way. Losses may be stated to occur as included grains, as flat or long grains, as fine free mineral, and as absolute slime. We will take, these up one by one, as follows: Included Grains.-Fig. 1 shows by a set of diagrams how included grains may occur: first, where the heavy mineral grains attached to the quartz are of large size; secondly, where they are of small size ; and thirdly, where very fine particles of heavy mineral are included in the quartz. We have to decide in regard to included grains whether they are rich enough to go direct to, the furnace, or poor enough to throw away, or whether they lie between these two points and require recrushing as the only means of severing the values from the waste. This last case is the only one requiring special treatment at our hands. We will therefore consider that next. * By mutual consent, this paper has been presented also before the Colorado Scientific Society, and the Canadian Mining Institute, Montreal.

Feb 1, 1911

By Oliver C. Fursman, Lloyd H. Banning

This research was undertaken to determine the feasibility of producing steel from hydrogen - reduced , pyrophoric iron powder . Before steelmaking tests were begun , investigations were made to develop procedures for handling the pyrophoric powder safely , and melting tests were made in a single - phase , electric - arc furnace to determine inert gas requirements for preventing powder oxidation . Steelmaking tests were conducted in a conventional electric - arc furnace , usually by a two - slag basic procedure . Results of the research indicated that ( 1 ) pyrophoric powder can be handled safely and can be prevented from oxidizing excessively during charging and melting in electric - arc steelmaking furnaces ; ( 2 ) little , if any , more electrical energy is required for melting Cerro Bolivar iron powder per unit of contained iron than is required for melting heavy melting scrap ; ( 3 ) high - quality steel can be produced readily from high- grade iron powder , having recoveries up to 95 percent of the total iron ; ( 4 ) steel can be produced from simulated titaniferous , chromiferous , and manganiferous iron powders ; and ( 5 ) the electrical energy required for melting increases with increase in the proportion of slag - forming constituents in the furnace charge .

Jan 1, 1964

By Amy McBrayer, Andrea Brickey

Area mining is a surface mining method that allows for efficient mining and contemporaneous reclamation of tabular or bedded deposits, e.g., coal. Mine planning methods for area mines differ from those of open pit metal mines. Area mines in the Powder River Basin (PRB) use various processes for mine planning at both the strategic and tactical stages. With the ever changing commodity markets, it is becoming increasingly important for mine operators to be able to react quickly to the changing business environment. Tools that allow for the development and rapid comparison of production schedule scenarios are key to ensuring agile mine operations. A survey of mine engineers responsible for mine design and production scheduling at coal operations provides clarity on the current mine design and production scheduling processes in the PRB, as well as a discussion on potential solutions to upcoming challenges. In this article, we describe various mine planning processes used by the coal producers in the Powder River Basin. The survey identifies a clear gap in the ability to create comprehensive schedules associated with limited tools and lack of engineering labor needed to frequently conduct the mine design and scheduling process.

Jul 8, 2023

By T N. Little

This review paper presents an integrated and practical insight to blasting geology and its importance. This approach involves developing blasting objective up front and implementing geology specific blast designs. The author refers to this approach as ‘starting at both ends’. There are many human-imposed controls on blasting operations, such as: safety, security, legislative, company standards, heritage, and environmental constraints. Thus it is possible for some operators to lose sight of the controls imposed by nature. This paper demonstrates how site geology controls or influences many aspects of the rock breaking processes and how a focus on this aspect has potential to add considerable value to mining operations. It is obvious that mining companies concentrate their efforts on economic/ore geology (good rock geology). However it is the author’s experience that they also concentrate on engineering geology (bad rock geology) only when forced to do so by the ground conditions, but seem to run out of puff before they apply blasting geology (big rock geology). This paper contains five main sections. In the first section, the impact of geological controls on blasthole drilling is briefly discussed in terms of drill selection, penetration rates, bit wear, blasthole stability, blasthole deviation, and health precautions. In the second section the geological controls on aspects of geometric design are reviewed. These include: hazardous minerals, valuable minerals, selection of the blasting techniques, geological structures, blasting direction, and blasting geometry. Section three overlaps with the geometric design section and deals with aspects related to explosives. Topics addressed include selecting the explosive type based on geology, distribution of explosive charge in space and time, explosive performance, and the rock response to explosive loading. In the fourth section, examples are given of the operational complexity needed to implement a blast to cater for difficult bench geologies, environment constraints, past mining (voids) and need for a high degree of quality control. Section five demonstrates geological controls on blast results. Blasting results include the muck pile characteristics, downstream handling and processing, damage to the remaining rock, and blasting emissions.

Nov 8, 2011

By Paul T. Alexander

After evaluating preceding studies and designs of lightweight supports, ESD selected the all-hydraulic and the hydromechanical concepts for detailed design and fabrication. Further analysis and testing showed that the all-hydraulic design was economically justified and met all the crucial engineering, manufacturing, and design criteria identified during the evaluation phase. Following Bureau of Mines approval of the detailed design, four all-hydraulic support models were fabricated. Once functional and structural testing was successfully completed, 40 additional units were constructed and distributed for in-mine testing. The units were very well-liked by all three demonstration mines. The wide- spread interest in supports for seam heights greater than 8 feet led to expansion of the design data package. ESD designed four basic models to cover the new height range, but no hardware has yet been fabricated for the new design.

Jan 1, 1982

By H. P. Greenwald

[In many coal-mining countries, during he pest decade, there have seen made extended studies and accurate measurement of movement of roof strata, tests of the physical properties of specimens cut therefrom, and tests of the strength of end load on artificial supports. Naturally, such studies have been more extensive in European countries, where mining conditions are less favorable than in the United States. As a part of its work in the conservation of coal resource and prevention of accidants in mines, the Bureau of brines began systematic measurements of the movement of roof strata to in coal mines in the fall of 1935. It was decided- that, in the beginning, work on a rapidly retreating rib line in a mechanized mine would give the greatest amount of information in a reasonable time. To this end w cooperative tine agreement was made with the Pittsburgh Coal Co., through Dr. L. E. Young, vice: president in charge of operations, for conduct of work in that company's Montour 10 mine operating in the Pittsburgh coal bed. This paper gives an account of the methods used in the investigation, excerpts from the data obtained, and such generalizations as appear to be justified.]

Jan 1, 1937

By H. P. Greenwald

[In many coal-mining countries, during he pest decade, there have been made extended studies and accurate measurement of movement of roof strata, tests of the physical properties of specimens cut therefrom, and tests of the strength of end load on artificial supports. Naturally, such studies have been more extensive in European countries, where mining conditions are less favorable than in the United States. As a part of its work in the conservation of coal resource and prevention of accidents in mints, the Bureau of Mines began systematic measurement of the movement of roof strata to in coal mines in the fall of 1935. It was decided that, in the beginning, work on a rapidly retreating rib line in a mechanized mine would give the greatest amount of information in a reasonable time. To this end a cooperative agreement was made with the Pittsburgh Coal Co., Dr. L. E. Young, vice president in charge of operations, for conduct of work in that company's Montour 10 mine operating in the Pittsburgh coal bed, This paper gives an account of the methods used in the investigation, excerpts from the date obtained, and such generalizations as appear to be justified.]

Jan 1, 1937

By Robert A. Elgin

The Leadville mining-district (fig. 1) covers approximately 8 square miles adjacent to Leadville, the county seat of Lake County, Colo. It is famous for its large production of rich ores containing zinc, lead, copper, gold, and silver. Some manganiferous ores also have been produced.

Jan 1, 1949

By Staff

This paper contains an outline of the history of the Sullivan mine, now owned and operated by the Consolidated Mining & Smelting Company of Canada, Ltd.; some account of the various methods by which the ore has been treated in efforts to solve the metallurgical problems which its complex character presents, and, finally, to give, as concisely as possible, an outline of the present mining and metallurgical practice along with a description of the mining and milling plant at Kimberley and the smelter and refineries at Trail, in British Columbia. EARLY HISTORY In May, 1892, Pat Sullivan, John Cleaver and Mike Holland left the Coeur d'Alene country, in the State of Idaho, to seek their fortunes in the Kootenay lake district in British Columbia. They were aided in their venture by James Cronin, afterwards locator and owner of the St. Eugene mine at Moyie. Two months later the party broke up, Sullivan and Cleaver crossing the mountains from Crawford bay on Kootenay lake to the head waters of the St. Mary's river, the course of which they followed down to Fort Steele. Here they found a good deal of excitement about the North Star mine, and, joined by "Ed." Smith, who was familiar with this part of the country, they determined to return and prospect in its vicinity.

Jan 1, 1924