Search Documents

The National Institute for Occupational Safety and Health (NIOSH), in partnership with stakeholders in the mining and surface drilling industries, con-ducted research to develop engineering control technologies that reduce workplace noise exposure. The result of this research partnership is the development of a partial cab.

Jan 8, 2007

By J. W. Wilson, P. C. Graham

SUMMARY The Witwatersrand quartzites in which South African gold mining operations are moat exclusively conducted, are notoriously difficult and costly to drill. Despite this situation, however, with the high cost of developing new mines and extending existing mines, together with the rising cost of labour and mining problems resulting from the ever-increasing depths of workings, the demand for raise-boring in these formations is increasing rapidly. Not only is the demand for raises and shafts increasing, but also the length and size of these excavations. Raise-boring studies carried out in South African gold mines have indicated that increased penetration rates and possibly reduced costs could be obtained if higher thrusts were available at the reaming head. Until fairly recently there has been no raise-boring machine suitable for underground use that possessed the thrust and torque characteristics necessary to achieve high penetration rates in hard abrasive quartzite formations and the cutters available were not really developed for high loading. In response to these requirements a raise-borer, the Robbins 83R was designed and built in Seattle, U.S.A. for the Anglo American Corporation. This machine is operating in South African gold mines and is currently being used at a depth of 12 000 ft below surface in one of the. Group's mines. The initial raises bored have substantiated that increased penetration is attainable at high thrust and it is now apparent that the machine is sufficiently versatile to drill raises of up to 12 ft in diameter in quartzite formation over a length of 2 000 ft.

Jan 1, 1974

By D Craw

Uplift of the antiformal ranges in Central Otago, New Zealand , has resulted in the progressive evolution of eluvial placer deposits in tectonic sediments on the range flanks and along their margins. The placers are derived from the reworking of fine-grained gold from the auriferous Manuherikia Group fluvial sediments which covered the basement prior to uplift of the ranges. Gold in the tectonic sediments at Matakanui shows a progressive increase in grainsize in successively younger sediments and nuggets in the youngest gravel sequence are up to two orders of magnitude larger than gold grains in the parent alluvial source. Most of the gold in the tectonic sediments is highly irregular in shape, commonly with delicate surface textures which could not have survived fluvial transport and are indicative of authigenic precipitation. Some coarse grains have been rounded by recycling, and further addition of authigenic gold has occurred. Placer gold values result from both physical and chemical enrichment during sedimentary recycling. Continued range uplift and back-thrusting of sediments on to the ranges results in recycling of earlier formed placer sediments. They also result in further enrichment of gold values through the incorporation of additional supplies of the parent alluvial source sediment The host sediments are widespread along the ranges and are not confined to sites of historic mining activity.

Jan 1, 1992

By K. Saito, Y. Miyauchi, T. Nishi, Y. Kizu

At Tokushima Plant of Nippon Denko Co., Ltd. high-carbon ferromanganese is produced by the electric furnace method using lump manganese ores and sintered manganese ores manufactured from fine manganese ores. However, the distribution of manganese ores is significantly uneven on earth, and their characteristics considerably vary by ore type. It is known from experience that the production of high-carbon ferromanganese by the electric furnace method depends greatly on material ores. Therefore, to maintain stable operation in the electric furnace-smelting field, it is important to identify the characteristics of each type of material ores in advance. Thus, we evaluated the high-temperature electric characteristics of manganese ores using the electrical conductivity measuring system developed by ourselves and provided the standards for determining ores and blending ratio necessary for stable operation of the electric furnace based on the evaluation results. This time we worked for optimisation of the high-temperature electric characteristics of sintered manganese ores through modification of the characteristics because the blending ratio of sintered manganese ores in the electric furnace is high. The electrical conductivity of sintered ores having various chemical components in a high-temperature region (up to 1 550°C) was measured using our electrical conductivity measuring system and high-temperature electric characteristics evaluating method reported at INFACON 9. As the result of the measurement, we revealed that the high-temperature electric characteristics of the sintered ores depend on their chemical contents and the sintered ores can be modified to those having excellent high-temperature electric characteristics by controlling their chemical contents, so that the resources can be effectively used.

Jan 1, 2004

By Grant Goddard

Cameco?s ?Double U? Strategy ? Double existing production ? To 40 million lbs U3O8 annually ? By 2018 ? Existing operations ? Saskatchewan ? United States ? Kazakhstan ? Projects under evaluation ? McArthur River expansion ? Kintyre (Australia) ? Inkai Block 3 (Kazakhstan) ? Development properties ? Cigar Lake project Measures of Success ? Safe, healthy and rewarding workplace ? Supportive communities ? Clean environment ? Outstanding financial performance

Nov 1, 2011

By R. N. Powell

The Pipeline ore body was discovered in March 1991. The construction of the new mine and mill did not start until early March of 1996. Upon completion of permitting and corporate project approval, the 289 million USD project was “fast tracked”. The commissioning began 11 months after start of construction and the project ended 40 million USD under the budget figure. The objective of this paper is to review and highlight the Pipeline Project history from discovery, design, lawsuits, permitting, and re-design through to current - 1998operating practices. Particular emphasis will review the process design, design mistakes, and design successes. The paper will review project history, feasibility, design concepts, operator training, construction, financial and the current operation. Additional discussion will review what design features worked and which did not work within the process plant.

Jan 1, 1999

By Michael D. Justason

This paper details the static and Statnamic load testing on a 600 mm square pre-stressed concrete pile. The pile was located at Pier 15 on the 20 million-dollar Bayou Chico Bridge Project in Pensacola, Florida. The pile was 10.5 meters long and had a design load of 1.3 MN. Three static load test cycles were performed in November, 1996. The Statnamic load test was performed in January, 1997. The Davisson Failure load of the first cycle of the static test was 3.7 MN, and the Davisson Failure load of the Statnamic test was 3.2 MN. The load-displacement curves for the two types of tests were very similar, indicating that the Statnamic load test performed well in the sandy soils. Strain gauges embedded in the pile showed 35% skin friction and 65% end bearing for both test methods. Strain gauges were located at equal spacing at five elevations in the pile. A toe accelerometer verified the rigid body assumption of the Unloading Point Method currently used in the analysis of Statnamic load tests. The data collected from the pile instrumentation was of excellent quality and represents some of the best research to date comparing static and Statnamic load tests.

Jan 1, 1997

By Greg Wyartt

In the Pilbara region of Western Australia, an iron ore mine is undertaking a high wall cut-back to improve stability and allow access to deeper ore deposits. Several sections of the wall have been classified geologically sensitive due to unstable localised geology, and therefore an engineered approach to vibration critical blasting was required. The use of electronic detonators allowed multiple signature (seed) holes to be incorporated into a production blast adjacent to the geologically sensitive area, therefore providing baseline vibration data to be used for future modelling with the added advantage of eliminating unnecessary pit closure downtime typically associated with a signature hole program. All subsequent blast patterns also incorporated multiple signature holes to provide additional data and allow continual updating – and therefore improved accuracy - of the blast prediction model.

Jan 1, 2018

By M J. Daniel

Mineral resources all over the world are often heterogeneous and have variable ore properties and ore grade. As a result the ore processed in concentrating plants varies over the life of mines. Consequently the circuits often suffer from bottlenecks typically at the stages of crushing, semi-autogeneous (SAG) and ball milling. Bottlenecks may be remedied with equipment retrofits, however, design engineers should consider a phased approach to the circuit design that delays initial capital expenditure over the life-of-mine. This paper deals with the debottlenecking of existing mineral processing plants by means of high pressure grinding roll (HPGR) applications. It also deals with the use of innovative flow sheet designs using HPGRs for the design of Greenfield plants by engineering or mining companies. In the case of Greenfield plant design an analysis with respect to energy efficiency and operating cost (OPEX) is presented. The analysis compares the performance of SAG based circuits against HPGR circuits that may be influenced by variable ore properties. Globally about 600 HPGRs are installed in various applications in the cement and minerals industries. In excess of 100 of these HPGRs are used since the mid 1980s for crushing and grinding of various ore types including æhard rockÆ applications. HPGR technology is mature enough to be considered as an ideal debottlenecking device. HPGRÆs are versatile, they have a low installation footprint and they are flexible in its machine settings (pressure, roll speed), which can be adjusted to react to ore variations whilst maintaining a high throughput. Examples for the benefits of using HPGR in terms of energy efficiency and operating costs are presented by this paper. æEco-efficientÆ flow sheets and sustainable development initiatives are linked to energy savings as an æenergy costÆ and benefit to the environment. Energy savingsÆ can also be analysed in terms of the ædollar costÆ (OPEX) savings. This paper demonstrates that HPGR is more energy efficient and may reduce the overall grinding energy requirements in the order of 16 per cent depending on the target grind size and ore properties. The HPGR is more cost efficient and may reduce overall grinding costs by as much as 19.3 per cent depending on the cost of energy, grinding media and the rate of grinding media wear in the comminution circuit.

Jan 1, 2009

By S. E. Phillipson

Underground mine mapping is a critical component of understanding the controls on ground instability. Many relatively localized examples of ground failure are associated with geologic features, such as faults, joints, compaction zones, or sedimentological transition zones. In contrast, long-running, directional roof falls are associated with regionally directed horizontal stress fields, which are induced by tectonic plate interactions in the earth?s crust. When stress-related features are distinguished from geological features, underground mapping can be an effective method for inferring the direction of horizontal stress at individual mines. Comparisons with data compiled in the World Stress Map confirm that underground mapping can be a valid method for determining the orientation of maximum principal horizontal stress at a variety of scales, ranging from individual mines to an entire mining district or coal basin. Comparisons are presented between the maximum horizontal stress directions inferred by MSHA?s Roof Control Division through underground mapping and the azimuths of maximum horizontal stress in the World Stress Map database for North America?s Pennsylvanian-aged Appalachian, Illinois, Black Warrior, and Arkoma Basin coal fields. The comparison indicates that azimuths are similar for both data sets, even where variations in the direction of horizontal stress are present. It is interpreted that inconsistencies in direction are attributable to near-surface affects such as deeply incised stream valleys, or to fault zones that represent heterogeneities in the crust.

Jan 1, 2009

By Dale Preece, Ayman Tawadrous

This paper presents a number of examples of three-dimensional blast modeling in both surface and underground environments that include time-delay explosive decking. These examples include: 1) quarry blasting, 2) coal seam protection blasting, 3) mineral mine blasting with high energy time delayed decks, and, 4) underground single-level/single-shot drawbell blasting.

Jan 1, 2014

By Lyman G. J

Dense medium drum separator efficiency was analysed at two Western Australian iron ore concentrators. Efficiency data had hitherto been difficult to accumulate due to the high cost of analysing representative, and therefore large, coarse ore samples. To overcome this problem, recoverable density tracers, which are in effect artificial mineral and gangue, were manufactured in three different sizes (15 mm, 30 mm and 60 mm). Their use enabled partition curves to be studied within one hour of conducting a test: separation densities were generally lower than the feed medium density for all three sizes of density tracer. For a given set of operating conditions, the smaller tracers had lower separation densities and larger ecart probab/es than the large tracers. These phenomena are explained with the aid of a conceptual model of a drum separator, which assumes that the feed ore plunges to the bottom of the drum upon introduction. Particle rising velocities are, therefore, process determining.Medium rheology was altered by adjusting the proportion of solids in the pulp. This was accomplished by changing both the pulp density and ferrosilicon/magnetite ratio. Higher solids volume fractions invariably caused a decrease in separation densities and an increase in ecart probables, most markedly for the smaller tracers. A similar response was observed when feed tonnages were raised.An explanation for these phenomena is sought in the discussion which also suggests means of improving drum separator efficiency.

Jan 1, 1987

By V. B. Achanti, A. W. Khair

Laboratory studies were carried out at West Virginia University to investigate the rock fragmentation mechanism by continuous miners using an automated rotary cutting simulator. The primary factors influencing the fragmentation process were found to be: bit spacing, bit geometry, depth of cut and cutting drum rotational speed. This paper presents the influence of these parameters in achieving optimum energy consumption and minimizing dust generation during rock fragmentation process. Tree bits were used simultaneously on Indiana limestone while the bit tip angle was varied from 60° to 900. Bit spacing was varied from 2.54 cm (1 in.) to 5.08 cm (2 in.) while the cutting process was assessed for varying cutting depths. Restorable dust generated during the course of the experiments was analyzed utilizing cascade impactors. Assessment of these parameters has led to a better understanding of the cutting mechanism by continuous miners in terms of energy consumption and dust generation.

Feb 24, 1997

By J. J. Stacey

Large mining companies generally follow the distributed ownership corporate model, with a board of directors responsible for decisions that affect both shareholder value and stakeholders of the company. The board is simultaneously responsible for setting the culture and values of the corporation, which drive performance and priorities. Companies listed on the Johannesburg Securities Exchange (JSE) commit to sustainable development in various ways, either by virtue of implementing the King Code of Governance 2009 (King III) and/or through their own public reporting on social and environmental matters. Many mining companies make public statements regarding their support for environmental stewardship, ethical behaviour, and fair treatment of communities. It is a local, regional, and indeed, global phenomenon that companies fail to deliver on these statements. Research was carried out through the Institute of Directors of Southern Africa in 2007, and followed up in 2012, regarding directors? understanding of sustainable development issues, the relative priorities, what is needed for ?radical change? to effect sustainable development, and what enables or constrains the latter. Pertinent findings of both surveys are presented in this paper, and it is suggested that ?on-the-ground? performance may be indicative of the nature of leadership and decisions in the topmost ranks of the company. The results indicated that environmental concerns fall consistently below social issues. Financial capital ranked most important, and while environmental issues are recognized as being of strategic concern for the long-term, they ranked as being the lowest importance of all ?Five Capitals? (Financial, Manufactured, Social, Human, and Natural). Social capital ranked second lowest, with black economic empowerment being the only high-priority social issue. There is also evidence that certain companies within the mining sector fail to recognize their absolute dependence on natural resources. Much is made in academic and popular literature of the need for a new type of leadership for the radical shift to sustainable development: at company level this implies therefore a new type of director. The research found that only 14 per cent of directors felt that board decisions are consistent with their personal values; while intentions are strong to behave ethically and serve sustainable development, actions to give effect to these intentions lag significantly. Respondents indicated that the top impediments to courageous leadership for sustainable development related to personal issues of maintaining the image of being a director, fear of appearing weak, fear of being a lone voice, and bowing to board-colleague peer pressure.

Jan 1, 2014

By Gavin Ritson, Chris Ward

"The oil sands industry is still fairly young with the first viable oil sand operation having been started in Alberta in 1960. Since then numerous modifications and improvements have been tried and implemented. The current process makes use of high velocity pumping of oil sands slurry with hot water (hydrotransport) to achieve separation of bitumen from the sand.A number of the oil sands processes have been adapted from unit operations that are used in mineral processing, such as crushing, screening, flotation, cycloning and thickening. This paper outlines a typical oil sands process flowsheet and investigates the differences and similarities in technologies and costs to other mineral processing industries. It also considers the very large throughputs required, and presents some of the difficulties and challenges currently faced by the industry as a result of high demand for oil and environmental pressures.INTRODUCTIONOil sands (also known as tar sands) deposits are found throughout the world. The Athabasca Oil Sands deposit in Aberta is the largest of these. Oil sands consist of a mixture of crude bitumen (a semi-solid form of crude oil), silica sand, clay minerals, and water. The Athabasca, Peace River and Cold Lake deposits cover 141,000 square kilometers and contain about 1.7 trillion barrels (270×109 m3) of bitumen in-place, comparable in magnitude to the world's total proven reserves of conventional oil"

Jan 1, 2009

By Hans de Ruiter

"Delft University of Technology, RWTH Aachen, Helsinki University of Technology and Imperial College established the Federation of European Mineral Programs (FEMP) in 1999 as a legal body to coordinate joint M.Sc. education.By 2003 the number of participating universities in Europe has grown to 9 (in 7 countries) offering 3 different M.Sc. joint programs. Furthermore students from 8 universities in the USA, Canada, Australia and Chile participate through exchange agreements. About 25 companies are associated with FEMP. Further expansion with other clusters of universities is being investigated.So far some 160 students have taken the programs and are working in all parts of the world in a variety of jobs.The European Commission has recently announced the new “Erasmus World” program that will stimulate the offering of joint programs by European universities and offer third-country students and teachers a greater opportunity for mobility and an enhanced European added value. Host European postgraduate courses will be selected for a five-year period. They will receive funding from the Community and a “EU” seal. Around 250 “EU Masters Courses” will be established.The envisaged new Erasmus program and it’s network and operating practices are very similar to those being used by EMC, EMEC and EGEC. Erasmus World therefore offers a great opportunity for further developments with FEMP as the official body.INTRODUCTIONThe current situation in Europe is that globalisation of the supply of mineral resources has caused the larger mining and the manufacturing companies to expand and invest particularly outside Europe. However these industries still have a great significance for the European Union and its members, which means that mineral engineering know-how is still important in the E.U. It was therefore realised in the mid-nineties that is vital to maintain the very high level of knowledge and skill base in mining engineering and mineral technology that currently exists in the E.U., through good and well-balanced education programs."

Jan 1, 2004

By L Reynolds

Oceana Gold (New Zealand) Limited (OceanaGold) has commenced mining operations at the Globe-Progress mine in the Reefton Goldfield, an area that historically produced 2.1 million ounces of gold from underground quartz lode deposits. During the construction phase of the operation, advanced exploration programmes targeting near-mine prospects commenced. The focus of this ongoing exploration is the discovery of near surface, refractory gold deposits that are amenable to open-pit mining methods and treatment through the Globe-Progress process plant.   One such discovery is the Supreme deposit, located along strike approximately 3 kilometres to the south of the Globe-Progress mine. The Supreme area was tested extensively with diamond drilling in 2006, defining a deposit with similar mineralisation styles and grade to the Globe-Progress deposit. The mineralisation comprises a central core of gold-bearing quartz veins, locally containing visible gold, surrounded by a more extensive halo of refractory, disseminated gold associated with an arsenopyrite-pyrite sulphide mineral assemblage. Three subparallel mineralised structures host the mineralisation. These structures are highly oblique to the country rock orientations, extending approximately 250 metres along a northeast-southwest strike and at least 220 metres down-dip, with an average thickness of 12 metres and moderate dip to the southeast. Records of historical workings indicate that mineralisation extends further down-dip and remains open at depth. 5175 ounces of gold were mined historically at the Supreme deposit. OceanaGold have defined an Inferred Resource for the Supreme deposit of 0.84 million tonnes at 1.46 grams per tonne for a total of 40 000 ounces (at a 0.8 grams per tonne cut-off). Higher-grade zones of mineralisation exist within the deposit and further drilling is planned to test the extent, continuity and geological controls of the mineralised structures.

Jan 1, 2007

By W. J. Verner, J. R. Lucas

Billions of tons of bulk solid materials are processed through our industrial plants each year, and the tonnage is steadily rising. It has been estimated that for every dollar spent in industry as a whole, approxinlately 30 cents is consumed in the handling of bulk solid materials. It is in this category that tremendous savings are possible through the use of improved techniques. Since World War 11, the mining, steel, chemical, and grain industries, among others have made use of increased materials-handling automation in order to gain some of these savings. However, in a chain of automatic operations, every link must be completely reliable, for if there is a single failure, the whole system immediately becomes ineffective. Only too often the weak link in the chain proves to be the flow of bulk solids from bins. To contribute to the fundamental knowledge in this area, a research study has been continuing at The Ohio State University. The principal objective of the investigation has been to study the internal stresses existing in confined bulk solids. LITERATURE SURVEY Literature studies have revealed that many outstanding people have made contributions to the field of bulk solids. For instance, C. F. Jenkin,1 suggested: a. The pressure on a bin wall is not directly proportional to the depth beneath the surface of material in the bin. b. The vertical pressure distribution on the base of a bin is not actually uniform but is a variable. c. Arches form in bins as a result of very small deformations of the material in the bin. This deformation causes a series of gaps to appear, and consequently causes the disappearance of diagonal forces that cannot act across these gaps. The removal of the diagonal forces causes horizontal forces to be introduced which seem to be the chief cause of arching. 11. A. Janssen,4 in 1895 in connection with his experiments on bins, derived a differential equation to describe both the lateral and vertical pressure in bins with vertical sides. This represents a significant contribution to bulk solid theory, and thus its solution is reproduced as follows: L = KV = RW/U' [l-e -U'KY/R] I where L is the lateral pressure of the bulk solid in psf., V is the vertical pressure of the bulk solid in psf., K is the ratio of the lateral pressure to the vertical pressure at any point, R is the hydraulic radius of the bin in feet, W is the density of the bulk solid in lbs. per cubic feet, U' is the coefficient of friction between the stored material and the bin wall, and Y is the head of material above the point in question in feet. In 1903, Jamieson,6 in an elaborate series of experiments on full sized bins measured vertical and lateral pressures by hydraulic diaphragms. He determined many values for mediums of corn, wheat, peas, and flaxseed. In 1951, Caughey, Tooles, and scheer3 measured both lateral and vertical pressure in deep bins by using strain guages on steel bands. Values were calculated for cement, gravel, sand, soy beans, shelled corn

Jan 1, 1961

Traditionally, the gravity cleaning of coal has been evaluated in pilot plant tests. Attention is now turning to the development of empirical models of gravity cleaning equipment that can be used for the design and evaluation of circuits. This paper presents some preliminary information for spirals and water-only cyclones treating fine coals. Also discussed is how such information gives a better understanding of the operating and performance characteristics of this equipment, how realistic comparisons can be made between different types of equipment, and how small mobile plants could be designed for treating the fine coals 'stockpiled' at many NZ mines.

Jan 1, 1985

By E. F. Koppe

The Upper Freeport coal in the Freeport and New Kensington quadrangles, Pennsylvania, varies from a bony streak to a thick coal deposit often exceeding ninety inches, the "Double" or "Thick Freeport". Distinctive basal partings, a central bone layer, and a canneloid top bench may be present. The appearance of a sandstone roof, sandstone rolls, and bony coal at the top of the main coal bench can be anticipated in thin Freeport areas when basal partings are absent. When the two basal partings are present, a shale roof is normal. These effects are correlated with the original topography upon which the coal was deposited. The original depositional high areas tend to coincide with present structural highs. Preliminary data indicate that coal quality, in part, is affected by the deposi-tional setting. In "high" areas, a tendency exists for the main coal bench to contain higher percentages of fusain and mineral matter. Within limits, some-what higher ash fusion temperatures appear to correlate with paleotopographic highs. As a result of these findings, critical examination of the paleotopography and related sediments is indicated in other areas and other coals. The Upper Freeport coal is quite variable both in thickness and composition in the Freeport and New Kensington quadrangles of Pennsylvania (Figure 1). The coal horizon in these quadrangles is marked either by a thin carbonaceous shale bed or by a single bed containing a variable number of partings (binders). The complex coal zone known locally as the "Double" or "Thick Freeport" contains the Upper Freeport Coal Bed at the base; but in addition, it has an overlying bone layer and an upper coal bed occasionally capped with a canneloid layer. The "Thick Freeport" often exceeds 90 inches in thickness, whereas the normal Upper Freeport coal usually varies between 34 and 50 inches.

Jan 1, 1961